@@ -27,14 +27,13 @@
#include <media/v4l2-ctrls.h>
#include <media/v4l2-subdev.h>
-#define OV2680_XVCLK_VALUE 24000000
-
#define OV2680_CHIP_ID 0x2680
#define OV2680_REG_STREAM_CTRL CCI_REG8(0x0100)
#define OV2680_REG_SOFT_RESET CCI_REG8(0x0103)
#define OV2680_REG_CHIP_ID CCI_REG16(0x300a)
+#define OV2680_REG_PLL_MULTIPLIER CCI_REG16(0x3081)
#define OV2680_REG_EXPOSURE_PK CCI_REG24(0x3500)
#define OV2680_REG_R_MANUAL CCI_REG8(0x3503)
@@ -69,6 +68,21 @@ static const char * const ov2680_supply_name[] = {
#define OV2680_NUM_SUPPLIES ARRAY_SIZE(ov2680_supply_name)
+enum {
+ OV2680_19_2_MHZ,
+ OV2680_24_MHZ,
+};
+
+static const unsigned long ov2680_xvclk_freqs[] = {
+ [OV2680_19_2_MHZ] = 19200000,
+ [OV2680_24_MHZ] = 24000000,
+};
+
+static const u8 ov2680_pll_multipliers[] = {
+ [OV2680_19_2_MHZ] = 69,
+ [OV2680_24_MHZ] = 55,
+};
+
struct ov2680_mode_info {
const char *name;
enum ov2680_mode_id id;
@@ -95,6 +109,7 @@ struct ov2680_dev {
struct media_pad pad;
struct clk *xvclk;
u32 xvclk_freq;
+ u8 pll_mult;
struct regulator_bulk_data supplies[OV2680_NUM_SUPPLIES];
struct gpio_desc *pwdn_gpio;
@@ -284,6 +299,11 @@ static int ov2680_stream_enable(struct ov2680_dev *sensor)
{
int ret;
+ ret = cci_write(sensor->regmap, OV2680_REG_PLL_MULTIPLIER,
+ sensor->pll_mult, NULL);
+ if (ret < 0)
+ return ret;
+
ret = regmap_multi_reg_write(sensor->regmap,
ov2680_mode_init_data.reg_data,
ov2680_mode_init_data.reg_data_size);
@@ -699,7 +719,7 @@ static int ov2680_parse_dt(struct ov2680_dev *sensor)
struct device *dev = sensor->dev;
struct gpio_desc *gpio;
unsigned int rate = 0;
- int ret;
+ int i, ret;
/*
* The pin we want is named XSHUTDN in the datasheet. Linux sensor
@@ -747,12 +767,19 @@ static int ov2680_parse_dt(struct ov2680_dev *sensor)
}
sensor->xvclk_freq = rate ?: clk_get_rate(sensor->xvclk);
- if (sensor->xvclk_freq != OV2680_XVCLK_VALUE) {
- dev_err(dev, "wrong xvclk frequency %d HZ, expected: %d Hz\n",
- sensor->xvclk_freq, OV2680_XVCLK_VALUE);
- return -EINVAL;
+
+ for (i = 0; i < ARRAY_SIZE(ov2680_xvclk_freqs); i++) {
+ if (sensor->xvclk_freq == ov2680_xvclk_freqs[i])
+ break;
}
+ if (i == ARRAY_SIZE(ov2680_xvclk_freqs))
+ return dev_err_probe(dev, -EINVAL,
+ "unsupported xvclk frequency %d Hz\n",
+ sensor->xvclk_freq);
+
+ sensor->pll_mult = ov2680_pll_multipliers[i];
+
return 0;
}
Most x86/ACPI boards use the ov2680 with a 19.2 MHz xvclk, rather then the expected 24MHz, add support for this. Compensate for the lower clk by setting a higher PLL multiplier of 69 when using 19.2 MHz vs the default multiplier of 55 for a 24MHz xvclk. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- drivers/media/i2c/ov2680.c | 41 +++++++++++++++++++++++++++++++------- 1 file changed, 34 insertions(+), 7 deletions(-)