diff mbox series

[v3,15/29] media: ov2680: Add support for 19.2 MHz clock

Message ID 20230627131830.54601-16-hdegoede@redhat.com (mailing list archive)
State New, archived
Headers show
Series media: ov2680: Bugfixes + ACPI + selection(crop-tgt) API support | expand

Commit Message

Hans de Goede June 27, 2023, 1:18 p.m. UTC
Most x86/ACPI boards use the ov2680 with a 19.2 MHz xvclk,
rather then the expected 24MHz, add support for this.

Compensate for the lower clk by setting a higher PLL multiplier
of 69 when using 19.2 MHz vs the default multiplier of 55 for
a 24MHz xvclk.

Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/media/i2c/ov2680.c | 41 +++++++++++++++++++++++++++++++-------
 1 file changed, 34 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/drivers/media/i2c/ov2680.c b/drivers/media/i2c/ov2680.c
index a6a83f0e53f3..d4ef34859914 100644
--- a/drivers/media/i2c/ov2680.c
+++ b/drivers/media/i2c/ov2680.c
@@ -27,14 +27,13 @@ 
 #include <media/v4l2-ctrls.h>
 #include <media/v4l2-subdev.h>
 
-#define OV2680_XVCLK_VALUE			24000000
-
 #define OV2680_CHIP_ID				0x2680
 
 #define OV2680_REG_STREAM_CTRL			CCI_REG8(0x0100)
 #define OV2680_REG_SOFT_RESET			CCI_REG8(0x0103)
 
 #define OV2680_REG_CHIP_ID			CCI_REG16(0x300a)
+#define OV2680_REG_PLL_MULTIPLIER		CCI_REG16(0x3081)
 
 #define OV2680_REG_EXPOSURE_PK			CCI_REG24(0x3500)
 #define OV2680_REG_R_MANUAL			CCI_REG8(0x3503)
@@ -69,6 +68,21 @@  static const char * const ov2680_supply_name[] = {
 
 #define OV2680_NUM_SUPPLIES ARRAY_SIZE(ov2680_supply_name)
 
+enum {
+	OV2680_19_2_MHZ,
+	OV2680_24_MHZ,
+};
+
+static const unsigned long ov2680_xvclk_freqs[] = {
+	[OV2680_19_2_MHZ] = 19200000,
+	[OV2680_24_MHZ] = 24000000,
+};
+
+static const u8 ov2680_pll_multipliers[] = {
+	[OV2680_19_2_MHZ] = 69,
+	[OV2680_24_MHZ] = 55,
+};
+
 struct ov2680_mode_info {
 	const char *name;
 	enum ov2680_mode_id id;
@@ -95,6 +109,7 @@  struct ov2680_dev {
 	struct media_pad		pad;
 	struct clk			*xvclk;
 	u32				xvclk_freq;
+	u8				pll_mult;
 	struct regulator_bulk_data	supplies[OV2680_NUM_SUPPLIES];
 
 	struct gpio_desc		*pwdn_gpio;
@@ -284,6 +299,11 @@  static int ov2680_stream_enable(struct ov2680_dev *sensor)
 {
 	int ret;
 
+	ret = cci_write(sensor->regmap, OV2680_REG_PLL_MULTIPLIER,
+			sensor->pll_mult, NULL);
+	if (ret < 0)
+		return ret;
+
 	ret = regmap_multi_reg_write(sensor->regmap,
 				     ov2680_mode_init_data.reg_data,
 				     ov2680_mode_init_data.reg_data_size);
@@ -699,7 +719,7 @@  static int ov2680_parse_dt(struct ov2680_dev *sensor)
 	struct device *dev = sensor->dev;
 	struct gpio_desc *gpio;
 	unsigned int rate = 0;
-	int ret;
+	int i, ret;
 
 	/*
 	 * The pin we want is named XSHUTDN in the datasheet. Linux sensor
@@ -747,12 +767,19 @@  static int ov2680_parse_dt(struct ov2680_dev *sensor)
 	}
 
 	sensor->xvclk_freq = rate ?: clk_get_rate(sensor->xvclk);
-	if (sensor->xvclk_freq != OV2680_XVCLK_VALUE) {
-		dev_err(dev, "wrong xvclk frequency %d HZ, expected: %d Hz\n",
-			sensor->xvclk_freq, OV2680_XVCLK_VALUE);
-		return -EINVAL;
+
+	for (i = 0; i < ARRAY_SIZE(ov2680_xvclk_freqs); i++) {
+		if (sensor->xvclk_freq == ov2680_xvclk_freqs[i])
+			break;
 	}
 
+	if (i == ARRAY_SIZE(ov2680_xvclk_freqs))
+		return dev_err_probe(dev, -EINVAL,
+				     "unsupported xvclk frequency %d Hz\n",
+				     sensor->xvclk_freq);
+
+	sensor->pll_mult = ov2680_pll_multipliers[i];
+
 	return 0;
 }