@@ -245,6 +245,12 @@
{ -1, -1, -1, -1},
};
+static struct em28xx_reg_seq dikom_dk300_digital[] = {
+ {EM28XX_R08_GPIO, 0x6e, ~EM_GPIO_4, 10},
+ {EM2880_R04_GPO, 0x08, 0xff, 10},
+ { -1, -1, -1, -1},
+};
+
/*
* Board definitions
@@ -1673,6 +1679,22 @@
.tuner_gpio = reddo_dvb_c_usb_box,
.has_dvb = 1,
},
+ [EM2882_BOARD_DIKOM_DK300] = {
+ .name = "Dikom DK300",
+ .valid = EM28XX_BOARD_NOT_VALIDATED,
+ .tuner_type = TUNER_XC2028,
+ .tuner_gpio = default_tuner_gpio,
+ .decoder = EM28XX_TVP5150,
+ .mts_firmware = 1,
+ .has_dvb = 1,
+ .dvb_gpio = dikom_dk300_digital,
+ .input = { {
+ .type = EM28XX_VMUX_TELEVISION,
+ .vmux = TVP5150_COMPOSITE0,
+ .amux = EM28XX_AMUX_VIDEO,
+ .gpio = default_analog,
+ } },
+ },
};
const unsigned int em28xx_bcount = ARRAY_SIZE(em28xx_boards);
@@ -1812,6 +1834,7 @@
{0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
{0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
{0x63f653bd, EM2870_BOARD_REDDO_DVB_C_USB_BOX, TUNER_ABSENT},
+ {0x4e913442, EM2882_BOARD_DIKOM_DK300, TUNER_XC2028},
};
/* I2C devicelist hash table for devices with generic USB IDs */
@@ -2168,6 +2191,7 @@
ctl->demod = XC3028_FE_DEFAULT;
break;
case EM2883_BOARD_KWORLD_HYBRID_330U:
+ case EM2882_BOARD_DIKOM_DK300:
ctl->demod = XC3028_FE_CHINA;
ctl->fname = XC2028_DEFAULT_FIRMWARE;
break;
@@ -2480,6 +2504,31 @@
em28xx_gpio_set(dev, dev->board.tuner_gpio);
em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
break;
+
+/*
+ * The Dikom DK300 is detected as an Kworld VS-DVB-T 323UR.
+ *
+ * This occurs because they share identical USB vendor and
+ * product IDs.
+ *
+ * What we do here is look up the EEPROM hash of the Dikom
+ * and if it is found then we decide that we do not have
+ * a Kworld and reset the device to the Dikom instead.
+ *
+ * This solution is only valid if they do not share eeprom
+ * hash identities which has not been determined as yet.
+ */
+ case EM2882_BOARD_KWORLD_VS_DVBT:
+ if (!em28xx_hint_board(dev))
+ em28xx_set_model(dev);
+
+ /* In cases where we had to use a board hint, the call to
+ em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
+ so make the call now so the analog GPIOs are set properly
+ before probing the i2c bus. */
+ em28xx_gpio_set(dev, dev->board.tuner_gpio);
+ em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
+ break;
}
#if defined(CONFIG_MODULES) && defined(MODULE)
@@ -504,6 +504,7 @@
break;
case EM2880_BOARD_TERRATEC_HYBRID_XS:
case EM2881_BOARD_PINNACLE_HYBRID_PRO:
+ case EM2882_BOARD_DIKOM_DK300:
dvb->frontend = dvb_attach(zl10353_attach,
&em28xx_zl10353_xc3028_no_i2c_gate,
&dev->i2c_adap);
@@ -112,6 +112,7 @@
#define EM2861_BOARD_GADMEI_UTV330PLUS 72
#define EM2870_BOARD_REDDO_DVB_C_USB_BOX 73
#define EM2800_BOARD_VC211A 74
+#define EM2882_BOARD_DIKOM_DK300 75
/* Limits minimum and default number of buffers */
#define EM28XX_MIN_BUF 4