@@ -891,10 +891,11 @@ static void dvb_frontend_stop(struct dvb_frontend *fe)
}
/*
- * Sleep until gettimeofday() > waketime + add_usec
- * This needs to be as precise as possible, but as the delay is
- * usually between 2ms and 32ms, it is done using a scheduled msleep
- * followed by usleep (normally a busy-wait loop) for the remainder
+ * Sleep for the amount of time given by add_usec parameter
+ *
+ * This needs to be as precise as possible, as it affects the detection of
+ * the dish tone command at the satellite subsystem. The precision is improved
+ * by using a scheduled msleep followed by udelay for the remainder.
*/
void dvb_frontend_sleep_until(ktime_t *waketime, u32 add_usec)
{
@@ -404,6 +404,11 @@ struct dtv_frontend_properties;
* FE_ENABLE_HIGH_LNB_VOLTAGE ioctl (only Satellite).
* @dishnetwork_send_legacy_command: callback function to implement the
* FE_DISHNETWORK_SEND_LEGACY_CMD ioctl (only Satellite).
+ * Drivers should not use this, except when the DVB
+ * core emulation fails to provide proper support (e.g.
+ * if set_voltage() takes more than 8ms to work), and
+ * when backward compatibility with this legacy API is
+ * required.
* @i2c_gate_ctrl: controls the I2C gate. Newer drivers should use I2C
* mux support instead.
* @ts_bus_ctrl: callback function used to take control of the TS bus.
@@ -693,6 +698,29 @@ extern void dvb_frontend_reinitialise(struct dvb_frontend *fe);
extern int dvb_frontend_suspend(struct dvb_frontend *fe);
extern int dvb_frontend_resume(struct dvb_frontend *fe);
-extern void dvb_frontend_sleep_until(ktime_t *waketime, u32 add_usec);
+/**
+ * dvb_frontend_sleep_until() - Sleep for the amount of time given by
+ * add_usec parameter
+ *
+ * @waketime: pointer to a struct ktime_t
+ * @add_usec: time to sleep, in microseconds
+ *
+ * This function is used to measure the time required for the
+ * %FE_DISHNETWORK_SEND_LEGACY_CMD ioctl to work. It needs to be as precise
+ * as possible, as it affects the detection of the dish tone command at the
+ * satellite subsystem.
+ *
+ * Its used internally by the DVB frontend core, in order to emulate
+ * %FE_DISHNETWORK_SEND_LEGACY_CMD using the &dvb_frontend_ops.set_voltage()
+ * callback.
+ *
+ * NOTE: it should not be used at the drivers, as the emulation for the
+ * legacy callback is provided by the Kernel. The only situation where this
+ * should be at the drivers is when there are some bugs at the hardware that
+ * would prevent the core emulation to work. On such cases, the driver would
+ * be writing a &dvb_frontend_ops.dishnetwork_send_legacy_command() and
+ * calling this function directly.
+ */
+void dvb_frontend_sleep_until(ktime_t *waketime, u32 add_usec);
#endif
This function is used mainly at the DVB core, in order to provide emulation for a legacy ioctl. The only current exception is the stv0299 driver, with takes more than 8ms to switch voltage, breaking the emulation for FE_DISHNETWORK_SEND_LEGACY_CMD. Document that. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> --- drivers/media/dvb-core/dvb_frontend.c | 9 +++++---- drivers/media/dvb-core/dvb_frontend.h | 30 +++++++++++++++++++++++++++++- 2 files changed, 34 insertions(+), 5 deletions(-)