| Message ID | 865b71d4fcf6ce407a94a10d5dcb06944ddb6dcb.1497313626.git-series.kieran.bingham+renesas@ideasonboard.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Kieran, Thanks for your patch, and great work! On 2017-06-13 01:35:07 +0100, Kieran Bingham wrote: > From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > Provide support for the ADV7481 and ADV7482. > > The driver is modelled with 4 subdevices to allow simultaneous streaming > from the AFE (Analog front end) and HDMI inputs though two CSI TX > entities. > > The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked > to the TXB CSI bus. > > The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, > and an earlier rework by Niklas Söderlund. > > Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > --- > > v2: > - Implement DT parsing > - adv748x: Add CSI2 entity > - adv748x: Rework pad allocations and fmts > - Give AFE 8 input pads and move pad defines > - Use the enums to ensure pads are referenced correctly. > - adv748x: Rename AFE/HDMI entities > Now they are 'just afe' and 'just hdmi' > - Reorder the entity enum and structures > - Added pad-format for the CSI2 entities > - CSI2 s_stream pass through > - CSI2 control pass through (with link following) > > v3: > - dt: Extend DT documentation to specify interrupt mappings > - simplify adv748x_parse_dt > - core: Add banner to header file describing ADV748x variants > - Use entity structure pointers rather than global state pointers where > possible > - afe: Reduce indent on afe_status > - hdmi: Add error checking to the bt->pixelclock values. > - Remove all unnecessary pad checks: handled by core > - Fix all probe cleanup paths > - adv748x_csi2_probe() now fails if it has no endpoint > - csi2: Fix small oneliners for is_txa and get_remote_sd() > - csi2: Fix checkpatch warnings > - csi2: Fix up s_stream pass-through > - csi2: Fix up Pixel Rate passthrough > - csi2: simplify adv748x_csi2_get_pad_format() > - Remove 'async notifiers' from AFE/HDMI > Using async notifiers was overkill, when we have access to the > subdevices internally and can register them directly. > - Use state lock in control handlers and clean up s_ctrls > - remove _interruptible mutex locks > > v4: > - all: Convert hex 0xXX to lowercase > - all: Use defines instead of hardcoded register values > - all: Use regmap > - afe, csi2, hdmi: _probe -> _init > - afe, csi2, hdmi: _remove -> _cleanup > - afe, hdmi: Convert pattern generator to a control > - afe, hdmi: get/set-fmt refactor > - afe, hdmi, csi2: Convert to internal calls for pixelrate > - afe: Allow the AFE to configure the Input Select from DT > - afe: Reduce indent on adv748x_afe_status switch > - afe: Remove ununsed macro definitions AIN0-7 > - afe: Remove extraneous control checks handled by core > - afe: Comment fixups > - afe: Rename error label > - afe: Correct control names on the SDP > - afe: Use AIN0-7 rather than AIN1-8 to match ports and MC pads > - core: adv748x_parse_dt references to nodes, and catch multiple > endpoints in a port. > - core: adv748x_dt_cleanup to simplify releasing DT nodes > - core: adv748x_print_info renamed to adv748x_identify_chip > - core: reorganise ordering of probe sequence > - core: No need for of_match_ptr > - core: Fix up i2c read/writes (regmap still on todo list) > - core: Set specific functions from the entities on subdev-init > - core: Use kzalloc for state instead of devm > - core: Improve probe error reporting > - core: Track unknown BIT(6) in tx{a,b}_power > - csi2: Improve adv748x_csi2_get_remote_sd as adv748x_csi2_get_source_sd > - csi2: -EPIPE instead of -ENODEV > - csi2: adv_dbg, instead of adv_info > - csi2: adv748x_csi2_set_format fix > - csi2: remove async notifier and sd member variables > - csi2: register links from the CSI2 > - csi2: create virtual channel helper function > - dt: Remove numbering from endpoints > - dt: describe ports and interrupts as optional > - dt: Re-tab > - hdmi: adv748x_hdmi_have_signal -> adv748x_hdmi_has_signal > - hdmi: fix adv748x_hdmi_read_pixelclock return checks > - hdmi: improve adv748x_hdmi_set_video_timings > - hdmi: Fix tmp variable as polarity > - hdmi: Improve adv748x_hdmi_s_stream > - hdmi: Clean up adv748x_hdmi_s_ctrl register definitions and usage > - hdmi: Fix up adv748x_hdmi_s_dv_timings with macro names for register > - hdmi: Add locking to adv748x_hdmi_g_dv_timings > writes and locking > - hdmi: adv748x_hdmi_set_de_timings function added to clarify DE writes > - hdmi: Use CP in control register naming to match component processor > - hdmi: clean up adv748x_hdmi_query_dv_timings() > - KConfig: Fix up dependency and capitalisation > > > Documentation/devicetree/bindings/media/i2c/adv748x.txt | 96 +- > MAINTAINERS | 6 +- > drivers/media/i2c/Kconfig | 11 +- > drivers/media/i2c/Makefile | 1 +- > drivers/media/i2c/adv748x/Makefile | 7 +- > drivers/media/i2c/adv748x/adv748x-afe.c | 571 ++++++- > drivers/media/i2c/adv748x/adv748x-core.c | 907 +++++++++- > drivers/media/i2c/adv748x/adv748x-csi2.c | 323 +++- > drivers/media/i2c/adv748x/adv748x-hdmi.c | 652 ++++++- > drivers/media/i2c/adv748x/adv748x.h | 415 ++++- > 10 files changed, 2989 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/adv748x.txt > create mode 100644 drivers/media/i2c/adv748x/Makefile > create mode 100644 drivers/media/i2c/adv748x/adv748x-afe.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-core.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-csi2.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-hdmi.c > create mode 100644 drivers/media/i2c/adv748x/adv748x.h > > diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt > new file mode 100644 > index 000000000000..b17f8983c992 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt > @@ -0,0 +1,96 @@ > +* Analog Devices ADV748X video decoder with HDMI receiver > + > +The ADV7481, and ADV7482 are multi format video decoders with an integrated > +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB > +from three input sources HDMI, analog and TTL. > + > +Required Properties: > + > + - compatible: Must contain one of the following > + - "adi,adv7481" for the ADV7481 > + - "adi,adv7482" for the ADV7482 > + > + - reg: I2C slave address > + > +Optional Properties: > + > + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or > + "intrq3". All interrupts are optional. The "intrq3" interrupt > + is only available on the adv7481 > + - interrupts: Specify the interrupt lines for the ADV748x > + > +The device node must contain one 'port' child node per device input and output > +port, in accordance with the video interface bindings defined in > +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes > +are numbered as follows. > + > + Name Type Port > + --------------------------------------- > + AIN0 sink 0 > + AIN1 sink 1 > + AIN2 sink 2 > + AIN3 sink 3 > + AIN4 sink 4 > + AIN5 sink 5 > + AIN6 sink 6 > + AIN7 sink 7 > + HDMI sink 8 > + TTL sink 9 > + TXA source 10 > + TXB source 11 > + > +The digital output port nodes must contain at least one endpoint. > + > +Ports are optional if they are not connected to anything at the hardware level, > +but the driver may not provide any support for ports which are not described. > + > +Example: > + > + video_receiver@70 { > + compatible = "adi,adv7482"; > + reg = <0x70>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&gpio6>; > + interrupt-names = "intrq1", "intrq2"; > + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, > + <31 IRQ_TYPE_LEVEL_LOW>; > + > + port@7 { > + reg = <7>; > + > + adv7482_ain7: endpoint { > + remote-endpoint = <&cvbs_in>; > + }; > + }; > + > + port@8 { > + reg = <8>; > + > + adv7482_hdmi: endpoint { > + remote-endpoint = <&hdmi_in>; > + }; > + }; > + > + port@10 { > + reg = <10>; > + > + adv7482_txa: endpoint { > + clock-lanes = <0>; > + data-lanes = <1 2 3 4>; > + remote-endpoint = <&csi40_in>; > + }; > + }; > + > + port@11 { > + reg = <11>; > + > + adv7482_txb: endpoint { > + clock-lanes = <0>; > + data-lanes = <1>; > + remote-endpoint = <&csi20_in>; > + }; > + }; > + }; > diff --git a/MAINTAINERS b/MAINTAINERS > index eaaa35419fa2..7e2b65240a6f 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -776,6 +776,12 @@ L: linux-media@vger.kernel.org > S: Maintained > F: drivers/media/i2c/adv7511* > > +ANALOG DEVICES INC ADV748X DRIVER > +M: Kieran Bingham <kieran.bingham@ideasonboard.com> > +L: linux-media@vger.kernel.org > +S: Maintained > +F: drivers/media/i2c/adv748x/* > + > ANALOG DEVICES INC ADV7604 DRIVER > M: Hans Verkuil <hans.verkuil@cisco.com> > L: linux-media@vger.kernel.org > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 7c23b7a1fd05..fcbec4273fef 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -204,6 +204,17 @@ config VIDEO_ADV7183 > To compile this driver as a module, choose M here: the > module will be called adv7183. > > +config VIDEO_ADV748X > + tristate "Analog Devices ADV748x decoder" > + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API > + depends on OF > + ---help--- > + V4L2 subdevice driver for the Analog Devices > + ADV7481 and ADV7482 HDMI/Analog video decoders. > + > + To compile this driver as a module, choose M here: the > + module will be called adv748x. > + > config VIDEO_ADV7604 > tristate "Analog Devices ADV7604 decoder" > depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index 62323ec66be8..e0e6045a2ec8 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o > obj-$(CONFIG_VIDEO_ADV7183) += adv7183.o > obj-$(CONFIG_VIDEO_ADV7343) += adv7343.o > obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o > +obj-$(CONFIG_VIDEO_ADV748X) += adv748x/ > obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o > obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o > obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o > diff --git a/drivers/media/i2c/adv748x/Makefile b/drivers/media/i2c/adv748x/Makefile > new file mode 100644 > index 000000000000..c0711e076f1d > --- /dev/null > +++ b/drivers/media/i2c/adv748x/Makefile > @@ -0,0 +1,7 @@ > +adv748x-objs := \ > + adv748x-afe.o \ > + adv748x-core.o \ > + adv748x-csi2.o \ > + adv748x-hdmi.o > + > +obj-$(CONFIG_VIDEO_ADV748X) += adv748x.o > diff --git a/drivers/media/i2c/adv748x/adv748x-afe.c b/drivers/media/i2c/adv748x/adv748x-afe.c > new file mode 100644 > index 000000000000..28e95b292d9b > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-afe.c > @@ -0,0 +1,571 @@ > +/* > + * Driver for Analog Devices ADV748X 8 channel analog front end (AFE) receiver > + * with standard definition processor (SDP) > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/delay.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/v4l2-dv-timings.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * SDP > + */ > + > +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM 0x0 > +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1 > +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_J_SECAM 0x2 > +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_M_SECAM 0x3 > +#define ADV748X_AFE_STD_NTSC_J 0x4 > +#define ADV748X_AFE_STD_NTSC_M 0x5 > +#define ADV748X_AFE_STD_PAL60 0x6 > +#define ADV748X_AFE_STD_NTSC_443 0x7 > +#define ADV748X_AFE_STD_PAL_BG 0x8 > +#define ADV748X_AFE_STD_PAL_N 0x9 > +#define ADV748X_AFE_STD_PAL_M 0xa > +#define ADV748X_AFE_STD_PAL_M_PED 0xb > +#define ADV748X_AFE_STD_PAL_COMB_N 0xc > +#define ADV748X_AFE_STD_PAL_COMB_N_PED 0xd > +#define ADV748X_AFE_STD_PAL_SECAM 0xe > +#define ADV748X_AFE_STD_PAL_SECAM_PED 0xf > + > +static int adv748x_afe_read_ro_map(struct adv748x_state *state, u8 reg) > +{ > + int ret; > + > + /* Select SDP Read-Only Main Map */ > + ret = sdp_write(state, ADV748X_SDP_MAP_SEL, > + ADV748X_SDP_MAP_SEL_RO_MAIN); > + if (ret < 0) > + return ret; > + > + return sdp_read(state, reg); > +} > + > +static int adv748x_afe_status(struct adv748x_afe *afe, u32 *signal, > + v4l2_std_id *std) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int info; > + > + /* Read status from reg 0x10 of SDP RO Map */ > + info = adv748x_afe_read_ro_map(state, ADV748X_SDP_RO_10); > + if (info < 0) > + return info; > + > + if (signal) > + *signal = info & ADV748X_SDP_RO_10_IN_LOCK ? > + 0 : V4L2_IN_ST_NO_SIGNAL; > + > + if (!std) > + return 0; > + > + /* Standard not valid if there is no signal */ > + if (info & BIT(0)) { > + *std = V4L2_STD_UNKNOWN; > + return 0; > + } > + > + switch (info & 0x70) { > + case 0x00: > + *std = V4L2_STD_NTSC; > + break; > + case 0x10: > + *std = V4L2_STD_NTSC_443; > + break; > + case 0x20: > + *std = V4L2_STD_PAL_M; > + break; > + case 0x30: > + *std = V4L2_STD_PAL_60; > + break; > + case 0x40: > + *std = V4L2_STD_PAL; > + break; > + case 0x50: > + *std = V4L2_STD_SECAM; > + break; > + case 0x60: > + *std = V4L2_STD_PAL_Nc | V4L2_STD_PAL_N; > + break; > + case 0x70: > + *std = V4L2_STD_SECAM; > + break; > + default: > + *std = V4L2_STD_UNKNOWN; > + break; > + } > + > + return 0; > +} > + > +static void adv748x_afe_fill_format(struct adv748x_afe *afe, > + struct v4l2_mbus_framefmt *fmt) > +{ > + v4l2_std_id std; > + > + memset(fmt, 0, sizeof(*fmt)); > + > + fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; > + fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; > + fmt->field = V4L2_FIELD_INTERLACED; > + > + fmt->width = 720; > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, &std); > + else > + std = afe->curr_norm; > + > + fmt->height = std & V4L2_STD_525_60 ? 480 : 576; > +} > + > +static int adv748x_afe_std(v4l2_std_id std) > +{ > + if (std == V4L2_STD_ALL) > + return ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM; > + if (std == V4L2_STD_PAL_60) > + return ADV748X_AFE_STD_PAL60; > + if (std == V4L2_STD_NTSC_443) > + return ADV748X_AFE_STD_NTSC_443; > + if (std == V4L2_STD_PAL_N) > + return ADV748X_AFE_STD_PAL_N; > + if (std == V4L2_STD_PAL_M) > + return ADV748X_AFE_STD_PAL_M; > + if (std == V4L2_STD_PAL_Nc) > + return ADV748X_AFE_STD_PAL_COMB_N; > + if (std & V4L2_STD_PAL) > + return ADV748X_AFE_STD_PAL_BG; > + if (std & V4L2_STD_NTSC) > + return ADV748X_AFE_STD_NTSC_M; > + if (std & V4L2_STD_SECAM) > + return ADV748X_AFE_STD_PAL_SECAM; > + > + return -EINVAL; > +} > + > +static int adv748x_afe_set_video_standard(struct adv748x_state *state, > + v4l2_std_id std) > +{ > + int sdpstd; > + > + sdpstd = adv748x_afe_std(std); > + if (sdpstd < 0) > + return sdpstd; > + > + sdp_clrset(state, ADV748X_SDP_VID_SEL, ADV748X_SDP_VID_SEL_MASK, > + (sdpstd & 0xf) << ADV748X_SDP_VID_SEL_SHIFT); > + > + return 0; > +} > + > +static int adv748x_afe_s_input(struct adv748x_afe *afe, unsigned int input) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + > + return sdp_write(state, ADV748X_SDP_INSEL, input); > +} > + > +static int adv748x_afe_g_pixelaspect(struct v4l2_subdev *sd, > + struct v4l2_fract *aspect) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + v4l2_std_id std; > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, &std); > + else > + std = afe->curr_norm; > + > + if (std & V4L2_STD_525_60) { > + aspect->numerator = 11; > + aspect->denominator = 10; > + } else { > + aspect->numerator = 54; > + aspect->denominator = 59; > + } > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_afe_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, norm); > + else > + *norm = afe->curr_norm; > + > + return 0; > +} > + > +static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_afe_set_video_standard(state, std); > + if (ret == 0) > + afe->curr_norm = std; > + > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + if (afe->streaming) { > + ret = -EBUSY; > + goto unlock; > + } > + > + /* Set auto detect mode */ > + ret = adv748x_afe_set_video_standard(state, V4L2_STD_ALL); > + if (ret) > + goto unlock; > + > + msleep(100); > + > + /* Read detected standard */ > + ret = adv748x_afe_status(afe, NULL, std); > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static int adv748x_afe_g_tvnorms(struct v4l2_subdev *sd, v4l2_std_id *norm) > +{ > + *norm = V4L2_STD_ALL; > + > + return 0; > +} > + > +static int adv748x_afe_g_input_status(struct v4l2_subdev *sd, u32 *status) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_afe_status(afe, status, NULL); > + > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_afe_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret, signal = V4L2_IN_ST_NO_SIGNAL; > + > + mutex_lock(&state->mutex); > + > + if (enable) { > + ret = adv748x_afe_s_input(afe, afe->input); > + if (ret) > + goto unlock; > + } > + > + ret = adv748x_txb_power(state, enable); > + if (ret) > + goto unlock; > + > + afe->streaming = enable; > + > + adv748x_afe_status(afe, &signal, NULL); > + if (signal != V4L2_IN_ST_NO_SIGNAL) > + adv_dbg(state, "Detected SDP signal\n"); > + else > + adv_dbg(state, "Couldn't detect SDP video signal\n"); > + > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static const struct v4l2_subdev_video_ops adv748x_afe_video_ops = { > + .g_std = adv748x_afe_g_std, > + .s_std = adv748x_afe_s_std, > + .querystd = adv748x_afe_querystd, > + .g_tvnorms = adv748x_afe_g_tvnorms, > + .g_input_status = adv748x_afe_g_input_status, > + .s_stream = adv748x_afe_s_stream, > + .g_pixelaspect = adv748x_afe_g_pixelaspect, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + */ > + > +static int adv748x_afe_set_pixelrate(struct adv748x_afe *afe) > +{ > + struct v4l2_subdev *tx; > + unsigned int width, height, fps; > + > + tx = adv748x_get_remote_sd(&afe->pads[ADV748X_AFE_SOURCE]); > + if (!tx) > + return -ENOLINK; > + > + width = 720; > + height = afe->curr_norm & V4L2_STD_525_60 ? 480 : 576; > + fps = afe->curr_norm & V4L2_STD_525_60 ? 30 : 25; > + > + return adv748x_csi2_set_pixelrate(tx, width * height * fps); > +} > + > +static int adv748x_afe_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->index != 0) > + return -EINVAL; > + > + code->code = MEDIA_BUS_FMT_UYVY8_2X8; > + > + return 0; > +} > + > +static int adv748x_afe_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct v4l2_mbus_framefmt *mbusformat; > + > + /* The format of the analog sink pads is nonsensical */ > + if (sdformat->pad != ADV748X_AFE_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + sdformat->format = *mbusformat; > + } else { > + adv748x_afe_fill_format(afe, &sdformat->format); > + adv748x_afe_set_pixelrate(afe); > + } > + > + return 0; > +} > + > +static int adv748x_afe_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct v4l2_mbus_framefmt *mbusformat; > + > + /* The format of the analog sink pads is nonsensical */ > + if (sdformat->pad != ADV748X_AFE_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) > + return adv748x_afe_get_format(sd, cfg, sdformat); > + > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + *mbusformat = sdformat->format; Hum, for the V4L2_SUBDEV_FORMAT_TRY case will this not accept any format provided to the function? Should you not limit this to the device capabilities before assigning it to mbusformat ? > + > + return 0; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_afe_pad_ops = { > + .enum_mbus_code = adv748x_afe_enum_mbus_code, > + .set_fmt = adv748x_afe_set_format, > + .get_fmt = adv748x_afe_get_format, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_afe_ops = { > + .video = &adv748x_afe_video_ops, > + .pad = &adv748x_afe_pad_ops, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Controls > + */ > + > +static const char * const afe_ctrl_frp_menu[] = { > + "Disabled", > + "Default Value", > + "Color Bars", > + "Grey Ramp", > + "Cb Ramp", > + "Cr Ramp", > + "Boundary" > +}; > + > +static int adv748x_afe_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct adv748x_afe *afe = adv748x_ctrl_to_afe(ctrl); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + bool enable; > + int ret; > + > + ret = sdp_write(state, 0x0e, 0x00); > + if (ret < 0) > + return ret; > + > + switch (ctrl->id) { > + case V4L2_CID_BRIGHTNESS: > + ret = sdp_write(state, ADV748X_SDP_BRI, ctrl->val); > + break; > + case V4L2_CID_HUE: > + /* Hue is inverted according to HSL chart */ > + ret = sdp_write(state, ADV748X_SDP_HUE, -ctrl->val); > + break; > + case V4L2_CID_CONTRAST: > + ret = sdp_write(state, ADV748X_SDP_CON, ctrl->val); > + break; > + case V4L2_CID_SATURATION: > + ret = sdp_write(state, ADV748X_SDP_SD_SAT_U, ctrl->val); > + if (ret) > + break; > + ret = sdp_write(state, ADV748X_SDP_SD_SAT_V, ctrl->val); > + break; > + case V4L2_CID_TEST_PATTERN: > + enable = !!ctrl->val; > + > + /* Enable/Disable Color bar test patterns */ > + ret = sdp_clrset(state, ADV748X_SDP_DEF, ADV748X_SDP_DEF_VAL_EN, > + enable); > + if (ret) > + break; > + ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, > + enable ? ctrl->val - 1 : 0); > + break; > + default: > + return -EINVAL; > + } > + > + return ret; > +} > + > +static const struct v4l2_ctrl_ops adv748x_afe_ctrl_ops = { > + .s_ctrl = adv748x_afe_s_ctrl, > +}; > + > +static int adv748x_afe_init_controls(struct adv748x_afe *afe) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + > + v4l2_ctrl_handler_init(&afe->ctrl_hdl, 5); > + > + /* Use our mutex for the controls */ > + afe->ctrl_hdl.lock = &state->mutex; > + > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_BRIGHTNESS, ADV748X_SDP_BRI_MIN, > + ADV748X_SDP_BRI_MAX, 1, ADV748X_SDP_BRI_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_CONTRAST, ADV748X_SDP_CON_MIN, > + ADV748X_SDP_CON_MAX, 1, ADV748X_SDP_CON_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_SATURATION, ADV748X_SDP_SAT_MIN, > + ADV748X_SDP_SAT_MAX, 1, ADV748X_SDP_SAT_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_HUE, ADV748X_SDP_HUE_MIN, > + ADV748X_SDP_HUE_MAX, 1, ADV748X_SDP_HUE_DEF); > + > + v4l2_ctrl_new_std_menu_items(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(afe_ctrl_frp_menu) - 1, > + 0, 0, afe_ctrl_frp_menu); > + > + afe->sd.ctrl_handler = &afe->ctrl_hdl; > + if (afe->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&afe->ctrl_hdl); > + return afe->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&afe->ctrl_hdl); > +} > + > +int adv748x_afe_init(struct adv748x_afe *afe) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + unsigned int i; > + > + afe->input = 0; > + afe->streaming = false; > + afe->curr_norm = V4L2_STD_ALL; > + > + adv748x_subdev_init(&afe->sd, state, &adv748x_afe_ops, > + MEDIA_ENT_F_ATV_DECODER, "afe"); > + > + /* Identify the first connector found as a default input if set */ > + for (i = ADV748X_PORT_AIN0; i <= ADV748X_PORT_AIN7; i++) { > + /* Inputs and ports are 1-indexed to match the data sheet */ > + if (state->endpoints[i]) { > + afe->input = i; > + break; > + } > + } > + > + adv748x_afe_s_input(afe, afe->input); > + > + adv_dbg(state, "AFE Default input set to %d\n", afe->input); > + > + /* Entity pads and sinks are 0-indexed to match the pads */ > + for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++) > + afe->pads[i].flags = MEDIA_PAD_FL_SINK; > + > + afe->pads[ADV748X_AFE_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&afe->sd.entity, ADV748X_AFE_NR_PADS, > + afe->pads); > + if (ret) > + return ret; > + > + ret = adv748x_afe_init_controls(afe); > + if (ret) > + goto error; > + > + return 0; > + > +error: > + media_entity_cleanup(&afe->sd.entity); > + > + return ret; > +} > + > +void adv748x_afe_cleanup(struct adv748x_afe *afe) > +{ > + v4l2_device_unregister_subdev(&afe->sd); > + media_entity_cleanup(&afe->sd.entity); > + v4l2_ctrl_handler_free(&afe->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c > new file mode 100644 > index 000000000000..6e395a4524ec > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-core.c > @@ -0,0 +1,907 @@ > +/* > + * Driver for Analog Devices ADV748X HDMI receiver with AFE > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + * > + * Authors: > + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> > + * Niklas Söderlund <niklas.soderlund@ragnatech.se> > + * Kieran Bingham <kieran.bingham@ideasonboard.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/errno.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/of_graph.h> > +#include <linux/regmap.h> > +#include <linux/v4l2-dv-timings.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * Register manipulation > + */ > + > +static const struct regmap_config adv748x_regmap_cnf[] = { > + { > + .name = "io", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "dpll", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "cp", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "hdmi", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "edid", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "repeater", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "infoframe", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "cec", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "sdp", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + > + { > + .name = "txb", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "txa", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > +}; > + > +static int adv748x_configure_regmap(struct adv748x_state *state, int region) > +{ > + int err; > + > + if (!state->i2c_clients[region]) > + return -ENODEV; > + > + state->regmap[region] = > + devm_regmap_init_i2c(state->i2c_clients[region], > + &adv748x_regmap_cnf[region]); > + > + if (IS_ERR(state->regmap[region])) { > + err = PTR_ERR(state->regmap[region]); > + adv_err(state, > + "Error initializing regmap %d with error %d\n", > + region, err); > + return -EINVAL; > + } > + > + return 0; > +} > + > +/* Default addresses for the I2C pages */ > +static int adv748x_i2c_addresses[ADV748X_PAGE_MAX] = { > + ADV748X_I2C_IO, > + ADV748X_I2C_DPLL, > + ADV748X_I2C_CP, > + ADV748X_I2C_HDMI, > + ADV748X_I2C_EDID, > + ADV748X_I2C_REPEATER, > + ADV748X_I2C_INFOFRAME, > + ADV748X_I2C_CEC, > + ADV748X_I2C_SDP, > + ADV748X_I2C_TXB, > + ADV748X_I2C_TXA, > +}; > + > +static int adv748x_read_check(struct adv748x_state *state, > + int client_page, u8 reg) > +{ > + struct i2c_client *client = state->i2c_clients[client_page]; > + int err; > + unsigned int val; > + > + err = regmap_read(state->regmap[client_page], reg, &val); > + > + if (err) { > + adv_err(state, "error reading %02x, %02x\n", > + client->addr, reg); > + return err; > + } > + > + return val; > +} > + > +int adv748x_read(struct adv748x_state *state, u8 page, u8 reg) > +{ > + return adv748x_read_check(state, page, reg); > +} > + > +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value) > +{ > + return regmap_write(state->regmap[page], reg, value); > +} > + > +/* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX > + * size to one or more registers. > + * > + * A value of zero will be returned on success, a negative errno will > + * be returned in error cases. > + */ > +int adv748x_write_block(struct adv748x_state *state, int client_page, > + unsigned int init_reg, const void *val, > + size_t val_len) > +{ > + struct regmap *regmap = state->regmap[client_page]; > + > + if (val_len > I2C_SMBUS_BLOCK_MAX) > + val_len = I2C_SMBUS_BLOCK_MAX; > + > + return regmap_raw_write(regmap, init_reg, val, val_len); > +} > + > + > +static struct i2c_client *adv748x_dummy_client(struct adv748x_state *state, > + u8 addr, u8 io_reg) > +{ > + struct i2c_client *client = state->client; > + > + if (addr) > + io_write(state, io_reg, addr << 1); > + > + return i2c_new_dummy(client->adapter, io_read(state, io_reg) >> 1); > +} > + > +static void adv748x_unregister_clients(struct adv748x_state *state) > +{ > + unsigned int i; > + > + for (i = 1; i < ARRAY_SIZE(state->i2c_clients); ++i) { > + if (state->i2c_clients[i]) > + i2c_unregister_device(state->i2c_clients[i]); > + } > +} > + > +static int adv748x_initialise_clients(struct adv748x_state *state) > +{ > + int i; > + int ret; > + > + for (i = ADV748X_PAGE_DPLL; i < ADV748X_PAGE_MAX; ++i) { > + state->i2c_clients[i] = > + adv748x_dummy_client(state, adv748x_i2c_addresses[i], > + ADV748X_IO_SLAVE_ADDR_BASE + i); > + if (state->i2c_clients[i] == NULL) { > + adv_err(state, "failed to create i2c client %u\n", i); > + return -ENOMEM; > + } > + > + ret = adv748x_configure_regmap(state, i); > + if (ret) > + return ret; > + } > + > + return 0; > +} > + > +/** > + * struct adv748x_reg_value - Register write instruction > + * @page: Regmap page identifier > + * @reg: I2C register > + * @value: value to write to @page at @reg > + */ > +struct adv748x_reg_value { > + u8 page; > + u8 reg; > + u8 value; > +}; > + > +static int adv748x_write_regs(struct adv748x_state *state, > + const struct adv748x_reg_value *regs) > +{ > + int ret; > + > + while (regs->page != ADV748X_PAGE_EOR) { > + if (regs->page == ADV748X_PAGE_WAIT) { > + msleep(regs->value); > + } else { > + ret = adv748x_write(state, regs->page, regs->reg, > + regs->value); > + if (ret < 0) { > + adv_err(state, > + "Error regs page: 0x%02x reg: 0x%02x\n", > + regs->page, regs->reg); > + return ret; > + } > + } > + regs++; > + } > + > + return 0; > +} > + > + > +/* ----------------------------------------------------------------------------- > + * TXA and TXB > + */ > + > +static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = { > + > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = { > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x3b}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = { > + > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ > + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ > + > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = { > + > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x3b}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +int adv748x_txa_power(struct adv748x_state *state, bool on) > +{ > + int val; > + > + val = txa_read(state, ADV748X_CSI_FS_AS_LS); > + if (val < 0) > + return val; > + > + /* > + * This test against BIT(6) is not documented by the datasheet, but was > + * specified in the downstream driver. > + * Track with a WARN_ONCE to determine if it is ever set by HW. > + */ > + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), > + "Enabling with unknown bit set"); > + > + if (on) > + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); > + else > + return adv748x_write_regs(state, adv748x_power_down_txa_4lane); > +} > + > +int adv748x_txb_power(struct adv748x_state *state, bool on) > +{ > + int val; > + > + val = txb_read(state, ADV748X_CSI_FS_AS_LS); > + if (val < 0) > + return val; > + > + /* > + * This test against BIT(6) is not documented by the datasheet, but was > + * specified in the downstream driver. > + * Track with a WARN_ONCE to determine if it is ever set by HW. > + */ > + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), > + "Enabling with unknown bit set"); > + > + if (on) > + return adv748x_write_regs(state, adv748x_power_up_txb_1lane); > + else > + return adv748x_write_regs(state, adv748x_power_down_txb_1lane); > +} > + > +/* ----------------------------------------------------------------------------- > + * Media Operations > + */ > + > +static const struct media_entity_operations adv748x_media_ops = { > + .link_validate = v4l2_subdev_link_validate, > +}; > + > +/* ----------------------------------------------------------------------------- > + * HW setup > + */ > + > +static const struct adv748x_reg_value adv748x_sw_reset[] = { > + > + {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */ > + {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */ > + {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */ > + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_set_slave_address[] = { > + {ADV748X_PAGE_IO, 0xf3, ADV748X_I2C_DPLL << 1}, > + {ADV748X_PAGE_IO, 0xf4, ADV748X_I2C_CP << 1}, > + {ADV748X_PAGE_IO, 0xf5, ADV748X_I2C_HDMI << 1}, > + {ADV748X_PAGE_IO, 0xf6, ADV748X_I2C_EDID << 1}, > + {ADV748X_PAGE_IO, 0xf7, ADV748X_I2C_REPEATER << 1}, > + {ADV748X_PAGE_IO, 0xf8, ADV748X_I2C_INFOFRAME << 1}, > + {ADV748X_PAGE_IO, 0xfa, ADV748X_I2C_CEC << 1}, > + {ADV748X_PAGE_IO, 0xfb, ADV748X_I2C_SDP << 1}, > + {ADV748X_PAGE_IO, 0xfc, ADV748X_I2C_TXB << 1}, > + {ADV748X_PAGE_IO, 0xfd, ADV748X_I2C_TXA << 1}, > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +/* Supported Formats For Script Below */ > +/* - 01-29 HDMI to MIPI TxA CSI 4-Lane - RGB888: */ > +static const struct adv748x_reg_value adv748x_init_txa_4lane[] = { > + /* Disable chip powerdown & Enable HDMI Rx block */ > + {ADV748X_PAGE_IO, 0x00, 0x40}, > + > + {ADV748X_PAGE_REPEATER, 0x40, 0x83}, /* Enable HDCP 1.1 */ > + > + {ADV748X_PAGE_HDMI, 0x00, 0x08},/* Foreground Channel = A */ > + {ADV748X_PAGE_HDMI, 0x98, 0xff},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x99, 0xa3},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9a, 0x00},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9b, 0x0a},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9d, 0x40},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0xcb, 0x09},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3d, 0x10},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3e, 0x7b},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3f, 0x5e},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x4e, 0xfe},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x4f, 0x18},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x57, 0xa3},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x58, 0x04},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x85, 0x10},/* ADI Required Write */ > + > + {ADV748X_PAGE_HDMI, 0x83, 0x00},/* Enable All Terminations */ > + {ADV748X_PAGE_HDMI, 0xa3, 0x01},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0xbe, 0x00},/* ADI Required Write */ > + > + {ADV748X_PAGE_HDMI, 0x6c, 0x01},/* HPA Manual Enable */ > + {ADV748X_PAGE_HDMI, 0xf8, 0x01},/* HPA Asserted */ > + {ADV748X_PAGE_HDMI, 0x0f, 0x00},/* Audio Mute Speed Set to Fastest */ > + /* (Smallest Step Size) */ > + > + {ADV748X_PAGE_IO, 0x04, 0x02}, /* RGB Out of CP */ > + {ADV748X_PAGE_IO, 0x12, 0xf0}, /* CSC Depends on ip Packets, SDR 444 */ > + {ADV748X_PAGE_IO, 0x17, 0x80}, /* Luma & Chroma can reach 254d */ > + {ADV748X_PAGE_IO, 0x03, 0x86}, /* CP-Insert_AV_Code */ > + > + {ADV748X_PAGE_CP, 0x7c, 0x00}, /* ADI Required Write */ > + > + {ADV748X_PAGE_IO, 0x0c, 0xe0}, /* Enable LLC_DLL & Double LLC Timing */ > + {ADV748X_PAGE_IO, 0x0e, 0xdd}, /* LLC/PIX/SPI PINS TRISTATED AUD */ > + /* Outputs Enabled */ > + {ADV748X_PAGE_IO, 0x10, 0xa0}, /* Enable 4-lane CSI Tx & Pixel Port */ > + > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ > + {ADV748X_PAGE_TXA, 0xdb, 0x10}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xd6, 0x07}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xc4, 0x0a}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x71, 0x33}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x72, 0x11}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +/* 02-01 Analog CVBS to MIPI TX-B CSI 1-Lane - */ > +/* Autodetect CVBS Single Ended In Ain 1 - MIPI Out */ > +static const struct adv748x_reg_value adv748x_init_txb_1lane[] = { > + > + {ADV748X_PAGE_IO, 0x00, 0x30}, /* Disable chip powerdown Rx */ > + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ > + > + {ADV748X_PAGE_IO, 0x0e, 0xff}, /* LLC/PIX/AUD/SPI PINS TRISTATED */ > + > + {ADV748X_PAGE_SDP, 0x0f, 0x00}, /* Exit Power Down Mode */ > + {ADV748X_PAGE_SDP, 0x52, 0xcd}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x0e, 0x80}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x9c, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x9c, 0xff}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x0e, 0x00}, /* ADI Required Write */ > + > + /* ADI recommended writes for improved video quality */ > + {ADV748X_PAGE_SDP, 0x80, 0x51}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x81, 0x51}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x82, 0x68}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x03, 0x42}, /* Tri-S Output , PwrDwn 656 pads */ > + {ADV748X_PAGE_SDP, 0x04, 0xb5}, /* ITU-R BT.656-4 compatible */ > + {ADV748X_PAGE_SDP, 0x13, 0x00}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x17, 0x41}, /* Select SH1 */ > + {ADV748X_PAGE_SDP, 0x31, 0x12}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0xe6, 0x4f}, /* V bit end pos manually in NTSC */ > + > + /* Enable 1-Lane MIPI Tx, */ > + /* enable pixel output and route SD through Pixel port */ > + {ADV748X_PAGE_IO, 0x10, 0x70}, > + > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ > + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ > + {ADV748X_PAGE_TXB, 0xd2, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xc4, 0x0a}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x71, 0x33}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x72, 0x11}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static int adv748x_reset(struct adv748x_state *state) > +{ > + int ret; > + > + ret = adv748x_write_regs(state, adv748x_sw_reset); > + if (ret < 0) > + return ret; > + > + ret = adv748x_write_regs(state, adv748x_set_slave_address); > + if (ret < 0) > + return ret; > + > + /* Init and power down TXA */ > + ret = adv748x_write_regs(state, adv748x_init_txa_4lane); > + if (ret) > + return ret; > + > + adv748x_txa_power(state, 0); > + > + /* Init and power down TXB */ > + ret = adv748x_write_regs(state, adv748x_init_txb_1lane); > + if (ret) > + return ret; > + > + adv748x_txb_power(state, 0); > + > + /* Disable chip powerdown & Enable HDMI Rx block */ > + io_write(state, ADV748X_IO_PD, ADV748X_IO_PD_RX_EN); > + > + /* Enable 4-lane CSI Tx & Pixel Port */ > + io_write(state, ADV748X_IO_10, ADV748X_IO_10_CSI4_EN | > + ADV748X_IO_10_CSI1_EN | > + ADV748X_IO_10_PIX_OUT_EN); > + > + /* Use vid_std and v_freq as freerun resolution for CP */ > + cp_clrset(state, ADV748X_CP_CLMP_POS, ADV748X_CP_CLMP_POS_DIS_AUTO, > + ADV748X_CP_CLMP_POS_DIS_AUTO); > + > + return 0; > +} > + > +static int adv748x_identify_chip(struct adv748x_state *state) > +{ > + int msb, lsb; > + > + lsb = io_read(state, ADV748X_IO_CHIP_REV_ID_1); > + msb = io_read(state, ADV748X_IO_CHIP_REV_ID_2); > + > + if (lsb < 0 || msb < 0) { > + adv_err(state, "Failed to read chip revision\n"); > + return -EIO; > + } > + > + adv_info(state, "chip found @ 0x%02x revision %02x%02x\n", > + state->client->addr << 1, lsb, msb); > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * i2c driver > + */ > + > +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, > + const struct v4l2_subdev_ops *ops, u32 function, > + const char *ident) > +{ > + v4l2_subdev_init(sd, ops); > + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + > + /* the owner is the same as the i2c_client's driver owner */ > + sd->owner = state->dev->driver->owner; > + sd->dev = state->dev; > + > + v4l2_set_subdevdata(sd, state); > + > + /* initialize name */ > + snprintf(sd->name, sizeof(sd->name), "%s %d-%04x %s", > + state->dev->driver->name, > + i2c_adapter_id(state->client->adapter), > + state->client->addr, ident); > + > + sd->entity.function = function; > + sd->entity.ops = &adv748x_media_ops; > +} > + > +static int adv748x_parse_dt(struct adv748x_state *state) > +{ > + struct device_node *ep_np = NULL; > + struct of_endpoint ep; > + bool found = false; > + > + for_each_endpoint_of_node(state->dev->of_node, ep_np) { > + of_graph_parse_endpoint(ep_np, &ep); > + adv_info(state, "Endpoint %s on port %d", > + of_node_full_name(ep.local_node), > + ep.port); > + > + if (ep.port >= ADV748X_PORT_MAX) { > + adv_err(state, "Invalid endpoint %s on port %d", > + of_node_full_name(ep.local_node), > + ep.port); > + > + continue; > + } > + > + if (state->endpoints[ep.port]) { > + adv_err(state, > + "Multiple port endpoints are not supported"); > + continue; > + } > + > + of_node_get(ep_np); > + state->endpoints[ep.port] = ep_np; > + > + found = true; > + } > + > + return found ? 0 : -ENODEV; > +} > + > +static void adv748x_dt_cleanup(struct adv748x_state *state) > +{ > + unsigned int i; > + > + for (i = 0; i < ADV748X_PORT_MAX; i++) > + of_node_put(state->endpoints[i]); > +} > + > +static int adv748x_setup_links(struct adv748x_state *state) > +{ > + int ret; > + int enabled = MEDIA_LNK_FL_ENABLED; > + > +/* > + * HACK/Workaround: > + * > + * Currently non-immutable link resets go through the RVin > + * driver, and cause the links to fail, due to not being part of RVIN. > + * As a temporary workaround until the RVIN driver knows better than to parse > + * links that do not belong to it, use static immutable links for our internal > + * media paths. > + */ The problem is a bigger then just the VIN ignoring the links not belonging to it self I think. The ADV7482 driver must have a link notification handler to deal with the links that belong to it. Else if all links of the media device is reset there is no way to setup the links between the different ADV7482 subdevices, or am I missing something? > +#define ADV748x_DEV_STATIC_LINKS > +#ifdef ADV748x_DEV_STATIC_LINKS > + enabled |= MEDIA_LNK_FL_IMMUTABLE; > +#endif > + > + /* TXA - Default link is with HDMI */ > + ret = media_create_pad_link(&state->hdmi.sd.entity, 1, > + &state->txa.sd.entity, 0, enabled); > + if (ret) { > + adv_err(state, "Failed to create HDMI-TXA pad link"); > + return ret; > + } > + > +#ifndef ADV748x_DEV_STATIC_LINKS > + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, > + &state->txa.sd.entity, 0, 0); > + if (ret) { > + adv_err(state, "Failed to create AFE-TXA pad link"); > + return ret; > + } > +#endif > + > + /* TXB - Can only output from the AFE */ > + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, > + &state->txb.sd.entity, 0, enabled); > + if (ret) { > + adv_err(state, "Failed to create AFE-TXB pad link"); > + return ret; > + } > + > + return 0; > +} > + > +int adv748x_register_subdevs(struct adv748x_state *state, > + struct v4l2_device *v4l2_dev) > +{ > + int ret; > + > + ret = v4l2_device_register_subdev(v4l2_dev, &state->hdmi.sd); > + if (ret < 0) > + return ret; > + > + ret = v4l2_device_register_subdev(v4l2_dev, &state->afe.sd); > + if (ret < 0) > + goto err_unregister_hdmi; > + > + ret = adv748x_setup_links(state); > + if (ret < 0) > + goto err_unregister_afe; > + > + return 0; > + > +err_unregister_afe: > + v4l2_device_unregister_subdev(&state->afe.sd); > +err_unregister_hdmi: > + v4l2_device_unregister_subdev(&state->hdmi.sd); > + > + return ret; > +} > + > +static int adv748x_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct adv748x_state *state; > + int ret; > + > + /* Check if the adapter supports the needed features */ > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) > + return -EIO; > + > + state = kzalloc(sizeof(struct adv748x_state), GFP_KERNEL); > + if (!state) > + return -ENOMEM; > + > + mutex_init(&state->mutex); > + > + state->dev = &client->dev; > + state->client = client; > + state->i2c_clients[ADV748X_PAGE_IO] = client; > + i2c_set_clientdata(client, state); > + > + /* Discover and process ports declared by the Device tree endpoints */ > + ret = adv748x_parse_dt(state); > + if (ret) { > + adv_err(state, "Failed to parse device tree"); > + goto err_free_mutex; > + } > + > + /* Configure IO Regmap region */ > + ret = adv748x_configure_regmap(state, ADV748X_PAGE_IO); > + if (ret) { > + adv_err(state, "Error configuring IO regmap region"); > + goto err_cleanup_dt; > + } > + > + ret = adv748x_identify_chip(state); > + if (ret) { > + adv_err(state, "Failed to identify chip"); > + goto err_cleanup_clients; > + } > + > + /* Configure remaining pages as I2C clients with regmap access */ > + ret = adv748x_initialise_clients(state); > + if (ret) { > + adv_err(state, "Failed to setup client regmap pages"); > + goto err_cleanup_clients; > + } > + > + /* SW reset ADV748X to its default values */ > + ret = adv748x_reset(state); > + if (ret) { > + adv_err(state, "Failed to reset hardware"); > + goto err_cleanup_clients; > + } > + > + /* Initialise HDMI */ > + ret = adv748x_hdmi_init(&state->hdmi); > + if (ret) { > + adv_err(state, "Failed to probe HDMI"); > + goto err_cleanup_clients; > + } > + > + /* Initialise AFE */ > + ret = adv748x_afe_init(&state->afe); > + if (ret) { > + adv_err(state, "Failed to probe AFE"); > + goto err_cleanup_hdmi; > + } > + > + /* Initialise TXA */ > + ret = adv748x_csi2_init(state, &state->txa); > + if (ret) { > + adv_err(state, "Failed to probe TXA"); > + goto err_cleanup_afe; > + } > + > + /* Initialise TXB */ > + ret = adv748x_csi2_init(state, &state->txb); > + if (ret) { > + adv_err(state, "Failed to probe TXB"); > + goto err_cleanup_txa; > + } > + > + return 0; > + > +err_cleanup_txa: > + adv748x_csi2_cleanup(&state->txa); > +err_cleanup_afe: > + adv748x_afe_cleanup(&state->afe); > +err_cleanup_hdmi: > + adv748x_hdmi_cleanup(&state->hdmi); > +err_cleanup_clients: > + adv748x_unregister_clients(state); > +err_cleanup_dt: > + adv748x_dt_cleanup(state); > +err_free_mutex: > + mutex_destroy(&state->mutex); > + kfree(state); > + > + return ret; > +} > + > +static int adv748x_remove(struct i2c_client *client) > +{ > + struct adv748x_state *state = i2c_get_clientdata(client); > + > + adv748x_afe_cleanup(&state->afe); > + adv748x_hdmi_cleanup(&state->hdmi); > + > + adv748x_csi2_cleanup(&state->txa); > + adv748x_csi2_cleanup(&state->txb); > + > + adv748x_unregister_clients(state); > + adv748x_dt_cleanup(state); > + mutex_destroy(&state->mutex); > + > + kfree(state); > + > + return 0; > +} > + > +static const struct i2c_device_id adv748x_id[] = { > + { "adv7481", 0 }, > + { "adv7482", 0 }, > + { }, > +}; > + > +static const struct of_device_id adv748x_of_table[] = { > + { .compatible = "adi,adv7481", }, > + { .compatible = "adi,adv7482", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, adv748x_of_table); > + > +static struct i2c_driver adv748x_driver = { > + .driver = { > + .name = "adv748x", > + .of_match_table = adv748x_of_table, > + }, > + .probe = adv748x_probe, > + .remove = adv748x_remove, > + .id_table = adv748x_id, > +}; > + > +module_i2c_driver(adv748x_driver); > + > +MODULE_AUTHOR("Kieran Bingham <kieran.bingham@ideasonboard.com>"); > +MODULE_DESCRIPTION("ADV748X video decoder"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/media/i2c/adv748x/adv748x-csi2.c b/drivers/media/i2c/adv748x/adv748x-csi2.c > new file mode 100644 > index 000000000000..a9b7fbd93530 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-csi2.c > @@ -0,0 +1,323 @@ > +/* > + * Driver for Analog Devices ADV748X CSI-2 Transmitter > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/module.h> > +#include <linux/mutex.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +static bool is_txa(struct adv748x_csi2 *tx) > +{ > + return tx == &tx->state->txa; > +} > + > +static int adv748x_csi2_set_virtual_channel(struct adv748x_csi2 *tx, > + unsigned int vc) > +{ > + return tx_write(tx, ADV748X_CSI_VC_REF, vc << ADV748X_CSI_VC_REF_SHIFT); > +} > + > +/** > + * adv748x_csi2_register_link : Register and link internal entities > + * > + * @tx: CSI2 private entity > + * @v4l2_dev: Video registration device > + * @src: Source subdevice to establish link > + * @src_pad: Pad number of source to link to this @tx > + * @preferred: Specify if this link is preferred over pre-existing links > + * > + * Ensure that the subdevice is registered against the v4l2_device, and link the > + * source pad to the sink pad of the CSI2 bus entity. > + */ > +static int adv748x_csi2_register_link(struct adv748x_csi2 *tx, > + struct v4l2_device *v4l2_dev, > + struct v4l2_subdev *src, > + unsigned int src_pad, > + bool preferred) > +{ > + int enabled = 0; > + int ret; > + > + if (preferred) > + enabled = MEDIA_LNK_FL_ENABLED; > + > + if (!src->v4l2_dev) { > + ret = v4l2_device_register_subdev(v4l2_dev, src); > + if (ret) > + return ret; > + } > + > + return media_create_pad_link(&src->entity, src_pad, > + &tx->sd.entity, ADV748X_CSI2_SINK, > + enabled); > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_internal_ops > + * > + * We use the internal registered operation to be able to ensure that our > + * incremental subdevices (not connected in the forward path) can be registered > + * against the resulting video path and media device. > + */ > + > +static int adv748x_csi2_registered(struct v4l2_subdev *sd) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + int ret; > + > + adv_dbg(state, "Registered %s (%s)", is_txa(tx) ? "TXA":"TXB", > + sd->name); > + > + ret = adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->afe.sd, > + ADV748X_AFE_SOURCE, !is_txa(tx)); > + if (ret) > + return ret; > + > + /* TX-B only supports AFE */ > + if (!is_txa(tx)) > + return 0; > + > + return adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->hdmi.sd, > + ADV748X_HDMI_SOURCE, true); > +} > + > +static const struct v4l2_subdev_internal_ops adv748x_csi2_internal_ops = { > + .registered = adv748x_csi2_registered, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_csi2_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct v4l2_subdev *src; > + > + src = adv748x_get_remote_sd(&tx->pads[ADV748X_CSI2_SINK]); > + if (!src) > + return -EPIPE; > + > + return v4l2_subdev_call(src, video, s_stream, enable); > +} > + > +static const struct v4l2_subdev_video_ops adv748x_csi2_video_ops = { > + .s_stream = adv748x_csi2_s_stream, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + * > + * The CSI2 bus pads are ignorant to the data sizes or formats. > + * But we must support setting the pad formats for format propagation. > + */ > + > +static struct v4l2_mbus_framefmt * > +adv748x_csi2_get_pad_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + unsigned int pad, u32 which) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + > + if (which == V4L2_SUBDEV_FORMAT_TRY) > + return v4l2_subdev_get_try_format(sd, cfg, pad); > + else > + return &tx->format; > +} > + > +static int adv748x_csi2_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + struct v4l2_mbus_framefmt *mbusformat; > + > + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, > + sdformat->which); > + if (!mbusformat) > + return -EINVAL; > + > + mutex_lock(&state->mutex); Why do you need to take the lock here? I'm not saying it's wrong just curious :-) > + > + sdformat->format = *mbusformat; > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_csi2_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + struct v4l2_mbus_framefmt *mbusformat; > + int ret = 0; > + > + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, > + sdformat->which); > + if (!mbusformat) > + return -EINVAL; > + > + mutex_lock(&state->mutex); Also why you need to lock here? > + > + if (sdformat->pad == ADV748X_CSI2_SOURCE) { > + const struct v4l2_mbus_framefmt *sink_fmt; > + > + sink_fmt = adv748x_csi2_get_pad_format(sd, cfg, > + ADV748X_CSI2_SINK, > + sdformat->which); > + > + if (!sink_fmt) { > + ret = -EINVAL; > + goto unlock; > + } > + > + sdformat->format = *sink_fmt; > + } > + > + *mbusformat = sdformat->format; > + > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_csi2_pad_ops = { > + .get_fmt = adv748x_csi2_get_format, > + .set_fmt = adv748x_csi2_set_format, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_csi2_ops = { > + .video = &adv748x_csi2_video_ops, > + .pad = &adv748x_csi2_pad_ops, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Subdev module and controls > + */ > + > +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate) > +{ > + struct v4l2_ctrl *ctrl; > + > + ctrl = v4l2_ctrl_find(sd->ctrl_handler, V4L2_CID_PIXEL_RATE); > + if (!ctrl) > + return -EINVAL; > + > + return v4l2_ctrl_s_ctrl_int64(ctrl, rate); > +} > + > +static int adv748x_csi2_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + switch (ctrl->id) { > + case V4L2_CID_PIXEL_RATE: > + return 0; > + default: > + return -EINVAL; > + } > +} > + > +static const struct v4l2_ctrl_ops adv748x_csi2_ctrl_ops = { > + .s_ctrl = adv748x_csi2_s_ctrl, > +}; > + > +static int adv748x_csi2_init_controls(struct adv748x_csi2 *tx) > +{ > + struct v4l2_ctrl *ctrl; > + > + v4l2_ctrl_handler_init(&tx->ctrl_hdl, 1); > + > + ctrl = v4l2_ctrl_new_std(&tx->ctrl_hdl, &adv748x_csi2_ctrl_ops, > + V4L2_CID_PIXEL_RATE, 1, INT_MAX, 1, 1); > + > + tx->sd.ctrl_handler = &tx->ctrl_hdl; > + if (tx->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > + return tx->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&tx->ctrl_hdl); > +} > + > +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx) > +{ > + struct device_node *ep; > + int ret; > + > + /* We can not use container_of to get back to the state with two TXs */ > + tx->state = state; > + tx->page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB; > + > + ep = state->endpoints[is_txa(tx) ? ADV748X_PORT_TXA : ADV748X_PORT_TXB]; > + if (!ep) { > + adv_err(state, "No endpoint found for %s\n", > + is_txa(tx) ? "txa" : "txb"); > + return -ENODEV; > + } > + > + /* Initialise the virtual channel */ > + adv748x_csi2_set_virtual_channel(tx, 0); > + > + adv748x_subdev_init(&tx->sd, state, &adv748x_csi2_ops, > + MEDIA_ENT_F_UNKNOWN, > + is_txa(tx) ? "txa" : "txb"); > + > + /* Ensure that matching is based upon the endpoint fwnodes */ > + tx->sd.fwnode = of_fwnode_handle(ep); > + > + /* Register internal ops for incremental subdev registration */ > + tx->sd.internal_ops = &adv748x_csi2_internal_ops; > + > + tx->pads[ADV748X_CSI2_SINK].flags = MEDIA_PAD_FL_SINK; > + tx->pads[ADV748X_CSI2_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&tx->sd.entity, ADV748X_CSI2_NR_PADS, > + tx->pads); > + if (ret) > + return ret; > + > + ret = adv748x_csi2_init_controls(tx); > + if (ret) > + goto err_free_media; > + > + ret = v4l2_async_register_subdev(&tx->sd); > + if (ret) > + goto err_free_ctrl; > + > + return 0; > + > +err_free_ctrl: > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > +err_free_media: > + media_entity_cleanup(&tx->sd.entity); > + > + return ret; > +} > + > +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx) > +{ > + v4l2_async_unregister_subdev(&tx->sd); > + media_entity_cleanup(&tx->sd.entity); > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x-hdmi.c b/drivers/media/i2c/adv748x/adv748x-hdmi.c > new file mode 100644 > index 000000000000..8f02c851bbc0 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c > @@ -0,0 +1,652 @@ > +/* > + * Driver for Analog Devices ADV748X HDMI receiver and Component Processor (CP) > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/module.h> > +#include <linux/mutex.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include <uapi/linux/v4l2-dv-timings.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * HDMI and CP > + */ > + > +#define ADV748X_HDMI_MIN_WIDTH 640 > +#define ADV748X_HDMI_MAX_WIDTH 1920 > +#define ADV748X_HDMI_MIN_HEIGHT 480 > +#define ADV748X_HDMI_MAX_HEIGHT 1200 > +#define ADV748X_HDMI_MIN_PIXELCLOCK 0 /* unknown */ > +#define ADV748X_HDMI_MAX_PIXELCLOCK 162000000 > + > +static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = { > + .type = V4L2_DV_BT_656_1120, > + /* keep this initialization for compatibility with GCC < 4.4.6 */ > + .reserved = { 0 }, > + /* Min pixelclock value is unknown */ > + V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH, > + ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT, > + ADV748X_HDMI_MIN_PIXELCLOCK, > + ADV748X_HDMI_MAX_PIXELCLOCK, > + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT, > + V4L2_DV_BT_CAP_INTERLACED | > + V4L2_DV_BT_CAP_PROGRESSIVE) > +}; > + > +struct adv748x_hdmi_video_standards { > + struct v4l2_dv_timings timings; > + u8 vid_std; > + u8 v_freq; > +}; > + > +static const struct adv748x_hdmi_video_standards > +adv748x_hdmi_video_standards[] = { > + { V4L2_DV_BT_CEA_720X480I59_94, 0x40, 0x00 }, > + { V4L2_DV_BT_CEA_720X576I50, 0x41, 0x01 }, > + { V4L2_DV_BT_CEA_720X480P59_94, 0x4a, 0x00 }, > + { V4L2_DV_BT_CEA_720X576P50, 0x4b, 0x00 }, > + { V4L2_DV_BT_CEA_1280X720P60, 0x53, 0x00 }, > + { V4L2_DV_BT_CEA_1280X720P50, 0x53, 0x01 }, > + { V4L2_DV_BT_CEA_1280X720P30, 0x53, 0x02 }, > + { V4L2_DV_BT_CEA_1280X720P25, 0x53, 0x03 }, > + { V4L2_DV_BT_CEA_1280X720P24, 0x53, 0x04 }, > + { V4L2_DV_BT_CEA_1920X1080I60, 0x54, 0x00 }, > + { V4L2_DV_BT_CEA_1920X1080I50, 0x54, 0x01 }, > + { V4L2_DV_BT_CEA_1920X1080P60, 0x5e, 0x00 }, > + { V4L2_DV_BT_CEA_1920X1080P50, 0x5e, 0x01 }, > + { V4L2_DV_BT_CEA_1920X1080P30, 0x5e, 0x02 }, > + { V4L2_DV_BT_CEA_1920X1080P25, 0x5e, 0x03 }, > + { V4L2_DV_BT_CEA_1920X1080P24, 0x5e, 0x04 }, > + /* SVGA */ > + { V4L2_DV_BT_DMT_800X600P56, 0x80, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P60, 0x81, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P72, 0x82, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P75, 0x83, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P85, 0x84, 0x00 }, > + /* SXGA */ > + { V4L2_DV_BT_DMT_1280X1024P60, 0x85, 0x00 }, > + { V4L2_DV_BT_DMT_1280X1024P75, 0x86, 0x00 }, > + /* VGA */ > + { V4L2_DV_BT_DMT_640X480P60, 0x88, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P72, 0x89, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P75, 0x8a, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P85, 0x8b, 0x00 }, > + /* XGA */ > + { V4L2_DV_BT_DMT_1024X768P60, 0x8c, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P70, 0x8d, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P75, 0x8e, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P85, 0x8f, 0x00 }, > + /* UXGA */ > + { V4L2_DV_BT_DMT_1600X1200P60, 0x96, 0x00 }, > +}; > + > +static void adv748x_hdmi_fill_format(struct adv748x_hdmi *hdmi, > + struct v4l2_mbus_framefmt *fmt) > +{ > + memset(fmt, 0, sizeof(*fmt)); > + > + fmt->code = MEDIA_BUS_FMT_RGB888_1X24; > + fmt->colorspace = V4L2_COLORSPACE_SRGB; > + fmt->field = hdmi->timings.bt.interlaced ? > + V4L2_FIELD_INTERLACED : V4L2_FIELD_NONE; > + > + fmt->width = hdmi->timings.bt.width; > + fmt->height = hdmi->timings.bt.height; > +} > + > +static void adv748x_fill_optional_dv_timings(struct v4l2_dv_timings *timings) > +{ > + v4l2_find_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, > + 250000, NULL, NULL); > +} > + > +static bool adv748x_hdmi_has_signal(struct adv748x_state *state) > +{ > + int val; > + > + /* Check that VERT_FILTER and DE_REGEN is locked */ > + val = hdmi_read(state, ADV748X_HDMI_LW1); > + return (val & ADV748X_HDMI_LW1_VERT_FILTER) && > + (val & ADV748X_HDMI_LW1_DE_REGEN); > +} > + > +static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state) > +{ > + int a, b; > + > + a = hdmi_read(state, ADV748X_HDMI_TMDS_1); > + b = hdmi_read(state, ADV748X_HDMI_TMDS_2); > + if (a < 0 || b < 0) > + return -ENODATA; > + > + /* > + * The High 9 bits store TMDS frequency measurement in MHz s/High/high/ > + * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency > + * measurement in 1/128 MHz > + */ > + return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128; > +} > + > +/* > + * adv748x_hdmi_set_de_timings: Adjust horizontal picture offset through DE > + * > + * HDMI CP uses a Data Enable synchronisation timing reference > + * > + * Vary the leading and trailing edge position of the DE signal output by the CP > + * core. Values are stored as signed-twos-complement in one-pixel-clock units > + * > + * The start and end are shifted equally by the 10-bit shift value. > + */ > +static void adv748x_hdmi_set_de_timings(struct adv748x_state *state, int shift) > +{ > + u8 high, low; > + > + /* POS_HIGH stores bits 8 and 9 of both the start and end */ > + high = ADV748X_CP_DE_POS_HIGH_SET; > + high |= (shift & 0x300) >> 8; > + low = shift & 0xff; > + > + /* The sequence of the writes is important and must be followed */ > + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); > + cp_write(state, ADV748X_CP_DE_POS_END_LOW, low); > + > + high |= (shift & 0x300) >> 6; > + > + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); > + cp_write(state, ADV748X_CP_DE_POS_START_LOW, low); > +} > + > +static int adv748x_hdmi_set_video_timings(struct adv748x_state *state, > + const struct v4l2_dv_timings *timings) > +{ > + const struct adv748x_hdmi_video_standards *stds = > + adv748x_hdmi_video_standards; > + unsigned int i; > + > + for (i = 0; i < ARRAY_SIZE(adv748x_hdmi_video_standards); i++) { > + if (!v4l2_match_dv_timings(timings, &stds[i].timings, 250000, > + false)) > + continue; > + } > + > + if (i >= ARRAY_SIZE(adv748x_hdmi_video_standards)) > + return -EINVAL; > + > + /* > + * When setting cp_vid_std to either 720p, 1080i, or 1080p, the video > + * will get shifted horizontally to the left in active video mode. > + * The de_h_start and de_h_end controls are used to centre the picture > + * correctly > + */ > + switch (stds[i].vid_std) { > + case 0x53: /* 720p */ > + adv748x_hdmi_set_de_timings(state, -40); > + break; > + case 0x54: /* 1080i */ > + case 0x5e: /* 1080p */ > + adv748x_hdmi_set_de_timings(state, -44); > + break; > + default: > + adv748x_hdmi_set_de_timings(state, 0); > + break; > + } > + > + io_write(state, ADV748X_IO_VID_STD, stds[i].vid_std); > + io_clrset(state, ADV748X_IO_DATAPATH, ADV748X_IO_DATAPATH_VFREQ_M, > + stds[i].v_freq << ADV748X_IO_DATAPATH_VFREQ_SHIFT); > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_hdmi_s_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + > + if (!timings) > + return -EINVAL; > + > + if (v4l2_match_dv_timings(&hdmi->timings, timings, 0, false)) > + return 0; > + > + if (!v4l2_valid_dv_timings(timings, &adv748x_hdmi_timings_cap, > + NULL, NULL)) > + return -ERANGE; > + > + adv748x_fill_optional_dv_timings(timings); > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_hdmi_set_video_timings(state, timings); > + if (ret) > + goto error; > + > + hdmi->timings = *timings; > + > + cp_clrset(state, ADV748X_CP_VID_ADJ_2, ADV748X_CP_VID_ADJ_2_INTERLACED, > + timings->bt.interlaced ? > + ADV748X_CP_VID_ADJ_2_INTERLACED : 0); > + > + mutex_unlock(&state->mutex); > + > + return 0; > + > +error: > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + mutex_lock(&state->mutex); Why you need to take the lock here? > + > + *timings = hdmi->timings; > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + struct v4l2_bt_timings *bt = &timings->bt; > + int pixelclock; > + int polarity; > + > + if (!timings) > + return -EINVAL; > + > + memset(timings, 0, sizeof(struct v4l2_dv_timings)); > + > + if (!adv748x_hdmi_has_signal(state)) > + return -ENOLINK; > + > + pixelclock = adv748x_hdmi_read_pixelclock(state); > + if (pixelclock < 0) > + return -ENODATA; > + > + timings->type = V4L2_DV_BT_656_1120; > + > + bt->pixelclock = pixelclock; > + bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) & > + ADV748X_HDMI_F1H1_INTERLACED ? > + V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; > + bt->width = hdmi_read16(state, ADV748X_HDMI_LW1, > + ADV748X_HDMI_LW1_WIDTH_MASK); > + bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1, > + ADV748X_HDMI_F0H1_HEIGHT_MASK); > + bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH, > + ADV748X_HDMI_HFRONT_PORCH_MASK); > + bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH, > + ADV748X_HDMI_HSYNC_WIDTH_MASK); > + bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH, > + ADV748X_HDMI_HBACK_PORCH_MASK); > + bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH, > + ADV748X_HDMI_VFRONT_PORCH_MASK) / 2; > + bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH, > + ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2; > + bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH, > + ADV748X_HDMI_VBACK_PORCH_MASK) / 2; > + Extra newline. > + > + polarity = hdmi_read(state, 0x05); > + bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) | > + (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0); > + > + if (bt->interlaced == V4L2_DV_INTERLACED) { > + bt->height += hdmi_read16(state, 0x0b, 0x1fff); > + bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2; > + bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2; > + bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2; > + } > + > + adv748x_fill_optional_dv_timings(timings); > + > + /* > + * No interrupt handling is implemented yet. > + * There should be an IRQ when a cable is plugged and the new timings > + * should be figured out and stored to state. > + */ > + hdmi->timings = *timings; > + > + return 0; > +} > + > +static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + mutex_lock(&state->mutex); Lock ? :-) > + > + *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL; > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_hdmi_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_txa_power(state, enable); > + if (ret) > + goto done; > + > + if (adv748x_hdmi_has_signal(state)) > + adv_dbg(state, "Detected HDMI signal\n"); > + else > + adv_dbg(state, "Couldn't detect HDMI video signal\n"); > + > +done: > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_hdmi_g_pixelaspect(struct v4l2_subdev *sd, > + struct v4l2_fract *aspect) > +{ > + aspect->numerator = 1; > + aspect->denominator = 1; > + > + return 0; > +} > + > +static const struct v4l2_subdev_video_ops adv748x_video_ops_hdmi = { > + .s_dv_timings = adv748x_hdmi_s_dv_timings, > + .g_dv_timings = adv748x_hdmi_g_dv_timings, > + .query_dv_timings = adv748x_hdmi_query_dv_timings, > + .g_input_status = adv748x_hdmi_g_input_status, > + .s_stream = adv748x_hdmi_s_stream, > + .g_pixelaspect = adv748x_hdmi_g_pixelaspect, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + */ > + > +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) > +{ > + struct v4l2_subdev *tx; > + struct v4l2_dv_timings timings; > + struct v4l2_bt_timings *bt = &timings.bt; > + unsigned int fps; > + > + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); > + if (!tx) > + return -ENOLINK; > + > + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); > + > + fps = DIV_ROUND_CLOSEST(bt->pixelclock, > + V4L2_DV_BT_FRAME_WIDTH(bt) * > + V4L2_DV_BT_FRAME_HEIGHT(bt)); > + > + return adv748x_csi2_set_pixelrate(tx, bt->width * bt->height * fps); > +} > + > +static int adv748x_hdmi_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->index != 0) > + return -EINVAL; > + > + code->code = MEDIA_BUS_FMT_RGB888_1X24; > + > + return 0; > +} > + > +static int adv748x_hdmi_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct v4l2_mbus_framefmt *mbusformat; > + > + if (sdformat->pad != ADV748X_HDMI_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + sdformat->format = *mbusformat; > + } else { > + adv748x_hdmi_fill_format(hdmi, &sdformat->format); > + adv748x_hdmi_set_pixelrate(hdmi); > + } > + > + return 0; > +} > + > +static int adv748x_hdmi_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct v4l2_mbus_framefmt *mbusformat; > + > + if (sdformat->pad != ADV748X_HDMI_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) > + return adv748x_hdmi_get_format(sd, cfg, sdformat); > + > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + *mbusformat = sdformat->format; Same comment as for adv748x_afe_set_format(). > + > + return 0; > +} > + > +static bool adv748x_hdmi_check_dv_timings(const struct v4l2_dv_timings *timings, > + void *hdl) > +{ > + const struct adv748x_hdmi_video_standards *stds = > + adv748x_hdmi_video_standards; > + unsigned int i; > + > + for (i = 0; stds[i].timings.bt.width; i++) > + if (v4l2_match_dv_timings(timings, &stds[i].timings, 0, false)) > + return true; > + > + return false; > +} > + > +static int adv748x_hdmi_enum_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_enum_dv_timings *timings) > +{ > + return v4l2_enum_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, > + adv748x_hdmi_check_dv_timings, NULL); > +} > + > +static int adv748x_hdmi_dv_timings_cap(struct v4l2_subdev *sd, > + struct v4l2_dv_timings_cap *cap) > +{ > + *cap = adv748x_hdmi_timings_cap; > + return 0; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_pad_ops_hdmi = { > + .enum_mbus_code = adv748x_hdmi_enum_mbus_code, > + .set_fmt = adv748x_hdmi_set_format, > + .get_fmt = adv748x_hdmi_get_format, > + .dv_timings_cap = adv748x_hdmi_dv_timings_cap, > + .enum_dv_timings = adv748x_hdmi_enum_dv_timings, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_ops_hdmi = { > + .video = &adv748x_video_ops_hdmi, > + .pad = &adv748x_pad_ops_hdmi, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Controls > + */ > + > +static const char * const hdmi_ctrl_patgen_menu[] = { > + "Disabled", > + "Plain Blue", > + "Color Bars", > + "Ramp Grey", > + "Ramp Blue", > + "Ramp Red", > + "Checkered" > +}; > + > +static int adv748x_hdmi_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct adv748x_hdmi *hdmi = adv748x_ctrl_to_hdmi(ctrl); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + u8 pattern; > + > + /* Enable video adjustment first */ > + ret = cp_clrset(state, ADV748X_CP_VID_ADJ, > + ADV748X_CP_VID_ADJ_ENABLE, > + ADV748X_CP_VID_ADJ_ENABLE); > + if (ret < 0) > + return ret; > + > + switch (ctrl->id) { > + case V4L2_CID_BRIGHTNESS: > + ret = cp_write(state, ADV748X_CP_BRI, ctrl->val); > + break; > + case V4L2_CID_HUE: > + ret = cp_write(state, ADV748X_CP_HUE, ctrl->val); > + break; > + case V4L2_CID_CONTRAST: > + ret = cp_write(state, ADV748X_CP_CON, ctrl->val); > + break; > + case V4L2_CID_SATURATION: > + ret = cp_write(state, ADV748X_CP_SAT, ctrl->val); > + break; > + case V4L2_CID_TEST_PATTERN: > + pattern = ctrl->val; > + > + /* Pattern is 0-indexed. Ctrl Menu is 1-indexed */ > + if (pattern) { > + pattern--; > + pattern |= ADV748X_CP_PAT_GEN_EN; > + } > + > + ret = cp_write(state, ADV748X_CP_PAT_GEN, pattern); > + > + break; > + default: > + return -EINVAL; > + } > + > + return ret; > +} > + > +static const struct v4l2_ctrl_ops adv748x_hdmi_ctrl_ops = { > + .s_ctrl = adv748x_hdmi_s_ctrl, > +}; > + > +static int adv748x_hdmi_init_controls(struct adv748x_hdmi *hdmi) > +{ > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + v4l2_ctrl_handler_init(&hdmi->ctrl_hdl, 5); > + > + /* Use our mutex for the controls */ > + hdmi->ctrl_hdl.lock = &state->mutex; > + > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_BRIGHTNESS, ADV748X_CP_BRI_MIN, > + ADV748X_CP_BRI_MAX, 1, ADV748X_CP_BRI_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_CONTRAST, ADV748X_CP_CON_MIN, > + ADV748X_CP_CON_MAX, 1, ADV748X_CP_CON_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_SATURATION, ADV748X_CP_SAT_MIN, > + ADV748X_CP_SAT_MAX, 1, ADV748X_CP_SAT_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_HUE, ADV748X_CP_HUE_MIN, > + ADV748X_CP_HUE_MAX, 1, ADV748X_CP_HUE_DEF); > + > + v4l2_ctrl_new_std_menu_items(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(hdmi_ctrl_patgen_menu) - 1, > + 0, 0, hdmi_ctrl_patgen_menu); > + > + hdmi->sd.ctrl_handler = &hdmi->ctrl_hdl; > + if (hdmi->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); > + return hdmi->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&hdmi->ctrl_hdl); > +} > + > +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi) > +{ > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + static const struct v4l2_dv_timings cea720x480 = > + V4L2_DV_BT_CEA_720X480I59_94; > + int ret; > + > + hdmi->timings = cea720x480; > + > + adv748x_subdev_init(&hdmi->sd, state, &adv748x_ops_hdmi, > + MEDIA_ENT_F_IO_DTV, "hdmi"); > + > + hdmi->pads[ADV748X_HDMI_SINK].flags = MEDIA_PAD_FL_SINK; > + hdmi->pads[ADV748X_HDMI_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&hdmi->sd.entity, > + ADV748X_HDMI_NR_PADS, hdmi->pads); > + if (ret) > + return ret; > + > + ret = adv748x_hdmi_init_controls(hdmi); > + if (ret) > + goto err_free_media; > + > + return 0; > + > +err_free_media: > + media_entity_cleanup(&hdmi->sd.entity); > + > + return ret; > +} > + > +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi) > +{ > + v4l2_device_unregister_subdev(&hdmi->sd); > + media_entity_cleanup(&hdmi->sd.entity); > + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x.h b/drivers/media/i2c/adv748x/adv748x.h > new file mode 100644 > index 000000000000..2f36e5052f08 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x.h > @@ -0,0 +1,415 @@ > +/* > + * Driver for Analog Devices ADV748X video decoder and HDMI receiver > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + * > + * Authors: > + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> > + * Niklas Söderlund <niklas.soderlund@ragnatech.se> > + * Kieran Bingham <kieran.bingham@ideasonboard.com> > + * > + * The ADV748x range of receivers have the following configurations: > + * > + * Analog HDMI MHL 4-Lane 1-Lane > + * In In CSI CSI > + * ADV7480 X X X > + * ADV7481 X X X X X > + * ADV7482 X X X X > + */ > + > +#include <linux/i2c.h> > + > +#ifndef _ADV748X_H_ > +#define _ADV748X_H_ > + > +/* I2C slave addresses */ > +#define ADV748X_I2C_IO 0x70 /* IO Map */ > +#define ADV748X_I2C_DPLL 0x26 /* DPLL Map */ > +#define ADV748X_I2C_CP 0x22 /* CP Map */ > +#define ADV748X_I2C_HDMI 0x34 /* HDMI Map */ > +#define ADV748X_I2C_EDID 0x36 /* EDID Map */ > +#define ADV748X_I2C_REPEATER 0x32 /* HDMI RX Repeater Map */ > +#define ADV748X_I2C_INFOFRAME 0x31 /* HDMI RX InfoFrame Map */ > +#define ADV748X_I2C_CEC 0x41 /* CEC Map */ > +#define ADV748X_I2C_SDP 0x79 /* SDP Map */ > +#define ADV748X_I2C_TXB 0x48 /* CSI-TXB Map */ > +#define ADV748X_I2C_TXA 0x4a /* CSI-TXA Map */ > + > +enum adv748x_page { > + ADV748X_PAGE_IO, > + ADV748X_PAGE_DPLL, > + ADV748X_PAGE_CP, > + ADV748X_PAGE_HDMI, > + ADV748X_PAGE_EDID, > + ADV748X_PAGE_REPEATER, > + ADV748X_PAGE_INFOFRAME, > + ADV748X_PAGE_CEC, > + ADV748X_PAGE_SDP, > + ADV748X_PAGE_TXB, > + ADV748X_PAGE_TXA, > + ADV748X_PAGE_MAX, > + > + /* Fake pages for register sequences */ > + ADV748X_PAGE_WAIT, /* Wait x msec */ > + ADV748X_PAGE_EOR, /* End Mark */ > +}; > + > +/** > + * enum adv748x_ports - Device tree port number definitions > + * > + * The ADV748X ports define the mapping between subdevices > + * and the device tree specification > + */ > +enum adv748x_ports { > + ADV748X_PORT_AIN0 = 0, > + ADV748X_PORT_AIN1 = 1, > + ADV748X_PORT_AIN2 = 2, > + ADV748X_PORT_AIN3 = 3, > + ADV748X_PORT_AIN4 = 4, > + ADV748X_PORT_AIN5 = 5, > + ADV748X_PORT_AIN6 = 6, > + ADV748X_PORT_AIN7 = 7, > + ADV748X_PORT_HDMI = 8, > + ADV748X_PORT_TTL = 9, > + ADV748X_PORT_TXA = 10, > + ADV748X_PORT_TXB = 11, > + ADV748X_PORT_MAX = 12, > +}; > + > +enum adv748x_csi2_pads { > + ADV748X_CSI2_SINK, > + ADV748X_CSI2_SOURCE, > + ADV748X_CSI2_NR_PADS, > +}; > + > +/* CSI2 transmitters can have 2 internal connections, HDMI/AFE */ > +#define ADV748X_CSI2_MAX_SUBDEVS 2 > + > +struct adv748x_csi2 { > + struct adv748x_state *state; > + struct v4l2_mbus_framefmt format; > + unsigned int page; > + > + struct media_pad pads[ADV748X_CSI2_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > +}; > + > +#define notifier_to_csi2(n) container_of(n, struct adv748x_csi2, notifier) > +#define adv748x_sd_to_csi2(sd) container_of(sd, struct adv748x_csi2, sd) > + > +enum adv748x_hdmi_pads { > + ADV748X_HDMI_SINK, > + ADV748X_HDMI_SOURCE, > + ADV748X_HDMI_NR_PADS, > +}; > + > +struct adv748x_hdmi { > + struct media_pad pads[ADV748X_HDMI_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > + struct v4l2_mbus_framefmt format; > + > + struct v4l2_dv_timings timings; > +}; > + > +#define adv748x_ctrl_to_hdmi(ctrl) \ > + container_of(ctrl->handler, struct adv748x_hdmi, ctrl_hdl) > +#define adv748x_sd_to_hdmi(sd) container_of(sd, struct adv748x_hdmi, sd) > + > +enum adv748x_afe_pads { > + ADV748X_AFE_SINK_AIN0, > + ADV748X_AFE_SINK_AIN1, > + ADV748X_AFE_SINK_AIN2, > + ADV748X_AFE_SINK_AIN3, > + ADV748X_AFE_SINK_AIN4, > + ADV748X_AFE_SINK_AIN5, > + ADV748X_AFE_SINK_AIN6, > + ADV748X_AFE_SINK_AIN7, > + ADV748X_AFE_SOURCE, > + ADV748X_AFE_NR_PADS, > +}; > + > +struct adv748x_afe { > + struct media_pad pads[ADV748X_AFE_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > + struct v4l2_mbus_framefmt format; > + > + bool streaming; > + v4l2_std_id curr_norm; > + unsigned int input; > +}; > + > +#define adv748x_ctrl_to_afe(ctrl) \ > + container_of(ctrl->handler, struct adv748x_afe, ctrl_hdl) > +#define adv748x_sd_to_afe(sd) container_of(sd, struct adv748x_afe, sd) > + > +/** > + * struct adv748x_state - State of ADV748X > + * @dev: (OF) device > + * @client: I2C client > + * @mutex: protect global state > + * > + * @endpoints: parsed device node endpoints for each port > + * > + * @i2c_addresses I2C Page addresses > + * @i2c_clients I2C clients for the page accesses > + * @regmap regmap configuration pages. > + * > + * @hdmi: state of HDMI receiver context > + * @afe: state of AFE receiver context > + * @txa: state of TXA transmitter context > + * @txb: state of TXB transmitter context > + */ > +struct adv748x_state { > + struct device *dev; > + struct i2c_client *client; > + struct mutex mutex; > + > + struct device_node *endpoints[ADV748X_PORT_MAX]; > + > + struct i2c_client *i2c_clients[ADV748X_PAGE_MAX]; > + struct regmap *regmap[ADV748X_PAGE_MAX]; > + > + struct adv748x_hdmi hdmi; > + struct adv748x_afe afe; > + struct adv748x_csi2 txa; > + struct adv748x_csi2 txb; > +}; > + > +#define adv748x_hdmi_to_state(h) container_of(h, struct adv748x_state, hdmi) > +#define adv748x_afe_to_state(a) container_of(a, struct adv748x_state, afe) > + > +#define adv_err(a, fmt, arg...) dev_err(a->dev, fmt, ##arg) > +#define adv_info(a, fmt, arg...) dev_info(a->dev, fmt, ##arg) > +#define adv_dbg(a, fmt, arg...) dev_dbg(a->dev, fmt, ##arg) > + > +/* Register Mappings */ > + > +/* IO Map */ > +#define ADV748X_IO_PD 0x00 /* power down controls */ > +#define ADV748X_IO_PD_RX_EN BIT(6) > + > +#define ADV748X_IO_REG_04 0x04 > +#define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */ > + > +#define ADV748X_IO_DATAPATH 0x03 /* datapath cntrl */ > +#define ADV748X_IO_DATAPATH_VFREQ_M 0x70 > +#define ADV748X_IO_DATAPATH_VFREQ_SHIFT 4 > + > +#define ADV748X_IO_VID_STD 0x05 > + > +#define ADV748X_IO_10 0x10 /* io_reg_10 */ > +#define ADV748X_IO_10_CSI4_EN BIT(7) > +#define ADV748X_IO_10_CSI1_EN BIT(6) > +#define ADV748X_IO_10_PIX_OUT_EN BIT(5) > + > +#define ADV748X_IO_CHIP_REV_ID_1 0xdf > +#define ADV748X_IO_CHIP_REV_ID_2 0xe0 > + > +#define ADV748X_IO_SLAVE_ADDR_BASE 0xf2 > + > +/* HDMI RX Map */ > +#define ADV748X_HDMI_LW1 0x07 /* line width_1 */ > +#define ADV748X_HDMI_LW1_VERT_FILTER BIT(7) > +#define ADV748X_HDMI_LW1_DE_REGEN BIT(5) > +#define ADV748X_HDMI_LW1_WIDTH_MASK 0x1fff > + > +#define ADV748X_HDMI_F0H1 0x09 /* field0 height_1 */ > +#define ADV748X_HDMI_F0H1_HEIGHT_MASK 0x1fff > + > +#define ADV748X_HDMI_F1H1 0x0b /* field1 height_1 */ > +#define ADV748X_HDMI_F1H1_INTERLACED BIT(5) > + > +#define ADV748X_HDMI_HFRONT_PORCH 0x20 /* hsync_front_porch_1 */ > +#define ADV748X_HDMI_HFRONT_PORCH_MASK 0x1fff > + > +#define ADV748X_HDMI_HSYNC_WIDTH 0x22 /* hsync_pulse_width_1 */ > +#define ADV748X_HDMI_HSYNC_WIDTH_MASK 0x1fff > + > +#define ADV748X_HDMI_HBACK_PORCH 0x24 /* hsync_back_porch_1 */ > +#define ADV748X_HDMI_HBACK_PORCH_MASK 0x1fff > + > +#define ADV748X_HDMI_VFRONT_PORCH 0x2a /* field0_vs_front_porch_1 */ > +#define ADV748X_HDMI_VFRONT_PORCH_MASK 0x3fff > + > +#define ADV748X_HDMI_VSYNC_WIDTH 0x2e /* field0_vs_pulse_width_1 */ > +#define ADV748X_HDMI_VSYNC_WIDTH_MASK 0x3fff > + > +#define ADV748X_HDMI_VBACK_PORCH 0x32 /* field0_vs_back_porch_1 */ > +#define ADV748X_HDMI_VBACK_PORCH_MASK 0x3fff > + > +#define ADV748X_HDMI_TMDS_1 0x51 /* hdmi_reg_51 */ > +#define ADV748X_HDMI_TMDS_2 0x52 /* hdmi_reg_52 */ > + > +/* SDP Main Map */ > +#define ADV748X_SDP_INSEL 0x00 /* user_map_rw_reg_00 */ > + > +#define ADV748X_SDP_VID_SEL 0x02 /* user_map_rw_reg_02 */ > +#define ADV748X_SDP_VID_SEL_MASK 0xf0 > +#define ADV748X_SDP_VID_SEL_SHIFT 4 > + > +/* Contrast - Unsigned*/ > +#define ADV748X_SDP_CON 0x08 /* user_map_rw_reg_08 */ > +#define ADV748X_SDP_CON_MIN 0 > +#define ADV748X_SDP_CON_DEF 128 > +#define ADV748X_SDP_CON_MAX 255 > + > +/* Brightness - Signed */ > +#define ADV748X_SDP_BRI 0x0a /* user_map_rw_reg_0a */ > +#define ADV748X_SDP_BRI_MIN -128 > +#define ADV748X_SDP_BRI_DEF 0 > +#define ADV748X_SDP_BRI_MAX 127 > + > +/* Hue - Signed, inverted*/ > +#define ADV748X_SDP_HUE 0x0b /* user_map_rw_reg_0b */ > +#define ADV748X_SDP_HUE_MIN -127 > +#define ADV748X_SDP_HUE_DEF 0 > +#define ADV748X_SDP_HUE_MAX 128 > + > +/* Test Patterns / Default Values */ > +#define ADV748X_SDP_DEF 0x0c /* user_map_rw_reg_0c */ > +#define ADV748X_SDP_DEF_VAL_EN BIT(0) /* Force free run mode */ > +#define ADV748X_SDP_DEF_VAL_AUTO_EN BIT(1) /* Free run when no signal */ > + > +#define ADV748X_SDP_MAP_SEL 0x0e /* user_map_rw_reg_0e */ > +#define ADV748X_SDP_MAP_SEL_RO_MAIN 1 > + > +/* Free run pattern select */ > +#define ADV748X_SDP_FRP 0x14 > +#define ADV748X_SDP_FRP_MASK GENMASK(3, 1) > + > +/* Saturation */ > +#define ADV748X_SDP_SD_SAT_U 0xe3 /* user_map_rw_reg_e3 */ > +#define ADV748X_SDP_SD_SAT_V 0xe4 /* user_map_rw_reg_e4 */ > +#define ADV748X_SDP_SAT_MIN 0 > +#define ADV748X_SDP_SAT_DEF 128 > +#define ADV748X_SDP_SAT_MAX 255 > + > +/* SDP RO Main Map */ > +#define ADV748X_SDP_RO_10 0x10 > +#define ADV748X_SDP_RO_10_IN_LOCK BIT(0) > + > +/* CP Map */ > +#define ADV748X_CP_PAT_GEN 0x37 /* int_pat_gen_1 */ > +#define ADV748X_CP_PAT_GEN_EN BIT(7) > + > +/* Contrast Control - Unsigned */ > +#define ADV748X_CP_CON 0x3a /* contrast_cntrl */ > +#define ADV748X_CP_CON_MIN 0 /* Minimum contrast */ > +#define ADV748X_CP_CON_DEF 128 /* Default */ > +#define ADV748X_CP_CON_MAX 255 /* Maximum contrast */ > + > +/* Saturation Control - Unsigned */ > +#define ADV748X_CP_SAT 0x3b /* saturation_cntrl */ > +#define ADV748X_CP_SAT_MIN 0 /* Minimum saturation */ > +#define ADV748X_CP_SAT_DEF 128 /* Default */ > +#define ADV748X_CP_SAT_MAX 255 /* Maximum saturation */ > + > +/* Brightness Control - Signed */ > +#define ADV748X_CP_BRI 0x3c /* brightness_cntrl */ > +#define ADV748X_CP_BRI_MIN -128 /* Luma is -512d */ > +#define ADV748X_CP_BRI_DEF 0 /* Luma is 0 */ > +#define ADV748X_CP_BRI_MAX 127 /* Luma is 508d */ > + > +/* Hue Control */ > +#define ADV748X_CP_HUE 0x3d /* hue_cntrl */ > +#define ADV748X_CP_HUE_MIN 0 /* -90 degree */ > +#define ADV748X_CP_HUE_DEF 0 /* -90 degree */ > +#define ADV748X_CP_HUE_MAX 255 /* +90 degree */ > + > +#define ADV748X_CP_VID_ADJ 0x3e /* vid_adj_0 */ > +#define ADV748X_CP_VID_ADJ_ENABLE BIT(7) /* Enable colour controls */ > + > +#define ADV748X_CP_DE_POS_HIGH 0x8b /* de_pos_adj_6 */ > +#define ADV748X_CP_DE_POS_HIGH_SET BIT(6) > +#define ADV748X_CP_DE_POS_END_LOW 0x8c /* de_pos_adj_7 */ > +#define ADV748X_CP_DE_POS_START_LOW 0x8d /* de_pos_adj_8 */ > + > +#define ADV748X_CP_VID_ADJ_2 0x91 > +#define ADV748X_CP_VID_ADJ_2_INTERLACED BIT(6) > +#define ADV748X_CP_VID_ADJ_2_INTERLACED_3D BIT(4) > + > +#define ADV748X_CP_CLMP_POS 0xc9 /* clmp_pos_cntrl_4 */ > +#define ADV748X_CP_CLMP_POS_DIS_AUTO BIT(0) /* dis_auto_param_buff */ > + > +/* CSI : TXA/TXB Maps */ > +#define ADV748X_CSI_VC_REF 0x0d /* csi_tx_top_reg_0d */ > +#define ADV748X_CSI_VC_REF_SHIFT 6 > + > +#define ADV748X_CSI_FS_AS_LS 0x1e /* csi_tx_top_reg_1e */ > +#define ADV748X_CSI_FS_AS_LS_UNKNOWN BIT(6) /* Undocumented bit */ > + > +/* Register handling */ > + > +int adv748x_read(struct adv748x_state *state, u8 addr, u8 reg); > +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value); > +int adv748x_write_block(struct adv748x_state *state, int client_page, > + unsigned int init_reg, const void *val, > + size_t val_len); > + > +#define io_read(s, r) adv748x_read(s, ADV748X_PAGE_IO, r) > +#define io_write(s, r, v) adv748x_write(s, ADV748X_PAGE_IO, r, v) > +#define io_clrset(s, r, m, v) io_write(s, r, (io_read(s, r) & ~m) | v) > + > +#define hdmi_read(s, r) adv748x_read(s, ADV748X_PAGE_HDMI, r) > +#define hdmi_read16(s, r, m) (((hdmi_read(s, r) << 8) | hdmi_read(s, r+1)) & m) > +#define hdmi_write(s, r, v) adv748x_write(s, ADV748X_PAGE_HDMI, r, v) > +#define hdmi_clrset(s, r, m, v) hdmi_write(s, r, (hdmi_read(s, r) & ~m) | v) > + > +#define sdp_read(s, r) adv748x_read(s, ADV748X_PAGE_SDP, r) > +#define sdp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_SDP, r, v) > +#define sdp_clrset(s, r, m, v) sdp_write(s, r, (sdp_read(s, r) & ~m) | v) > + > +#define cp_read(s, r) adv748x_read(s, ADV748X_PAGE_CP, r) > +#define cp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_CP, r, v) > +#define cp_clrset(s, r, m, v) cp_write(s, r, (cp_read(s, r) & ~m) | v) > + > +#define txa_read(s, r) adv748x_read(s, ADV748X_PAGE_TXA, r) > +#define txa_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXA, r, v) > +#define txa_clrset(s, r, m, v) txa_write(s, r, (txa_read(s, r) & ~m) | v) > + > +#define txb_read(s, r) adv748x_read(s, ADV748X_PAGE_TXB, r) > +#define txb_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXB, r, v) > +#define txb_clrset(s, r, m, v) txb_write(s, r, (txb_read(s, r) & ~m) | v) > + > +#define tx_read(t, r) adv748x_read(t->state, t->page, r) > +#define tx_write(t, r, v) adv748x_write(t->state, t->page, r, v) > +#define tx_clrset(t, r, m, v) tx_write(t, r, (tx_read(t, r) & ~m) | v) > + > +static inline struct v4l2_subdev *adv748x_get_remote_sd(struct media_pad *pad) > +{ > + pad = media_entity_remote_pad(pad); > + if (!pad) > + return NULL; > + > + return media_entity_to_v4l2_subdev(pad->entity); > +} > + > +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, > + const struct v4l2_subdev_ops *ops, u32 function, > + const char *ident); > + > +int adv748x_register_subdevs(struct adv748x_state *state, > + struct v4l2_device *v4l2_dev); > + > +int adv748x_txa_power(struct adv748x_state *state, bool on); > +int adv748x_txb_power(struct adv748x_state *state, bool on); > + > +int adv748x_afe_init(struct adv748x_afe *afe); > +void adv748x_afe_cleanup(struct adv748x_afe *afe); > + > +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx); > +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx); > +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate); > + > +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi); > +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi); > + > +#endif /* _ADV748X_H_ */ > -- > git-series 0.9.1
Hi Kieran, On Tue, Jun 13, 2017 at 2:35 AM, Kieran Bingham <kbingham@kernel.org> wrote: > From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > Provide support for the ADV7481 and ADV7482. > > The driver is modelled with 4 subdevices to allow simultaneous streaming > from the AFE (Analog front end) and HDMI inputs though two CSI TX > entities. > > The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked > to the TXB CSI bus. > > The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, > and an earlier rework by Niklas Söderlund. > > Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c > +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) > +{ > + struct v4l2_subdev *tx; > + struct v4l2_dv_timings timings; > + struct v4l2_bt_timings *bt = &timings.bt; > + unsigned int fps; > + > + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); > + if (!tx) > + return -ENOLINK; > + > + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); > + > + fps = DIV_ROUND_CLOSEST(bt->pixelclock, > + V4L2_DV_BT_FRAME_WIDTH(bt) * > + V4L2_DV_BT_FRAME_HEIGHT(bt)); On arm32: drivers/built-in.o: In function `adv748x_hdmi_set_pixelrate': :(.text+0x1b8b1c): undefined reference to `__aeabi_uldivmod' v4l2_bt_timings.pixelclock is u64, so you should use DIV_ROUND_CLOSEST_ULL() instead. Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
On 13/06/17 10:24, Geert Uytterhoeven wrote: > Hi Kieran, > > On Tue, Jun 13, 2017 at 2:35 AM, Kieran Bingham <kbingham@kernel.org> wrote: >> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> >> Provide support for the ADV7481 and ADV7482. >> >> The driver is modelled with 4 subdevices to allow simultaneous streaming >> from the AFE (Analog front end) and HDMI inputs though two CSI TX >> entities. >> >> The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked >> to the TXB CSI bus. >> >> The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, >> and an earlier rework by Niklas Söderlund. >> >> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c > >> +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) >> +{ >> + struct v4l2_subdev *tx; >> + struct v4l2_dv_timings timings; >> + struct v4l2_bt_timings *bt = &timings.bt; >> + unsigned int fps; >> + >> + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); >> + if (!tx) >> + return -ENOLINK; >> + >> + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); >> + >> + fps = DIV_ROUND_CLOSEST(bt->pixelclock, >> + V4L2_DV_BT_FRAME_WIDTH(bt) * >> + V4L2_DV_BT_FRAME_HEIGHT(bt)); > > On arm32: > > drivers/built-in.o: In function `adv748x_hdmi_set_pixelrate': > :(.text+0x1b8b1c): undefined reference to `__aeabi_uldivmod' > > v4l2_bt_timings.pixelclock is u64, so you should use DIV_ROUND_CLOSEST_ULL() > instead. Aha, thanks. /me ponders why I didn't get spammed from the bot-builders about this? Fix applied locally ready for v5. Would you like the remote updated for renesas-drivers or will you patch locally? -- Kieran > Gr{oetje,eeting}s, > > Geert > > -- > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org > > In personal conversations with technical people, I call myself a hacker. But > when I'm talking to journalists I just say "programmer" or something like that. > -- Linus Torvalds >
Hi Kieran, On Tue, Jun 13, 2017 at 11:32 AM, Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> wrote: > On 13/06/17 10:24, Geert Uytterhoeven wrote: >> On Tue, Jun 13, 2017 at 2:35 AM, Kieran Bingham <kbingham@kernel.org> wrote: >>> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >>> >>> Provide support for the ADV7481 and ADV7482. >>> >>> The driver is modelled with 4 subdevices to allow simultaneous streaming >>> from the AFE (Analog front end) and HDMI inputs though two CSI TX >>> entities. >>> >>> The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked >>> to the TXB CSI bus. >>> >>> The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, >>> and an earlier rework by Niklas Söderlund. >>> >>> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> >>> --- /dev/null >>> +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c >> >>> +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) >>> +{ >>> + struct v4l2_subdev *tx; >>> + struct v4l2_dv_timings timings; >>> + struct v4l2_bt_timings *bt = &timings.bt; >>> + unsigned int fps; >>> + >>> + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); >>> + if (!tx) >>> + return -ENOLINK; >>> + >>> + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); >>> + >>> + fps = DIV_ROUND_CLOSEST(bt->pixelclock, >>> + V4L2_DV_BT_FRAME_WIDTH(bt) * >>> + V4L2_DV_BT_FRAME_HEIGHT(bt)); >> >> On arm32: >> >> drivers/built-in.o: In function `adv748x_hdmi_set_pixelrate': >> :(.text+0x1b8b1c): undefined reference to `__aeabi_uldivmod' >> >> v4l2_bt_timings.pixelclock is u64, so you should use DIV_ROUND_CLOSEST_ULL() >> instead. > > Aha, thanks. > > /me ponders why I didn't get spammed from the bot-builders about this? -EBUSY? > Fix applied locally ready for v5. > > Would you like the remote updated for renesas-drivers or will you patch locally? I'll patch it locally just to avoid receiving more spam from the builders soon (we don't use adv748x on arm32 boards). Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Hi Niklas On 13/06/17 08:33, Niklas Söderlund wrote: > Hi Kieran, > > Thanks for your patch, and great work! Thanks for taking a look. > On 2017-06-13 01:35:07 +0100, Kieran Bingham wrote: >> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> >> Provide support for the ADV7481 and ADV7482. >> >> The driver is modelled with 4 subdevices to allow simultaneous streaming >> from the AFE (Analog front end) and HDMI inputs though two CSI TX >> entities. >> >> The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked >> to the TXB CSI bus. >> >> The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, >> and an earlier rework by Niklas Söderlund. >> >> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> <snip> >> +static int adv748x_afe_get_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + /* The format of the analog sink pads is nonsensical */ >> + if (sdformat->pad != ADV748X_AFE_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + sdformat->format = *mbusformat; >> + } else { >> + adv748x_afe_fill_format(afe, &sdformat->format); >> + adv748x_afe_set_pixelrate(afe); >> + } >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + /* The format of the analog sink pads is nonsensical */ >> + if (sdformat->pad != ADV748X_AFE_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) >> + return adv748x_afe_get_format(sd, cfg, sdformat); >> + >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + *mbusformat = sdformat->format; > > Hum, for the V4L2_SUBDEV_FORMAT_TRY case will this not accept any format > provided to the function? Should you not limit this to the device > capabilities before assigning it to mbusformat ? Hrmmm maybe it got too late last night :) I was trying to remove the effect of the active setting on the TRY format, and I've gone too far :) > >> + >> + return 0; >> +} <snip> >> + >> +static int adv748x_setup_links(struct adv748x_state *state) >> +{ >> + int ret; >> + int enabled = MEDIA_LNK_FL_ENABLED; >> + >> +/* >> + * HACK/Workaround: >> + * >> + * Currently non-immutable link resets go through the RVin >> + * driver, and cause the links to fail, due to not being part of RVIN. >> + * As a temporary workaround until the RVIN driver knows better than to parse >> + * links that do not belong to it, use static immutable links for our internal >> + * media paths. >> + */ > > The problem is a bigger then just the VIN ignoring the links not > belonging to it self I think. The ADV7482 driver must have a link > notification handler to deal with the links that belong to it. > > Else if all links of the media device is reset there is no way to setup > the links between the different ADV7482 subdevices, or am I missing > something? Ahhh -- this function shouldn't even be in here ! It's not meant to be used - Links are now created in adv748x_csi2_register_link() so now I'm concerned why I didn't get an unused function compiler warning :) However - your point still stands. > >> +#define ADV748x_DEV_STATIC_LINKS >> +#ifdef ADV748x_DEV_STATIC_LINKS >> + enabled |= MEDIA_LNK_FL_IMMUTABLE; >> +#endif >> + >> + /* TXA - Default link is with HDMI */ >> + ret = media_create_pad_link(&state->hdmi.sd.entity, 1, >> + &state->txa.sd.entity, 0, enabled); >> + if (ret) { >> + adv_err(state, "Failed to create HDMI-TXA pad link"); >> + return ret; >> + } >> + >> +#ifndef ADV748x_DEV_STATIC_LINKS >> + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, >> + &state->txa.sd.entity, 0, 0); >> + if (ret) { >> + adv_err(state, "Failed to create AFE-TXA pad link"); >> + return ret; >> + } >> +#endif >> + >> + /* TXB - Can only output from the AFE */ >> + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, >> + &state->txb.sd.entity, 0, enabled); >> + if (ret) { >> + adv_err(state, "Failed to create AFE-TXB pad link"); >> + return ret; >> + } >> + >> + return 0; >> +} >> + >> +int adv748x_register_subdevs(struct adv748x_state *state, >> + struct v4l2_device *v4l2_dev) And that's why I didn't get a function unused warning from the compiler. adv748x_setup_links() is called by adv748x_register_subdevs() which is not static, but is never used. I've just removed these two functions. - the new linking mechanism is handled during the registration of the CSI2 entitiy. However your consideration about links resetting is still valid - as I have only been testing with immutable links which will have prevented me from seeing the issues. >> +{ >> + int ret; >> + >> + ret = v4l2_device_register_subdev(v4l2_dev, &state->hdmi.sd); >> + if (ret < 0) >> + return ret; >> + >> + ret = v4l2_device_register_subdev(v4l2_dev, &state->afe.sd); >> + if (ret < 0) >> + goto err_unregister_hdmi; >> + >> + ret = adv748x_setup_links(state); >> + if (ret < 0) >> + goto err_unregister_afe; >> + >> + return 0; >> + >> +err_unregister_afe: >> + v4l2_device_unregister_subdev(&state->afe.sd); >> +err_unregister_hdmi: >> + v4l2_device_unregister_subdev(&state->hdmi.sd); >> + >> + return ret; >> +} >> + <snip> >> +static int adv748x_csi2_get_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct adv748x_state *state = tx->state; >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, >> + sdformat->which); >> + if (!mbusformat) >> + return -EINVAL; >> + >> + mutex_lock(&state->mutex); > > Why do you need to take the lock here? I'm not saying it's wrong just > curious :-) > I think the get/set formats are both userspace API's that 'could' be accessed in parallel which read/modify the same context ... >> + >> + sdformat->format = *mbusformat; >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + >> +static int adv748x_csi2_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct adv748x_state *state = tx->state; >> + struct v4l2_mbus_framefmt *mbusformat; >> + int ret = 0; >> + >> + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, >> + sdformat->which); >> + if (!mbusformat) >> + return -EINVAL; >> + >> + mutex_lock(&state->mutex); > > Also why you need to lock here? As above... if this is extraneous I'll remove it. >> + >> +static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state) >> +{ >> + int a, b; >> + >> + a = hdmi_read(state, ADV748X_HDMI_TMDS_1); >> + b = hdmi_read(state, ADV748X_HDMI_TMDS_2); >> + if (a < 0 || b < 0) >> + return -ENODATA; >> + >> + /* >> + * The High 9 bits store TMDS frequency measurement in MHz > > s/High/high/ > fixed. >> + * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency >> + * measurement in 1/128 MHz >> + */ >> + return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128; >> +} >> + >> +/* <snip> >> + >> +static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings *timings) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + >> + mutex_lock(&state->mutex); > > Why you need to take the lock here? User accessible get/setters... But it doesn't look like other drivers do the same here. Maybe I went overkill adding extra locking earlier. > >> + >> + *timings = hdmi->timings; >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings *timings) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + struct v4l2_bt_timings *bt = &timings->bt; >> + int pixelclock; >> + int polarity; >> + >> + if (!timings) >> + return -EINVAL; >> + >> + memset(timings, 0, sizeof(struct v4l2_dv_timings)); >> + >> + if (!adv748x_hdmi_has_signal(state)) >> + return -ENOLINK; >> + >> + pixelclock = adv748x_hdmi_read_pixelclock(state); >> + if (pixelclock < 0) >> + return -ENODATA; >> + >> + timings->type = V4L2_DV_BT_656_1120; >> + >> + bt->pixelclock = pixelclock; >> + bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) & >> + ADV748X_HDMI_F1H1_INTERLACED ? >> + V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; >> + bt->width = hdmi_read16(state, ADV748X_HDMI_LW1, >> + ADV748X_HDMI_LW1_WIDTH_MASK); >> + bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1, >> + ADV748X_HDMI_F0H1_HEIGHT_MASK); >> + bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH, >> + ADV748X_HDMI_HFRONT_PORCH_MASK); >> + bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH, >> + ADV748X_HDMI_HSYNC_WIDTH_MASK); >> + bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH, >> + ADV748X_HDMI_HBACK_PORCH_MASK); >> + bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH, >> + ADV748X_HDMI_VFRONT_PORCH_MASK) / 2; >> + bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH, >> + ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2; >> + bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH, >> + ADV748X_HDMI_VBACK_PORCH_MASK) / 2; >> + > > Extra newline. Ah yes, I just found a nice sed to catch and remove these automatically. sed 'N;/^\n$/D;P;D;' Picked up 2 more lines from -core.c :) That should be part of checkpatch.pl somewhere ... Then I'd catch them as I commit. > >> + >> + polarity = hdmi_read(state, 0x05); >> + bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) | >> + (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0); >> + >> + if (bt->interlaced == V4L2_DV_INTERLACED) { >> + bt->height += hdmi_read16(state, 0x0b, 0x1fff); >> + bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2; >> + bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2; >> + bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2; >> + } >> + >> + adv748x_fill_optional_dv_timings(timings); >> + >> + /* >> + * No interrupt handling is implemented yet. >> + * There should be an IRQ when a cable is plugged and the new timings >> + * should be figured out and stored to state. >> + */ >> + hdmi->timings = *timings; >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + >> + mutex_lock(&state->mutex); > > Lock ? :-) > Now this one is talking to the i2c bus ... so I want to keep that - although now I've converted to regmap - it might well be locking the bus for me ... I'll have to check. >> + >> + *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL; >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + <snip> >> + >> +static int adv748x_hdmi_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + if (sdformat->pad != ADV748X_HDMI_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) >> + return adv748x_hdmi_get_format(sd, cfg, sdformat); >> + >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + *mbusformat = sdformat->format; > > Same comment as for adv748x_afe_set_format(). Ack. > >> + >> + return 0; >> +} >> + Thanks :)
On 06/13/2017 02:35 AM, Kieran Bingham wrote: > From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > Provide support for the ADV7481 and ADV7482. > > The driver is modelled with 4 subdevices to allow simultaneous streaming > from the AFE (Analog front end) and HDMI inputs though two CSI TX > entities. > > The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked > to the TXB CSI bus. > > The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, > and an earlier rework by Niklas Söderlund. > > Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > --- > > v2: > - Implement DT parsing > - adv748x: Add CSI2 entity > - adv748x: Rework pad allocations and fmts > - Give AFE 8 input pads and move pad defines > - Use the enums to ensure pads are referenced correctly. > - adv748x: Rename AFE/HDMI entities > Now they are 'just afe' and 'just hdmi' > - Reorder the entity enum and structures > - Added pad-format for the CSI2 entities > - CSI2 s_stream pass through > - CSI2 control pass through (with link following) > > v3: > - dt: Extend DT documentation to specify interrupt mappings > - simplify adv748x_parse_dt > - core: Add banner to header file describing ADV748x variants > - Use entity structure pointers rather than global state pointers where > possible > - afe: Reduce indent on afe_status > - hdmi: Add error checking to the bt->pixelclock values. > - Remove all unnecessary pad checks: handled by core > - Fix all probe cleanup paths > - adv748x_csi2_probe() now fails if it has no endpoint > - csi2: Fix small oneliners for is_txa and get_remote_sd() > - csi2: Fix checkpatch warnings > - csi2: Fix up s_stream pass-through > - csi2: Fix up Pixel Rate passthrough > - csi2: simplify adv748x_csi2_get_pad_format() > - Remove 'async notifiers' from AFE/HDMI > Using async notifiers was overkill, when we have access to the > subdevices internally and can register them directly. > - Use state lock in control handlers and clean up s_ctrls > - remove _interruptible mutex locks > > v4: > - all: Convert hex 0xXX to lowercase > - all: Use defines instead of hardcoded register values > - all: Use regmap > - afe, csi2, hdmi: _probe -> _init > - afe, csi2, hdmi: _remove -> _cleanup > - afe, hdmi: Convert pattern generator to a control > - afe, hdmi: get/set-fmt refactor > - afe, hdmi, csi2: Convert to internal calls for pixelrate > - afe: Allow the AFE to configure the Input Select from DT > - afe: Reduce indent on adv748x_afe_status switch > - afe: Remove ununsed macro definitions AIN0-7 > - afe: Remove extraneous control checks handled by core > - afe: Comment fixups > - afe: Rename error label > - afe: Correct control names on the SDP > - afe: Use AIN0-7 rather than AIN1-8 to match ports and MC pads > - core: adv748x_parse_dt references to nodes, and catch multiple > endpoints in a port. > - core: adv748x_dt_cleanup to simplify releasing DT nodes > - core: adv748x_print_info renamed to adv748x_identify_chip > - core: reorganise ordering of probe sequence > - core: No need for of_match_ptr > - core: Fix up i2c read/writes (regmap still on todo list) > - core: Set specific functions from the entities on subdev-init > - core: Use kzalloc for state instead of devm > - core: Improve probe error reporting > - core: Track unknown BIT(6) in tx{a,b}_power > - csi2: Improve adv748x_csi2_get_remote_sd as adv748x_csi2_get_source_sd > - csi2: -EPIPE instead of -ENODEV > - csi2: adv_dbg, instead of adv_info > - csi2: adv748x_csi2_set_format fix > - csi2: remove async notifier and sd member variables > - csi2: register links from the CSI2 > - csi2: create virtual channel helper function > - dt: Remove numbering from endpoints > - dt: describe ports and interrupts as optional > - dt: Re-tab > - hdmi: adv748x_hdmi_have_signal -> adv748x_hdmi_has_signal > - hdmi: fix adv748x_hdmi_read_pixelclock return checks > - hdmi: improve adv748x_hdmi_set_video_timings > - hdmi: Fix tmp variable as polarity > - hdmi: Improve adv748x_hdmi_s_stream > - hdmi: Clean up adv748x_hdmi_s_ctrl register definitions and usage > - hdmi: Fix up adv748x_hdmi_s_dv_timings with macro names for register > - hdmi: Add locking to adv748x_hdmi_g_dv_timings > writes and locking > - hdmi: adv748x_hdmi_set_de_timings function added to clarify DE writes > - hdmi: Use CP in control register naming to match component processor > - hdmi: clean up adv748x_hdmi_query_dv_timings() > - KConfig: Fix up dependency and capitalisation > > > Documentation/devicetree/bindings/media/i2c/adv748x.txt | 96 +- This should be a separate patch cross posted to the devicetree mailinglist. > MAINTAINERS | 6 +- This should also be a separate patch. > drivers/media/i2c/Kconfig | 11 +- > drivers/media/i2c/Makefile | 1 +- > drivers/media/i2c/adv748x/Makefile | 7 +- > drivers/media/i2c/adv748x/adv748x-afe.c | 571 ++++++- > drivers/media/i2c/adv748x/adv748x-core.c | 907 +++++++++- > drivers/media/i2c/adv748x/adv748x-csi2.c | 323 +++- > drivers/media/i2c/adv748x/adv748x-hdmi.c | 652 ++++++- > drivers/media/i2c/adv748x/adv748x.h | 415 ++++- > 10 files changed, 2989 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/adv748x.txt > create mode 100644 drivers/media/i2c/adv748x/Makefile > create mode 100644 drivers/media/i2c/adv748x/adv748x-afe.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-core.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-csi2.c > create mode 100644 drivers/media/i2c/adv748x/adv748x-hdmi.c > create mode 100644 drivers/media/i2c/adv748x/adv748x.h > > diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt > new file mode 100644 > index 000000000000..b17f8983c992 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt > @@ -0,0 +1,96 @@ > +* Analog Devices ADV748X video decoder with HDMI receiver > + > +The ADV7481, and ADV7482 are multi format video decoders with an integrated No comma needed. > +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB > +from three input sources HDMI, analog and TTL. > + > +Required Properties: > + > + - compatible: Must contain one of the following > + - "adi,adv7481" for the ADV7481 > + - "adi,adv7482" for the ADV7482 > + > + - reg: I2C slave address > + > +Optional Properties: > + > + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or > + "intrq3". All interrupts are optional. The "intrq3" interrupt > + is only available on the adv7481 > + - interrupts: Specify the interrupt lines for the ADV748x > + > +The device node must contain one 'port' child node per device input and output > +port, in accordance with the video interface bindings defined in > +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes > +are numbered as follows. > + > + Name Type Port > + --------------------------------------- > + AIN0 sink 0 > + AIN1 sink 1 > + AIN2 sink 2 > + AIN3 sink 3 > + AIN4 sink 4 > + AIN5 sink 5 > + AIN6 sink 6 > + AIN7 sink 7 > + HDMI sink 8 > + TTL sink 9 > + TXA source 10 > + TXB source 11 > + > +The digital output port nodes must contain at least one endpoint. > + > +Ports are optional if they are not connected to anything at the hardware level, > +but the driver may not provide any support for ports which are not described. Not sure what is meant by 'but the driver may not provide any support for ports which are not described'. Isn't that expected behavior if you leave out the port? > + > +Example: > + > + video_receiver@70 { > + compatible = "adi,adv7482"; > + reg = <0x70>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&gpio6>; > + interrupt-names = "intrq1", "intrq2"; > + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, > + <31 IRQ_TYPE_LEVEL_LOW>; > + > + port@7 { > + reg = <7>; > + > + adv7482_ain7: endpoint { > + remote-endpoint = <&cvbs_in>; > + }; > + }; > + > + port@8 { > + reg = <8>; > + > + adv7482_hdmi: endpoint { > + remote-endpoint = <&hdmi_in>; > + }; > + }; > + > + port@10 { > + reg = <10>; > + > + adv7482_txa: endpoint { > + clock-lanes = <0>; > + data-lanes = <1 2 3 4>; > + remote-endpoint = <&csi40_in>; > + }; > + }; > + > + port@11 { > + reg = <11>; > + > + adv7482_txb: endpoint { > + clock-lanes = <0>; > + data-lanes = <1>; > + remote-endpoint = <&csi20_in>; > + }; > + }; > + }; > diff --git a/MAINTAINERS b/MAINTAINERS > index eaaa35419fa2..7e2b65240a6f 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -776,6 +776,12 @@ L: linux-media@vger.kernel.org > S: Maintained > F: drivers/media/i2c/adv7511* > > +ANALOG DEVICES INC ADV748X DRIVER > +M: Kieran Bingham <kieran.bingham@ideasonboard.com> > +L: linux-media@vger.kernel.org > +S: Maintained > +F: drivers/media/i2c/adv748x/* > + > ANALOG DEVICES INC ADV7604 DRIVER > M: Hans Verkuil <hans.verkuil@cisco.com> > L: linux-media@vger.kernel.org > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 7c23b7a1fd05..fcbec4273fef 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -204,6 +204,17 @@ config VIDEO_ADV7183 > To compile this driver as a module, choose M here: the > module will be called adv7183. > > +config VIDEO_ADV748X > + tristate "Analog Devices ADV748x decoder" > + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API > + depends on OF > + ---help--- > + V4L2 subdevice driver for the Analog Devices > + ADV7481 and ADV7482 HDMI/Analog video decoders. > + > + To compile this driver as a module, choose M here: the > + module will be called adv748x. > + > config VIDEO_ADV7604 > tristate "Analog Devices ADV7604 decoder" > depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index 62323ec66be8..e0e6045a2ec8 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o > obj-$(CONFIG_VIDEO_ADV7183) += adv7183.o > obj-$(CONFIG_VIDEO_ADV7343) += adv7343.o > obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o > +obj-$(CONFIG_VIDEO_ADV748X) += adv748x/ > obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o > obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o > obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o > diff --git a/drivers/media/i2c/adv748x/Makefile b/drivers/media/i2c/adv748x/Makefile > new file mode 100644 > index 000000000000..c0711e076f1d > --- /dev/null > +++ b/drivers/media/i2c/adv748x/Makefile > @@ -0,0 +1,7 @@ > +adv748x-objs := \ > + adv748x-afe.o \ > + adv748x-core.o \ > + adv748x-csi2.o \ > + adv748x-hdmi.o > + > +obj-$(CONFIG_VIDEO_ADV748X) += adv748x.o > diff --git a/drivers/media/i2c/adv748x/adv748x-afe.c b/drivers/media/i2c/adv748x/adv748x-afe.c > new file mode 100644 > index 000000000000..28e95b292d9b > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-afe.c > @@ -0,0 +1,571 @@ > +/* > + * Driver for Analog Devices ADV748X 8 channel analog front end (AFE) receiver > + * with standard definition processor (SDP) > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/delay.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/v4l2-dv-timings.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * SDP > + */ > + > +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM 0x0 > +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1 > +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_J_SECAM 0x2 > +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_M_SECAM 0x3 > +#define ADV748X_AFE_STD_NTSC_J 0x4 > +#define ADV748X_AFE_STD_NTSC_M 0x5 > +#define ADV748X_AFE_STD_PAL60 0x6 > +#define ADV748X_AFE_STD_NTSC_443 0x7 > +#define ADV748X_AFE_STD_PAL_BG 0x8 > +#define ADV748X_AFE_STD_PAL_N 0x9 > +#define ADV748X_AFE_STD_PAL_M 0xa > +#define ADV748X_AFE_STD_PAL_M_PED 0xb > +#define ADV748X_AFE_STD_PAL_COMB_N 0xc > +#define ADV748X_AFE_STD_PAL_COMB_N_PED 0xd > +#define ADV748X_AFE_STD_PAL_SECAM 0xe > +#define ADV748X_AFE_STD_PAL_SECAM_PED 0xf > + > +static int adv748x_afe_read_ro_map(struct adv748x_state *state, u8 reg) > +{ > + int ret; > + > + /* Select SDP Read-Only Main Map */ > + ret = sdp_write(state, ADV748X_SDP_MAP_SEL, > + ADV748X_SDP_MAP_SEL_RO_MAIN); > + if (ret < 0) > + return ret; > + > + return sdp_read(state, reg); > +} > + > +static int adv748x_afe_status(struct adv748x_afe *afe, u32 *signal, > + v4l2_std_id *std) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int info; > + > + /* Read status from reg 0x10 of SDP RO Map */ > + info = adv748x_afe_read_ro_map(state, ADV748X_SDP_RO_10); > + if (info < 0) > + return info; > + > + if (signal) > + *signal = info & ADV748X_SDP_RO_10_IN_LOCK ? > + 0 : V4L2_IN_ST_NO_SIGNAL; > + > + if (!std) > + return 0; > + > + /* Standard not valid if there is no signal */ > + if (info & BIT(0)) { > + *std = V4L2_STD_UNKNOWN; > + return 0; > + } > + > + switch (info & 0x70) { > + case 0x00: > + *std = V4L2_STD_NTSC; > + break; > + case 0x10: > + *std = V4L2_STD_NTSC_443; > + break; > + case 0x20: > + *std = V4L2_STD_PAL_M; > + break; > + case 0x30: > + *std = V4L2_STD_PAL_60; > + break; > + case 0x40: > + *std = V4L2_STD_PAL; > + break; > + case 0x50: > + *std = V4L2_STD_SECAM; > + break; > + case 0x60: > + *std = V4L2_STD_PAL_Nc | V4L2_STD_PAL_N; > + break; > + case 0x70: > + *std = V4L2_STD_SECAM; > + break; > + default: > + *std = V4L2_STD_UNKNOWN; > + break; > + } > + > + return 0; > +} > + > +static void adv748x_afe_fill_format(struct adv748x_afe *afe, > + struct v4l2_mbus_framefmt *fmt) > +{ > + v4l2_std_id std; > + > + memset(fmt, 0, sizeof(*fmt)); > + > + fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; > + fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; > + fmt->field = V4L2_FIELD_INTERLACED; > + > + fmt->width = 720; > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, &std); > + else > + std = afe->curr_norm; > + > + fmt->height = std & V4L2_STD_525_60 ? 480 : 576; > +} > + > +static int adv748x_afe_std(v4l2_std_id std) > +{ > + if (std == V4L2_STD_ALL) > + return ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM; > + if (std == V4L2_STD_PAL_60) > + return ADV748X_AFE_STD_PAL60; > + if (std == V4L2_STD_NTSC_443) > + return ADV748X_AFE_STD_NTSC_443; > + if (std == V4L2_STD_PAL_N) > + return ADV748X_AFE_STD_PAL_N; > + if (std == V4L2_STD_PAL_M) > + return ADV748X_AFE_STD_PAL_M; > + if (std == V4L2_STD_PAL_Nc) > + return ADV748X_AFE_STD_PAL_COMB_N; > + if (std & V4L2_STD_PAL) > + return ADV748X_AFE_STD_PAL_BG; > + if (std & V4L2_STD_NTSC) > + return ADV748X_AFE_STD_NTSC_M; This NTSC test should come before the PAL test. This is the order other drivers do this as well. So a standard with a mix of NTSC and PAL bits will map to NTSC. > + if (std & V4L2_STD_SECAM) > + return ADV748X_AFE_STD_PAL_SECAM; > + > + return -EINVAL; > +} > + > +static int adv748x_afe_set_video_standard(struct adv748x_state *state, > + v4l2_std_id std) > +{ > + int sdpstd; > + > + sdpstd = adv748x_afe_std(std); > + if (sdpstd < 0) > + return sdpstd; > + > + sdp_clrset(state, ADV748X_SDP_VID_SEL, ADV748X_SDP_VID_SEL_MASK, > + (sdpstd & 0xf) << ADV748X_SDP_VID_SEL_SHIFT); > + > + return 0; > +} > + > +static int adv748x_afe_s_input(struct adv748x_afe *afe, unsigned int input) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + > + return sdp_write(state, ADV748X_SDP_INSEL, input); > +} > + > +static int adv748x_afe_g_pixelaspect(struct v4l2_subdev *sd, > + struct v4l2_fract *aspect) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + v4l2_std_id std; > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, &std); > + else > + std = afe->curr_norm; > + > + if (std & V4L2_STD_525_60) { > + aspect->numerator = 11; > + aspect->denominator = 10; > + } else { > + aspect->numerator = 54; > + aspect->denominator = 59; > + } > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_afe_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + > + if (afe->curr_norm == V4L2_STD_ALL) > + adv748x_afe_status(afe, NULL, norm); > + else > + *norm = afe->curr_norm; > + > + return 0; > +} > + > +static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_afe_set_video_standard(state, std); > + if (ret == 0) > + afe->curr_norm = std; OK, so this is a bit of a problem: you are using V4L2_STD_ALL as an autodetect mechanism, but that is not allowed by the V4L2 specification. Yes, some old drivers do this and we don't dare to change that, but new drivers should not attempt this. The standard set and reported by s_std and g_std must always be precise, i.e. no mix of NTSC and PAL. Only QUERYSTD is allowed to detect the format. So > + > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + if (afe->streaming) { > + ret = -EBUSY; > + goto unlock; > + } > + > + /* Set auto detect mode */ > + ret = adv748x_afe_set_video_standard(state, V4L2_STD_ALL); > + if (ret) > + goto unlock; > + > + msleep(100); > + > + /* Read detected standard */ > + ret = adv748x_afe_status(afe, NULL, std); > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static int adv748x_afe_g_tvnorms(struct v4l2_subdev *sd, v4l2_std_id *norm) > +{ > + *norm = V4L2_STD_ALL; > + > + return 0; > +} > + > +static int adv748x_afe_g_input_status(struct v4l2_subdev *sd, u32 *status) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_afe_status(afe, status, NULL); > + > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_afe_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret, signal = V4L2_IN_ST_NO_SIGNAL; > + > + mutex_lock(&state->mutex); > + > + if (enable) { > + ret = adv748x_afe_s_input(afe, afe->input); > + if (ret) > + goto unlock; > + } > + > + ret = adv748x_txb_power(state, enable); > + if (ret) > + goto unlock; > + > + afe->streaming = enable; > + > + adv748x_afe_status(afe, &signal, NULL); > + if (signal != V4L2_IN_ST_NO_SIGNAL) > + adv_dbg(state, "Detected SDP signal\n"); > + else > + adv_dbg(state, "Couldn't detect SDP video signal\n"); > + > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static const struct v4l2_subdev_video_ops adv748x_afe_video_ops = { > + .g_std = adv748x_afe_g_std, > + .s_std = adv748x_afe_s_std, > + .querystd = adv748x_afe_querystd, > + .g_tvnorms = adv748x_afe_g_tvnorms, > + .g_input_status = adv748x_afe_g_input_status, > + .s_stream = adv748x_afe_s_stream, > + .g_pixelaspect = adv748x_afe_g_pixelaspect, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + */ > + > +static int adv748x_afe_set_pixelrate(struct adv748x_afe *afe) > +{ > + struct v4l2_subdev *tx; > + unsigned int width, height, fps; > + > + tx = adv748x_get_remote_sd(&afe->pads[ADV748X_AFE_SOURCE]); > + if (!tx) > + return -ENOLINK; > + > + width = 720; > + height = afe->curr_norm & V4L2_STD_525_60 ? 480 : 576; > + fps = afe->curr_norm & V4L2_STD_525_60 ? 30 : 25; > + > + return adv748x_csi2_set_pixelrate(tx, width * height * fps); > +} > + > +static int adv748x_afe_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->index != 0) > + return -EINVAL; > + > + code->code = MEDIA_BUS_FMT_UYVY8_2X8; > + > + return 0; > +} > + > +static int adv748x_afe_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); > + struct v4l2_mbus_framefmt *mbusformat; > + > + /* The format of the analog sink pads is nonsensical */ You mean: /* It makes no sense to get the format of analog sink pads */ I misread your comment as meaning that the *format* made no sense. > + if (sdformat->pad != ADV748X_AFE_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + sdformat->format = *mbusformat; > + } else { > + adv748x_afe_fill_format(afe, &sdformat->format); > + adv748x_afe_set_pixelrate(afe); > + } > + > + return 0; > +} > + > +static int adv748x_afe_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct v4l2_mbus_framefmt *mbusformat; > + > + /* The format of the analog sink pads is nonsensical */ Ditto. > + if (sdformat->pad != ADV748X_AFE_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) > + return adv748x_afe_get_format(sd, cfg, sdformat); > + > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + *mbusformat = sdformat->format; > + > + return 0; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_afe_pad_ops = { > + .enum_mbus_code = adv748x_afe_enum_mbus_code, > + .set_fmt = adv748x_afe_set_format, > + .get_fmt = adv748x_afe_get_format, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_afe_ops = { > + .video = &adv748x_afe_video_ops, > + .pad = &adv748x_afe_pad_ops, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Controls > + */ > + > +static const char * const afe_ctrl_frp_menu[] = { > + "Disabled", > + "Default Value", What does this mean? It is not very descriptive. > + "Color Bars", > + "Grey Ramp", > + "Cb Ramp", > + "Cr Ramp", > + "Boundary" > +}; > + > +static int adv748x_afe_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct adv748x_afe *afe = adv748x_ctrl_to_afe(ctrl); > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + bool enable; > + int ret; > + > + ret = sdp_write(state, 0x0e, 0x00); > + if (ret < 0) > + return ret; > + > + switch (ctrl->id) { > + case V4L2_CID_BRIGHTNESS: > + ret = sdp_write(state, ADV748X_SDP_BRI, ctrl->val); > + break; > + case V4L2_CID_HUE: > + /* Hue is inverted according to HSL chart */ > + ret = sdp_write(state, ADV748X_SDP_HUE, -ctrl->val); > + break; > + case V4L2_CID_CONTRAST: > + ret = sdp_write(state, ADV748X_SDP_CON, ctrl->val); > + break; > + case V4L2_CID_SATURATION: > + ret = sdp_write(state, ADV748X_SDP_SD_SAT_U, ctrl->val); > + if (ret) > + break; > + ret = sdp_write(state, ADV748X_SDP_SD_SAT_V, ctrl->val); > + break; > + case V4L2_CID_TEST_PATTERN: > + enable = !!ctrl->val; > + > + /* Enable/Disable Color bar test patterns */ > + ret = sdp_clrset(state, ADV748X_SDP_DEF, ADV748X_SDP_DEF_VAL_EN, > + enable); > + if (ret) > + break; > + ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, > + enable ? ctrl->val - 1 : 0); > + break; > + default: > + return -EINVAL; > + } > + > + return ret; > +} > + > +static const struct v4l2_ctrl_ops adv748x_afe_ctrl_ops = { > + .s_ctrl = adv748x_afe_s_ctrl, > +}; > + > +static int adv748x_afe_init_controls(struct adv748x_afe *afe) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + > + v4l2_ctrl_handler_init(&afe->ctrl_hdl, 5); > + > + /* Use our mutex for the controls */ > + afe->ctrl_hdl.lock = &state->mutex; > + > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_BRIGHTNESS, ADV748X_SDP_BRI_MIN, > + ADV748X_SDP_BRI_MAX, 1, ADV748X_SDP_BRI_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_CONTRAST, ADV748X_SDP_CON_MIN, > + ADV748X_SDP_CON_MAX, 1, ADV748X_SDP_CON_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_SATURATION, ADV748X_SDP_SAT_MIN, > + ADV748X_SDP_SAT_MAX, 1, ADV748X_SDP_SAT_DEF); > + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_HUE, ADV748X_SDP_HUE_MIN, > + ADV748X_SDP_HUE_MAX, 1, ADV748X_SDP_HUE_DEF); > + > + v4l2_ctrl_new_std_menu_items(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(afe_ctrl_frp_menu) - 1, > + 0, 0, afe_ctrl_frp_menu); > + > + afe->sd.ctrl_handler = &afe->ctrl_hdl; > + if (afe->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&afe->ctrl_hdl); > + return afe->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&afe->ctrl_hdl); > +} > + > +int adv748x_afe_init(struct adv748x_afe *afe) > +{ > + struct adv748x_state *state = adv748x_afe_to_state(afe); > + int ret; > + unsigned int i; > + > + afe->input = 0; > + afe->streaming = false; > + afe->curr_norm = V4L2_STD_ALL; No. This must be a valid standard. Typically V4L2_STD_NTSC_M. > + > + adv748x_subdev_init(&afe->sd, state, &adv748x_afe_ops, > + MEDIA_ENT_F_ATV_DECODER, "afe"); > + > + /* Identify the first connector found as a default input if set */ > + for (i = ADV748X_PORT_AIN0; i <= ADV748X_PORT_AIN7; i++) { > + /* Inputs and ports are 1-indexed to match the data sheet */ > + if (state->endpoints[i]) { > + afe->input = i; > + break; > + } > + } > + > + adv748x_afe_s_input(afe, afe->input); > + > + adv_dbg(state, "AFE Default input set to %d\n", afe->input); > + > + /* Entity pads and sinks are 0-indexed to match the pads */ > + for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++) > + afe->pads[i].flags = MEDIA_PAD_FL_SINK; > + > + afe->pads[ADV748X_AFE_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&afe->sd.entity, ADV748X_AFE_NR_PADS, > + afe->pads); > + if (ret) > + return ret; > + > + ret = adv748x_afe_init_controls(afe); > + if (ret) > + goto error; > + > + return 0; > + > +error: > + media_entity_cleanup(&afe->sd.entity); > + > + return ret; > +} > + > +void adv748x_afe_cleanup(struct adv748x_afe *afe) > +{ > + v4l2_device_unregister_subdev(&afe->sd); > + media_entity_cleanup(&afe->sd.entity); > + v4l2_ctrl_handler_free(&afe->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c > new file mode 100644 > index 000000000000..6e395a4524ec > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-core.c > @@ -0,0 +1,907 @@ > +/* > + * Driver for Analog Devices ADV748X HDMI receiver with AFE > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + * > + * Authors: > + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> > + * Niklas Söderlund <niklas.soderlund@ragnatech.se> > + * Kieran Bingham <kieran.bingham@ideasonboard.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/errno.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/of_graph.h> > +#include <linux/regmap.h> > +#include <linux/v4l2-dv-timings.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * Register manipulation > + */ > + > +static const struct regmap_config adv748x_regmap_cnf[] = { > + { > + .name = "io", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "dpll", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "cp", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "hdmi", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "edid", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "repeater", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "infoframe", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "cec", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "sdp", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + > + { > + .name = "txb", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > + { > + .name = "txa", > + .reg_bits = 8, > + .val_bits = 8, > + > + .max_register = 0xff, > + .cache_type = REGCACHE_NONE, > + }, > +}; > + > +static int adv748x_configure_regmap(struct adv748x_state *state, int region) > +{ > + int err; > + > + if (!state->i2c_clients[region]) > + return -ENODEV; > + > + state->regmap[region] = > + devm_regmap_init_i2c(state->i2c_clients[region], > + &adv748x_regmap_cnf[region]); > + > + if (IS_ERR(state->regmap[region])) { > + err = PTR_ERR(state->regmap[region]); > + adv_err(state, > + "Error initializing regmap %d with error %d\n", > + region, err); > + return -EINVAL; > + } > + > + return 0; > +} > + > +/* Default addresses for the I2C pages */ > +static int adv748x_i2c_addresses[ADV748X_PAGE_MAX] = { > + ADV748X_I2C_IO, > + ADV748X_I2C_DPLL, > + ADV748X_I2C_CP, > + ADV748X_I2C_HDMI, > + ADV748X_I2C_EDID, > + ADV748X_I2C_REPEATER, > + ADV748X_I2C_INFOFRAME, > + ADV748X_I2C_CEC, > + ADV748X_I2C_SDP, > + ADV748X_I2C_TXB, > + ADV748X_I2C_TXA, > +}; > + > +static int adv748x_read_check(struct adv748x_state *state, > + int client_page, u8 reg) > +{ > + struct i2c_client *client = state->i2c_clients[client_page]; > + int err; > + unsigned int val; > + > + err = regmap_read(state->regmap[client_page], reg, &val); > + > + if (err) { > + adv_err(state, "error reading %02x, %02x\n", > + client->addr, reg); > + return err; > + } > + > + return val; > +} > + > +int adv748x_read(struct adv748x_state *state, u8 page, u8 reg) > +{ > + return adv748x_read_check(state, page, reg); > +} > + > +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value) > +{ > + return regmap_write(state->regmap[page], reg, value); > +} > + > +/* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX > + * size to one or more registers. > + * > + * A value of zero will be returned on success, a negative errno will > + * be returned in error cases. > + */ > +int adv748x_write_block(struct adv748x_state *state, int client_page, > + unsigned int init_reg, const void *val, > + size_t val_len) > +{ > + struct regmap *regmap = state->regmap[client_page]; > + > + if (val_len > I2C_SMBUS_BLOCK_MAX) > + val_len = I2C_SMBUS_BLOCK_MAX; > + > + return regmap_raw_write(regmap, init_reg, val, val_len); > +} > + > + > +static struct i2c_client *adv748x_dummy_client(struct adv748x_state *state, > + u8 addr, u8 io_reg) > +{ > + struct i2c_client *client = state->client; > + > + if (addr) > + io_write(state, io_reg, addr << 1); > + > + return i2c_new_dummy(client->adapter, io_read(state, io_reg) >> 1); > +} > + > +static void adv748x_unregister_clients(struct adv748x_state *state) > +{ > + unsigned int i; > + > + for (i = 1; i < ARRAY_SIZE(state->i2c_clients); ++i) { > + if (state->i2c_clients[i]) > + i2c_unregister_device(state->i2c_clients[i]); > + } > +} > + > +static int adv748x_initialise_clients(struct adv748x_state *state) > +{ > + int i; > + int ret; > + > + for (i = ADV748X_PAGE_DPLL; i < ADV748X_PAGE_MAX; ++i) { > + state->i2c_clients[i] = > + adv748x_dummy_client(state, adv748x_i2c_addresses[i], > + ADV748X_IO_SLAVE_ADDR_BASE + i); > + if (state->i2c_clients[i] == NULL) { > + adv_err(state, "failed to create i2c client %u\n", i); > + return -ENOMEM; > + } > + > + ret = adv748x_configure_regmap(state, i); > + if (ret) > + return ret; > + } > + > + return 0; > +} > + > +/** > + * struct adv748x_reg_value - Register write instruction > + * @page: Regmap page identifier > + * @reg: I2C register > + * @value: value to write to @page at @reg > + */ > +struct adv748x_reg_value { > + u8 page; > + u8 reg; > + u8 value; > +}; > + > +static int adv748x_write_regs(struct adv748x_state *state, > + const struct adv748x_reg_value *regs) > +{ > + int ret; > + > + while (regs->page != ADV748X_PAGE_EOR) { > + if (regs->page == ADV748X_PAGE_WAIT) { > + msleep(regs->value); > + } else { > + ret = adv748x_write(state, regs->page, regs->reg, > + regs->value); > + if (ret < 0) { > + adv_err(state, > + "Error regs page: 0x%02x reg: 0x%02x\n", > + regs->page, regs->reg); > + return ret; > + } > + } > + regs++; > + } > + > + return 0; > +} > + > + > +/* ----------------------------------------------------------------------------- > + * TXA and TXB > + */ > + > +static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = { > + > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = { > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x3b}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = { > + > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ > + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ > + > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = { > + > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x3b}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +int adv748x_txa_power(struct adv748x_state *state, bool on) > +{ > + int val; > + > + val = txa_read(state, ADV748X_CSI_FS_AS_LS); > + if (val < 0) > + return val; > + > + /* > + * This test against BIT(6) is not documented by the datasheet, but was > + * specified in the downstream driver. > + * Track with a WARN_ONCE to determine if it is ever set by HW. > + */ > + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), > + "Enabling with unknown bit set"); > + > + if (on) > + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); > + else 'else' isn't needed. > + return adv748x_write_regs(state, adv748x_power_down_txa_4lane); > +} > + > +int adv748x_txb_power(struct adv748x_state *state, bool on) > +{ > + int val; > + > + val = txb_read(state, ADV748X_CSI_FS_AS_LS); > + if (val < 0) > + return val; > + > + /* > + * This test against BIT(6) is not documented by the datasheet, but was > + * specified in the downstream driver. > + * Track with a WARN_ONCE to determine if it is ever set by HW. > + */ > + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), > + "Enabling with unknown bit set"); > + > + if (on) > + return adv748x_write_regs(state, adv748x_power_up_txb_1lane); > + else Ditto. > + return adv748x_write_regs(state, adv748x_power_down_txb_1lane); > +} > + > +/* ----------------------------------------------------------------------------- > + * Media Operations > + */ > + > +static const struct media_entity_operations adv748x_media_ops = { > + .link_validate = v4l2_subdev_link_validate, > +}; > + > +/* ----------------------------------------------------------------------------- > + * HW setup > + */ > + > +static const struct adv748x_reg_value adv748x_sw_reset[] = { > + > + {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */ > + {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */ > + {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */ > + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static const struct adv748x_reg_value adv748x_set_slave_address[] = { > + {ADV748X_PAGE_IO, 0xf3, ADV748X_I2C_DPLL << 1}, > + {ADV748X_PAGE_IO, 0xf4, ADV748X_I2C_CP << 1}, > + {ADV748X_PAGE_IO, 0xf5, ADV748X_I2C_HDMI << 1}, > + {ADV748X_PAGE_IO, 0xf6, ADV748X_I2C_EDID << 1}, > + {ADV748X_PAGE_IO, 0xf7, ADV748X_I2C_REPEATER << 1}, > + {ADV748X_PAGE_IO, 0xf8, ADV748X_I2C_INFOFRAME << 1}, > + {ADV748X_PAGE_IO, 0xfa, ADV748X_I2C_CEC << 1}, > + {ADV748X_PAGE_IO, 0xfb, ADV748X_I2C_SDP << 1}, > + {ADV748X_PAGE_IO, 0xfc, ADV748X_I2C_TXB << 1}, > + {ADV748X_PAGE_IO, 0xfd, ADV748X_I2C_TXA << 1}, > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +/* Supported Formats For Script Below */ > +/* - 01-29 HDMI to MIPI TxA CSI 4-Lane - RGB888: */ > +static const struct adv748x_reg_value adv748x_init_txa_4lane[] = { > + /* Disable chip powerdown & Enable HDMI Rx block */ > + {ADV748X_PAGE_IO, 0x00, 0x40}, > + > + {ADV748X_PAGE_REPEATER, 0x40, 0x83}, /* Enable HDCP 1.1 */ > + > + {ADV748X_PAGE_HDMI, 0x00, 0x08},/* Foreground Channel = A */ > + {ADV748X_PAGE_HDMI, 0x98, 0xff},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x99, 0xa3},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9a, 0x00},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9b, 0x0a},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x9d, 0x40},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0xcb, 0x09},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3d, 0x10},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3e, 0x7b},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x3f, 0x5e},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x4e, 0xfe},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x4f, 0x18},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x57, 0xa3},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x58, 0x04},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0x85, 0x10},/* ADI Required Write */ > + > + {ADV748X_PAGE_HDMI, 0x83, 0x00},/* Enable All Terminations */ > + {ADV748X_PAGE_HDMI, 0xa3, 0x01},/* ADI Required Write */ > + {ADV748X_PAGE_HDMI, 0xbe, 0x00},/* ADI Required Write */ > + > + {ADV748X_PAGE_HDMI, 0x6c, 0x01},/* HPA Manual Enable */ > + {ADV748X_PAGE_HDMI, 0xf8, 0x01},/* HPA Asserted */ > + {ADV748X_PAGE_HDMI, 0x0f, 0x00},/* Audio Mute Speed Set to Fastest */ > + /* (Smallest Step Size) */ > + > + {ADV748X_PAGE_IO, 0x04, 0x02}, /* RGB Out of CP */ > + {ADV748X_PAGE_IO, 0x12, 0xf0}, /* CSC Depends on ip Packets, SDR 444 */ > + {ADV748X_PAGE_IO, 0x17, 0x80}, /* Luma & Chroma can reach 254d */ > + {ADV748X_PAGE_IO, 0x03, 0x86}, /* CP-Insert_AV_Code */ > + > + {ADV748X_PAGE_CP, 0x7c, 0x00}, /* ADI Required Write */ > + > + {ADV748X_PAGE_IO, 0x0c, 0xe0}, /* Enable LLC_DLL & Double LLC Timing */ > + {ADV748X_PAGE_IO, 0x0e, 0xdd}, /* LLC/PIX/SPI PINS TRISTATED AUD */ > + /* Outputs Enabled */ > + {ADV748X_PAGE_IO, 0x10, 0xa0}, /* Enable 4-lane CSI Tx & Pixel Port */ > + > + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ > + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ > + {ADV748X_PAGE_TXA, 0xdb, 0x10}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xd6, 0x07}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xc4, 0x0a}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x71, 0x33}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x72, 0x11}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ > + > + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +/* 02-01 Analog CVBS to MIPI TX-B CSI 1-Lane - */ > +/* Autodetect CVBS Single Ended In Ain 1 - MIPI Out */ > +static const struct adv748x_reg_value adv748x_init_txb_1lane[] = { > + > + {ADV748X_PAGE_IO, 0x00, 0x30}, /* Disable chip powerdown Rx */ > + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ > + > + {ADV748X_PAGE_IO, 0x0e, 0xff}, /* LLC/PIX/AUD/SPI PINS TRISTATED */ > + > + {ADV748X_PAGE_SDP, 0x0f, 0x00}, /* Exit Power Down Mode */ > + {ADV748X_PAGE_SDP, 0x52, 0xcd}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x0e, 0x80}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x9c, 0x00}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x9c, 0xff}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x0e, 0x00}, /* ADI Required Write */ > + > + /* ADI recommended writes for improved video quality */ > + {ADV748X_PAGE_SDP, 0x80, 0x51}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x81, 0x51}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0x82, 0x68}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x03, 0x42}, /* Tri-S Output , PwrDwn 656 pads */ > + {ADV748X_PAGE_SDP, 0x04, 0xb5}, /* ITU-R BT.656-4 compatible */ > + {ADV748X_PAGE_SDP, 0x13, 0x00}, /* ADI Required Write */ > + > + {ADV748X_PAGE_SDP, 0x17, 0x41}, /* Select SH1 */ > + {ADV748X_PAGE_SDP, 0x31, 0x12}, /* ADI Required Write */ > + {ADV748X_PAGE_SDP, 0xe6, 0x4f}, /* V bit end pos manually in NTSC */ > + > + /* Enable 1-Lane MIPI Tx, */ > + /* enable pixel output and route SD through Pixel port */ > + {ADV748X_PAGE_IO, 0x10, 0x70}, > + > + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ > + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ > + {ADV748X_PAGE_TXB, 0xd2, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xc4, 0x0a}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x71, 0x33}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x72, 0x11}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ > + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ > + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ > + > + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ > + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ > + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ > + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ > + > + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > +}; > + > +static int adv748x_reset(struct adv748x_state *state) > +{ > + int ret; > + > + ret = adv748x_write_regs(state, adv748x_sw_reset); > + if (ret < 0) > + return ret; > + > + ret = adv748x_write_regs(state, adv748x_set_slave_address); > + if (ret < 0) > + return ret; > + > + /* Init and power down TXA */ > + ret = adv748x_write_regs(state, adv748x_init_txa_4lane); > + if (ret) > + return ret; > + > + adv748x_txa_power(state, 0); > + > + /* Init and power down TXB */ > + ret = adv748x_write_regs(state, adv748x_init_txb_1lane); > + if (ret) > + return ret; > + > + adv748x_txb_power(state, 0); > + > + /* Disable chip powerdown & Enable HDMI Rx block */ > + io_write(state, ADV748X_IO_PD, ADV748X_IO_PD_RX_EN); > + > + /* Enable 4-lane CSI Tx & Pixel Port */ > + io_write(state, ADV748X_IO_10, ADV748X_IO_10_CSI4_EN | > + ADV748X_IO_10_CSI1_EN | > + ADV748X_IO_10_PIX_OUT_EN); > + > + /* Use vid_std and v_freq as freerun resolution for CP */ > + cp_clrset(state, ADV748X_CP_CLMP_POS, ADV748X_CP_CLMP_POS_DIS_AUTO, > + ADV748X_CP_CLMP_POS_DIS_AUTO); > + > + return 0; > +} > + > +static int adv748x_identify_chip(struct adv748x_state *state) > +{ > + int msb, lsb; > + > + lsb = io_read(state, ADV748X_IO_CHIP_REV_ID_1); > + msb = io_read(state, ADV748X_IO_CHIP_REV_ID_2); > + > + if (lsb < 0 || msb < 0) { > + adv_err(state, "Failed to read chip revision\n"); > + return -EIO; > + } > + > + adv_info(state, "chip found @ 0x%02x revision %02x%02x\n", > + state->client->addr << 1, lsb, msb); > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * i2c driver > + */ > + > +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, > + const struct v4l2_subdev_ops *ops, u32 function, > + const char *ident) > +{ > + v4l2_subdev_init(sd, ops); > + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + > + /* the owner is the same as the i2c_client's driver owner */ > + sd->owner = state->dev->driver->owner; > + sd->dev = state->dev; > + > + v4l2_set_subdevdata(sd, state); > + > + /* initialize name */ > + snprintf(sd->name, sizeof(sd->name), "%s %d-%04x %s", > + state->dev->driver->name, > + i2c_adapter_id(state->client->adapter), > + state->client->addr, ident); > + > + sd->entity.function = function; > + sd->entity.ops = &adv748x_media_ops; > +} > + > +static int adv748x_parse_dt(struct adv748x_state *state) > +{ > + struct device_node *ep_np = NULL; > + struct of_endpoint ep; > + bool found = false; > + > + for_each_endpoint_of_node(state->dev->of_node, ep_np) { > + of_graph_parse_endpoint(ep_np, &ep); > + adv_info(state, "Endpoint %s on port %d", > + of_node_full_name(ep.local_node), > + ep.port); > + > + if (ep.port >= ADV748X_PORT_MAX) { > + adv_err(state, "Invalid endpoint %s on port %d", > + of_node_full_name(ep.local_node), > + ep.port); > + > + continue; > + } > + > + if (state->endpoints[ep.port]) { > + adv_err(state, > + "Multiple port endpoints are not supported"); > + continue; > + } > + > + of_node_get(ep_np); > + state->endpoints[ep.port] = ep_np; > + > + found = true; > + } > + > + return found ? 0 : -ENODEV; > +} > + > +static void adv748x_dt_cleanup(struct adv748x_state *state) > +{ > + unsigned int i; > + > + for (i = 0; i < ADV748X_PORT_MAX; i++) > + of_node_put(state->endpoints[i]); > +} > + > +static int adv748x_setup_links(struct adv748x_state *state) > +{ > + int ret; > + int enabled = MEDIA_LNK_FL_ENABLED; > + > +/* > + * HACK/Workaround: > + * > + * Currently non-immutable link resets go through the RVin > + * driver, and cause the links to fail, due to not being part of RVIN. > + * As a temporary workaround until the RVIN driver knows better than to parse > + * links that do not belong to it, use static immutable links for our internal > + * media paths. > + */ > +#define ADV748x_DEV_STATIC_LINKS > +#ifdef ADV748x_DEV_STATIC_LINKS > + enabled |= MEDIA_LNK_FL_IMMUTABLE; > +#endif Has an RVIN patch fixing this been posted yet? If not, is anyone looking at that? Perhaps this should use #ifdef CONFIG_VIDEO_RCAR_VIN instead of inventing a define? > + > + /* TXA - Default link is with HDMI */ > + ret = media_create_pad_link(&state->hdmi.sd.entity, 1, > + &state->txa.sd.entity, 0, enabled); > + if (ret) { > + adv_err(state, "Failed to create HDMI-TXA pad link"); > + return ret; > + } > + > +#ifndef ADV748x_DEV_STATIC_LINKS > + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, > + &state->txa.sd.entity, 0, 0); > + if (ret) { > + adv_err(state, "Failed to create AFE-TXA pad link"); > + return ret; > + } > +#endif > + > + /* TXB - Can only output from the AFE */ > + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, > + &state->txb.sd.entity, 0, enabled); > + if (ret) { > + adv_err(state, "Failed to create AFE-TXB pad link"); > + return ret; > + } > + > + return 0; > +} > + > +int adv748x_register_subdevs(struct adv748x_state *state, > + struct v4l2_device *v4l2_dev) > +{ > + int ret; > + > + ret = v4l2_device_register_subdev(v4l2_dev, &state->hdmi.sd); > + if (ret < 0) > + return ret; > + > + ret = v4l2_device_register_subdev(v4l2_dev, &state->afe.sd); > + if (ret < 0) > + goto err_unregister_hdmi; > + > + ret = adv748x_setup_links(state); > + if (ret < 0) > + goto err_unregister_afe; > + > + return 0; > + > +err_unregister_afe: > + v4l2_device_unregister_subdev(&state->afe.sd); > +err_unregister_hdmi: > + v4l2_device_unregister_subdev(&state->hdmi.sd); > + > + return ret; > +} > + > +static int adv748x_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct adv748x_state *state; > + int ret; > + > + /* Check if the adapter supports the needed features */ > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) > + return -EIO; > + > + state = kzalloc(sizeof(struct adv748x_state), GFP_KERNEL); > + if (!state) > + return -ENOMEM; > + > + mutex_init(&state->mutex); > + > + state->dev = &client->dev; > + state->client = client; > + state->i2c_clients[ADV748X_PAGE_IO] = client; > + i2c_set_clientdata(client, state); > + > + /* Discover and process ports declared by the Device tree endpoints */ > + ret = adv748x_parse_dt(state); > + if (ret) { > + adv_err(state, "Failed to parse device tree"); > + goto err_free_mutex; > + } > + > + /* Configure IO Regmap region */ > + ret = adv748x_configure_regmap(state, ADV748X_PAGE_IO); > + if (ret) { > + adv_err(state, "Error configuring IO regmap region"); > + goto err_cleanup_dt; > + } > + > + ret = adv748x_identify_chip(state); > + if (ret) { > + adv_err(state, "Failed to identify chip"); > + goto err_cleanup_clients; > + } > + > + /* Configure remaining pages as I2C clients with regmap access */ > + ret = adv748x_initialise_clients(state); > + if (ret) { > + adv_err(state, "Failed to setup client regmap pages"); > + goto err_cleanup_clients; > + } > + > + /* SW reset ADV748X to its default values */ > + ret = adv748x_reset(state); > + if (ret) { > + adv_err(state, "Failed to reset hardware"); > + goto err_cleanup_clients; > + } > + > + /* Initialise HDMI */ > + ret = adv748x_hdmi_init(&state->hdmi); > + if (ret) { > + adv_err(state, "Failed to probe HDMI"); > + goto err_cleanup_clients; > + } > + > + /* Initialise AFE */ > + ret = adv748x_afe_init(&state->afe); > + if (ret) { > + adv_err(state, "Failed to probe AFE"); > + goto err_cleanup_hdmi; > + } > + > + /* Initialise TXA */ > + ret = adv748x_csi2_init(state, &state->txa); > + if (ret) { > + adv_err(state, "Failed to probe TXA"); > + goto err_cleanup_afe; > + } > + > + /* Initialise TXB */ > + ret = adv748x_csi2_init(state, &state->txb); > + if (ret) { > + adv_err(state, "Failed to probe TXB"); > + goto err_cleanup_txa; > + } > + > + return 0; > + > +err_cleanup_txa: > + adv748x_csi2_cleanup(&state->txa); > +err_cleanup_afe: > + adv748x_afe_cleanup(&state->afe); > +err_cleanup_hdmi: > + adv748x_hdmi_cleanup(&state->hdmi); > +err_cleanup_clients: > + adv748x_unregister_clients(state); > +err_cleanup_dt: > + adv748x_dt_cleanup(state); > +err_free_mutex: > + mutex_destroy(&state->mutex); > + kfree(state); > + > + return ret; > +} > + > +static int adv748x_remove(struct i2c_client *client) > +{ > + struct adv748x_state *state = i2c_get_clientdata(client); > + > + adv748x_afe_cleanup(&state->afe); > + adv748x_hdmi_cleanup(&state->hdmi); > + > + adv748x_csi2_cleanup(&state->txa); > + adv748x_csi2_cleanup(&state->txb); > + > + adv748x_unregister_clients(state); > + adv748x_dt_cleanup(state); > + mutex_destroy(&state->mutex); > + > + kfree(state); > + > + return 0; > +} > + > +static const struct i2c_device_id adv748x_id[] = { > + { "adv7481", 0 }, > + { "adv7482", 0 }, > + { }, > +}; > + > +static const struct of_device_id adv748x_of_table[] = { > + { .compatible = "adi,adv7481", }, > + { .compatible = "adi,adv7482", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, adv748x_of_table); > + > +static struct i2c_driver adv748x_driver = { > + .driver = { > + .name = "adv748x", > + .of_match_table = adv748x_of_table, > + }, > + .probe = adv748x_probe, > + .remove = adv748x_remove, > + .id_table = adv748x_id, > +}; > + > +module_i2c_driver(adv748x_driver); > + > +MODULE_AUTHOR("Kieran Bingham <kieran.bingham@ideasonboard.com>"); > +MODULE_DESCRIPTION("ADV748X video decoder"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/media/i2c/adv748x/adv748x-csi2.c b/drivers/media/i2c/adv748x/adv748x-csi2.c > new file mode 100644 > index 000000000000..a9b7fbd93530 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-csi2.c > @@ -0,0 +1,323 @@ > +/* > + * Driver for Analog Devices ADV748X CSI-2 Transmitter > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/module.h> > +#include <linux/mutex.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-ioctl.h> > + > +#include "adv748x.h" > + > +static bool is_txa(struct adv748x_csi2 *tx) > +{ > + return tx == &tx->state->txa; > +} > + > +static int adv748x_csi2_set_virtual_channel(struct adv748x_csi2 *tx, > + unsigned int vc) > +{ > + return tx_write(tx, ADV748X_CSI_VC_REF, vc << ADV748X_CSI_VC_REF_SHIFT); > +} > + > +/** > + * adv748x_csi2_register_link : Register and link internal entities > + * > + * @tx: CSI2 private entity > + * @v4l2_dev: Video registration device > + * @src: Source subdevice to establish link > + * @src_pad: Pad number of source to link to this @tx > + * @preferred: Specify if this link is preferred over pre-existing links > + * > + * Ensure that the subdevice is registered against the v4l2_device, and link the > + * source pad to the sink pad of the CSI2 bus entity. > + */ > +static int adv748x_csi2_register_link(struct adv748x_csi2 *tx, > + struct v4l2_device *v4l2_dev, > + struct v4l2_subdev *src, > + unsigned int src_pad, > + bool preferred) > +{ > + int enabled = 0; > + int ret; > + > + if (preferred) > + enabled = MEDIA_LNK_FL_ENABLED; > + > + if (!src->v4l2_dev) { > + ret = v4l2_device_register_subdev(v4l2_dev, src); > + if (ret) > + return ret; > + } > + > + return media_create_pad_link(&src->entity, src_pad, > + &tx->sd.entity, ADV748X_CSI2_SINK, > + enabled); > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_internal_ops > + * > + * We use the internal registered operation to be able to ensure that our > + * incremental subdevices (not connected in the forward path) can be registered > + * against the resulting video path and media device. > + */ > + > +static int adv748x_csi2_registered(struct v4l2_subdev *sd) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + int ret; > + > + adv_dbg(state, "Registered %s (%s)", is_txa(tx) ? "TXA":"TXB", > + sd->name); > + > + ret = adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->afe.sd, > + ADV748X_AFE_SOURCE, !is_txa(tx)); > + if (ret) > + return ret; > + > + /* TX-B only supports AFE */ > + if (!is_txa(tx)) > + return 0; > + > + return adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->hdmi.sd, > + ADV748X_HDMI_SOURCE, true); > +} > + > +static const struct v4l2_subdev_internal_ops adv748x_csi2_internal_ops = { > + .registered = adv748x_csi2_registered, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_csi2_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct v4l2_subdev *src; > + > + src = adv748x_get_remote_sd(&tx->pads[ADV748X_CSI2_SINK]); > + if (!src) > + return -EPIPE; > + > + return v4l2_subdev_call(src, video, s_stream, enable); > +} > + > +static const struct v4l2_subdev_video_ops adv748x_csi2_video_ops = { > + .s_stream = adv748x_csi2_s_stream, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + * > + * The CSI2 bus pads are ignorant to the data sizes or formats. > + * But we must support setting the pad formats for format propagation. > + */ > + > +static struct v4l2_mbus_framefmt * > +adv748x_csi2_get_pad_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + unsigned int pad, u32 which) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + > + if (which == V4L2_SUBDEV_FORMAT_TRY) > + return v4l2_subdev_get_try_format(sd, cfg, pad); > + else 'else' is not needed. > + return &tx->format; > +} > + > +static int adv748x_csi2_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + struct v4l2_mbus_framefmt *mbusformat; > + > + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, > + sdformat->which); > + if (!mbusformat) > + return -EINVAL; > + > + mutex_lock(&state->mutex); > + > + sdformat->format = *mbusformat; > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_csi2_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); > + struct adv748x_state *state = tx->state; > + struct v4l2_mbus_framefmt *mbusformat; > + int ret = 0; > + > + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, > + sdformat->which); > + if (!mbusformat) > + return -EINVAL; > + > + mutex_lock(&state->mutex); > + > + if (sdformat->pad == ADV748X_CSI2_SOURCE) { > + const struct v4l2_mbus_framefmt *sink_fmt; > + > + sink_fmt = adv748x_csi2_get_pad_format(sd, cfg, > + ADV748X_CSI2_SINK, > + sdformat->which); > + > + if (!sink_fmt) { > + ret = -EINVAL; > + goto unlock; > + } > + > + sdformat->format = *sink_fmt; > + } > + > + *mbusformat = sdformat->format; > + > +unlock: > + mutex_unlock(&state->mutex); > + > + return ret; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_csi2_pad_ops = { > + .get_fmt = adv748x_csi2_get_format, > + .set_fmt = adv748x_csi2_set_format, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_csi2_ops = { > + .video = &adv748x_csi2_video_ops, > + .pad = &adv748x_csi2_pad_ops, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Subdev module and controls > + */ > + > +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate) > +{ > + struct v4l2_ctrl *ctrl; > + > + ctrl = v4l2_ctrl_find(sd->ctrl_handler, V4L2_CID_PIXEL_RATE); > + if (!ctrl) > + return -EINVAL; > + > + return v4l2_ctrl_s_ctrl_int64(ctrl, rate); > +} > + > +static int adv748x_csi2_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + switch (ctrl->id) { > + case V4L2_CID_PIXEL_RATE: > + return 0; > + default: > + return -EINVAL; > + } > +} > + > +static const struct v4l2_ctrl_ops adv748x_csi2_ctrl_ops = { > + .s_ctrl = adv748x_csi2_s_ctrl, > +}; > + > +static int adv748x_csi2_init_controls(struct adv748x_csi2 *tx) > +{ > + struct v4l2_ctrl *ctrl; > + > + v4l2_ctrl_handler_init(&tx->ctrl_hdl, 1); > + > + ctrl = v4l2_ctrl_new_std(&tx->ctrl_hdl, &adv748x_csi2_ctrl_ops, > + V4L2_CID_PIXEL_RATE, 1, INT_MAX, 1, 1); > + > + tx->sd.ctrl_handler = &tx->ctrl_hdl; > + if (tx->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > + return tx->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&tx->ctrl_hdl); > +} > + > +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx) > +{ > + struct device_node *ep; > + int ret; > + > + /* We can not use container_of to get back to the state with two TXs */ > + tx->state = state; > + tx->page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB; > + > + ep = state->endpoints[is_txa(tx) ? ADV748X_PORT_TXA : ADV748X_PORT_TXB]; > + if (!ep) { > + adv_err(state, "No endpoint found for %s\n", > + is_txa(tx) ? "txa" : "txb"); > + return -ENODEV; > + } > + > + /* Initialise the virtual channel */ > + adv748x_csi2_set_virtual_channel(tx, 0); > + > + adv748x_subdev_init(&tx->sd, state, &adv748x_csi2_ops, > + MEDIA_ENT_F_UNKNOWN, > + is_txa(tx) ? "txa" : "txb"); > + > + /* Ensure that matching is based upon the endpoint fwnodes */ > + tx->sd.fwnode = of_fwnode_handle(ep); > + > + /* Register internal ops for incremental subdev registration */ > + tx->sd.internal_ops = &adv748x_csi2_internal_ops; > + > + tx->pads[ADV748X_CSI2_SINK].flags = MEDIA_PAD_FL_SINK; > + tx->pads[ADV748X_CSI2_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&tx->sd.entity, ADV748X_CSI2_NR_PADS, > + tx->pads); > + if (ret) > + return ret; > + > + ret = adv748x_csi2_init_controls(tx); > + if (ret) > + goto err_free_media; > + > + ret = v4l2_async_register_subdev(&tx->sd); > + if (ret) > + goto err_free_ctrl; > + > + return 0; > + > +err_free_ctrl: > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > +err_free_media: > + media_entity_cleanup(&tx->sd.entity); > + > + return ret; > +} > + > +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx) > +{ > + v4l2_async_unregister_subdev(&tx->sd); > + media_entity_cleanup(&tx->sd.entity); > + v4l2_ctrl_handler_free(&tx->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x-hdmi.c b/drivers/media/i2c/adv748x/adv748x-hdmi.c > new file mode 100644 > index 000000000000..8f02c851bbc0 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c > @@ -0,0 +1,652 @@ > +/* > + * Driver for Analog Devices ADV748X HDMI receiver and Component Processor (CP) > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + */ > + > +#include <linux/module.h> > +#include <linux/mutex.h> > + > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-dv-timings.h> > +#include <media/v4l2-ioctl.h> > + > +#include <uapi/linux/v4l2-dv-timings.h> > + > +#include "adv748x.h" > + > +/* ----------------------------------------------------------------------------- > + * HDMI and CP > + */ > + > +#define ADV748X_HDMI_MIN_WIDTH 640 > +#define ADV748X_HDMI_MAX_WIDTH 1920 > +#define ADV748X_HDMI_MIN_HEIGHT 480 > +#define ADV748X_HDMI_MAX_HEIGHT 1200 > +#define ADV748X_HDMI_MIN_PIXELCLOCK 0 /* unknown */ I wouldn't use 0 for the min pixelclock. Pick something like 13000000 instead (the lowest pixelclock rate for CEA timings, lowered by 0.5 MHz). > +#define ADV748X_HDMI_MAX_PIXELCLOCK 162000000 > + > +static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = { > + .type = V4L2_DV_BT_656_1120, > + /* keep this initialization for compatibility with GCC < 4.4.6 */ > + .reserved = { 0 }, > + /* Min pixelclock value is unknown */ > + V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH, > + ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT, > + ADV748X_HDMI_MIN_PIXELCLOCK, > + ADV748X_HDMI_MAX_PIXELCLOCK, > + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT, > + V4L2_DV_BT_CAP_INTERLACED | Has interlaced been tested? > + V4L2_DV_BT_CAP_PROGRESSIVE) > +}; > + > +struct adv748x_hdmi_video_standards { > + struct v4l2_dv_timings timings; > + u8 vid_std; > + u8 v_freq; > +}; > + > +static const struct adv748x_hdmi_video_standards > +adv748x_hdmi_video_standards[] = { > + { V4L2_DV_BT_CEA_720X480I59_94, 0x40, 0x00 }, > + { V4L2_DV_BT_CEA_720X576I50, 0x41, 0x01 }, > + { V4L2_DV_BT_CEA_720X480P59_94, 0x4a, 0x00 }, > + { V4L2_DV_BT_CEA_720X576P50, 0x4b, 0x00 }, > + { V4L2_DV_BT_CEA_1280X720P60, 0x53, 0x00 }, > + { V4L2_DV_BT_CEA_1280X720P50, 0x53, 0x01 }, > + { V4L2_DV_BT_CEA_1280X720P30, 0x53, 0x02 }, > + { V4L2_DV_BT_CEA_1280X720P25, 0x53, 0x03 }, > + { V4L2_DV_BT_CEA_1280X720P24, 0x53, 0x04 }, > + { V4L2_DV_BT_CEA_1920X1080I60, 0x54, 0x00 }, > + { V4L2_DV_BT_CEA_1920X1080I50, 0x54, 0x01 }, > + { V4L2_DV_BT_CEA_1920X1080P60, 0x5e, 0x00 }, > + { V4L2_DV_BT_CEA_1920X1080P50, 0x5e, 0x01 }, > + { V4L2_DV_BT_CEA_1920X1080P30, 0x5e, 0x02 }, > + { V4L2_DV_BT_CEA_1920X1080P25, 0x5e, 0x03 }, > + { V4L2_DV_BT_CEA_1920X1080P24, 0x5e, 0x04 }, > + /* SVGA */ > + { V4L2_DV_BT_DMT_800X600P56, 0x80, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P60, 0x81, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P72, 0x82, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P75, 0x83, 0x00 }, > + { V4L2_DV_BT_DMT_800X600P85, 0x84, 0x00 }, > + /* SXGA */ > + { V4L2_DV_BT_DMT_1280X1024P60, 0x85, 0x00 }, > + { V4L2_DV_BT_DMT_1280X1024P75, 0x86, 0x00 }, > + /* VGA */ > + { V4L2_DV_BT_DMT_640X480P60, 0x88, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P72, 0x89, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P75, 0x8a, 0x00 }, > + { V4L2_DV_BT_DMT_640X480P85, 0x8b, 0x00 }, > + /* XGA */ > + { V4L2_DV_BT_DMT_1024X768P60, 0x8c, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P70, 0x8d, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P75, 0x8e, 0x00 }, > + { V4L2_DV_BT_DMT_1024X768P85, 0x8f, 0x00 }, > + /* UXGA */ > + { V4L2_DV_BT_DMT_1600X1200P60, 0x96, 0x00 }, > +}; > + > +static void adv748x_hdmi_fill_format(struct adv748x_hdmi *hdmi, > + struct v4l2_mbus_framefmt *fmt) > +{ > + memset(fmt, 0, sizeof(*fmt)); > + > + fmt->code = MEDIA_BUS_FMT_RGB888_1X24; > + fmt->colorspace = V4L2_COLORSPACE_SRGB; It's OK for now, but the colorspace depends on the AVI InfoFrame contents. Add some comment stating this. > + fmt->field = hdmi->timings.bt.interlaced ? > + V4L2_FIELD_INTERLACED : V4L2_FIELD_NONE; > + > + fmt->width = hdmi->timings.bt.width; > + fmt->height = hdmi->timings.bt.height; > +} > + > +static void adv748x_fill_optional_dv_timings(struct v4l2_dv_timings *timings) > +{ > + v4l2_find_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, > + 250000, NULL, NULL); > +} > + > +static bool adv748x_hdmi_has_signal(struct adv748x_state *state) > +{ > + int val; > + > + /* Check that VERT_FILTER and DE_REGEN is locked */ > + val = hdmi_read(state, ADV748X_HDMI_LW1); > + return (val & ADV748X_HDMI_LW1_VERT_FILTER) && > + (val & ADV748X_HDMI_LW1_DE_REGEN); > +} > + > +static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state) > +{ > + int a, b; > + > + a = hdmi_read(state, ADV748X_HDMI_TMDS_1); > + b = hdmi_read(state, ADV748X_HDMI_TMDS_2); > + if (a < 0 || b < 0) > + return -ENODATA; > + > + /* > + * The High 9 bits store TMDS frequency measurement in MHz > + * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency > + * measurement in 1/128 MHz > + */ > + return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128; > +} > + > +/* > + * adv748x_hdmi_set_de_timings: Adjust horizontal picture offset through DE > + * > + * HDMI CP uses a Data Enable synchronisation timing reference > + * > + * Vary the leading and trailing edge position of the DE signal output by the CP > + * core. Values are stored as signed-twos-complement in one-pixel-clock units > + * > + * The start and end are shifted equally by the 10-bit shift value. > + */ > +static void adv748x_hdmi_set_de_timings(struct adv748x_state *state, int shift) > +{ > + u8 high, low; > + > + /* POS_HIGH stores bits 8 and 9 of both the start and end */ > + high = ADV748X_CP_DE_POS_HIGH_SET; > + high |= (shift & 0x300) >> 8; > + low = shift & 0xff; > + > + /* The sequence of the writes is important and must be followed */ > + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); > + cp_write(state, ADV748X_CP_DE_POS_END_LOW, low); > + > + high |= (shift & 0x300) >> 6; > + > + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); > + cp_write(state, ADV748X_CP_DE_POS_START_LOW, low); > +} > + > +static int adv748x_hdmi_set_video_timings(struct adv748x_state *state, > + const struct v4l2_dv_timings *timings) > +{ > + const struct adv748x_hdmi_video_standards *stds = > + adv748x_hdmi_video_standards; > + unsigned int i; > + > + for (i = 0; i < ARRAY_SIZE(adv748x_hdmi_video_standards); i++) { > + if (!v4l2_match_dv_timings(timings, &stds[i].timings, 250000, > + false)) > + continue; > + } > + > + if (i >= ARRAY_SIZE(adv748x_hdmi_video_standards)) > + return -EINVAL; > + > + /* > + * When setting cp_vid_std to either 720p, 1080i, or 1080p, the video > + * will get shifted horizontally to the left in active video mode. > + * The de_h_start and de_h_end controls are used to centre the picture > + * correctly > + */ > + switch (stds[i].vid_std) { > + case 0x53: /* 720p */ > + adv748x_hdmi_set_de_timings(state, -40); > + break; > + case 0x54: /* 1080i */ > + case 0x5e: /* 1080p */ > + adv748x_hdmi_set_de_timings(state, -44); > + break; > + default: > + adv748x_hdmi_set_de_timings(state, 0); > + break; > + } > + > + io_write(state, ADV748X_IO_VID_STD, stds[i].vid_std); > + io_clrset(state, ADV748X_IO_DATAPATH, ADV748X_IO_DATAPATH_VFREQ_M, > + stds[i].v_freq << ADV748X_IO_DATAPATH_VFREQ_SHIFT); > + > + return 0; > +} > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_video_ops > + */ > + > +static int adv748x_hdmi_s_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + > + if (!timings) > + return -EINVAL; > + > + if (v4l2_match_dv_timings(&hdmi->timings, timings, 0, false)) > + return 0; > + > + if (!v4l2_valid_dv_timings(timings, &adv748x_hdmi_timings_cap, > + NULL, NULL)) > + return -ERANGE; > + > + adv748x_fill_optional_dv_timings(timings); > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_hdmi_set_video_timings(state, timings); > + if (ret) > + goto error; > + > + hdmi->timings = *timings; > + > + cp_clrset(state, ADV748X_CP_VID_ADJ_2, ADV748X_CP_VID_ADJ_2_INTERLACED, > + timings->bt.interlaced ? > + ADV748X_CP_VID_ADJ_2_INTERLACED : 0); > + > + mutex_unlock(&state->mutex); > + > + return 0; > + > +error: > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + mutex_lock(&state->mutex); > + > + *timings = hdmi->timings; > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_dv_timings *timings) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + struct v4l2_bt_timings *bt = &timings->bt; > + int pixelclock; > + int polarity; > + > + if (!timings) > + return -EINVAL; > + > + memset(timings, 0, sizeof(struct v4l2_dv_timings)); > + > + if (!adv748x_hdmi_has_signal(state)) > + return -ENOLINK; > + > + pixelclock = adv748x_hdmi_read_pixelclock(state); > + if (pixelclock < 0) > + return -ENODATA; > + > + timings->type = V4L2_DV_BT_656_1120; > + > + bt->pixelclock = pixelclock; > + bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) & > + ADV748X_HDMI_F1H1_INTERLACED ? > + V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; > + bt->width = hdmi_read16(state, ADV748X_HDMI_LW1, > + ADV748X_HDMI_LW1_WIDTH_MASK); > + bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1, > + ADV748X_HDMI_F0H1_HEIGHT_MASK); > + bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH, > + ADV748X_HDMI_HFRONT_PORCH_MASK); > + bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH, > + ADV748X_HDMI_HSYNC_WIDTH_MASK); > + bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH, > + ADV748X_HDMI_HBACK_PORCH_MASK); > + bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH, > + ADV748X_HDMI_VFRONT_PORCH_MASK) / 2; > + bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH, > + ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2; > + bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH, > + ADV748X_HDMI_VBACK_PORCH_MASK) / 2; > + > + > + polarity = hdmi_read(state, 0x05); > + bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) | > + (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0); > + > + if (bt->interlaced == V4L2_DV_INTERLACED) { > + bt->height += hdmi_read16(state, 0x0b, 0x1fff); > + bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2; > + bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2; > + bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2; > + } > + > + adv748x_fill_optional_dv_timings(timings); > + > + /* > + * No interrupt handling is implemented yet. > + * There should be an IRQ when a cable is plugged and the new timings > + * should be figured out and stored to state. > + */ > + hdmi->timings = *timings; > + > + return 0; > +} > + > +static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + mutex_lock(&state->mutex); > + > + *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL; It would be nice if this could be a bit more detailed. Esp. being able to tell the difference between whether or not there is a signal, and whether or not the signal is stable (i.e. has sync). > + > + mutex_unlock(&state->mutex); > + > + return 0; > +} > + > +static int adv748x_hdmi_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + > + mutex_lock(&state->mutex); > + > + ret = adv748x_txa_power(state, enable); > + if (ret) > + goto done; > + > + if (adv748x_hdmi_has_signal(state)) > + adv_dbg(state, "Detected HDMI signal\n"); > + else > + adv_dbg(state, "Couldn't detect HDMI video signal\n"); > + > +done: > + mutex_unlock(&state->mutex); > + return ret; > +} > + > +static int adv748x_hdmi_g_pixelaspect(struct v4l2_subdev *sd, > + struct v4l2_fract *aspect) > +{ > + aspect->numerator = 1; > + aspect->denominator = 1; > + > + return 0; > +} > + > +static const struct v4l2_subdev_video_ops adv748x_video_ops_hdmi = { > + .s_dv_timings = adv748x_hdmi_s_dv_timings, > + .g_dv_timings = adv748x_hdmi_g_dv_timings, > + .query_dv_timings = adv748x_hdmi_query_dv_timings, > + .g_input_status = adv748x_hdmi_g_input_status, > + .s_stream = adv748x_hdmi_s_stream, > + .g_pixelaspect = adv748x_hdmi_g_pixelaspect, > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_pad_ops > + */ > + > +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) > +{ > + struct v4l2_subdev *tx; > + struct v4l2_dv_timings timings; > + struct v4l2_bt_timings *bt = &timings.bt; > + unsigned int fps; > + > + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); > + if (!tx) > + return -ENOLINK; > + > + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); > + > + fps = DIV_ROUND_CLOSEST(bt->pixelclock, > + V4L2_DV_BT_FRAME_WIDTH(bt) * > + V4L2_DV_BT_FRAME_HEIGHT(bt)); > + > + return adv748x_csi2_set_pixelrate(tx, bt->width * bt->height * fps); > +} > + > +static int adv748x_hdmi_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->index != 0) > + return -EINVAL; > + > + code->code = MEDIA_BUS_FMT_RGB888_1X24; > + > + return 0; > +} > + > +static int adv748x_hdmi_get_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); > + struct v4l2_mbus_framefmt *mbusformat; > + > + if (sdformat->pad != ADV748X_HDMI_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + sdformat->format = *mbusformat; > + } else { > + adv748x_hdmi_fill_format(hdmi, &sdformat->format); > + adv748x_hdmi_set_pixelrate(hdmi); > + } > + > + return 0; > +} > + > +static int adv748x_hdmi_set_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *sdformat) > +{ > + struct v4l2_mbus_framefmt *mbusformat; > + > + if (sdformat->pad != ADV748X_HDMI_SOURCE) > + return -EINVAL; > + > + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) > + return adv748x_hdmi_get_format(sd, cfg, sdformat); > + > + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); > + *mbusformat = sdformat->format; > + > + return 0; > +} > + > +static bool adv748x_hdmi_check_dv_timings(const struct v4l2_dv_timings *timings, > + void *hdl) > +{ > + const struct adv748x_hdmi_video_standards *stds = > + adv748x_hdmi_video_standards; > + unsigned int i; > + > + for (i = 0; stds[i].timings.bt.width; i++) > + if (v4l2_match_dv_timings(timings, &stds[i].timings, 0, false)) > + return true; > + > + return false; > +} > + > +static int adv748x_hdmi_enum_dv_timings(struct v4l2_subdev *sd, > + struct v4l2_enum_dv_timings *timings) > +{ > + return v4l2_enum_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, > + adv748x_hdmi_check_dv_timings, NULL); > +} > + > +static int adv748x_hdmi_dv_timings_cap(struct v4l2_subdev *sd, > + struct v4l2_dv_timings_cap *cap) > +{ > + *cap = adv748x_hdmi_timings_cap; > + return 0; > +} > + > +static const struct v4l2_subdev_pad_ops adv748x_pad_ops_hdmi = { > + .enum_mbus_code = adv748x_hdmi_enum_mbus_code, > + .set_fmt = adv748x_hdmi_set_format, > + .get_fmt = adv748x_hdmi_get_format, > + .dv_timings_cap = adv748x_hdmi_dv_timings_cap, > + .enum_dv_timings = adv748x_hdmi_enum_dv_timings, No get/set_edid ops? How can you use HDMI without having these ops? > +}; > + > +/* ----------------------------------------------------------------------------- > + * v4l2_subdev_ops > + */ > + > +static const struct v4l2_subdev_ops adv748x_ops_hdmi = { > + .video = &adv748x_video_ops_hdmi, > + .pad = &adv748x_pad_ops_hdmi, > +}; > + > +/* ----------------------------------------------------------------------------- > + * Controls > + */ > + > +static const char * const hdmi_ctrl_patgen_menu[] = { > + "Disabled", > + "Plain Blue", I'd say just "Blue" or possibly "Solid Blue". > + "Color Bars", > + "Ramp Grey", > + "Ramp Blue", > + "Ramp Red", > + "Checkered" I assume this is a black and white pattern? If so, say: "B&W Checkered" > +}; > + > +static int adv748x_hdmi_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct adv748x_hdmi *hdmi = adv748x_ctrl_to_hdmi(ctrl); > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + int ret; > + u8 pattern; > + > + /* Enable video adjustment first */ > + ret = cp_clrset(state, ADV748X_CP_VID_ADJ, > + ADV748X_CP_VID_ADJ_ENABLE, > + ADV748X_CP_VID_ADJ_ENABLE); > + if (ret < 0) > + return ret; > + > + switch (ctrl->id) { > + case V4L2_CID_BRIGHTNESS: > + ret = cp_write(state, ADV748X_CP_BRI, ctrl->val); > + break; > + case V4L2_CID_HUE: > + ret = cp_write(state, ADV748X_CP_HUE, ctrl->val); > + break; > + case V4L2_CID_CONTRAST: > + ret = cp_write(state, ADV748X_CP_CON, ctrl->val); > + break; > + case V4L2_CID_SATURATION: > + ret = cp_write(state, ADV748X_CP_SAT, ctrl->val); > + break; > + case V4L2_CID_TEST_PATTERN: > + pattern = ctrl->val; > + > + /* Pattern is 0-indexed. Ctrl Menu is 1-indexed */ > + if (pattern) { > + pattern--; > + pattern |= ADV748X_CP_PAT_GEN_EN; > + } > + > + ret = cp_write(state, ADV748X_CP_PAT_GEN, pattern); > + > + break; > + default: > + return -EINVAL; > + } > + > + return ret; > +} > + > +static const struct v4l2_ctrl_ops adv748x_hdmi_ctrl_ops = { > + .s_ctrl = adv748x_hdmi_s_ctrl, > +}; > + > +static int adv748x_hdmi_init_controls(struct adv748x_hdmi *hdmi) > +{ > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + > + v4l2_ctrl_handler_init(&hdmi->ctrl_hdl, 5); > + > + /* Use our mutex for the controls */ > + hdmi->ctrl_hdl.lock = &state->mutex; > + > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_BRIGHTNESS, ADV748X_CP_BRI_MIN, > + ADV748X_CP_BRI_MAX, 1, ADV748X_CP_BRI_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_CONTRAST, ADV748X_CP_CON_MIN, > + ADV748X_CP_CON_MAX, 1, ADV748X_CP_CON_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_SATURATION, ADV748X_CP_SAT_MIN, > + ADV748X_CP_SAT_MAX, 1, ADV748X_CP_SAT_DEF); > + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_HUE, ADV748X_CP_HUE_MIN, > + ADV748X_CP_HUE_MAX, 1, ADV748X_CP_HUE_DEF); You should implement the V4L2_CID_DV_RX_POWER_PRESENT control as well, once interrupts are working. Perhaps add a comment as a reminder? > + > + v4l2_ctrl_new_std_menu_items(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(hdmi_ctrl_patgen_menu) - 1, > + 0, 0, hdmi_ctrl_patgen_menu); > + > + hdmi->sd.ctrl_handler = &hdmi->ctrl_hdl; > + if (hdmi->ctrl_hdl.error) { > + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); > + return hdmi->ctrl_hdl.error; > + } > + > + return v4l2_ctrl_handler_setup(&hdmi->ctrl_hdl); > +} > + > +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi) > +{ > + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); > + static const struct v4l2_dv_timings cea720x480 = > + V4L2_DV_BT_CEA_720X480I59_94; > + int ret; > + > + hdmi->timings = cea720x480; > + > + adv748x_subdev_init(&hdmi->sd, state, &adv748x_ops_hdmi, > + MEDIA_ENT_F_IO_DTV, "hdmi"); > + > + hdmi->pads[ADV748X_HDMI_SINK].flags = MEDIA_PAD_FL_SINK; > + hdmi->pads[ADV748X_HDMI_SOURCE].flags = MEDIA_PAD_FL_SOURCE; > + > + ret = media_entity_pads_init(&hdmi->sd.entity, > + ADV748X_HDMI_NR_PADS, hdmi->pads); > + if (ret) > + return ret; > + > + ret = adv748x_hdmi_init_controls(hdmi); > + if (ret) > + goto err_free_media; > + > + return 0; > + > +err_free_media: > + media_entity_cleanup(&hdmi->sd.entity); > + > + return ret; > +} > + > +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi) > +{ > + v4l2_device_unregister_subdev(&hdmi->sd); > + media_entity_cleanup(&hdmi->sd.entity); > + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); > +} > diff --git a/drivers/media/i2c/adv748x/adv748x.h b/drivers/media/i2c/adv748x/adv748x.h > new file mode 100644 > index 000000000000..2f36e5052f08 > --- /dev/null > +++ b/drivers/media/i2c/adv748x/adv748x.h > @@ -0,0 +1,415 @@ > +/* > + * Driver for Analog Devices ADV748X video decoder and HDMI receiver > + * > + * Copyright (C) 2017 Renesas Electronics Corp. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + * > + * Authors: > + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> > + * Niklas Söderlund <niklas.soderlund@ragnatech.se> > + * Kieran Bingham <kieran.bingham@ideasonboard.com> > + * > + * The ADV748x range of receivers have the following configurations: > + * > + * Analog HDMI MHL 4-Lane 1-Lane > + * In In CSI CSI > + * ADV7480 X X X > + * ADV7481 X X X X X > + * ADV7482 X X X X > + */ > + > +#include <linux/i2c.h> > + > +#ifndef _ADV748X_H_ > +#define _ADV748X_H_ > + > +/* I2C slave addresses */ > +#define ADV748X_I2C_IO 0x70 /* IO Map */ > +#define ADV748X_I2C_DPLL 0x26 /* DPLL Map */ > +#define ADV748X_I2C_CP 0x22 /* CP Map */ > +#define ADV748X_I2C_HDMI 0x34 /* HDMI Map */ > +#define ADV748X_I2C_EDID 0x36 /* EDID Map */ > +#define ADV748X_I2C_REPEATER 0x32 /* HDMI RX Repeater Map */ > +#define ADV748X_I2C_INFOFRAME 0x31 /* HDMI RX InfoFrame Map */ > +#define ADV748X_I2C_CEC 0x41 /* CEC Map */ > +#define ADV748X_I2C_SDP 0x79 /* SDP Map */ > +#define ADV748X_I2C_TXB 0x48 /* CSI-TXB Map */ > +#define ADV748X_I2C_TXA 0x4a /* CSI-TXA Map */ > + > +enum adv748x_page { > + ADV748X_PAGE_IO, > + ADV748X_PAGE_DPLL, > + ADV748X_PAGE_CP, > + ADV748X_PAGE_HDMI, > + ADV748X_PAGE_EDID, > + ADV748X_PAGE_REPEATER, > + ADV748X_PAGE_INFOFRAME, > + ADV748X_PAGE_CEC, > + ADV748X_PAGE_SDP, > + ADV748X_PAGE_TXB, > + ADV748X_PAGE_TXA, > + ADV748X_PAGE_MAX, > + > + /* Fake pages for register sequences */ > + ADV748X_PAGE_WAIT, /* Wait x msec */ > + ADV748X_PAGE_EOR, /* End Mark */ > +}; > + > +/** > + * enum adv748x_ports - Device tree port number definitions > + * > + * The ADV748X ports define the mapping between subdevices > + * and the device tree specification > + */ > +enum adv748x_ports { > + ADV748X_PORT_AIN0 = 0, > + ADV748X_PORT_AIN1 = 1, > + ADV748X_PORT_AIN2 = 2, > + ADV748X_PORT_AIN3 = 3, > + ADV748X_PORT_AIN4 = 4, > + ADV748X_PORT_AIN5 = 5, > + ADV748X_PORT_AIN6 = 6, > + ADV748X_PORT_AIN7 = 7, > + ADV748X_PORT_HDMI = 8, > + ADV748X_PORT_TTL = 9, > + ADV748X_PORT_TXA = 10, > + ADV748X_PORT_TXB = 11, > + ADV748X_PORT_MAX = 12, > +}; > + > +enum adv748x_csi2_pads { > + ADV748X_CSI2_SINK, > + ADV748X_CSI2_SOURCE, > + ADV748X_CSI2_NR_PADS, > +}; > + > +/* CSI2 transmitters can have 2 internal connections, HDMI/AFE */ > +#define ADV748X_CSI2_MAX_SUBDEVS 2 > + > +struct adv748x_csi2 { > + struct adv748x_state *state; > + struct v4l2_mbus_framefmt format; > + unsigned int page; > + > + struct media_pad pads[ADV748X_CSI2_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > +}; > + > +#define notifier_to_csi2(n) container_of(n, struct adv748x_csi2, notifier) > +#define adv748x_sd_to_csi2(sd) container_of(sd, struct adv748x_csi2, sd) > + > +enum adv748x_hdmi_pads { > + ADV748X_HDMI_SINK, > + ADV748X_HDMI_SOURCE, > + ADV748X_HDMI_NR_PADS, > +}; > + > +struct adv748x_hdmi { > + struct media_pad pads[ADV748X_HDMI_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > + struct v4l2_mbus_framefmt format; > + > + struct v4l2_dv_timings timings; > +}; > + > +#define adv748x_ctrl_to_hdmi(ctrl) \ > + container_of(ctrl->handler, struct adv748x_hdmi, ctrl_hdl) > +#define adv748x_sd_to_hdmi(sd) container_of(sd, struct adv748x_hdmi, sd) > + > +enum adv748x_afe_pads { > + ADV748X_AFE_SINK_AIN0, > + ADV748X_AFE_SINK_AIN1, > + ADV748X_AFE_SINK_AIN2, > + ADV748X_AFE_SINK_AIN3, > + ADV748X_AFE_SINK_AIN4, > + ADV748X_AFE_SINK_AIN5, > + ADV748X_AFE_SINK_AIN6, > + ADV748X_AFE_SINK_AIN7, > + ADV748X_AFE_SOURCE, > + ADV748X_AFE_NR_PADS, > +}; > + > +struct adv748x_afe { > + struct media_pad pads[ADV748X_AFE_NR_PADS]; > + struct v4l2_ctrl_handler ctrl_hdl; > + struct v4l2_subdev sd; > + struct v4l2_mbus_framefmt format; > + > + bool streaming; > + v4l2_std_id curr_norm; > + unsigned int input; > +}; > + > +#define adv748x_ctrl_to_afe(ctrl) \ > + container_of(ctrl->handler, struct adv748x_afe, ctrl_hdl) > +#define adv748x_sd_to_afe(sd) container_of(sd, struct adv748x_afe, sd) > + > +/** > + * struct adv748x_state - State of ADV748X > + * @dev: (OF) device > + * @client: I2C client > + * @mutex: protect global state > + * > + * @endpoints: parsed device node endpoints for each port > + * > + * @i2c_addresses I2C Page addresses > + * @i2c_clients I2C clients for the page accesses > + * @regmap regmap configuration pages. > + * > + * @hdmi: state of HDMI receiver context > + * @afe: state of AFE receiver context > + * @txa: state of TXA transmitter context > + * @txb: state of TXB transmitter context > + */ > +struct adv748x_state { > + struct device *dev; > + struct i2c_client *client; > + struct mutex mutex; > + > + struct device_node *endpoints[ADV748X_PORT_MAX]; > + > + struct i2c_client *i2c_clients[ADV748X_PAGE_MAX]; > + struct regmap *regmap[ADV748X_PAGE_MAX]; > + > + struct adv748x_hdmi hdmi; > + struct adv748x_afe afe; > + struct adv748x_csi2 txa; > + struct adv748x_csi2 txb; > +}; > + > +#define adv748x_hdmi_to_state(h) container_of(h, struct adv748x_state, hdmi) > +#define adv748x_afe_to_state(a) container_of(a, struct adv748x_state, afe) > + > +#define adv_err(a, fmt, arg...) dev_err(a->dev, fmt, ##arg) > +#define adv_info(a, fmt, arg...) dev_info(a->dev, fmt, ##arg) > +#define adv_dbg(a, fmt, arg...) dev_dbg(a->dev, fmt, ##arg) > + > +/* Register Mappings */ > + > +/* IO Map */ > +#define ADV748X_IO_PD 0x00 /* power down controls */ > +#define ADV748X_IO_PD_RX_EN BIT(6) > + > +#define ADV748X_IO_REG_04 0x04 > +#define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */ > + > +#define ADV748X_IO_DATAPATH 0x03 /* datapath cntrl */ > +#define ADV748X_IO_DATAPATH_VFREQ_M 0x70 > +#define ADV748X_IO_DATAPATH_VFREQ_SHIFT 4 > + > +#define ADV748X_IO_VID_STD 0x05 > + > +#define ADV748X_IO_10 0x10 /* io_reg_10 */ > +#define ADV748X_IO_10_CSI4_EN BIT(7) > +#define ADV748X_IO_10_CSI1_EN BIT(6) > +#define ADV748X_IO_10_PIX_OUT_EN BIT(5) > + > +#define ADV748X_IO_CHIP_REV_ID_1 0xdf > +#define ADV748X_IO_CHIP_REV_ID_2 0xe0 > + > +#define ADV748X_IO_SLAVE_ADDR_BASE 0xf2 > + > +/* HDMI RX Map */ > +#define ADV748X_HDMI_LW1 0x07 /* line width_1 */ > +#define ADV748X_HDMI_LW1_VERT_FILTER BIT(7) > +#define ADV748X_HDMI_LW1_DE_REGEN BIT(5) > +#define ADV748X_HDMI_LW1_WIDTH_MASK 0x1fff > + > +#define ADV748X_HDMI_F0H1 0x09 /* field0 height_1 */ > +#define ADV748X_HDMI_F0H1_HEIGHT_MASK 0x1fff > + > +#define ADV748X_HDMI_F1H1 0x0b /* field1 height_1 */ > +#define ADV748X_HDMI_F1H1_INTERLACED BIT(5) > + > +#define ADV748X_HDMI_HFRONT_PORCH 0x20 /* hsync_front_porch_1 */ > +#define ADV748X_HDMI_HFRONT_PORCH_MASK 0x1fff > + > +#define ADV748X_HDMI_HSYNC_WIDTH 0x22 /* hsync_pulse_width_1 */ > +#define ADV748X_HDMI_HSYNC_WIDTH_MASK 0x1fff > + > +#define ADV748X_HDMI_HBACK_PORCH 0x24 /* hsync_back_porch_1 */ > +#define ADV748X_HDMI_HBACK_PORCH_MASK 0x1fff > + > +#define ADV748X_HDMI_VFRONT_PORCH 0x2a /* field0_vs_front_porch_1 */ > +#define ADV748X_HDMI_VFRONT_PORCH_MASK 0x3fff > + > +#define ADV748X_HDMI_VSYNC_WIDTH 0x2e /* field0_vs_pulse_width_1 */ > +#define ADV748X_HDMI_VSYNC_WIDTH_MASK 0x3fff > + > +#define ADV748X_HDMI_VBACK_PORCH 0x32 /* field0_vs_back_porch_1 */ > +#define ADV748X_HDMI_VBACK_PORCH_MASK 0x3fff > + > +#define ADV748X_HDMI_TMDS_1 0x51 /* hdmi_reg_51 */ > +#define ADV748X_HDMI_TMDS_2 0x52 /* hdmi_reg_52 */ > + > +/* SDP Main Map */ > +#define ADV748X_SDP_INSEL 0x00 /* user_map_rw_reg_00 */ > + > +#define ADV748X_SDP_VID_SEL 0x02 /* user_map_rw_reg_02 */ > +#define ADV748X_SDP_VID_SEL_MASK 0xf0 > +#define ADV748X_SDP_VID_SEL_SHIFT 4 > + > +/* Contrast - Unsigned*/ > +#define ADV748X_SDP_CON 0x08 /* user_map_rw_reg_08 */ > +#define ADV748X_SDP_CON_MIN 0 > +#define ADV748X_SDP_CON_DEF 128 > +#define ADV748X_SDP_CON_MAX 255 > + > +/* Brightness - Signed */ > +#define ADV748X_SDP_BRI 0x0a /* user_map_rw_reg_0a */ > +#define ADV748X_SDP_BRI_MIN -128 > +#define ADV748X_SDP_BRI_DEF 0 > +#define ADV748X_SDP_BRI_MAX 127 > + > +/* Hue - Signed, inverted*/ > +#define ADV748X_SDP_HUE 0x0b /* user_map_rw_reg_0b */ > +#define ADV748X_SDP_HUE_MIN -127 > +#define ADV748X_SDP_HUE_DEF 0 > +#define ADV748X_SDP_HUE_MAX 128 > + > +/* Test Patterns / Default Values */ > +#define ADV748X_SDP_DEF 0x0c /* user_map_rw_reg_0c */ > +#define ADV748X_SDP_DEF_VAL_EN BIT(0) /* Force free run mode */ > +#define ADV748X_SDP_DEF_VAL_AUTO_EN BIT(1) /* Free run when no signal */ > + > +#define ADV748X_SDP_MAP_SEL 0x0e /* user_map_rw_reg_0e */ > +#define ADV748X_SDP_MAP_SEL_RO_MAIN 1 > + > +/* Free run pattern select */ > +#define ADV748X_SDP_FRP 0x14 > +#define ADV748X_SDP_FRP_MASK GENMASK(3, 1) > + > +/* Saturation */ > +#define ADV748X_SDP_SD_SAT_U 0xe3 /* user_map_rw_reg_e3 */ > +#define ADV748X_SDP_SD_SAT_V 0xe4 /* user_map_rw_reg_e4 */ > +#define ADV748X_SDP_SAT_MIN 0 > +#define ADV748X_SDP_SAT_DEF 128 > +#define ADV748X_SDP_SAT_MAX 255 > + > +/* SDP RO Main Map */ > +#define ADV748X_SDP_RO_10 0x10 > +#define ADV748X_SDP_RO_10_IN_LOCK BIT(0) > + > +/* CP Map */ > +#define ADV748X_CP_PAT_GEN 0x37 /* int_pat_gen_1 */ > +#define ADV748X_CP_PAT_GEN_EN BIT(7) > + > +/* Contrast Control - Unsigned */ > +#define ADV748X_CP_CON 0x3a /* contrast_cntrl */ > +#define ADV748X_CP_CON_MIN 0 /* Minimum contrast */ > +#define ADV748X_CP_CON_DEF 128 /* Default */ > +#define ADV748X_CP_CON_MAX 255 /* Maximum contrast */ > + > +/* Saturation Control - Unsigned */ > +#define ADV748X_CP_SAT 0x3b /* saturation_cntrl */ > +#define ADV748X_CP_SAT_MIN 0 /* Minimum saturation */ > +#define ADV748X_CP_SAT_DEF 128 /* Default */ > +#define ADV748X_CP_SAT_MAX 255 /* Maximum saturation */ > + > +/* Brightness Control - Signed */ > +#define ADV748X_CP_BRI 0x3c /* brightness_cntrl */ > +#define ADV748X_CP_BRI_MIN -128 /* Luma is -512d */ > +#define ADV748X_CP_BRI_DEF 0 /* Luma is 0 */ > +#define ADV748X_CP_BRI_MAX 127 /* Luma is 508d */ > + > +/* Hue Control */ > +#define ADV748X_CP_HUE 0x3d /* hue_cntrl */ > +#define ADV748X_CP_HUE_MIN 0 /* -90 degree */ > +#define ADV748X_CP_HUE_DEF 0 /* -90 degree */ > +#define ADV748X_CP_HUE_MAX 255 /* +90 degree */ > + > +#define ADV748X_CP_VID_ADJ 0x3e /* vid_adj_0 */ > +#define ADV748X_CP_VID_ADJ_ENABLE BIT(7) /* Enable colour controls */ > + > +#define ADV748X_CP_DE_POS_HIGH 0x8b /* de_pos_adj_6 */ > +#define ADV748X_CP_DE_POS_HIGH_SET BIT(6) > +#define ADV748X_CP_DE_POS_END_LOW 0x8c /* de_pos_adj_7 */ > +#define ADV748X_CP_DE_POS_START_LOW 0x8d /* de_pos_adj_8 */ > + > +#define ADV748X_CP_VID_ADJ_2 0x91 > +#define ADV748X_CP_VID_ADJ_2_INTERLACED BIT(6) > +#define ADV748X_CP_VID_ADJ_2_INTERLACED_3D BIT(4) > + > +#define ADV748X_CP_CLMP_POS 0xc9 /* clmp_pos_cntrl_4 */ > +#define ADV748X_CP_CLMP_POS_DIS_AUTO BIT(0) /* dis_auto_param_buff */ > + > +/* CSI : TXA/TXB Maps */ > +#define ADV748X_CSI_VC_REF 0x0d /* csi_tx_top_reg_0d */ > +#define ADV748X_CSI_VC_REF_SHIFT 6 > + > +#define ADV748X_CSI_FS_AS_LS 0x1e /* csi_tx_top_reg_1e */ > +#define ADV748X_CSI_FS_AS_LS_UNKNOWN BIT(6) /* Undocumented bit */ > + > +/* Register handling */ > + > +int adv748x_read(struct adv748x_state *state, u8 addr, u8 reg); > +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value); > +int adv748x_write_block(struct adv748x_state *state, int client_page, > + unsigned int init_reg, const void *val, > + size_t val_len); > + > +#define io_read(s, r) adv748x_read(s, ADV748X_PAGE_IO, r) > +#define io_write(s, r, v) adv748x_write(s, ADV748X_PAGE_IO, r, v) > +#define io_clrset(s, r, m, v) io_write(s, r, (io_read(s, r) & ~m) | v) > + > +#define hdmi_read(s, r) adv748x_read(s, ADV748X_PAGE_HDMI, r) > +#define hdmi_read16(s, r, m) (((hdmi_read(s, r) << 8) | hdmi_read(s, r+1)) & m) > +#define hdmi_write(s, r, v) adv748x_write(s, ADV748X_PAGE_HDMI, r, v) > +#define hdmi_clrset(s, r, m, v) hdmi_write(s, r, (hdmi_read(s, r) & ~m) | v) > + > +#define sdp_read(s, r) adv748x_read(s, ADV748X_PAGE_SDP, r) > +#define sdp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_SDP, r, v) > +#define sdp_clrset(s, r, m, v) sdp_write(s, r, (sdp_read(s, r) & ~m) | v) > + > +#define cp_read(s, r) adv748x_read(s, ADV748X_PAGE_CP, r) > +#define cp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_CP, r, v) > +#define cp_clrset(s, r, m, v) cp_write(s, r, (cp_read(s, r) & ~m) | v) > + > +#define txa_read(s, r) adv748x_read(s, ADV748X_PAGE_TXA, r) > +#define txa_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXA, r, v) > +#define txa_clrset(s, r, m, v) txa_write(s, r, (txa_read(s, r) & ~m) | v) > + > +#define txb_read(s, r) adv748x_read(s, ADV748X_PAGE_TXB, r) > +#define txb_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXB, r, v) > +#define txb_clrset(s, r, m, v) txb_write(s, r, (txb_read(s, r) & ~m) | v) > + > +#define tx_read(t, r) adv748x_read(t->state, t->page, r) > +#define tx_write(t, r, v) adv748x_write(t->state, t->page, r, v) > +#define tx_clrset(t, r, m, v) tx_write(t, r, (tx_read(t, r) & ~m) | v) > + > +static inline struct v4l2_subdev *adv748x_get_remote_sd(struct media_pad *pad) > +{ > + pad = media_entity_remote_pad(pad); > + if (!pad) > + return NULL; > + > + return media_entity_to_v4l2_subdev(pad->entity); > +} > + > +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, > + const struct v4l2_subdev_ops *ops, u32 function, > + const char *ident); > + > +int adv748x_register_subdevs(struct adv748x_state *state, > + struct v4l2_device *v4l2_dev); > + > +int adv748x_txa_power(struct adv748x_state *state, bool on); > +int adv748x_txb_power(struct adv748x_state *state, bool on); > + > +int adv748x_afe_init(struct adv748x_afe *afe); > +void adv748x_afe_cleanup(struct adv748x_afe *afe); > + > +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx); > +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx); > +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate); > + > +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi); > +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi); > + > +#endif /* _ADV748X_H_ */ > Regards, Hans
Hi Hans, Thankyou for your review, and apologies for the delay - I was OoO last week. On 19/06/17 10:13, Hans Verkuil wrote: > On 06/13/2017 02:35 AM, Kieran Bingham wrote: >> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> >> Provide support for the ADV7481 and ADV7482. >> >> The driver is modelled with 4 subdevices to allow simultaneous streaming >> from the AFE (Analog front end) and HDMI inputs though two CSI TX >> entities. >> >> The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked >> to the TXB CSI bus. >> >> The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, >> and an earlier rework by Niklas Söderlund. >> >> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> >> --- >> >> v2: >> - Implement DT parsing >> - adv748x: Add CSI2 entity >> - adv748x: Rework pad allocations and fmts >> - Give AFE 8 input pads and move pad defines >> - Use the enums to ensure pads are referenced correctly. >> - adv748x: Rename AFE/HDMI entities >> Now they are 'just afe' and 'just hdmi' >> - Reorder the entity enum and structures >> - Added pad-format for the CSI2 entities >> - CSI2 s_stream pass through >> - CSI2 control pass through (with link following) >> >> v3: >> - dt: Extend DT documentation to specify interrupt mappings >> - simplify adv748x_parse_dt >> - core: Add banner to header file describing ADV748x variants >> - Use entity structure pointers rather than global state pointers where >> possible >> - afe: Reduce indent on afe_status >> - hdmi: Add error checking to the bt->pixelclock values. >> - Remove all unnecessary pad checks: handled by core >> - Fix all probe cleanup paths >> - adv748x_csi2_probe() now fails if it has no endpoint >> - csi2: Fix small oneliners for is_txa and get_remote_sd() >> - csi2: Fix checkpatch warnings >> - csi2: Fix up s_stream pass-through >> - csi2: Fix up Pixel Rate passthrough >> - csi2: simplify adv748x_csi2_get_pad_format() >> - Remove 'async notifiers' from AFE/HDMI >> Using async notifiers was overkill, when we have access to the >> subdevices internally and can register them directly. >> - Use state lock in control handlers and clean up s_ctrls >> - remove _interruptible mutex locks >> >> v4: >> - all: Convert hex 0xXX to lowercase >> - all: Use defines instead of hardcoded register values >> - all: Use regmap >> - afe, csi2, hdmi: _probe -> _init >> - afe, csi2, hdmi: _remove -> _cleanup >> - afe, hdmi: Convert pattern generator to a control >> - afe, hdmi: get/set-fmt refactor >> - afe, hdmi, csi2: Convert to internal calls for pixelrate >> - afe: Allow the AFE to configure the Input Select from DT >> - afe: Reduce indent on adv748x_afe_status switch >> - afe: Remove ununsed macro definitions AIN0-7 >> - afe: Remove extraneous control checks handled by core >> - afe: Comment fixups >> - afe: Rename error label >> - afe: Correct control names on the SDP >> - afe: Use AIN0-7 rather than AIN1-8 to match ports and MC pads >> - core: adv748x_parse_dt references to nodes, and catch multiple >> endpoints in a port. >> - core: adv748x_dt_cleanup to simplify releasing DT nodes >> - core: adv748x_print_info renamed to adv748x_identify_chip >> - core: reorganise ordering of probe sequence >> - core: No need for of_match_ptr >> - core: Fix up i2c read/writes (regmap still on todo list) >> - core: Set specific functions from the entities on subdev-init >> - core: Use kzalloc for state instead of devm >> - core: Improve probe error reporting >> - core: Track unknown BIT(6) in tx{a,b}_power >> - csi2: Improve adv748x_csi2_get_remote_sd as adv748x_csi2_get_source_sd >> - csi2: -EPIPE instead of -ENODEV >> - csi2: adv_dbg, instead of adv_info >> - csi2: adv748x_csi2_set_format fix >> - csi2: remove async notifier and sd member variables >> - csi2: register links from the CSI2 >> - csi2: create virtual channel helper function >> - dt: Remove numbering from endpoints >> - dt: describe ports and interrupts as optional >> - dt: Re-tab >> - hdmi: adv748x_hdmi_have_signal -> adv748x_hdmi_has_signal >> - hdmi: fix adv748x_hdmi_read_pixelclock return checks >> - hdmi: improve adv748x_hdmi_set_video_timings >> - hdmi: Fix tmp variable as polarity >> - hdmi: Improve adv748x_hdmi_s_stream >> - hdmi: Clean up adv748x_hdmi_s_ctrl register definitions and usage >> - hdmi: Fix up adv748x_hdmi_s_dv_timings with macro names for register >> - hdmi: Add locking to adv748x_hdmi_g_dv_timings >> writes and locking >> - hdmi: adv748x_hdmi_set_de_timings function added to clarify DE writes >> - hdmi: Use CP in control register naming to match component processor >> - hdmi: clean up adv748x_hdmi_query_dv_timings() >> - KConfig: Fix up dependency and capitalisation >> >> >> Documentation/devicetree/bindings/media/i2c/adv748x.txt | 96 +- > > This should be a separate patch cross posted to the devicetree mailinglist. > >> MAINTAINERS | 6 +- > > This should also be a separate patch. > >> drivers/media/i2c/Kconfig | 11 +- >> drivers/media/i2c/Makefile | 1 +- >> drivers/media/i2c/adv748x/Makefile | 7 +- >> drivers/media/i2c/adv748x/adv748x-afe.c | 571 ++++++- >> drivers/media/i2c/adv748x/adv748x-core.c | 907 +++++++++- >> drivers/media/i2c/adv748x/adv748x-csi2.c | 323 +++- >> drivers/media/i2c/adv748x/adv748x-hdmi.c | 652 ++++++- >> drivers/media/i2c/adv748x/adv748x.h | 415 ++++- >> 10 files changed, 2989 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/i2c/adv748x.txt >> create mode 100644 drivers/media/i2c/adv748x/Makefile >> create mode 100644 drivers/media/i2c/adv748x/adv748x-afe.c >> create mode 100644 drivers/media/i2c/adv748x/adv748x-core.c >> create mode 100644 drivers/media/i2c/adv748x/adv748x-csi2.c >> create mode 100644 drivers/media/i2c/adv748x/adv748x-hdmi.c >> create mode 100644 drivers/media/i2c/adv748x/adv748x.h >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt >> b/Documentation/devicetree/bindings/media/i2c/adv748x.txt >> new file mode 100644 >> index 000000000000..b17f8983c992 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt >> @@ -0,0 +1,96 @@ >> +* Analog Devices ADV748X video decoder with HDMI receiver >> + > +The ADV7481, and ADV7482 are multi format video decoders with an integrated > > No comma needed. Fixed, > >> +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB >> +from three input sources HDMI, analog and TTL. >> + >> +Required Properties: >> + >> + - compatible: Must contain one of the following >> + - "adi,adv7481" for the ADV7481 >> + - "adi,adv7482" for the ADV7482 >> + >> + - reg: I2C slave address >> + >> +Optional Properties: >> + >> + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or >> + "intrq3". All interrupts are optional. The "intrq3" interrupt >> + is only available on the adv7481 >> + - interrupts: Specify the interrupt lines for the ADV748x >> + >> +The device node must contain one 'port' child node per device input and output >> +port, in accordance with the video interface bindings defined in >> +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes >> +are numbered as follows. >> + >> + Name Type Port >> + --------------------------------------- >> + AIN0 sink 0 >> + AIN1 sink 1 >> + AIN2 sink 2 >> + AIN3 sink 3 >> + AIN4 sink 4 >> + AIN5 sink 5 >> + AIN6 sink 6 >> + AIN7 sink 7 >> + HDMI sink 8 >> + TTL sink 9 >> + TXA source 10 >> + TXB source 11 >> + >> +The digital output port nodes must contain at least one endpoint. >> + >> +Ports are optional if they are not connected to anything at the hardware level, >> +but the driver may not provide any support for ports which are not described. > > Not sure what is meant by 'but the driver may not provide any support for ports > which are not described'. Isn't that expected behavior if you leave out the port? Removed > >> + >> +Example: >> + >> + video_receiver@70 { >> + compatible = "adi,adv7482"; >> + reg = <0x70>; >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + interrupt-parent = <&gpio6>; >> + interrupt-names = "intrq1", "intrq2"; >> + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, >> + <31 IRQ_TYPE_LEVEL_LOW>; >> + >> + port@7 { >> + reg = <7>; >> + >> + adv7482_ain7: endpoint { >> + remote-endpoint = <&cvbs_in>; >> + }; >> + }; >> + >> + port@8 { >> + reg = <8>; >> + >> + adv7482_hdmi: endpoint { >> + remote-endpoint = <&hdmi_in>; >> + }; >> + }; >> + >> + port@10 { >> + reg = <10>; >> + >> + adv7482_txa: endpoint { >> + clock-lanes = <0>; >> + data-lanes = <1 2 3 4>; >> + remote-endpoint = <&csi40_in>; >> + }; >> + }; >> + >> + port@11 { >> + reg = <11>; >> + >> + adv7482_txb: endpoint { >> + clock-lanes = <0>; >> + data-lanes = <1>; >> + remote-endpoint = <&csi20_in>; >> + }; >> + }; >> + }; >> diff --git a/MAINTAINERS b/MAINTAINERS >> index eaaa35419fa2..7e2b65240a6f 100644 >> --- a/MAINTAINERS >> +++ b/MAINTAINERS >> @@ -776,6 +776,12 @@ L: linux-media@vger.kernel.org >> S: Maintained >> F: drivers/media/i2c/adv7511* >> +ANALOG DEVICES INC ADV748X DRIVER >> +M: Kieran Bingham <kieran.bingham@ideasonboard.com> >> +L: linux-media@vger.kernel.org >> +S: Maintained >> +F: drivers/media/i2c/adv748x/* >> + >> ANALOG DEVICES INC ADV7604 DRIVER >> M: Hans Verkuil <hans.verkuil@cisco.com> >> L: linux-media@vger.kernel.org >> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig >> index 7c23b7a1fd05..fcbec4273fef 100644 >> --- a/drivers/media/i2c/Kconfig >> +++ b/drivers/media/i2c/Kconfig >> @@ -204,6 +204,17 @@ config VIDEO_ADV7183 >> To compile this driver as a module, choose M here: the >> module will be called adv7183. >> +config VIDEO_ADV748X >> + tristate "Analog Devices ADV748x decoder" >> + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API >> + depends on OF >> + ---help--- >> + V4L2 subdevice driver for the Analog Devices >> + ADV7481 and ADV7482 HDMI/Analog video decoders. >> + >> + To compile this driver as a module, choose M here: the >> + module will be called adv748x. >> + >> config VIDEO_ADV7604 >> tristate "Analog Devices ADV7604 decoder" >> depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API >> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile >> index 62323ec66be8..e0e6045a2ec8 100644 >> --- a/drivers/media/i2c/Makefile >> +++ b/drivers/media/i2c/Makefile >> @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o >> obj-$(CONFIG_VIDEO_ADV7183) += adv7183.o >> obj-$(CONFIG_VIDEO_ADV7343) += adv7343.o >> obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o >> +obj-$(CONFIG_VIDEO_ADV748X) += adv748x/ >> obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o >> obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o >> obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o >> diff --git a/drivers/media/i2c/adv748x/Makefile >> b/drivers/media/i2c/adv748x/Makefile >> new file mode 100644 >> index 000000000000..c0711e076f1d >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/Makefile >> @@ -0,0 +1,7 @@ >> +adv748x-objs := \ >> + adv748x-afe.o \ >> + adv748x-core.o \ >> + adv748x-csi2.o \ >> + adv748x-hdmi.o >> + >> +obj-$(CONFIG_VIDEO_ADV748X) += adv748x.o >> diff --git a/drivers/media/i2c/adv748x/adv748x-afe.c >> b/drivers/media/i2c/adv748x/adv748x-afe.c >> new file mode 100644 >> index 000000000000..28e95b292d9b >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x-afe.c >> @@ -0,0 +1,571 @@ >> +/* >> + * Driver for Analog Devices ADV748X 8 channel analog front end (AFE) receiver >> + * with standard definition processor (SDP) >> + * >> + * Copyright (C) 2017 Renesas Electronics Corp. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms of the GNU General Public License as published by the >> + * Free Software Foundation; either version 2 of the License, or (at your >> + * option) any later version. >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/module.h> >> +#include <linux/mutex.h> >> +#include <linux/v4l2-dv-timings.h> >> + >> +#include <media/v4l2-ctrls.h> >> +#include <media/v4l2-device.h> >> +#include <media/v4l2-dv-timings.h> >> +#include <media/v4l2-ioctl.h> >> + >> +#include "adv748x.h" >> + >> +/* ----------------------------------------------------------------------------- >> + * SDP >> + */ >> + >> +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM 0x0 >> +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1 >> +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_J_SECAM 0x2 >> +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_M_SECAM 0x3 >> +#define ADV748X_AFE_STD_NTSC_J 0x4 >> +#define ADV748X_AFE_STD_NTSC_M 0x5 >> +#define ADV748X_AFE_STD_PAL60 0x6 >> +#define ADV748X_AFE_STD_NTSC_443 0x7 >> +#define ADV748X_AFE_STD_PAL_BG 0x8 >> +#define ADV748X_AFE_STD_PAL_N 0x9 >> +#define ADV748X_AFE_STD_PAL_M 0xa >> +#define ADV748X_AFE_STD_PAL_M_PED 0xb >> +#define ADV748X_AFE_STD_PAL_COMB_N 0xc >> +#define ADV748X_AFE_STD_PAL_COMB_N_PED 0xd >> +#define ADV748X_AFE_STD_PAL_SECAM 0xe >> +#define ADV748X_AFE_STD_PAL_SECAM_PED 0xf >> + >> +static int adv748x_afe_read_ro_map(struct adv748x_state *state, u8 reg) >> +{ >> + int ret; >> + >> + /* Select SDP Read-Only Main Map */ >> + ret = sdp_write(state, ADV748X_SDP_MAP_SEL, >> + ADV748X_SDP_MAP_SEL_RO_MAIN); >> + if (ret < 0) >> + return ret; >> + >> + return sdp_read(state, reg); >> +} >> + >> +static int adv748x_afe_status(struct adv748x_afe *afe, u32 *signal, >> + v4l2_std_id *std) >> +{ >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int info; >> + >> + /* Read status from reg 0x10 of SDP RO Map */ >> + info = adv748x_afe_read_ro_map(state, ADV748X_SDP_RO_10); >> + if (info < 0) >> + return info; >> + >> + if (signal) >> + *signal = info & ADV748X_SDP_RO_10_IN_LOCK ? >> + 0 : V4L2_IN_ST_NO_SIGNAL; >> + >> + if (!std) >> + return 0; >> + >> + /* Standard not valid if there is no signal */ >> + if (info & BIT(0)) { >> + *std = V4L2_STD_UNKNOWN; >> + return 0; >> + } >> + >> + switch (info & 0x70) { >> + case 0x00: >> + *std = V4L2_STD_NTSC; >> + break; >> + case 0x10: >> + *std = V4L2_STD_NTSC_443; >> + break; >> + case 0x20: >> + *std = V4L2_STD_PAL_M; >> + break; >> + case 0x30: >> + *std = V4L2_STD_PAL_60; >> + break; >> + case 0x40: >> + *std = V4L2_STD_PAL; >> + break; >> + case 0x50: >> + *std = V4L2_STD_SECAM; >> + break; >> + case 0x60: >> + *std = V4L2_STD_PAL_Nc | V4L2_STD_PAL_N; >> + break; >> + case 0x70: >> + *std = V4L2_STD_SECAM; >> + break; >> + default: >> + *std = V4L2_STD_UNKNOWN; >> + break; >> + } >> + >> + return 0; >> +} >> + >> +static void adv748x_afe_fill_format(struct adv748x_afe *afe, >> + struct v4l2_mbus_framefmt *fmt) >> +{ >> + v4l2_std_id std; >> + >> + memset(fmt, 0, sizeof(*fmt)); >> + >> + fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; >> + fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; >> + fmt->field = V4L2_FIELD_INTERLACED; >> + >> + fmt->width = 720; >> + >> + if (afe->curr_norm == V4L2_STD_ALL) >> + adv748x_afe_status(afe, NULL, &std); >> + else >> + std = afe->curr_norm; >> + >> + fmt->height = std & V4L2_STD_525_60 ? 480 : 576; >> +} >> + >> +static int adv748x_afe_std(v4l2_std_id std) >> +{ >> + if (std == V4L2_STD_ALL) >> + return ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM; >> + if (std == V4L2_STD_PAL_60) >> + return ADV748X_AFE_STD_PAL60; >> + if (std == V4L2_STD_NTSC_443) >> + return ADV748X_AFE_STD_NTSC_443; >> + if (std == V4L2_STD_PAL_N) >> + return ADV748X_AFE_STD_PAL_N; >> + if (std == V4L2_STD_PAL_M) >> + return ADV748X_AFE_STD_PAL_M; >> + if (std == V4L2_STD_PAL_Nc) >> + return ADV748X_AFE_STD_PAL_COMB_N; >> + if (std & V4L2_STD_PAL) >> + return ADV748X_AFE_STD_PAL_BG; >> + if (std & V4L2_STD_NTSC) >> + return ADV748X_AFE_STD_NTSC_M; > > This NTSC test should come before the PAL test. This is the order other drivers > do this as well. So a standard with a mix of NTSC and PAL bits will map to NTSC. OK Updated. > >> + if (std & V4L2_STD_SECAM) >> + return ADV748X_AFE_STD_PAL_SECAM; >> + >> + return -EINVAL; >> +} >> + >> +static int adv748x_afe_set_video_standard(struct adv748x_state *state, >> + v4l2_std_id std) >> +{ >> + int sdpstd; >> + >> + sdpstd = adv748x_afe_std(std); >> + if (sdpstd < 0) >> + return sdpstd; >> + >> + sdp_clrset(state, ADV748X_SDP_VID_SEL, ADV748X_SDP_VID_SEL_MASK, >> + (sdpstd & 0xf) << ADV748X_SDP_VID_SEL_SHIFT); >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_s_input(struct adv748x_afe *afe, unsigned int input) >> +{ >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + >> + return sdp_write(state, ADV748X_SDP_INSEL, input); >> +} >> + >> +static int adv748x_afe_g_pixelaspect(struct v4l2_subdev *sd, >> + struct v4l2_fract *aspect) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + v4l2_std_id std; >> + >> + if (afe->curr_norm == V4L2_STD_ALL) >> + adv748x_afe_status(afe, NULL, &std); >> + else >> + std = afe->curr_norm; >> + >> + if (std & V4L2_STD_525_60) { >> + aspect->numerator = 11; >> + aspect->denominator = 10; >> + } else { >> + aspect->numerator = 54; >> + aspect->denominator = 59; >> + } >> + >> + return 0; >> +} >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_video_ops >> + */ >> + >> +static int adv748x_afe_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + >> + if (afe->curr_norm == V4L2_STD_ALL) >> + adv748x_afe_status(afe, NULL, norm); >> + else >> + *norm = afe->curr_norm; >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int ret; >> + >> + mutex_lock(&state->mutex); >> + >> + ret = adv748x_afe_set_video_standard(state, std); >> + if (ret == 0) >> + afe->curr_norm = std; > > OK, so this is a bit of a problem: you are using V4L2_STD_ALL as an autodetect > mechanism, but that is not allowed by the V4L2 specification. Yes, some old > drivers do this and we don't dare to change that, but new drivers should not > attempt this. The standard set and reported by s_std and g_std must always > be precise, i.e. no mix of NTSC and PAL. > > Only QUERYSTD is allowed to detect the format. So how about using V4L2_STD_UNKNOWN as the hint to autodetect and initialising to NTSC as you suggest in probe. g_std will then always return either the initial value, a detected value, or unknown if no lock is available. Although then, I'd almost prefer to initialise to V4L2_STD_UNKNOWN ... > > So > >> + >> + mutex_unlock(&state->mutex); >> + >> + return ret; >> +} >> + >> +static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int ret; >> + >> + mutex_lock(&state->mutex); >> + >> + if (afe->streaming) { >> + ret = -EBUSY; >> + goto unlock; >> + } >> + >> + /* Set auto detect mode */ >> + ret = adv748x_afe_set_video_standard(state, V4L2_STD_ALL); I.e. - I'll set V4L2_STD_UNKNOWN here ... >> + if (ret) >> + goto unlock; >> + >> + msleep(100); >> + >> + /* Read detected standard */ >> + ret = adv748x_afe_status(afe, NULL, std); >> +unlock: >> + mutex_unlock(&state->mutex); >> + >> + return ret; >> +} >> + >> +static int adv748x_afe_g_tvnorms(struct v4l2_subdev *sd, v4l2_std_id *norm) >> +{ >> + *norm = V4L2_STD_ALL; >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_g_input_status(struct v4l2_subdev *sd, u32 *status) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int ret; >> + >> + mutex_lock(&state->mutex); >> + >> + ret = adv748x_afe_status(afe, status, NULL); >> + >> + mutex_unlock(&state->mutex); >> + return ret; >> +} >> + >> +static int adv748x_afe_s_stream(struct v4l2_subdev *sd, int enable) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int ret, signal = V4L2_IN_ST_NO_SIGNAL; >> + >> + mutex_lock(&state->mutex); >> + >> + if (enable) { >> + ret = adv748x_afe_s_input(afe, afe->input); >> + if (ret) >> + goto unlock; >> + } >> + >> + ret = adv748x_txb_power(state, enable); >> + if (ret) >> + goto unlock; >> + >> + afe->streaming = enable; >> + >> + adv748x_afe_status(afe, &signal, NULL); >> + if (signal != V4L2_IN_ST_NO_SIGNAL) >> + adv_dbg(state, "Detected SDP signal\n"); >> + else >> + adv_dbg(state, "Couldn't detect SDP video signal\n"); >> + >> +unlock: >> + mutex_unlock(&state->mutex); >> + >> + return ret; >> +} >> + >> +static const struct v4l2_subdev_video_ops adv748x_afe_video_ops = { >> + .g_std = adv748x_afe_g_std, >> + .s_std = adv748x_afe_s_std, >> + .querystd = adv748x_afe_querystd, >> + .g_tvnorms = adv748x_afe_g_tvnorms, >> + .g_input_status = adv748x_afe_g_input_status, >> + .s_stream = adv748x_afe_s_stream, >> + .g_pixelaspect = adv748x_afe_g_pixelaspect, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_pad_ops >> + */ >> + >> +static int adv748x_afe_set_pixelrate(struct adv748x_afe *afe) >> +{ >> + struct v4l2_subdev *tx; >> + unsigned int width, height, fps; >> + >> + tx = adv748x_get_remote_sd(&afe->pads[ADV748X_AFE_SOURCE]); >> + if (!tx) >> + return -ENOLINK; >> + >> + width = 720; >> + height = afe->curr_norm & V4L2_STD_525_60 ? 480 : 576; >> + fps = afe->curr_norm & V4L2_STD_525_60 ? 30 : 25; >> + >> + return adv748x_csi2_set_pixelrate(tx, width * height * fps); >> +} >> + >> +static int adv748x_afe_enum_mbus_code(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_mbus_code_enum *code) >> +{ >> + if (code->index != 0) >> + return -EINVAL; >> + >> + code->code = MEDIA_BUS_FMT_UYVY8_2X8; >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_get_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + /* The format of the analog sink pads is nonsensical */ > > You mean: /* It makes no sense to get the format of analog sink pads */ > > I misread your comment as meaning that the *format* made no sense. Re-written as you suggested. > >> + if (sdformat->pad != ADV748X_AFE_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + sdformat->format = *mbusformat; >> + } else { >> + adv748x_afe_fill_format(afe, &sdformat->format); >> + adv748x_afe_set_pixelrate(afe); >> + } >> + >> + return 0; >> +} >> + >> +static int adv748x_afe_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + /* The format of the analog sink pads is nonsensical */ > > Ditto. Ditto. > >> + if (sdformat->pad != ADV748X_AFE_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) >> + return adv748x_afe_get_format(sd, cfg, sdformat); >> + >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + *mbusformat = sdformat->format; >> + >> + return 0; >> +} >> + >> +static const struct v4l2_subdev_pad_ops adv748x_afe_pad_ops = { >> + .enum_mbus_code = adv748x_afe_enum_mbus_code, >> + .set_fmt = adv748x_afe_set_format, >> + .get_fmt = adv748x_afe_get_format, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_ops >> + */ >> + >> +static const struct v4l2_subdev_ops adv748x_afe_ops = { >> + .video = &adv748x_afe_video_ops, >> + .pad = &adv748x_afe_pad_ops, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * Controls >> + */ >> + >> +static const char * const afe_ctrl_frp_menu[] = { >> + "Disabled", >> + "Default Value", > > What does this mean? It is not very descriptive. It means output a value which is configured by the default value register. So it's a programmable value, but I have not provided a way to set the colour. I've just taken the string literals from the datasheet... > >> + "Color Bars", >> + "Grey Ramp", >> + "Cb Ramp", >> + "Cr Ramp", >> + "Boundary" >> +}; >> + >> +static int adv748x_afe_s_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct adv748x_afe *afe = adv748x_ctrl_to_afe(ctrl); >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + bool enable; >> + int ret; >> + >> + ret = sdp_write(state, 0x0e, 0x00); >> + if (ret < 0) >> + return ret; >> + >> + switch (ctrl->id) { >> + case V4L2_CID_BRIGHTNESS: >> + ret = sdp_write(state, ADV748X_SDP_BRI, ctrl->val); >> + break; >> + case V4L2_CID_HUE: >> + /* Hue is inverted according to HSL chart */ >> + ret = sdp_write(state, ADV748X_SDP_HUE, -ctrl->val); >> + break; >> + case V4L2_CID_CONTRAST: >> + ret = sdp_write(state, ADV748X_SDP_CON, ctrl->val); >> + break; >> + case V4L2_CID_SATURATION: >> + ret = sdp_write(state, ADV748X_SDP_SD_SAT_U, ctrl->val); >> + if (ret) >> + break; >> + ret = sdp_write(state, ADV748X_SDP_SD_SAT_V, ctrl->val); >> + break; >> + case V4L2_CID_TEST_PATTERN: >> + enable = !!ctrl->val; >> + >> + /* Enable/Disable Color bar test patterns */ >> + ret = sdp_clrset(state, ADV748X_SDP_DEF, ADV748X_SDP_DEF_VAL_EN, >> + enable); >> + if (ret) >> + break; >> + ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, >> + enable ? ctrl->val - 1 : 0); >> + break; >> + default: >> + return -EINVAL; >> + } >> + >> + return ret; >> +} >> + >> +static const struct v4l2_ctrl_ops adv748x_afe_ctrl_ops = { >> + .s_ctrl = adv748x_afe_s_ctrl, >> +}; >> + >> +static int adv748x_afe_init_controls(struct adv748x_afe *afe) >> +{ >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + >> + v4l2_ctrl_handler_init(&afe->ctrl_hdl, 5); >> + >> + /* Use our mutex for the controls */ >> + afe->ctrl_hdl.lock = &state->mutex; >> + >> + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, >> + V4L2_CID_BRIGHTNESS, ADV748X_SDP_BRI_MIN, >> + ADV748X_SDP_BRI_MAX, 1, ADV748X_SDP_BRI_DEF); >> + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, >> + V4L2_CID_CONTRAST, ADV748X_SDP_CON_MIN, >> + ADV748X_SDP_CON_MAX, 1, ADV748X_SDP_CON_DEF); >> + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, >> + V4L2_CID_SATURATION, ADV748X_SDP_SAT_MIN, >> + ADV748X_SDP_SAT_MAX, 1, ADV748X_SDP_SAT_DEF); >> + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, >> + V4L2_CID_HUE, ADV748X_SDP_HUE_MIN, >> + ADV748X_SDP_HUE_MAX, 1, ADV748X_SDP_HUE_DEF); >> + >> + v4l2_ctrl_new_std_menu_items(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, >> + V4L2_CID_TEST_PATTERN, >> + ARRAY_SIZE(afe_ctrl_frp_menu) - 1, >> + 0, 0, afe_ctrl_frp_menu); >> + >> + afe->sd.ctrl_handler = &afe->ctrl_hdl; >> + if (afe->ctrl_hdl.error) { >> + v4l2_ctrl_handler_free(&afe->ctrl_hdl); >> + return afe->ctrl_hdl.error; >> + } >> + >> + return v4l2_ctrl_handler_setup(&afe->ctrl_hdl); >> +} >> + >> +int adv748x_afe_init(struct adv748x_afe *afe) >> +{ >> + struct adv748x_state *state = adv748x_afe_to_state(afe); >> + int ret; >> + unsigned int i; >> + >> + afe->input = 0; >> + afe->streaming = false; >> + afe->curr_norm = V4L2_STD_ALL; > > No. This must be a valid standard. Typically V4L2_STD_NTSC_M. Wouldn't V4L2_STD_UNKNOWN be more reasonable at this stage? >> + >> + adv748x_subdev_init(&afe->sd, state, &adv748x_afe_ops, >> + MEDIA_ENT_F_ATV_DECODER, "afe"); >> + >> + /* Identify the first connector found as a default input if set */ >> + for (i = ADV748X_PORT_AIN0; i <= ADV748X_PORT_AIN7; i++) { >> + /* Inputs and ports are 1-indexed to match the data sheet */ >> + if (state->endpoints[i]) { >> + afe->input = i; >> + break; >> + } >> + } >> + >> + adv748x_afe_s_input(afe, afe->input); >> + >> + adv_dbg(state, "AFE Default input set to %d\n", afe->input); >> + >> + /* Entity pads and sinks are 0-indexed to match the pads */ >> + for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++) >> + afe->pads[i].flags = MEDIA_PAD_FL_SINK; >> + >> + afe->pads[ADV748X_AFE_SOURCE].flags = MEDIA_PAD_FL_SOURCE; >> + >> + ret = media_entity_pads_init(&afe->sd.entity, ADV748X_AFE_NR_PADS, >> + afe->pads); >> + if (ret) >> + return ret; >> + >> + ret = adv748x_afe_init_controls(afe); >> + if (ret) >> + goto error; >> + >> + return 0; >> + >> +error: >> + media_entity_cleanup(&afe->sd.entity); >> + >> + return ret; >> +} >> + >> +void adv748x_afe_cleanup(struct adv748x_afe *afe) >> +{ >> + v4l2_device_unregister_subdev(&afe->sd); >> + media_entity_cleanup(&afe->sd.entity); >> + v4l2_ctrl_handler_free(&afe->ctrl_hdl); >> +} >> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c >> b/drivers/media/i2c/adv748x/adv748x-core.c >> new file mode 100644 >> index 000000000000..6e395a4524ec >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x-core.c >> @@ -0,0 +1,907 @@ >> +/* >> + * Driver for Analog Devices ADV748X HDMI receiver with AFE >> + * >> + * Copyright (C) 2017 Renesas Electronics Corp. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms of the GNU General Public License as published by the >> + * Free Software Foundation; either version 2 of the License, or (at your >> + * option) any later version. >> + * >> + * Authors: >> + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> >> + * Niklas Söderlund <niklas.soderlund@ragnatech.se> >> + * Kieran Bingham <kieran.bingham@ideasonboard.com> >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/errno.h> >> +#include <linux/i2c.h> >> +#include <linux/module.h> >> +#include <linux/mutex.h> >> +#include <linux/of_graph.h> >> +#include <linux/regmap.h> >> +#include <linux/v4l2-dv-timings.h> >> + >> +#include <media/v4l2-ctrls.h> >> +#include <media/v4l2-device.h> >> +#include <media/v4l2-dv-timings.h> >> +#include <media/v4l2-ioctl.h> >> + >> +#include "adv748x.h" >> + >> +/* ----------------------------------------------------------------------------- >> + * Register manipulation >> + */ >> + >> +static const struct regmap_config adv748x_regmap_cnf[] = { >> + { >> + .name = "io", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "dpll", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "cp", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "hdmi", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "edid", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "repeater", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "infoframe", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "cec", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "sdp", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + >> + { >> + .name = "txb", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> + { >> + .name = "txa", >> + .reg_bits = 8, >> + .val_bits = 8, >> + >> + .max_register = 0xff, >> + .cache_type = REGCACHE_NONE, >> + }, >> +}; >> + >> +static int adv748x_configure_regmap(struct adv748x_state *state, int region) >> +{ >> + int err; >> + >> + if (!state->i2c_clients[region]) >> + return -ENODEV; >> + >> + state->regmap[region] = >> + devm_regmap_init_i2c(state->i2c_clients[region], >> + &adv748x_regmap_cnf[region]); >> + >> + if (IS_ERR(state->regmap[region])) { >> + err = PTR_ERR(state->regmap[region]); >> + adv_err(state, >> + "Error initializing regmap %d with error %d\n", >> + region, err); >> + return -EINVAL; >> + } >> + >> + return 0; >> +} >> + >> +/* Default addresses for the I2C pages */ >> +static int adv748x_i2c_addresses[ADV748X_PAGE_MAX] = { >> + ADV748X_I2C_IO, >> + ADV748X_I2C_DPLL, >> + ADV748X_I2C_CP, >> + ADV748X_I2C_HDMI, >> + ADV748X_I2C_EDID, >> + ADV748X_I2C_REPEATER, >> + ADV748X_I2C_INFOFRAME, >> + ADV748X_I2C_CEC, >> + ADV748X_I2C_SDP, >> + ADV748X_I2C_TXB, >> + ADV748X_I2C_TXA, >> +}; >> + >> +static int adv748x_read_check(struct adv748x_state *state, >> + int client_page, u8 reg) >> +{ >> + struct i2c_client *client = state->i2c_clients[client_page]; >> + int err; >> + unsigned int val; >> + >> + err = regmap_read(state->regmap[client_page], reg, &val); >> + >> + if (err) { >> + adv_err(state, "error reading %02x, %02x\n", >> + client->addr, reg); >> + return err; >> + } >> + >> + return val; >> +} >> + >> +int adv748x_read(struct adv748x_state *state, u8 page, u8 reg) >> +{ >> + return adv748x_read_check(state, page, reg); >> +} >> + >> +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value) >> +{ >> + return regmap_write(state->regmap[page], reg, value); >> +} >> + >> +/* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX >> + * size to one or more registers. >> + * >> + * A value of zero will be returned on success, a negative errno will >> + * be returned in error cases. >> + */ >> +int adv748x_write_block(struct adv748x_state *state, int client_page, >> + unsigned int init_reg, const void *val, >> + size_t val_len) >> +{ >> + struct regmap *regmap = state->regmap[client_page]; >> + >> + if (val_len > I2C_SMBUS_BLOCK_MAX) >> + val_len = I2C_SMBUS_BLOCK_MAX; >> + >> + return regmap_raw_write(regmap, init_reg, val, val_len); >> +} >> + >> + >> +static struct i2c_client *adv748x_dummy_client(struct adv748x_state *state, >> + u8 addr, u8 io_reg) >> +{ >> + struct i2c_client *client = state->client; >> + >> + if (addr) >> + io_write(state, io_reg, addr << 1); >> + >> + return i2c_new_dummy(client->adapter, io_read(state, io_reg) >> 1); >> +} >> + >> +static void adv748x_unregister_clients(struct adv748x_state *state) >> +{ >> + unsigned int i; >> + >> + for (i = 1; i < ARRAY_SIZE(state->i2c_clients); ++i) { >> + if (state->i2c_clients[i]) >> + i2c_unregister_device(state->i2c_clients[i]); >> + } >> +} >> + >> +static int adv748x_initialise_clients(struct adv748x_state *state) >> +{ >> + int i; >> + int ret; >> + >> + for (i = ADV748X_PAGE_DPLL; i < ADV748X_PAGE_MAX; ++i) { >> + state->i2c_clients[i] = >> + adv748x_dummy_client(state, adv748x_i2c_addresses[i], >> + ADV748X_IO_SLAVE_ADDR_BASE + i); >> + if (state->i2c_clients[i] == NULL) { >> + adv_err(state, "failed to create i2c client %u\n", i); >> + return -ENOMEM; >> + } >> + >> + ret = adv748x_configure_regmap(state, i); >> + if (ret) >> + return ret; >> + } >> + >> + return 0; >> +} >> + >> +/** >> + * struct adv748x_reg_value - Register write instruction >> + * @page: Regmap page identifier >> + * @reg: I2C register >> + * @value: value to write to @page at @reg >> + */ >> +struct adv748x_reg_value { >> + u8 page; >> + u8 reg; >> + u8 value; >> +}; >> + >> +static int adv748x_write_regs(struct adv748x_state *state, >> + const struct adv748x_reg_value *regs) >> +{ >> + int ret; >> + >> + while (regs->page != ADV748X_PAGE_EOR) { >> + if (regs->page == ADV748X_PAGE_WAIT) { >> + msleep(regs->value); >> + } else { >> + ret = adv748x_write(state, regs->page, regs->reg, >> + regs->value); >> + if (ret < 0) { >> + adv_err(state, >> + "Error regs page: 0x%02x reg: 0x%02x\n", >> + regs->page, regs->reg); >> + return ret; >> + } >> + } >> + regs++; >> + } >> + >> + return 0; >> +} >> + >> + >> +/* ----------------------------------------------------------------------------- >> + * TXA and TXB >> + */ >> + >> +static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = { >> + >> + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ >> + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ >> + >> + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ >> + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = { >> + >> + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x1e, 0x00}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ >> + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + {ADV748X_PAGE_TXA, 0xc1, 0x3b}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = { >> + >> + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ >> + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ >> + >> + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ >> + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = { >> + >> + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x1e, 0x00}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 4-lane MIPI */ >> + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + {ADV748X_PAGE_TXB, 0xc1, 0x3b}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +int adv748x_txa_power(struct adv748x_state *state, bool on) >> +{ >> + int val; >> + >> + val = txa_read(state, ADV748X_CSI_FS_AS_LS); >> + if (val < 0) >> + return val; >> + >> + /* >> + * This test against BIT(6) is not documented by the datasheet, but was >> + * specified in the downstream driver. >> + * Track with a WARN_ONCE to determine if it is ever set by HW. >> + */ >> + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), >> + "Enabling with unknown bit set"); >> + >> + if (on) >> + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); >> + else > > 'else' isn't needed. That's a shame - I think the code is more elegant (/symmetrical) this way - but no worries. Adapted. (same for the others) > >> + return adv748x_write_regs(state, adv748x_power_down_txa_4lane); >> +} >> + >> +int adv748x_txb_power(struct adv748x_state *state, bool on) >> +{ >> + int val; >> + >> + val = txb_read(state, ADV748X_CSI_FS_AS_LS); >> + if (val < 0) >> + return val; >> + >> + /* >> + * This test against BIT(6) is not documented by the datasheet, but was >> + * specified in the downstream driver. >> + * Track with a WARN_ONCE to determine if it is ever set by HW. >> + */ >> + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), >> + "Enabling with unknown bit set"); >> + >> + if (on) >> + return adv748x_write_regs(state, adv748x_power_up_txb_1lane); >> + else > > Ditto. > >> + return adv748x_write_regs(state, adv748x_power_down_txb_1lane); >> +} >> + >> +/* ----------------------------------------------------------------------------- >> + * Media Operations >> + */ >> + >> +static const struct media_entity_operations adv748x_media_ops = { >> + .link_validate = v4l2_subdev_link_validate, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * HW setup >> + */ >> + >> +static const struct adv748x_reg_value adv748x_sw_reset[] = { >> + >> + {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */ >> + {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */ >> + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +static const struct adv748x_reg_value adv748x_set_slave_address[] = { >> + {ADV748X_PAGE_IO, 0xf3, ADV748X_I2C_DPLL << 1}, >> + {ADV748X_PAGE_IO, 0xf4, ADV748X_I2C_CP << 1}, >> + {ADV748X_PAGE_IO, 0xf5, ADV748X_I2C_HDMI << 1}, >> + {ADV748X_PAGE_IO, 0xf6, ADV748X_I2C_EDID << 1}, >> + {ADV748X_PAGE_IO, 0xf7, ADV748X_I2C_REPEATER << 1}, >> + {ADV748X_PAGE_IO, 0xf8, ADV748X_I2C_INFOFRAME << 1}, >> + {ADV748X_PAGE_IO, 0xfa, ADV748X_I2C_CEC << 1}, >> + {ADV748X_PAGE_IO, 0xfb, ADV748X_I2C_SDP << 1}, >> + {ADV748X_PAGE_IO, 0xfc, ADV748X_I2C_TXB << 1}, >> + {ADV748X_PAGE_IO, 0xfd, ADV748X_I2C_TXA << 1}, >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +/* Supported Formats For Script Below */ >> +/* - 01-29 HDMI to MIPI TxA CSI 4-Lane - RGB888: */ >> +static const struct adv748x_reg_value adv748x_init_txa_4lane[] = { >> + /* Disable chip powerdown & Enable HDMI Rx block */ >> + {ADV748X_PAGE_IO, 0x00, 0x40}, >> + >> + {ADV748X_PAGE_REPEATER, 0x40, 0x83}, /* Enable HDCP 1.1 */ >> + >> + {ADV748X_PAGE_HDMI, 0x00, 0x08},/* Foreground Channel = A */ >> + {ADV748X_PAGE_HDMI, 0x98, 0xff},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x99, 0xa3},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x9a, 0x00},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x9b, 0x0a},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x9d, 0x40},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0xcb, 0x09},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x3d, 0x10},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x3e, 0x7b},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x3f, 0x5e},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x4e, 0xfe},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x4f, 0x18},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x57, 0xa3},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x58, 0x04},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0x85, 0x10},/* ADI Required Write */ >> + >> + {ADV748X_PAGE_HDMI, 0x83, 0x00},/* Enable All Terminations */ >> + {ADV748X_PAGE_HDMI, 0xa3, 0x01},/* ADI Required Write */ >> + {ADV748X_PAGE_HDMI, 0xbe, 0x00},/* ADI Required Write */ >> + >> + {ADV748X_PAGE_HDMI, 0x6c, 0x01},/* HPA Manual Enable */ >> + {ADV748X_PAGE_HDMI, 0xf8, 0x01},/* HPA Asserted */ >> + {ADV748X_PAGE_HDMI, 0x0f, 0x00},/* Audio Mute Speed Set to Fastest */ >> + /* (Smallest Step Size) */ >> + >> + {ADV748X_PAGE_IO, 0x04, 0x02}, /* RGB Out of CP */ >> + {ADV748X_PAGE_IO, 0x12, 0xf0}, /* CSC Depends on ip Packets, SDR 444 */ >> + {ADV748X_PAGE_IO, 0x17, 0x80}, /* Luma & Chroma can reach 254d */ >> + {ADV748X_PAGE_IO, 0x03, 0x86}, /* CP-Insert_AV_Code */ >> + >> + {ADV748X_PAGE_CP, 0x7c, 0x00}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_IO, 0x0c, 0xe0}, /* Enable LLC_DLL & Double LLC Timing */ >> + {ADV748X_PAGE_IO, 0x0e, 0xdd}, /* LLC/PIX/SPI PINS TRISTATED AUD */ >> + /* Outputs Enabled */ >> + {ADV748X_PAGE_IO, 0x10, 0xa0}, /* Enable 4-lane CSI Tx & Pixel Port */ >> + >> + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ >> + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ >> + {ADV748X_PAGE_TXA, 0xdb, 0x10}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0xd6, 0x07}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0xc4, 0x0a}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x71, 0x33}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x72, 0x11}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ >> + >> + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ >> + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +/* 02-01 Analog CVBS to MIPI TX-B CSI 1-Lane - */ >> +/* Autodetect CVBS Single Ended In Ain 1 - MIPI Out */ >> +static const struct adv748x_reg_value adv748x_init_txb_1lane[] = { >> + >> + {ADV748X_PAGE_IO, 0x00, 0x30}, /* Disable chip powerdown Rx */ >> + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ >> + >> + {ADV748X_PAGE_IO, 0x0e, 0xff}, /* LLC/PIX/AUD/SPI PINS TRISTATED */ >> + >> + {ADV748X_PAGE_SDP, 0x0f, 0x00}, /* Exit Power Down Mode */ >> + {ADV748X_PAGE_SDP, 0x52, 0xcd}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_SDP, 0x0e, 0x80}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0x9c, 0x00}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0x9c, 0xff}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0x0e, 0x00}, /* ADI Required Write */ >> + >> + /* ADI recommended writes for improved video quality */ >> + {ADV748X_PAGE_SDP, 0x80, 0x51}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0x81, 0x51}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0x82, 0x68}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_SDP, 0x03, 0x42}, /* Tri-S Output , PwrDwn 656 pads */ >> + {ADV748X_PAGE_SDP, 0x04, 0xb5}, /* ITU-R BT.656-4 compatible */ >> + {ADV748X_PAGE_SDP, 0x13, 0x00}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_SDP, 0x17, 0x41}, /* Select SH1 */ >> + {ADV748X_PAGE_SDP, 0x31, 0x12}, /* ADI Required Write */ >> + {ADV748X_PAGE_SDP, 0xe6, 0x4f}, /* V bit end pos manually in NTSC */ >> + >> + /* Enable 1-Lane MIPI Tx, */ >> + /* enable pixel output and route SD through Pixel port */ >> + {ADV748X_PAGE_IO, 0x10, 0x70}, >> + >> + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ >> + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ >> + {ADV748X_PAGE_TXB, 0xd2, 0x40}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0xc4, 0x0a}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x71, 0x33}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x72, 0x11}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ >> + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ >> + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ >> + >> + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ >> + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ >> + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ >> + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ >> + >> + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ >> +}; >> + >> +static int adv748x_reset(struct adv748x_state *state) >> +{ >> + int ret; >> + >> + ret = adv748x_write_regs(state, adv748x_sw_reset); >> + if (ret < 0) >> + return ret; >> + >> + ret = adv748x_write_regs(state, adv748x_set_slave_address); >> + if (ret < 0) >> + return ret; >> + >> + /* Init and power down TXA */ >> + ret = adv748x_write_regs(state, adv748x_init_txa_4lane); >> + if (ret) >> + return ret; >> + >> + adv748x_txa_power(state, 0); >> + >> + /* Init and power down TXB */ >> + ret = adv748x_write_regs(state, adv748x_init_txb_1lane); >> + if (ret) >> + return ret; >> + >> + adv748x_txb_power(state, 0); >> + >> + /* Disable chip powerdown & Enable HDMI Rx block */ >> + io_write(state, ADV748X_IO_PD, ADV748X_IO_PD_RX_EN); >> + >> + /* Enable 4-lane CSI Tx & Pixel Port */ >> + io_write(state, ADV748X_IO_10, ADV748X_IO_10_CSI4_EN | >> + ADV748X_IO_10_CSI1_EN | >> + ADV748X_IO_10_PIX_OUT_EN); >> + >> + /* Use vid_std and v_freq as freerun resolution for CP */ >> + cp_clrset(state, ADV748X_CP_CLMP_POS, ADV748X_CP_CLMP_POS_DIS_AUTO, >> + ADV748X_CP_CLMP_POS_DIS_AUTO); >> + >> + return 0; >> +} >> + >> +static int adv748x_identify_chip(struct adv748x_state *state) >> +{ >> + int msb, lsb; >> + >> + lsb = io_read(state, ADV748X_IO_CHIP_REV_ID_1); >> + msb = io_read(state, ADV748X_IO_CHIP_REV_ID_2); >> + >> + if (lsb < 0 || msb < 0) { >> + adv_err(state, "Failed to read chip revision\n"); >> + return -EIO; >> + } >> + >> + adv_info(state, "chip found @ 0x%02x revision %02x%02x\n", >> + state->client->addr << 1, lsb, msb); >> + >> + return 0; >> +} >> + >> +/* ----------------------------------------------------------------------------- >> + * i2c driver >> + */ >> + >> +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, >> + const struct v4l2_subdev_ops *ops, u32 function, >> + const char *ident) >> +{ >> + v4l2_subdev_init(sd, ops); >> + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; >> + >> + /* the owner is the same as the i2c_client's driver owner */ >> + sd->owner = state->dev->driver->owner; >> + sd->dev = state->dev; >> + >> + v4l2_set_subdevdata(sd, state); >> + >> + /* initialize name */ >> + snprintf(sd->name, sizeof(sd->name), "%s %d-%04x %s", >> + state->dev->driver->name, >> + i2c_adapter_id(state->client->adapter), >> + state->client->addr, ident); >> + >> + sd->entity.function = function; >> + sd->entity.ops = &adv748x_media_ops; >> +} >> + >> +static int adv748x_parse_dt(struct adv748x_state *state) >> +{ >> + struct device_node *ep_np = NULL; >> + struct of_endpoint ep; >> + bool found = false; >> + >> + for_each_endpoint_of_node(state->dev->of_node, ep_np) { >> + of_graph_parse_endpoint(ep_np, &ep); >> + adv_info(state, "Endpoint %s on port %d", >> + of_node_full_name(ep.local_node), >> + ep.port); >> + >> + if (ep.port >= ADV748X_PORT_MAX) { >> + adv_err(state, "Invalid endpoint %s on port %d", >> + of_node_full_name(ep.local_node), >> + ep.port); >> + >> + continue; >> + } >> + >> + if (state->endpoints[ep.port]) { >> + adv_err(state, >> + "Multiple port endpoints are not supported"); >> + continue; >> + } >> + >> + of_node_get(ep_np); >> + state->endpoints[ep.port] = ep_np; >> + >> + found = true; >> + } >> + >> + return found ? 0 : -ENODEV; >> +} >> + >> +static void adv748x_dt_cleanup(struct adv748x_state *state) >> +{ >> + unsigned int i; >> + >> + for (i = 0; i < ADV748X_PORT_MAX; i++) >> + of_node_put(state->endpoints[i]); >> +} >> + >> +static int adv748x_setup_links(struct adv748x_state *state) >> +{ >> + int ret; >> + int enabled = MEDIA_LNK_FL_ENABLED; >> + >> +/* >> + * HACK/Workaround: >> + * >> + * Currently non-immutable link resets go through the RVin >> + * driver, and cause the links to fail, due to not being part of RVIN. >> + * As a temporary workaround until the RVIN driver knows better than to parse >> + * links that do not belong to it, use static immutable links for our internal >> + * media paths. >> + */ >> +#define ADV748x_DEV_STATIC_LINKS >> +#ifdef ADV748x_DEV_STATIC_LINKS >> + enabled |= MEDIA_LNK_FL_IMMUTABLE; >> +#endif > > Has an RVIN patch fixing this been posted yet? If not, is anyone looking at that? > Perhaps this should use #ifdef CONFIG_VIDEO_RCAR_VIN instead of inventing a define? Sorry - this is actaully dead code from the V4 - adv748x_setup_links isn't even called in this version. Niklas noticed it - with removal in V5. I've converted to just supporting static links. Which is better as there is no code to support changing the routing yet anyway. > >> + >> + /* TXA - Default link is with HDMI */ >> + ret = media_create_pad_link(&state->hdmi.sd.entity, 1, >> + &state->txa.sd.entity, 0, enabled); >> + if (ret) { >> + adv_err(state, "Failed to create HDMI-TXA pad link"); >> + return ret; >> + } >> + >> +#ifndef ADV748x_DEV_STATIC_LINKS >> + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, >> + &state->txa.sd.entity, 0, 0); >> + if (ret) { >> + adv_err(state, "Failed to create AFE-TXA pad link"); >> + return ret; >> + } >> +#endif >> + >> + /* TXB - Can only output from the AFE */ >> + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, >> + &state->txb.sd.entity, 0, enabled); >> + if (ret) { >> + adv_err(state, "Failed to create AFE-TXB pad link"); >> + return ret; >> + } >> + >> + return 0; >> +} >> + >> +int adv748x_register_subdevs(struct adv748x_state *state, >> + struct v4l2_device *v4l2_dev) >> +{ >> + int ret; >> + >> + ret = v4l2_device_register_subdev(v4l2_dev, &state->hdmi.sd); >> + if (ret < 0) >> + return ret; >> + >> + ret = v4l2_device_register_subdev(v4l2_dev, &state->afe.sd); >> + if (ret < 0) >> + goto err_unregister_hdmi; >> + >> + ret = adv748x_setup_links(state); >> + if (ret < 0) >> + goto err_unregister_afe; >> + >> + return 0; >> + >> +err_unregister_afe: >> + v4l2_device_unregister_subdev(&state->afe.sd); >> +err_unregister_hdmi: >> + v4l2_device_unregister_subdev(&state->hdmi.sd); >> + >> + return ret; >> +} >> + >> +static int adv748x_probe(struct i2c_client *client, >> + const struct i2c_device_id *id) >> +{ >> + struct adv748x_state *state; >> + int ret; >> + >> + /* Check if the adapter supports the needed features */ >> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) >> + return -EIO; >> + >> + state = kzalloc(sizeof(struct adv748x_state), GFP_KERNEL); >> + if (!state) >> + return -ENOMEM; >> + >> + mutex_init(&state->mutex); >> + >> + state->dev = &client->dev; >> + state->client = client; >> + state->i2c_clients[ADV748X_PAGE_IO] = client; >> + i2c_set_clientdata(client, state); >> + >> + /* Discover and process ports declared by the Device tree endpoints */ >> + ret = adv748x_parse_dt(state); >> + if (ret) { >> + adv_err(state, "Failed to parse device tree"); >> + goto err_free_mutex; >> + } >> + >> + /* Configure IO Regmap region */ >> + ret = adv748x_configure_regmap(state, ADV748X_PAGE_IO); >> + if (ret) { >> + adv_err(state, "Error configuring IO regmap region"); >> + goto err_cleanup_dt; >> + } >> + >> + ret = adv748x_identify_chip(state); >> + if (ret) { >> + adv_err(state, "Failed to identify chip"); >> + goto err_cleanup_clients; >> + } >> + >> + /* Configure remaining pages as I2C clients with regmap access */ >> + ret = adv748x_initialise_clients(state); >> + if (ret) { >> + adv_err(state, "Failed to setup client regmap pages"); >> + goto err_cleanup_clients; >> + } >> + >> + /* SW reset ADV748X to its default values */ >> + ret = adv748x_reset(state); >> + if (ret) { >> + adv_err(state, "Failed to reset hardware"); >> + goto err_cleanup_clients; >> + } >> + >> + /* Initialise HDMI */ >> + ret = adv748x_hdmi_init(&state->hdmi); >> + if (ret) { >> + adv_err(state, "Failed to probe HDMI"); >> + goto err_cleanup_clients; >> + } >> + >> + /* Initialise AFE */ >> + ret = adv748x_afe_init(&state->afe); >> + if (ret) { >> + adv_err(state, "Failed to probe AFE"); >> + goto err_cleanup_hdmi; >> + } >> + >> + /* Initialise TXA */ >> + ret = adv748x_csi2_init(state, &state->txa); >> + if (ret) { >> + adv_err(state, "Failed to probe TXA"); >> + goto err_cleanup_afe; >> + } >> + >> + /* Initialise TXB */ >> + ret = adv748x_csi2_init(state, &state->txb); >> + if (ret) { >> + adv_err(state, "Failed to probe TXB"); >> + goto err_cleanup_txa; >> + } >> + >> + return 0; >> + >> +err_cleanup_txa: >> + adv748x_csi2_cleanup(&state->txa); >> +err_cleanup_afe: >> + adv748x_afe_cleanup(&state->afe); >> +err_cleanup_hdmi: >> + adv748x_hdmi_cleanup(&state->hdmi); >> +err_cleanup_clients: >> + adv748x_unregister_clients(state); >> +err_cleanup_dt: >> + adv748x_dt_cleanup(state); >> +err_free_mutex: >> + mutex_destroy(&state->mutex); >> + kfree(state); >> + >> + return ret; >> +} >> + >> +static int adv748x_remove(struct i2c_client *client) >> +{ >> + struct adv748x_state *state = i2c_get_clientdata(client); >> + >> + adv748x_afe_cleanup(&state->afe); >> + adv748x_hdmi_cleanup(&state->hdmi); >> + >> + adv748x_csi2_cleanup(&state->txa); >> + adv748x_csi2_cleanup(&state->txb); >> + >> + adv748x_unregister_clients(state); >> + adv748x_dt_cleanup(state); >> + mutex_destroy(&state->mutex); >> + >> + kfree(state); >> + >> + return 0; >> +} >> + >> +static const struct i2c_device_id adv748x_id[] = { >> + { "adv7481", 0 }, >> + { "adv7482", 0 }, >> + { }, >> +}; >> + >> +static const struct of_device_id adv748x_of_table[] = { >> + { .compatible = "adi,adv7481", }, >> + { .compatible = "adi,adv7482", }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, adv748x_of_table); >> + >> +static struct i2c_driver adv748x_driver = { >> + .driver = { >> + .name = "adv748x", >> + .of_match_table = adv748x_of_table, >> + }, >> + .probe = adv748x_probe, >> + .remove = adv748x_remove, >> + .id_table = adv748x_id, >> +}; >> + >> +module_i2c_driver(adv748x_driver); >> + >> +MODULE_AUTHOR("Kieran Bingham <kieran.bingham@ideasonboard.com>"); >> +MODULE_DESCRIPTION("ADV748X video decoder"); >> +MODULE_LICENSE("GPL v2"); >> diff --git a/drivers/media/i2c/adv748x/adv748x-csi2.c >> b/drivers/media/i2c/adv748x/adv748x-csi2.c >> new file mode 100644 >> index 000000000000..a9b7fbd93530 >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x-csi2.c >> @@ -0,0 +1,323 @@ >> +/* >> + * Driver for Analog Devices ADV748X CSI-2 Transmitter >> + * >> + * Copyright (C) 2017 Renesas Electronics Corp. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms of the GNU General Public License as published by the >> + * Free Software Foundation; either version 2 of the License, or (at your >> + * option) any later version. >> + */ >> + >> +#include <linux/module.h> >> +#include <linux/mutex.h> >> + >> +#include <media/v4l2-ctrls.h> >> +#include <media/v4l2-device.h> >> +#include <media/v4l2-ioctl.h> >> + >> +#include "adv748x.h" >> + >> +static bool is_txa(struct adv748x_csi2 *tx) >> +{ >> + return tx == &tx->state->txa; >> +} >> + >> +static int adv748x_csi2_set_virtual_channel(struct adv748x_csi2 *tx, >> + unsigned int vc) >> +{ >> + return tx_write(tx, ADV748X_CSI_VC_REF, vc << ADV748X_CSI_VC_REF_SHIFT); >> +} >> + >> +/** >> + * adv748x_csi2_register_link : Register and link internal entities >> + * >> + * @tx: CSI2 private entity >> + * @v4l2_dev: Video registration device >> + * @src: Source subdevice to establish link >> + * @src_pad: Pad number of source to link to this @tx >> + * @preferred: Specify if this link is preferred over pre-existing links >> + * >> + * Ensure that the subdevice is registered against the v4l2_device, and link the >> + * source pad to the sink pad of the CSI2 bus entity. >> + */ >> +static int adv748x_csi2_register_link(struct adv748x_csi2 *tx, >> + struct v4l2_device *v4l2_dev, >> + struct v4l2_subdev *src, >> + unsigned int src_pad, >> + bool preferred) >> +{ >> + int enabled = 0; >> + int ret; >> + >> + if (preferred) >> + enabled = MEDIA_LNK_FL_ENABLED; >> + >> + if (!src->v4l2_dev) { >> + ret = v4l2_device_register_subdev(v4l2_dev, src); >> + if (ret) >> + return ret; >> + } >> + >> + return media_create_pad_link(&src->entity, src_pad, >> + &tx->sd.entity, ADV748X_CSI2_SINK, >> + enabled); >> +} >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_internal_ops >> + * >> + * We use the internal registered operation to be able to ensure that our >> + * incremental subdevices (not connected in the forward path) can be registered >> + * against the resulting video path and media device. >> + */ >> + >> +static int adv748x_csi2_registered(struct v4l2_subdev *sd) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct adv748x_state *state = tx->state; >> + int ret; >> + >> + adv_dbg(state, "Registered %s (%s)", is_txa(tx) ? "TXA":"TXB", >> + sd->name); >> + >> + ret = adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->afe.sd, >> + ADV748X_AFE_SOURCE, !is_txa(tx)); >> + if (ret) >> + return ret; >> + >> + /* TX-B only supports AFE */ >> + if (!is_txa(tx)) >> + return 0; >> + >> + return adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->hdmi.sd, >> + ADV748X_HDMI_SOURCE, true); >> +} >> + >> +static const struct v4l2_subdev_internal_ops adv748x_csi2_internal_ops = { >> + .registered = adv748x_csi2_registered, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_video_ops >> + */ >> + >> +static int adv748x_csi2_s_stream(struct v4l2_subdev *sd, int enable) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct v4l2_subdev *src; >> + >> + src = adv748x_get_remote_sd(&tx->pads[ADV748X_CSI2_SINK]); >> + if (!src) >> + return -EPIPE; >> + >> + return v4l2_subdev_call(src, video, s_stream, enable); >> +} >> + >> +static const struct v4l2_subdev_video_ops adv748x_csi2_video_ops = { >> + .s_stream = adv748x_csi2_s_stream, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_pad_ops >> + * >> + * The CSI2 bus pads are ignorant to the data sizes or formats. >> + * But we must support setting the pad formats for format propagation. >> + */ >> + >> +static struct v4l2_mbus_framefmt * >> +adv748x_csi2_get_pad_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + unsigned int pad, u32 which) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + >> + if (which == V4L2_SUBDEV_FORMAT_TRY) >> + return v4l2_subdev_get_try_format(sd, cfg, pad); >> + else > > 'else' is not needed. > >> + return &tx->format; >> +} >> + >> +static int adv748x_csi2_get_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct adv748x_state *state = tx->state; >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, >> + sdformat->which); >> + if (!mbusformat) >> + return -EINVAL; >> + >> + mutex_lock(&state->mutex); >> + >> + sdformat->format = *mbusformat; >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + >> +static int adv748x_csi2_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); >> + struct adv748x_state *state = tx->state; >> + struct v4l2_mbus_framefmt *mbusformat; >> + int ret = 0; >> + >> + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, >> + sdformat->which); >> + if (!mbusformat) >> + return -EINVAL; >> + >> + mutex_lock(&state->mutex); >> + >> + if (sdformat->pad == ADV748X_CSI2_SOURCE) { >> + const struct v4l2_mbus_framefmt *sink_fmt; >> + >> + sink_fmt = adv748x_csi2_get_pad_format(sd, cfg, >> + ADV748X_CSI2_SINK, >> + sdformat->which); >> + >> + if (!sink_fmt) { >> + ret = -EINVAL; >> + goto unlock; >> + } >> + >> + sdformat->format = *sink_fmt; >> + } >> + >> + *mbusformat = sdformat->format; >> + >> +unlock: >> + mutex_unlock(&state->mutex); >> + >> + return ret; >> +} >> + >> +static const struct v4l2_subdev_pad_ops adv748x_csi2_pad_ops = { >> + .get_fmt = adv748x_csi2_get_format, >> + .set_fmt = adv748x_csi2_set_format, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_ops >> + */ >> + >> +static const struct v4l2_subdev_ops adv748x_csi2_ops = { >> + .video = &adv748x_csi2_video_ops, >> + .pad = &adv748x_csi2_pad_ops, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * Subdev module and controls >> + */ >> + >> +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate) >> +{ >> + struct v4l2_ctrl *ctrl; >> + >> + ctrl = v4l2_ctrl_find(sd->ctrl_handler, V4L2_CID_PIXEL_RATE); >> + if (!ctrl) >> + return -EINVAL; >> + >> + return v4l2_ctrl_s_ctrl_int64(ctrl, rate); >> +} >> + >> +static int adv748x_csi2_s_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + switch (ctrl->id) { >> + case V4L2_CID_PIXEL_RATE: >> + return 0; >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static const struct v4l2_ctrl_ops adv748x_csi2_ctrl_ops = { >> + .s_ctrl = adv748x_csi2_s_ctrl, >> +}; >> + >> +static int adv748x_csi2_init_controls(struct adv748x_csi2 *tx) >> +{ >> + struct v4l2_ctrl *ctrl; >> + >> + v4l2_ctrl_handler_init(&tx->ctrl_hdl, 1); >> + >> + ctrl = v4l2_ctrl_new_std(&tx->ctrl_hdl, &adv748x_csi2_ctrl_ops, >> + V4L2_CID_PIXEL_RATE, 1, INT_MAX, 1, 1); >> + >> + tx->sd.ctrl_handler = &tx->ctrl_hdl; >> + if (tx->ctrl_hdl.error) { >> + v4l2_ctrl_handler_free(&tx->ctrl_hdl); >> + return tx->ctrl_hdl.error; >> + } >> + >> + return v4l2_ctrl_handler_setup(&tx->ctrl_hdl); >> +} >> + >> +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx) >> +{ >> + struct device_node *ep; >> + int ret; >> + >> + /* We can not use container_of to get back to the state with two TXs */ >> + tx->state = state; >> + tx->page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB; >> + >> + ep = state->endpoints[is_txa(tx) ? ADV748X_PORT_TXA : ADV748X_PORT_TXB]; >> + if (!ep) { >> + adv_err(state, "No endpoint found for %s\n", >> + is_txa(tx) ? "txa" : "txb"); >> + return -ENODEV; >> + } >> + >> + /* Initialise the virtual channel */ >> + adv748x_csi2_set_virtual_channel(tx, 0); >> + >> + adv748x_subdev_init(&tx->sd, state, &adv748x_csi2_ops, >> + MEDIA_ENT_F_UNKNOWN, >> + is_txa(tx) ? "txa" : "txb"); >> + >> + /* Ensure that matching is based upon the endpoint fwnodes */ >> + tx->sd.fwnode = of_fwnode_handle(ep); >> + >> + /* Register internal ops for incremental subdev registration */ >> + tx->sd.internal_ops = &adv748x_csi2_internal_ops; >> + >> + tx->pads[ADV748X_CSI2_SINK].flags = MEDIA_PAD_FL_SINK; >> + tx->pads[ADV748X_CSI2_SOURCE].flags = MEDIA_PAD_FL_SOURCE; >> + >> + ret = media_entity_pads_init(&tx->sd.entity, ADV748X_CSI2_NR_PADS, >> + tx->pads); >> + if (ret) >> + return ret; >> + >> + ret = adv748x_csi2_init_controls(tx); >> + if (ret) >> + goto err_free_media; >> + >> + ret = v4l2_async_register_subdev(&tx->sd); >> + if (ret) >> + goto err_free_ctrl; >> + >> + return 0; >> + >> +err_free_ctrl: >> + v4l2_ctrl_handler_free(&tx->ctrl_hdl); >> +err_free_media: >> + media_entity_cleanup(&tx->sd.entity); >> + >> + return ret; >> +} >> + >> +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx) >> +{ >> + v4l2_async_unregister_subdev(&tx->sd); >> + media_entity_cleanup(&tx->sd.entity); >> + v4l2_ctrl_handler_free(&tx->ctrl_hdl); >> +} >> diff --git a/drivers/media/i2c/adv748x/adv748x-hdmi.c >> b/drivers/media/i2c/adv748x/adv748x-hdmi.c >> new file mode 100644 >> index 000000000000..8f02c851bbc0 >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c >> @@ -0,0 +1,652 @@ >> +/* >> + * Driver for Analog Devices ADV748X HDMI receiver and Component Processor (CP) >> + * >> + * Copyright (C) 2017 Renesas Electronics Corp. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms of the GNU General Public License as published by the >> + * Free Software Foundation; either version 2 of the License, or (at your >> + * option) any later version. >> + */ >> + >> +#include <linux/module.h> >> +#include <linux/mutex.h> >> + >> +#include <media/v4l2-ctrls.h> >> +#include <media/v4l2-device.h> >> +#include <media/v4l2-dv-timings.h> >> +#include <media/v4l2-ioctl.h> >> + >> +#include <uapi/linux/v4l2-dv-timings.h> >> + >> +#include "adv748x.h" >> + >> +/* ----------------------------------------------------------------------------- >> + * HDMI and CP >> + */ >> + >> +#define ADV748X_HDMI_MIN_WIDTH 640 >> +#define ADV748X_HDMI_MAX_WIDTH 1920 >> +#define ADV748X_HDMI_MIN_HEIGHT 480 >> +#define ADV748X_HDMI_MAX_HEIGHT 1200 >> +#define ADV748X_HDMI_MIN_PIXELCLOCK 0 /* unknown */ > > I wouldn't use 0 for the min pixelclock. Pick something like 13000000 > instead (the lowest pixelclock rate for CEA timings, lowered by 0.5 MHz). Ack. I know no better, so I'm happy to use your value. > >> +#define ADV748X_HDMI_MAX_PIXELCLOCK 162000000 >> + >> +static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = { >> + .type = V4L2_DV_BT_656_1120, >> + /* keep this initialization for compatibility with GCC < 4.4.6 */ >> + .reserved = { 0 }, >> + /* Min pixelclock value is unknown */ >> + V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH, >> + ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT, >> + ADV748X_HDMI_MIN_PIXELCLOCK, >> + ADV748X_HDMI_MAX_PIXELCLOCK, >> + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT, >> + V4L2_DV_BT_CAP_INTERLACED | > > Has interlaced been tested? No ... /me ponders if the kit I have can be easily configured to test this. Is it better to remove the cap until tested ? > >> + V4L2_DV_BT_CAP_PROGRESSIVE) >> +}; >> + >> +struct adv748x_hdmi_video_standards { >> + struct v4l2_dv_timings timings; >> + u8 vid_std; >> + u8 v_freq; >> +}; >> + >> +static const struct adv748x_hdmi_video_standards >> +adv748x_hdmi_video_standards[] = { >> + { V4L2_DV_BT_CEA_720X480I59_94, 0x40, 0x00 }, >> + { V4L2_DV_BT_CEA_720X576I50, 0x41, 0x01 }, >> + { V4L2_DV_BT_CEA_720X480P59_94, 0x4a, 0x00 }, >> + { V4L2_DV_BT_CEA_720X576P50, 0x4b, 0x00 }, >> + { V4L2_DV_BT_CEA_1280X720P60, 0x53, 0x00 }, >> + { V4L2_DV_BT_CEA_1280X720P50, 0x53, 0x01 }, >> + { V4L2_DV_BT_CEA_1280X720P30, 0x53, 0x02 }, >> + { V4L2_DV_BT_CEA_1280X720P25, 0x53, 0x03 }, >> + { V4L2_DV_BT_CEA_1280X720P24, 0x53, 0x04 }, >> + { V4L2_DV_BT_CEA_1920X1080I60, 0x54, 0x00 }, >> + { V4L2_DV_BT_CEA_1920X1080I50, 0x54, 0x01 }, >> + { V4L2_DV_BT_CEA_1920X1080P60, 0x5e, 0x00 }, >> + { V4L2_DV_BT_CEA_1920X1080P50, 0x5e, 0x01 }, >> + { V4L2_DV_BT_CEA_1920X1080P30, 0x5e, 0x02 }, >> + { V4L2_DV_BT_CEA_1920X1080P25, 0x5e, 0x03 }, >> + { V4L2_DV_BT_CEA_1920X1080P24, 0x5e, 0x04 }, >> + /* SVGA */ >> + { V4L2_DV_BT_DMT_800X600P56, 0x80, 0x00 }, >> + { V4L2_DV_BT_DMT_800X600P60, 0x81, 0x00 }, >> + { V4L2_DV_BT_DMT_800X600P72, 0x82, 0x00 }, >> + { V4L2_DV_BT_DMT_800X600P75, 0x83, 0x00 }, >> + { V4L2_DV_BT_DMT_800X600P85, 0x84, 0x00 }, >> + /* SXGA */ >> + { V4L2_DV_BT_DMT_1280X1024P60, 0x85, 0x00 }, >> + { V4L2_DV_BT_DMT_1280X1024P75, 0x86, 0x00 }, >> + /* VGA */ >> + { V4L2_DV_BT_DMT_640X480P60, 0x88, 0x00 }, >> + { V4L2_DV_BT_DMT_640X480P72, 0x89, 0x00 }, >> + { V4L2_DV_BT_DMT_640X480P75, 0x8a, 0x00 }, >> + { V4L2_DV_BT_DMT_640X480P85, 0x8b, 0x00 }, >> + /* XGA */ >> + { V4L2_DV_BT_DMT_1024X768P60, 0x8c, 0x00 }, >> + { V4L2_DV_BT_DMT_1024X768P70, 0x8d, 0x00 }, >> + { V4L2_DV_BT_DMT_1024X768P75, 0x8e, 0x00 }, >> + { V4L2_DV_BT_DMT_1024X768P85, 0x8f, 0x00 }, >> + /* UXGA */ >> + { V4L2_DV_BT_DMT_1600X1200P60, 0x96, 0x00 }, >> +}; >> + >> +static void adv748x_hdmi_fill_format(struct adv748x_hdmi *hdmi, >> + struct v4l2_mbus_framefmt *fmt) >> +{ >> + memset(fmt, 0, sizeof(*fmt)); >> + >> + fmt->code = MEDIA_BUS_FMT_RGB888_1X24; >> + fmt->colorspace = V4L2_COLORSPACE_SRGB; > > It's OK for now, but the colorspace depends on the AVI InfoFrame contents. > Add some comment stating this. Added. >> + fmt->field = hdmi->timings.bt.interlaced ? >> + V4L2_FIELD_INTERLACED : V4L2_FIELD_NONE; >> + >> + fmt->width = hdmi->timings.bt.width; >> + fmt->height = hdmi->timings.bt.height; >> +} >> + >> +static void adv748x_fill_optional_dv_timings(struct v4l2_dv_timings *timings) >> +{ >> + v4l2_find_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, >> + 250000, NULL, NULL); >> +} >> + >> +static bool adv748x_hdmi_has_signal(struct adv748x_state *state) >> +{ >> + int val; >> + >> + /* Check that VERT_FILTER and DE_REGEN is locked */ >> + val = hdmi_read(state, ADV748X_HDMI_LW1); >> + return (val & ADV748X_HDMI_LW1_VERT_FILTER) && >> + (val & ADV748X_HDMI_LW1_DE_REGEN); >> +} >> + >> +static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state) >> +{ >> + int a, b; >> + >> + a = hdmi_read(state, ADV748X_HDMI_TMDS_1); >> + b = hdmi_read(state, ADV748X_HDMI_TMDS_2); >> + if (a < 0 || b < 0) >> + return -ENODATA; >> + >> + /* >> + * The High 9 bits store TMDS frequency measurement in MHz >> + * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency >> + * measurement in 1/128 MHz >> + */ >> + return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128; >> +} >> + >> +/* >> + * adv748x_hdmi_set_de_timings: Adjust horizontal picture offset through DE >> + * >> + * HDMI CP uses a Data Enable synchronisation timing reference >> + * >> + * Vary the leading and trailing edge position of the DE signal output by the CP >> + * core. Values are stored as signed-twos-complement in one-pixel-clock units >> + * >> + * The start and end are shifted equally by the 10-bit shift value. >> + */ >> +static void adv748x_hdmi_set_de_timings(struct adv748x_state *state, int shift) >> +{ >> + u8 high, low; >> + >> + /* POS_HIGH stores bits 8 and 9 of both the start and end */ >> + high = ADV748X_CP_DE_POS_HIGH_SET; >> + high |= (shift & 0x300) >> 8; >> + low = shift & 0xff; >> + >> + /* The sequence of the writes is important and must be followed */ >> + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); >> + cp_write(state, ADV748X_CP_DE_POS_END_LOW, low); >> + >> + high |= (shift & 0x300) >> 6; >> + >> + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); >> + cp_write(state, ADV748X_CP_DE_POS_START_LOW, low); >> +} >> + >> +static int adv748x_hdmi_set_video_timings(struct adv748x_state *state, >> + const struct v4l2_dv_timings *timings) >> +{ >> + const struct adv748x_hdmi_video_standards *stds = >> + adv748x_hdmi_video_standards; >> + unsigned int i; >> + >> + for (i = 0; i < ARRAY_SIZE(adv748x_hdmi_video_standards); i++) { >> + if (!v4l2_match_dv_timings(timings, &stds[i].timings, 250000, >> + false)) >> + continue; >> + } >> + >> + if (i >= ARRAY_SIZE(adv748x_hdmi_video_standards)) >> + return -EINVAL; >> + >> + /* >> + * When setting cp_vid_std to either 720p, 1080i, or 1080p, the video >> + * will get shifted horizontally to the left in active video mode. >> + * The de_h_start and de_h_end controls are used to centre the picture >> + * correctly >> + */ >> + switch (stds[i].vid_std) { >> + case 0x53: /* 720p */ >> + adv748x_hdmi_set_de_timings(state, -40); >> + break; >> + case 0x54: /* 1080i */ >> + case 0x5e: /* 1080p */ >> + adv748x_hdmi_set_de_timings(state, -44); >> + break; >> + default: >> + adv748x_hdmi_set_de_timings(state, 0); >> + break; >> + } >> + >> + io_write(state, ADV748X_IO_VID_STD, stds[i].vid_std); >> + io_clrset(state, ADV748X_IO_DATAPATH, ADV748X_IO_DATAPATH_VFREQ_M, >> + stds[i].v_freq << ADV748X_IO_DATAPATH_VFREQ_SHIFT); >> + >> + return 0; >> +} >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_video_ops >> + */ >> + >> +static int adv748x_hdmi_s_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings *timings) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + int ret; >> + >> + if (!timings) >> + return -EINVAL; >> + >> + if (v4l2_match_dv_timings(&hdmi->timings, timings, 0, false)) >> + return 0; >> + >> + if (!v4l2_valid_dv_timings(timings, &adv748x_hdmi_timings_cap, >> + NULL, NULL)) >> + return -ERANGE; >> + >> + adv748x_fill_optional_dv_timings(timings); >> + >> + mutex_lock(&state->mutex); >> + >> + ret = adv748x_hdmi_set_video_timings(state, timings); >> + if (ret) >> + goto error; >> + >> + hdmi->timings = *timings; >> + >> + cp_clrset(state, ADV748X_CP_VID_ADJ_2, ADV748X_CP_VID_ADJ_2_INTERLACED, >> + timings->bt.interlaced ? >> + ADV748X_CP_VID_ADJ_2_INTERLACED : 0); >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> + >> +error: >> + mutex_unlock(&state->mutex); >> + return ret; >> +} >> + >> +static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings *timings) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + >> + mutex_lock(&state->mutex); >> + >> + *timings = hdmi->timings; >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings *timings) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + struct v4l2_bt_timings *bt = &timings->bt; >> + int pixelclock; >> + int polarity; >> + >> + if (!timings) >> + return -EINVAL; >> + >> + memset(timings, 0, sizeof(struct v4l2_dv_timings)); >> + >> + if (!adv748x_hdmi_has_signal(state)) >> + return -ENOLINK; >> + >> + pixelclock = adv748x_hdmi_read_pixelclock(state); >> + if (pixelclock < 0) >> + return -ENODATA; >> + >> + timings->type = V4L2_DV_BT_656_1120; >> + >> + bt->pixelclock = pixelclock; >> + bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) & >> + ADV748X_HDMI_F1H1_INTERLACED ? >> + V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; >> + bt->width = hdmi_read16(state, ADV748X_HDMI_LW1, >> + ADV748X_HDMI_LW1_WIDTH_MASK); >> + bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1, >> + ADV748X_HDMI_F0H1_HEIGHT_MASK); >> + bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH, >> + ADV748X_HDMI_HFRONT_PORCH_MASK); >> + bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH, >> + ADV748X_HDMI_HSYNC_WIDTH_MASK); >> + bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH, >> + ADV748X_HDMI_HBACK_PORCH_MASK); >> + bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH, >> + ADV748X_HDMI_VFRONT_PORCH_MASK) / 2; >> + bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH, >> + ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2; >> + bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH, >> + ADV748X_HDMI_VBACK_PORCH_MASK) / 2; >> + >> + >> + polarity = hdmi_read(state, 0x05); >> + bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) | >> + (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0); >> + >> + if (bt->interlaced == V4L2_DV_INTERLACED) { >> + bt->height += hdmi_read16(state, 0x0b, 0x1fff); >> + bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2; >> + bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2; >> + bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2; >> + } >> + >> + adv748x_fill_optional_dv_timings(timings); >> + >> + /* >> + * No interrupt handling is implemented yet. >> + * There should be an IRQ when a cable is plugged and the new timings >> + * should be figured out and stored to state. >> + */ >> + hdmi->timings = *timings; >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + >> + mutex_lock(&state->mutex); >> + >> + *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL; > > It would be nice if this could be a bit more detailed. Esp. being able to tell the > difference between whether or not there is a signal, and whether or not the > signal is stable (i.e. has sync). Ack. > >> + >> + mutex_unlock(&state->mutex); >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_s_stream(struct v4l2_subdev *sd, int enable) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + int ret; >> + >> + mutex_lock(&state->mutex); >> + >> + ret = adv748x_txa_power(state, enable); >> + if (ret) >> + goto done; >> + >> + if (adv748x_hdmi_has_signal(state)) >> + adv_dbg(state, "Detected HDMI signal\n"); >> + else >> + adv_dbg(state, "Couldn't detect HDMI video signal\n"); >> + >> +done: >> + mutex_unlock(&state->mutex); >> + return ret; >> +} >> + >> +static int adv748x_hdmi_g_pixelaspect(struct v4l2_subdev *sd, >> + struct v4l2_fract *aspect) >> +{ >> + aspect->numerator = 1; >> + aspect->denominator = 1; >> + >> + return 0; >> +} >> + >> +static const struct v4l2_subdev_video_ops adv748x_video_ops_hdmi = { >> + .s_dv_timings = adv748x_hdmi_s_dv_timings, >> + .g_dv_timings = adv748x_hdmi_g_dv_timings, >> + .query_dv_timings = adv748x_hdmi_query_dv_timings, >> + .g_input_status = adv748x_hdmi_g_input_status, >> + .s_stream = adv748x_hdmi_s_stream, >> + .g_pixelaspect = adv748x_hdmi_g_pixelaspect, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_pad_ops >> + */ >> + >> +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) >> +{ >> + struct v4l2_subdev *tx; >> + struct v4l2_dv_timings timings; >> + struct v4l2_bt_timings *bt = &timings.bt; >> + unsigned int fps; >> + >> + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); >> + if (!tx) >> + return -ENOLINK; >> + >> + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); >> + >> + fps = DIV_ROUND_CLOSEST(bt->pixelclock, >> + V4L2_DV_BT_FRAME_WIDTH(bt) * >> + V4L2_DV_BT_FRAME_HEIGHT(bt)); >> + >> + return adv748x_csi2_set_pixelrate(tx, bt->width * bt->height * fps); >> +} >> + >> +static int adv748x_hdmi_enum_mbus_code(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_mbus_code_enum *code) >> +{ >> + if (code->index != 0) >> + return -EINVAL; >> + >> + code->code = MEDIA_BUS_FMT_RGB888_1X24; >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_get_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + if (sdformat->pad != ADV748X_HDMI_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + sdformat->format = *mbusformat; >> + } else { >> + adv748x_hdmi_fill_format(hdmi, &sdformat->format); >> + adv748x_hdmi_set_pixelrate(hdmi); >> + } >> + >> + return 0; >> +} >> + >> +static int adv748x_hdmi_set_format(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *sdformat) >> +{ >> + struct v4l2_mbus_framefmt *mbusformat; >> + >> + if (sdformat->pad != ADV748X_HDMI_SOURCE) >> + return -EINVAL; >> + >> + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) >> + return adv748x_hdmi_get_format(sd, cfg, sdformat); >> + >> + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); >> + *mbusformat = sdformat->format; >> + >> + return 0; >> +} >> + >> +static bool adv748x_hdmi_check_dv_timings(const struct v4l2_dv_timings *timings, >> + void *hdl) >> +{ >> + const struct adv748x_hdmi_video_standards *stds = >> + adv748x_hdmi_video_standards; >> + unsigned int i; >> + >> + for (i = 0; stds[i].timings.bt.width; i++) >> + if (v4l2_match_dv_timings(timings, &stds[i].timings, 0, false)) >> + return true; >> + >> + return false; >> +} >> + >> +static int adv748x_hdmi_enum_dv_timings(struct v4l2_subdev *sd, >> + struct v4l2_enum_dv_timings *timings) >> +{ >> + return v4l2_enum_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, >> + adv748x_hdmi_check_dv_timings, NULL); >> +} >> + >> +static int adv748x_hdmi_dv_timings_cap(struct v4l2_subdev *sd, >> + struct v4l2_dv_timings_cap *cap) >> +{ >> + *cap = adv748x_hdmi_timings_cap; >> + return 0; >> +} >> + >> +static const struct v4l2_subdev_pad_ops adv748x_pad_ops_hdmi = { >> + .enum_mbus_code = adv748x_hdmi_enum_mbus_code, >> + .set_fmt = adv748x_hdmi_set_format, >> + .get_fmt = adv748x_hdmi_get_format, >> + .dv_timings_cap = adv748x_hdmi_dv_timings_cap, >> + .enum_dv_timings = adv748x_hdmi_enum_dv_timings, > > No get/set_edid ops? How can you use HDMI without having these ops? -EWORKSFORME. Just kidding ... The input devices I have connected just work it would seem. As far as I can tell, the default EDID map from the hardware is basically a zero table - but with the hardware providing a valid checksum to state that it's OK or something... The input devices I have just output a configured signal regardless perhaps. I've now implemented and tested EDID support. I'm using a custom utility from Laurent to program the EDID through the subdev directly. (It would be nice to be able to use v4l2-ctl here, so that's on my radar - but I don't have time right now ). > >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * v4l2_subdev_ops >> + */ >> + >> +static const struct v4l2_subdev_ops adv748x_ops_hdmi = { >> + .video = &adv748x_video_ops_hdmi, >> + .pad = &adv748x_pad_ops_hdmi, >> +}; >> + >> +/* ----------------------------------------------------------------------------- >> + * Controls >> + */ >> + >> +static const char * const hdmi_ctrl_patgen_menu[] = { >> + "Disabled", >> + "Plain Blue", > > I'd say just "Blue" or possibly "Solid Blue". Ok, again - that text is directly from the data sheet. This one isn't configurable though AFAICS > >> + "Color Bars", >> + "Ramp Grey", >> + "Ramp Blue", >> + "Ramp Red", This actually bugged me as they've inverted the location of the word 'Ramp' here vs AFE ... >> + "Checkered" > > I assume this is a black and white pattern? If so, say: "B&W Checkered" I can't remember so I'll reload it and see - then set as appropriate. > >> +}; >> + >> +static int adv748x_hdmi_s_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct adv748x_hdmi *hdmi = adv748x_ctrl_to_hdmi(ctrl); >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + int ret; >> + u8 pattern; >> + >> + /* Enable video adjustment first */ >> + ret = cp_clrset(state, ADV748X_CP_VID_ADJ, >> + ADV748X_CP_VID_ADJ_ENABLE, >> + ADV748X_CP_VID_ADJ_ENABLE); >> + if (ret < 0) >> + return ret; >> + >> + switch (ctrl->id) { >> + case V4L2_CID_BRIGHTNESS: >> + ret = cp_write(state, ADV748X_CP_BRI, ctrl->val); >> + break; >> + case V4L2_CID_HUE: >> + ret = cp_write(state, ADV748X_CP_HUE, ctrl->val); >> + break; >> + case V4L2_CID_CONTRAST: >> + ret = cp_write(state, ADV748X_CP_CON, ctrl->val); >> + break; >> + case V4L2_CID_SATURATION: >> + ret = cp_write(state, ADV748X_CP_SAT, ctrl->val); >> + break; >> + case V4L2_CID_TEST_PATTERN: >> + pattern = ctrl->val; >> + >> + /* Pattern is 0-indexed. Ctrl Menu is 1-indexed */ >> + if (pattern) { >> + pattern--; >> + pattern |= ADV748X_CP_PAT_GEN_EN; >> + } >> + >> + ret = cp_write(state, ADV748X_CP_PAT_GEN, pattern); >> + >> + break; >> + default: >> + return -EINVAL; >> + } >> + >> + return ret; >> +} >> + >> +static const struct v4l2_ctrl_ops adv748x_hdmi_ctrl_ops = { >> + .s_ctrl = adv748x_hdmi_s_ctrl, >> +}; >> + >> +static int adv748x_hdmi_init_controls(struct adv748x_hdmi *hdmi) >> +{ >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + >> + v4l2_ctrl_handler_init(&hdmi->ctrl_hdl, 5); >> + >> + /* Use our mutex for the controls */ >> + hdmi->ctrl_hdl.lock = &state->mutex; >> + >> + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >> + V4L2_CID_BRIGHTNESS, ADV748X_CP_BRI_MIN, >> + ADV748X_CP_BRI_MAX, 1, ADV748X_CP_BRI_DEF); >> + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >> + V4L2_CID_CONTRAST, ADV748X_CP_CON_MIN, >> + ADV748X_CP_CON_MAX, 1, ADV748X_CP_CON_DEF); >> + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >> + V4L2_CID_SATURATION, ADV748X_CP_SAT_MIN, >> + ADV748X_CP_SAT_MAX, 1, ADV748X_CP_SAT_DEF); >> + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >> + V4L2_CID_HUE, ADV748X_CP_HUE_MIN, >> + ADV748X_CP_HUE_MAX, 1, ADV748X_CP_HUE_DEF); > > You should implement the V4L2_CID_DV_RX_POWER_PRESENT control as well, > once interrupts are working. > > Perhaps add a comment as a reminder? I have a separate patch where I've started looking at interrupts, but I've put a comment in here too. Is this just to provide connection hotplug events to userspace? > >> + >> + v4l2_ctrl_new_std_menu_items(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >> + V4L2_CID_TEST_PATTERN, >> + ARRAY_SIZE(hdmi_ctrl_patgen_menu) - 1, >> + 0, 0, hdmi_ctrl_patgen_menu); >> + >> + hdmi->sd.ctrl_handler = &hdmi->ctrl_hdl; >> + if (hdmi->ctrl_hdl.error) { >> + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); >> + return hdmi->ctrl_hdl.error; >> + } >> + >> + return v4l2_ctrl_handler_setup(&hdmi->ctrl_hdl); >> +} >> + >> +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi) >> +{ >> + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); >> + static const struct v4l2_dv_timings cea720x480 = >> + V4L2_DV_BT_CEA_720X480I59_94; >> + int ret; >> + >> + hdmi->timings = cea720x480; >> + >> + adv748x_subdev_init(&hdmi->sd, state, &adv748x_ops_hdmi, >> + MEDIA_ENT_F_IO_DTV, "hdmi"); >> + >> + hdmi->pads[ADV748X_HDMI_SINK].flags = MEDIA_PAD_FL_SINK; >> + hdmi->pads[ADV748X_HDMI_SOURCE].flags = MEDIA_PAD_FL_SOURCE; >> + >> + ret = media_entity_pads_init(&hdmi->sd.entity, >> + ADV748X_HDMI_NR_PADS, hdmi->pads); >> + if (ret) >> + return ret; >> + >> + ret = adv748x_hdmi_init_controls(hdmi); >> + if (ret) >> + goto err_free_media; >> + >> + return 0; >> + >> +err_free_media: >> + media_entity_cleanup(&hdmi->sd.entity); >> + >> + return ret; >> +} >> + >> +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi) >> +{ >> + v4l2_device_unregister_subdev(&hdmi->sd); >> + media_entity_cleanup(&hdmi->sd.entity); >> + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); >> +} >> diff --git a/drivers/media/i2c/adv748x/adv748x.h >> b/drivers/media/i2c/adv748x/adv748x.h >> new file mode 100644 >> index 000000000000..2f36e5052f08 >> --- /dev/null >> +++ b/drivers/media/i2c/adv748x/adv748x.h >> @@ -0,0 +1,415 @@ >> +/* >> + * Driver for Analog Devices ADV748X video decoder and HDMI receiver >> + * >> + * Copyright (C) 2017 Renesas Electronics Corp. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms of the GNU General Public License as published by the >> + * Free Software Foundation; either version 2 of the License, or (at your >> + * option) any later version. >> + * >> + * Authors: >> + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> >> + * Niklas Söderlund <niklas.soderlund@ragnatech.se> >> + * Kieran Bingham <kieran.bingham@ideasonboard.com> >> + * >> + * The ADV748x range of receivers have the following configurations: >> + * >> + * Analog HDMI MHL 4-Lane 1-Lane >> + * In In CSI CSI >> + * ADV7480 X X X >> + * ADV7481 X X X X X >> + * ADV7482 X X X X >> + */ >> + >> +#include <linux/i2c.h> >> + >> +#ifndef _ADV748X_H_ >> +#define _ADV748X_H_ >> + >> +/* I2C slave addresses */ >> +#define ADV748X_I2C_IO 0x70 /* IO Map */ >> +#define ADV748X_I2C_DPLL 0x26 /* DPLL Map */ >> +#define ADV748X_I2C_CP 0x22 /* CP Map */ >> +#define ADV748X_I2C_HDMI 0x34 /* HDMI Map */ >> +#define ADV748X_I2C_EDID 0x36 /* EDID Map */ >> +#define ADV748X_I2C_REPEATER 0x32 /* HDMI RX Repeater Map */ >> +#define ADV748X_I2C_INFOFRAME 0x31 /* HDMI RX InfoFrame Map */ >> +#define ADV748X_I2C_CEC 0x41 /* CEC Map */ >> +#define ADV748X_I2C_SDP 0x79 /* SDP Map */ >> +#define ADV748X_I2C_TXB 0x48 /* CSI-TXB Map */ >> +#define ADV748X_I2C_TXA 0x4a /* CSI-TXA Map */ >> + >> +enum adv748x_page { >> + ADV748X_PAGE_IO, >> + ADV748X_PAGE_DPLL, >> + ADV748X_PAGE_CP, >> + ADV748X_PAGE_HDMI, >> + ADV748X_PAGE_EDID, >> + ADV748X_PAGE_REPEATER, >> + ADV748X_PAGE_INFOFRAME, >> + ADV748X_PAGE_CEC, >> + ADV748X_PAGE_SDP, >> + ADV748X_PAGE_TXB, >> + ADV748X_PAGE_TXA, >> + ADV748X_PAGE_MAX, >> + >> + /* Fake pages for register sequences */ >> + ADV748X_PAGE_WAIT, /* Wait x msec */ >> + ADV748X_PAGE_EOR, /* End Mark */ >> +}; >> + >> +/** >> + * enum adv748x_ports - Device tree port number definitions >> + * >> + * The ADV748X ports define the mapping between subdevices >> + * and the device tree specification >> + */ >> +enum adv748x_ports { >> + ADV748X_PORT_AIN0 = 0, >> + ADV748X_PORT_AIN1 = 1, >> + ADV748X_PORT_AIN2 = 2, >> + ADV748X_PORT_AIN3 = 3, >> + ADV748X_PORT_AIN4 = 4, >> + ADV748X_PORT_AIN5 = 5, >> + ADV748X_PORT_AIN6 = 6, >> + ADV748X_PORT_AIN7 = 7, >> + ADV748X_PORT_HDMI = 8, >> + ADV748X_PORT_TTL = 9, >> + ADV748X_PORT_TXA = 10, >> + ADV748X_PORT_TXB = 11, >> + ADV748X_PORT_MAX = 12, >> +}; >> + >> +enum adv748x_csi2_pads { >> + ADV748X_CSI2_SINK, >> + ADV748X_CSI2_SOURCE, >> + ADV748X_CSI2_NR_PADS, >> +}; >> + >> +/* CSI2 transmitters can have 2 internal connections, HDMI/AFE */ >> +#define ADV748X_CSI2_MAX_SUBDEVS 2 >> + >> +struct adv748x_csi2 { >> + struct adv748x_state *state; >> + struct v4l2_mbus_framefmt format; >> + unsigned int page; >> + >> + struct media_pad pads[ADV748X_CSI2_NR_PADS]; >> + struct v4l2_ctrl_handler ctrl_hdl; >> + struct v4l2_subdev sd; >> +}; >> + >> +#define notifier_to_csi2(n) container_of(n, struct adv748x_csi2, notifier) >> +#define adv748x_sd_to_csi2(sd) container_of(sd, struct adv748x_csi2, sd) >> + >> +enum adv748x_hdmi_pads { >> + ADV748X_HDMI_SINK, >> + ADV748X_HDMI_SOURCE, >> + ADV748X_HDMI_NR_PADS, >> +}; >> + >> +struct adv748x_hdmi { >> + struct media_pad pads[ADV748X_HDMI_NR_PADS]; >> + struct v4l2_ctrl_handler ctrl_hdl; >> + struct v4l2_subdev sd; >> + struct v4l2_mbus_framefmt format; >> + >> + struct v4l2_dv_timings timings; >> +}; >> + >> +#define adv748x_ctrl_to_hdmi(ctrl) \ >> + container_of(ctrl->handler, struct adv748x_hdmi, ctrl_hdl) >> +#define adv748x_sd_to_hdmi(sd) container_of(sd, struct adv748x_hdmi, sd) >> + >> +enum adv748x_afe_pads { >> + ADV748X_AFE_SINK_AIN0, >> + ADV748X_AFE_SINK_AIN1, >> + ADV748X_AFE_SINK_AIN2, >> + ADV748X_AFE_SINK_AIN3, >> + ADV748X_AFE_SINK_AIN4, >> + ADV748X_AFE_SINK_AIN5, >> + ADV748X_AFE_SINK_AIN6, >> + ADV748X_AFE_SINK_AIN7, >> + ADV748X_AFE_SOURCE, >> + ADV748X_AFE_NR_PADS, >> +}; >> + >> +struct adv748x_afe { >> + struct media_pad pads[ADV748X_AFE_NR_PADS]; >> + struct v4l2_ctrl_handler ctrl_hdl; >> + struct v4l2_subdev sd; >> + struct v4l2_mbus_framefmt format; >> + >> + bool streaming; >> + v4l2_std_id curr_norm; >> + unsigned int input; >> +}; >> + >> +#define adv748x_ctrl_to_afe(ctrl) \ >> + container_of(ctrl->handler, struct adv748x_afe, ctrl_hdl) >> +#define adv748x_sd_to_afe(sd) container_of(sd, struct adv748x_afe, sd) >> + >> +/** >> + * struct adv748x_state - State of ADV748X >> + * @dev: (OF) device >> + * @client: I2C client >> + * @mutex: protect global state >> + * >> + * @endpoints: parsed device node endpoints for each port >> + * >> + * @i2c_addresses I2C Page addresses >> + * @i2c_clients I2C clients for the page accesses >> + * @regmap regmap configuration pages. >> + * >> + * @hdmi: state of HDMI receiver context >> + * @afe: state of AFE receiver context >> + * @txa: state of TXA transmitter context >> + * @txb: state of TXB transmitter context >> + */ >> +struct adv748x_state { >> + struct device *dev; >> + struct i2c_client *client; >> + struct mutex mutex; >> + >> + struct device_node *endpoints[ADV748X_PORT_MAX]; >> + >> + struct i2c_client *i2c_clients[ADV748X_PAGE_MAX]; >> + struct regmap *regmap[ADV748X_PAGE_MAX]; >> + >> + struct adv748x_hdmi hdmi; >> + struct adv748x_afe afe; >> + struct adv748x_csi2 txa; >> + struct adv748x_csi2 txb; >> +}; >> + >> +#define adv748x_hdmi_to_state(h) container_of(h, struct adv748x_state, hdmi) >> +#define adv748x_afe_to_state(a) container_of(a, struct adv748x_state, afe) >> + >> +#define adv_err(a, fmt, arg...) dev_err(a->dev, fmt, ##arg) >> +#define adv_info(a, fmt, arg...) dev_info(a->dev, fmt, ##arg) >> +#define adv_dbg(a, fmt, arg...) dev_dbg(a->dev, fmt, ##arg) >> + >> +/* Register Mappings */ >> + >> +/* IO Map */ >> +#define ADV748X_IO_PD 0x00 /* power down controls */ >> +#define ADV748X_IO_PD_RX_EN BIT(6) >> + >> +#define ADV748X_IO_REG_04 0x04 >> +#define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */ >> + >> +#define ADV748X_IO_DATAPATH 0x03 /* datapath cntrl */ >> +#define ADV748X_IO_DATAPATH_VFREQ_M 0x70 >> +#define ADV748X_IO_DATAPATH_VFREQ_SHIFT 4 >> + >> +#define ADV748X_IO_VID_STD 0x05 >> + >> +#define ADV748X_IO_10 0x10 /* io_reg_10 */ >> +#define ADV748X_IO_10_CSI4_EN BIT(7) >> +#define ADV748X_IO_10_CSI1_EN BIT(6) >> +#define ADV748X_IO_10_PIX_OUT_EN BIT(5) >> + >> +#define ADV748X_IO_CHIP_REV_ID_1 0xdf >> +#define ADV748X_IO_CHIP_REV_ID_2 0xe0 >> + >> +#define ADV748X_IO_SLAVE_ADDR_BASE 0xf2 >> + >> +/* HDMI RX Map */ >> +#define ADV748X_HDMI_LW1 0x07 /* line width_1 */ >> +#define ADV748X_HDMI_LW1_VERT_FILTER BIT(7) >> +#define ADV748X_HDMI_LW1_DE_REGEN BIT(5) >> +#define ADV748X_HDMI_LW1_WIDTH_MASK 0x1fff >> + >> +#define ADV748X_HDMI_F0H1 0x09 /* field0 height_1 */ >> +#define ADV748X_HDMI_F0H1_HEIGHT_MASK 0x1fff >> + >> +#define ADV748X_HDMI_F1H1 0x0b /* field1 height_1 */ >> +#define ADV748X_HDMI_F1H1_INTERLACED BIT(5) >> + >> +#define ADV748X_HDMI_HFRONT_PORCH 0x20 /* hsync_front_porch_1 */ >> +#define ADV748X_HDMI_HFRONT_PORCH_MASK 0x1fff >> + >> +#define ADV748X_HDMI_HSYNC_WIDTH 0x22 /* hsync_pulse_width_1 */ >> +#define ADV748X_HDMI_HSYNC_WIDTH_MASK 0x1fff >> + >> +#define ADV748X_HDMI_HBACK_PORCH 0x24 /* hsync_back_porch_1 */ >> +#define ADV748X_HDMI_HBACK_PORCH_MASK 0x1fff >> + >> +#define ADV748X_HDMI_VFRONT_PORCH 0x2a /* field0_vs_front_porch_1 */ >> +#define ADV748X_HDMI_VFRONT_PORCH_MASK 0x3fff >> + >> +#define ADV748X_HDMI_VSYNC_WIDTH 0x2e /* field0_vs_pulse_width_1 */ >> +#define ADV748X_HDMI_VSYNC_WIDTH_MASK 0x3fff >> + >> +#define ADV748X_HDMI_VBACK_PORCH 0x32 /* field0_vs_back_porch_1 */ >> +#define ADV748X_HDMI_VBACK_PORCH_MASK 0x3fff >> + >> +#define ADV748X_HDMI_TMDS_1 0x51 /* hdmi_reg_51 */ >> +#define ADV748X_HDMI_TMDS_2 0x52 /* hdmi_reg_52 */ >> + >> +/* SDP Main Map */ >> +#define ADV748X_SDP_INSEL 0x00 /* user_map_rw_reg_00 */ >> + >> +#define ADV748X_SDP_VID_SEL 0x02 /* user_map_rw_reg_02 */ >> +#define ADV748X_SDP_VID_SEL_MASK 0xf0 >> +#define ADV748X_SDP_VID_SEL_SHIFT 4 >> + >> +/* Contrast - Unsigned*/ >> +#define ADV748X_SDP_CON 0x08 /* user_map_rw_reg_08 */ >> +#define ADV748X_SDP_CON_MIN 0 >> +#define ADV748X_SDP_CON_DEF 128 >> +#define ADV748X_SDP_CON_MAX 255 >> + >> +/* Brightness - Signed */ >> +#define ADV748X_SDP_BRI 0x0a /* user_map_rw_reg_0a */ >> +#define ADV748X_SDP_BRI_MIN -128 >> +#define ADV748X_SDP_BRI_DEF 0 >> +#define ADV748X_SDP_BRI_MAX 127 >> + >> +/* Hue - Signed, inverted*/ >> +#define ADV748X_SDP_HUE 0x0b /* user_map_rw_reg_0b */ >> +#define ADV748X_SDP_HUE_MIN -127 >> +#define ADV748X_SDP_HUE_DEF 0 >> +#define ADV748X_SDP_HUE_MAX 128 >> + >> +/* Test Patterns / Default Values */ >> +#define ADV748X_SDP_DEF 0x0c /* user_map_rw_reg_0c */ >> +#define ADV748X_SDP_DEF_VAL_EN BIT(0) /* Force free run mode */ >> +#define ADV748X_SDP_DEF_VAL_AUTO_EN BIT(1) /* Free run when no signal */ >> + >> +#define ADV748X_SDP_MAP_SEL 0x0e /* user_map_rw_reg_0e */ >> +#define ADV748X_SDP_MAP_SEL_RO_MAIN 1 >> + >> +/* Free run pattern select */ >> +#define ADV748X_SDP_FRP 0x14 >> +#define ADV748X_SDP_FRP_MASK GENMASK(3, 1) >> + >> +/* Saturation */ >> +#define ADV748X_SDP_SD_SAT_U 0xe3 /* user_map_rw_reg_e3 */ >> +#define ADV748X_SDP_SD_SAT_V 0xe4 /* user_map_rw_reg_e4 */ >> +#define ADV748X_SDP_SAT_MIN 0 >> +#define ADV748X_SDP_SAT_DEF 128 >> +#define ADV748X_SDP_SAT_MAX 255 >> + >> +/* SDP RO Main Map */ >> +#define ADV748X_SDP_RO_10 0x10 >> +#define ADV748X_SDP_RO_10_IN_LOCK BIT(0) >> + >> +/* CP Map */ >> +#define ADV748X_CP_PAT_GEN 0x37 /* int_pat_gen_1 */ >> +#define ADV748X_CP_PAT_GEN_EN BIT(7) >> + >> +/* Contrast Control - Unsigned */ >> +#define ADV748X_CP_CON 0x3a /* contrast_cntrl */ >> +#define ADV748X_CP_CON_MIN 0 /* Minimum contrast */ >> +#define ADV748X_CP_CON_DEF 128 /* Default */ >> +#define ADV748X_CP_CON_MAX 255 /* Maximum contrast */ >> + >> +/* Saturation Control - Unsigned */ >> +#define ADV748X_CP_SAT 0x3b /* saturation_cntrl */ >> +#define ADV748X_CP_SAT_MIN 0 /* Minimum saturation */ >> +#define ADV748X_CP_SAT_DEF 128 /* Default */ >> +#define ADV748X_CP_SAT_MAX 255 /* Maximum saturation */ >> + >> +/* Brightness Control - Signed */ >> +#define ADV748X_CP_BRI 0x3c /* brightness_cntrl */ >> +#define ADV748X_CP_BRI_MIN -128 /* Luma is -512d */ >> +#define ADV748X_CP_BRI_DEF 0 /* Luma is 0 */ >> +#define ADV748X_CP_BRI_MAX 127 /* Luma is 508d */ >> + >> +/* Hue Control */ >> +#define ADV748X_CP_HUE 0x3d /* hue_cntrl */ >> +#define ADV748X_CP_HUE_MIN 0 /* -90 degree */ >> +#define ADV748X_CP_HUE_DEF 0 /* -90 degree */ >> +#define ADV748X_CP_HUE_MAX 255 /* +90 degree */ >> + >> +#define ADV748X_CP_VID_ADJ 0x3e /* vid_adj_0 */ >> +#define ADV748X_CP_VID_ADJ_ENABLE BIT(7) /* Enable colour controls */ >> + >> +#define ADV748X_CP_DE_POS_HIGH 0x8b /* de_pos_adj_6 */ >> +#define ADV748X_CP_DE_POS_HIGH_SET BIT(6) >> +#define ADV748X_CP_DE_POS_END_LOW 0x8c /* de_pos_adj_7 */ >> +#define ADV748X_CP_DE_POS_START_LOW 0x8d /* de_pos_adj_8 */ >> + >> +#define ADV748X_CP_VID_ADJ_2 0x91 >> +#define ADV748X_CP_VID_ADJ_2_INTERLACED BIT(6) >> +#define ADV748X_CP_VID_ADJ_2_INTERLACED_3D BIT(4) >> + >> +#define ADV748X_CP_CLMP_POS 0xc9 /* clmp_pos_cntrl_4 */ >> +#define ADV748X_CP_CLMP_POS_DIS_AUTO BIT(0) /* dis_auto_param_buff */ >> + >> +/* CSI : TXA/TXB Maps */ >> +#define ADV748X_CSI_VC_REF 0x0d /* csi_tx_top_reg_0d */ >> +#define ADV748X_CSI_VC_REF_SHIFT 6 >> + >> +#define ADV748X_CSI_FS_AS_LS 0x1e /* csi_tx_top_reg_1e */ >> +#define ADV748X_CSI_FS_AS_LS_UNKNOWN BIT(6) /* Undocumented bit */ >> + >> +/* Register handling */ >> + >> +int adv748x_read(struct adv748x_state *state, u8 addr, u8 reg); >> +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value); >> +int adv748x_write_block(struct adv748x_state *state, int client_page, >> + unsigned int init_reg, const void *val, >> + size_t val_len); >> + >> +#define io_read(s, r) adv748x_read(s, ADV748X_PAGE_IO, r) >> +#define io_write(s, r, v) adv748x_write(s, ADV748X_PAGE_IO, r, v) >> +#define io_clrset(s, r, m, v) io_write(s, r, (io_read(s, r) & ~m) | v) >> + >> +#define hdmi_read(s, r) adv748x_read(s, ADV748X_PAGE_HDMI, r) >> +#define hdmi_read16(s, r, m) (((hdmi_read(s, r) << 8) | hdmi_read(s, r+1)) & m) >> +#define hdmi_write(s, r, v) adv748x_write(s, ADV748X_PAGE_HDMI, r, v) >> +#define hdmi_clrset(s, r, m, v) hdmi_write(s, r, (hdmi_read(s, r) & ~m) | v) >> + >> +#define sdp_read(s, r) adv748x_read(s, ADV748X_PAGE_SDP, r) >> +#define sdp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_SDP, r, v) >> +#define sdp_clrset(s, r, m, v) sdp_write(s, r, (sdp_read(s, r) & ~m) | v) >> + >> +#define cp_read(s, r) adv748x_read(s, ADV748X_PAGE_CP, r) >> +#define cp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_CP, r, v) >> +#define cp_clrset(s, r, m, v) cp_write(s, r, (cp_read(s, r) & ~m) | v) >> + >> +#define txa_read(s, r) adv748x_read(s, ADV748X_PAGE_TXA, r) >> +#define txa_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXA, r, v) >> +#define txa_clrset(s, r, m, v) txa_write(s, r, (txa_read(s, r) & ~m) | v) >> + >> +#define txb_read(s, r) adv748x_read(s, ADV748X_PAGE_TXB, r) >> +#define txb_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXB, r, v) >> +#define txb_clrset(s, r, m, v) txb_write(s, r, (txb_read(s, r) & ~m) | v) >> + >> +#define tx_read(t, r) adv748x_read(t->state, t->page, r) >> +#define tx_write(t, r, v) adv748x_write(t->state, t->page, r, v) >> +#define tx_clrset(t, r, m, v) tx_write(t, r, (tx_read(t, r) & ~m) | v) >> + >> +static inline struct v4l2_subdev *adv748x_get_remote_sd(struct media_pad *pad) >> +{ >> + pad = media_entity_remote_pad(pad); >> + if (!pad) >> + return NULL; >> + >> + return media_entity_to_v4l2_subdev(pad->entity); >> +} >> + >> +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, >> + const struct v4l2_subdev_ops *ops, u32 function, >> + const char *ident); >> + >> +int adv748x_register_subdevs(struct adv748x_state *state, >> + struct v4l2_device *v4l2_dev); >> + >> +int adv748x_txa_power(struct adv748x_state *state, bool on); >> +int adv748x_txb_power(struct adv748x_state *state, bool on); >> + >> +int adv748x_afe_init(struct adv748x_afe *afe); >> +void adv748x_afe_cleanup(struct adv748x_afe *afe); >> + >> +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx); >> +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx); >> +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate); >> + >> +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi); >> +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi); >> + >> +#endif /* _ADV748X_H_ */ >> > > Regards, > > Hans
On 26/06/17 17:14, Kieran Bingham wrote: > Hi Hans, > > Thankyou for your review, and apologies for the delay - I was OoO last week. > > > On 19/06/17 10:13, Hans Verkuil wrote: >> On 06/13/2017 02:35 AM, Kieran Bingham wrote: >>> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >>> >>> Provide support for the ADV7481 and ADV7482. >>> >>> The driver is modelled with 4 subdevices to allow simultaneous streaming >>> from the AFE (Analog front end) and HDMI inputs though two CSI TX >>> entities. >>> >>> The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked >>> to the TXB CSI bus. >>> >>> The driver is based on a prototype by Koji Matsuoka in the Renesas BSP, >>> and an earlier rework by Niklas Söderlund. >>> >>> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >>> >>> --- >>> >>> v2: >>> - Implement DT parsing >>> - adv748x: Add CSI2 entity >>> - adv748x: Rework pad allocations and fmts >>> - Give AFE 8 input pads and move pad defines >>> - Use the enums to ensure pads are referenced correctly. >>> - adv748x: Rename AFE/HDMI entities >>> Now they are 'just afe' and 'just hdmi' >>> - Reorder the entity enum and structures >>> - Added pad-format for the CSI2 entities >>> - CSI2 s_stream pass through >>> - CSI2 control pass through (with link following) >>> >>> v3: >>> - dt: Extend DT documentation to specify interrupt mappings >>> - simplify adv748x_parse_dt >>> - core: Add banner to header file describing ADV748x variants >>> - Use entity structure pointers rather than global state pointers where >>> possible >>> - afe: Reduce indent on afe_status >>> - hdmi: Add error checking to the bt->pixelclock values. >>> - Remove all unnecessary pad checks: handled by core >>> - Fix all probe cleanup paths >>> - adv748x_csi2_probe() now fails if it has no endpoint >>> - csi2: Fix small oneliners for is_txa and get_remote_sd() >>> - csi2: Fix checkpatch warnings >>> - csi2: Fix up s_stream pass-through >>> - csi2: Fix up Pixel Rate passthrough >>> - csi2: simplify adv748x_csi2_get_pad_format() >>> - Remove 'async notifiers' from AFE/HDMI >>> Using async notifiers was overkill, when we have access to the >>> subdevices internally and can register them directly. >>> - Use state lock in control handlers and clean up s_ctrls >>> - remove _interruptible mutex locks >>> >>> v4: >>> - all: Convert hex 0xXX to lowercase >>> - all: Use defines instead of hardcoded register values >>> - all: Use regmap >>> - afe, csi2, hdmi: _probe -> _init >>> - afe, csi2, hdmi: _remove -> _cleanup >>> - afe, hdmi: Convert pattern generator to a control >>> - afe, hdmi: get/set-fmt refactor >>> - afe, hdmi, csi2: Convert to internal calls for pixelrate >>> - afe: Allow the AFE to configure the Input Select from DT >>> - afe: Reduce indent on adv748x_afe_status switch >>> - afe: Remove ununsed macro definitions AIN0-7 >>> - afe: Remove extraneous control checks handled by core >>> - afe: Comment fixups >>> - afe: Rename error label >>> - afe: Correct control names on the SDP >>> - afe: Use AIN0-7 rather than AIN1-8 to match ports and MC pads >>> - core: adv748x_parse_dt references to nodes, and catch multiple >>> endpoints in a port. >>> - core: adv748x_dt_cleanup to simplify releasing DT nodes >>> - core: adv748x_print_info renamed to adv748x_identify_chip >>> - core: reorganise ordering of probe sequence >>> - core: No need for of_match_ptr >>> - core: Fix up i2c read/writes (regmap still on todo list) >>> - core: Set specific functions from the entities on subdev-init >>> - core: Use kzalloc for state instead of devm >>> - core: Improve probe error reporting >>> - core: Track unknown BIT(6) in tx{a,b}_power >>> - csi2: Improve adv748x_csi2_get_remote_sd as adv748x_csi2_get_source_sd >>> - csi2: -EPIPE instead of -ENODEV >>> - csi2: adv_dbg, instead of adv_info >>> - csi2: adv748x_csi2_set_format fix >>> - csi2: remove async notifier and sd member variables >>> - csi2: register links from the CSI2 >>> - csi2: create virtual channel helper function >>> - dt: Remove numbering from endpoints >>> - dt: describe ports and interrupts as optional >>> - dt: Re-tab >>> - hdmi: adv748x_hdmi_have_signal -> adv748x_hdmi_has_signal >>> - hdmi: fix adv748x_hdmi_read_pixelclock return checks >>> - hdmi: improve adv748x_hdmi_set_video_timings >>> - hdmi: Fix tmp variable as polarity >>> - hdmi: Improve adv748x_hdmi_s_stream >>> - hdmi: Clean up adv748x_hdmi_s_ctrl register definitions and usage >>> - hdmi: Fix up adv748x_hdmi_s_dv_timings with macro names for register >>> - hdmi: Add locking to adv748x_hdmi_g_dv_timings >>> writes and locking >>> - hdmi: adv748x_hdmi_set_de_timings function added to clarify DE writes >>> - hdmi: Use CP in control register naming to match component processor >>> - hdmi: clean up adv748x_hdmi_query_dv_timings() >>> - KConfig: Fix up dependency and capitalisation >>> >>> >>> Documentation/devicetree/bindings/media/i2c/adv748x.txt | 96 +- >> >> This should be a separate patch cross posted to the devicetree mailinglist. >> >>> MAINTAINERS | 6 +- >> >> This should also be a separate patch. >> >>> drivers/media/i2c/Kconfig | 11 +- >>> drivers/media/i2c/Makefile | 1 +- >>> drivers/media/i2c/adv748x/Makefile | 7 +- >>> drivers/media/i2c/adv748x/adv748x-afe.c | 571 ++++++- >>> drivers/media/i2c/adv748x/adv748x-core.c | 907 +++++++++- >>> drivers/media/i2c/adv748x/adv748x-csi2.c | 323 +++- >>> drivers/media/i2c/adv748x/adv748x-hdmi.c | 652 ++++++- >>> drivers/media/i2c/adv748x/adv748x.h | 415 ++++- >>> 10 files changed, 2989 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/media/i2c/adv748x.txt >>> create mode 100644 drivers/media/i2c/adv748x/Makefile >>> create mode 100644 drivers/media/i2c/adv748x/adv748x-afe.c >>> create mode 100644 drivers/media/i2c/adv748x/adv748x-core.c >>> create mode 100644 drivers/media/i2c/adv748x/adv748x-csi2.c >>> create mode 100644 drivers/media/i2c/adv748x/adv748x-hdmi.c >>> create mode 100644 drivers/media/i2c/adv748x/adv748x.h >>> >>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt >>> b/Documentation/devicetree/bindings/media/i2c/adv748x.txt >>> new file mode 100644 >>> index 000000000000..b17f8983c992 <snip> >>> +static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std) >>> +{ >>> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >>> + struct adv748x_state *state = adv748x_afe_to_state(afe); >>> + int ret; >>> + >>> + mutex_lock(&state->mutex); >>> + >>> + ret = adv748x_afe_set_video_standard(state, std); >>> + if (ret == 0) >>> + afe->curr_norm = std; >> >> OK, so this is a bit of a problem: you are using V4L2_STD_ALL as an autodetect >> mechanism, but that is not allowed by the V4L2 specification. Yes, some old >> drivers do this and we don't dare to change that, but new drivers should not >> attempt this. The standard set and reported by s_std and g_std must always >> be precise, i.e. no mix of NTSC and PAL. >> >> Only QUERYSTD is allowed to detect the format. > > So how about using V4L2_STD_UNKNOWN as the hint to autodetect and initialising > to NTSC as you suggest in probe. No, don't do that. The current standard must always be a valid non-0 standard. Ditto for dv_timings for that matter. If it doesn't match with the actual detected signal then ENUM_INPUT will set the corresponding error flag in struct v4l2_input. All applications assume that g_std and g_dv_timings return valid values and they rely on QUERYSTD and QUERY_DV_TIMINGS to obtain the detected std/timings. > g_std will then always return either the initial value, a detected value, or > unknown if no lock is available. > > Although then, I'd almost prefer to initialise to V4L2_STD_UNKNOWN ... > >> >> So >> >>> + >>> + mutex_unlock(&state->mutex); >>> + >>> + return ret; >>> +} >>> + >>> +static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) >>> +{ >>> + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); >>> + struct adv748x_state *state = adv748x_afe_to_state(afe); >>> + int ret; >>> + >>> + mutex_lock(&state->mutex); >>> + >>> + if (afe->streaming) { >>> + ret = -EBUSY; >>> + goto unlock; >>> + } >>> + >>> + /* Set auto detect mode */ >>> + ret = adv748x_afe_set_video_standard(state, V4L2_STD_ALL); > > I.e. - I'll set V4L2_STD_UNKNOWN here ... No, don't. It's not the way it works. > >>> + if (ret) >>> + goto unlock; >>> + >>> + msleep(100); >>> + >>> + /* Read detected standard */ >>> + ret = adv748x_afe_status(afe, NULL, std); >>> +unlock: >>> + mutex_unlock(&state->mutex); >>> + >>> + return ret; >>> +} <snip> >>> +int adv748x_afe_init(struct adv748x_afe *afe) >>> +{ >>> + struct adv748x_state *state = adv748x_afe_to_state(afe); >>> + int ret; >>> + unsigned int i; >>> + >>> + afe->input = 0; >>> + afe->streaming = false; >>> + afe->curr_norm = V4L2_STD_ALL; >> >> No. This must be a valid standard. Typically V4L2_STD_NTSC_M. > > Wouldn't V4L2_STD_UNKNOWN be more reasonable at this stage? No, you have to initialize this with a valid standard, and traditionally this is NTSC_M. This also implies that the initial format is 720x480 to correspond with this standard. <snip> >>> + if (on) >>> + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); >>> + else >> >> 'else' isn't needed. > > That's a shame - I think the code is more elegant (/symmetrical) this way - but > no worries. > Adapted. (same for the others) I hate this extra else because it implies that there is a way that the 'if' part can bypass the return and continue after the else. It's obvious in this case that that can't happen, but in more complex code this isn't clear at all. <snip> >>> +static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = { >>> + .type = V4L2_DV_BT_656_1120, >>> + /* keep this initialization for compatibility with GCC < 4.4.6 */ >>> + .reserved = { 0 }, >>> + /* Min pixelclock value is unknown */ >>> + V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH, >>> + ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT, >>> + ADV748X_HDMI_MIN_PIXELCLOCK, >>> + ADV748X_HDMI_MAX_PIXELCLOCK, >>> + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT, >>> + V4L2_DV_BT_CAP_INTERLACED | >> >> Has interlaced been tested? > > No ... > /me ponders if the kit I have can be easily configured to test this. > > Is it better to remove the cap until tested ? Yes. Interlaced is tricky, so in general it should only be enabled if you have actually tested it. The chances of doing this right without testing are pretty slim in my experience. <snip> >>> + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, >>> + V4L2_CID_HUE, ADV748X_CP_HUE_MIN, >>> + ADV748X_CP_HUE_MAX, 1, ADV748X_CP_HUE_DEF); >> >> You should implement the V4L2_CID_DV_RX_POWER_PRESENT control as well, >> once interrupts are working. >> >> Perhaps add a comment as a reminder? > > I have a separate patch where I've started looking at interrupts, but I've put a > comment in here too. > > Is this just to provide connection hotplug events to userspace? Not a hotplug event, it's a receiver, so it sets the hotplug itself. This tests for the 5V pin to become high when a source is connected. Sort of the inverse of the hotplug pin. And yes, userspace wants/needs to know this. Regards, Hans
[snip] On Monday 26 Jun 2017 16:14:47 Kieran Bingham wrote: > >> +int adv748x_txa_power(struct adv748x_state *state, bool on) > >> +{ > >> + int val; > >> + > >> + val = txa_read(state, ADV748X_CSI_FS_AS_LS); > >> + if (val < 0) > >> + return val; > >> + > >> + /* > >> + * This test against BIT(6) is not documented by the datasheet, but > >> was + * specified in the downstream driver. > >> + * Track with a WARN_ONCE to determine if it is ever set by HW. > >> + */ > >> + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), > >> + "Enabling with unknown bit set"); > >> + > >> + if (on) > >> + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); > >> + else > > > > 'else' isn't needed. > > That's a shame - I think the code is more elegant (/symmetrical) this way - > but no worries. > Adapted. (same for the others) For what it's worth, I would personally have kept the else here. I'm all for if (simple_case) { handle_simple_case(); return 0; } /* Complex case */ or similar constructs with s/simple_case/uncommon_case/ or s/simple_case/error_case/, but here the two branches are small and symmetric, so an else makes sense to me to highlight that symmetry. > >> + return adv748x_write_regs(state, adv748x_power_down_txa_4lane); > >> +}
diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt new file mode 100644 index 000000000000..b17f8983c992 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -0,0 +1,96 @@ +* Analog Devices ADV748X video decoder with HDMI receiver + +The ADV7481, and ADV7482 are multi format video decoders with an integrated +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB +from three input sources HDMI, analog and TTL. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7481" for the ADV7481 + - "adi,adv7482" for the ADV7482 + + - reg: I2C slave address + +Optional Properties: + + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or + "intrq3". All interrupts are optional. The "intrq3" interrupt + is only available on the adv7481 + - interrupts: Specify the interrupt lines for the ADV748x + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Name Type Port + --------------------------------------- + AIN0 sink 0 + AIN1 sink 1 + AIN2 sink 2 + AIN3 sink 3 + AIN4 sink 4 + AIN5 sink 5 + AIN6 sink 6 + AIN7 sink 7 + HDMI sink 8 + TTL sink 9 + TXA source 10 + TXB source 11 + +The digital output port nodes must contain at least one endpoint. + +Ports are optional if they are not connected to anything at the hardware level, +but the driver may not provide any support for ports which are not described. + +Example: + + video_receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70>; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gpio6>; + interrupt-names = "intrq1", "intrq2"; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@10 { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@11 { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index eaaa35419fa2..7e2b65240a6f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -776,6 +776,12 @@ L: linux-media@vger.kernel.org S: Maintained F: drivers/media/i2c/adv7511* +ANALOG DEVICES INC ADV748X DRIVER +M: Kieran Bingham <kieran.bingham@ideasonboard.com> +L: linux-media@vger.kernel.org +S: Maintained +F: drivers/media/i2c/adv748x/* + ANALOG DEVICES INC ADV7604 DRIVER M: Hans Verkuil <hans.verkuil@cisco.com> L: linux-media@vger.kernel.org diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index 7c23b7a1fd05..fcbec4273fef 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -204,6 +204,17 @@ config VIDEO_ADV7183 To compile this driver as a module, choose M here: the module will be called adv7183. +config VIDEO_ADV748X + tristate "Analog Devices ADV748x decoder" + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API + depends on OF + ---help--- + V4L2 subdevice driver for the Analog Devices + ADV7481 and ADV7482 HDMI/Analog video decoders. + + To compile this driver as a module, choose M here: the + module will be called adv748x. + config VIDEO_ADV7604 tristate "Analog Devices ADV7604 decoder" depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index 62323ec66be8..e0e6045a2ec8 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o obj-$(CONFIG_VIDEO_ADV7183) += adv7183.o obj-$(CONFIG_VIDEO_ADV7343) += adv7343.o obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o +obj-$(CONFIG_VIDEO_ADV748X) += adv748x/ obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o diff --git a/drivers/media/i2c/adv748x/Makefile b/drivers/media/i2c/adv748x/Makefile new file mode 100644 index 000000000000..c0711e076f1d --- /dev/null +++ b/drivers/media/i2c/adv748x/Makefile @@ -0,0 +1,7 @@ +adv748x-objs := \ + adv748x-afe.o \ + adv748x-core.o \ + adv748x-csi2.o \ + adv748x-hdmi.o + +obj-$(CONFIG_VIDEO_ADV748X) += adv748x.o diff --git a/drivers/media/i2c/adv748x/adv748x-afe.c b/drivers/media/i2c/adv748x/adv748x-afe.c new file mode 100644 index 000000000000..28e95b292d9b --- /dev/null +++ b/drivers/media/i2c/adv748x/adv748x-afe.c @@ -0,0 +1,571 @@ +/* + * Driver for Analog Devices ADV748X 8 channel analog front end (AFE) receiver + * with standard definition processor (SDP) + * + * Copyright (C) 2017 Renesas Electronics Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/v4l2-dv-timings.h> + +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-dv-timings.h> +#include <media/v4l2-ioctl.h> + +#include "adv748x.h" + +/* ----------------------------------------------------------------------------- + * SDP + */ + +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM 0x0 +#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1 +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_J_SECAM 0x2 +#define ADV748X_AFE_STD_AD_PAL_N_NTSC_M_SECAM 0x3 +#define ADV748X_AFE_STD_NTSC_J 0x4 +#define ADV748X_AFE_STD_NTSC_M 0x5 +#define ADV748X_AFE_STD_PAL60 0x6 +#define ADV748X_AFE_STD_NTSC_443 0x7 +#define ADV748X_AFE_STD_PAL_BG 0x8 +#define ADV748X_AFE_STD_PAL_N 0x9 +#define ADV748X_AFE_STD_PAL_M 0xa +#define ADV748X_AFE_STD_PAL_M_PED 0xb +#define ADV748X_AFE_STD_PAL_COMB_N 0xc +#define ADV748X_AFE_STD_PAL_COMB_N_PED 0xd +#define ADV748X_AFE_STD_PAL_SECAM 0xe +#define ADV748X_AFE_STD_PAL_SECAM_PED 0xf + +static int adv748x_afe_read_ro_map(struct adv748x_state *state, u8 reg) +{ + int ret; + + /* Select SDP Read-Only Main Map */ + ret = sdp_write(state, ADV748X_SDP_MAP_SEL, + ADV748X_SDP_MAP_SEL_RO_MAIN); + if (ret < 0) + return ret; + + return sdp_read(state, reg); +} + +static int adv748x_afe_status(struct adv748x_afe *afe, u32 *signal, + v4l2_std_id *std) +{ + struct adv748x_state *state = adv748x_afe_to_state(afe); + int info; + + /* Read status from reg 0x10 of SDP RO Map */ + info = adv748x_afe_read_ro_map(state, ADV748X_SDP_RO_10); + if (info < 0) + return info; + + if (signal) + *signal = info & ADV748X_SDP_RO_10_IN_LOCK ? + 0 : V4L2_IN_ST_NO_SIGNAL; + + if (!std) + return 0; + + /* Standard not valid if there is no signal */ + if (info & BIT(0)) { + *std = V4L2_STD_UNKNOWN; + return 0; + } + + switch (info & 0x70) { + case 0x00: + *std = V4L2_STD_NTSC; + break; + case 0x10: + *std = V4L2_STD_NTSC_443; + break; + case 0x20: + *std = V4L2_STD_PAL_M; + break; + case 0x30: + *std = V4L2_STD_PAL_60; + break; + case 0x40: + *std = V4L2_STD_PAL; + break; + case 0x50: + *std = V4L2_STD_SECAM; + break; + case 0x60: + *std = V4L2_STD_PAL_Nc | V4L2_STD_PAL_N; + break; + case 0x70: + *std = V4L2_STD_SECAM; + break; + default: + *std = V4L2_STD_UNKNOWN; + break; + } + + return 0; +} + +static void adv748x_afe_fill_format(struct adv748x_afe *afe, + struct v4l2_mbus_framefmt *fmt) +{ + v4l2_std_id std; + + memset(fmt, 0, sizeof(*fmt)); + + fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; + fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; + fmt->field = V4L2_FIELD_INTERLACED; + + fmt->width = 720; + + if (afe->curr_norm == V4L2_STD_ALL) + adv748x_afe_status(afe, NULL, &std); + else + std = afe->curr_norm; + + fmt->height = std & V4L2_STD_525_60 ? 480 : 576; +} + +static int adv748x_afe_std(v4l2_std_id std) +{ + if (std == V4L2_STD_ALL) + return ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM; + if (std == V4L2_STD_PAL_60) + return ADV748X_AFE_STD_PAL60; + if (std == V4L2_STD_NTSC_443) + return ADV748X_AFE_STD_NTSC_443; + if (std == V4L2_STD_PAL_N) + return ADV748X_AFE_STD_PAL_N; + if (std == V4L2_STD_PAL_M) + return ADV748X_AFE_STD_PAL_M; + if (std == V4L2_STD_PAL_Nc) + return ADV748X_AFE_STD_PAL_COMB_N; + if (std & V4L2_STD_PAL) + return ADV748X_AFE_STD_PAL_BG; + if (std & V4L2_STD_NTSC) + return ADV748X_AFE_STD_NTSC_M; + if (std & V4L2_STD_SECAM) + return ADV748X_AFE_STD_PAL_SECAM; + + return -EINVAL; +} + +static int adv748x_afe_set_video_standard(struct adv748x_state *state, + v4l2_std_id std) +{ + int sdpstd; + + sdpstd = adv748x_afe_std(std); + if (sdpstd < 0) + return sdpstd; + + sdp_clrset(state, ADV748X_SDP_VID_SEL, ADV748X_SDP_VID_SEL_MASK, + (sdpstd & 0xf) << ADV748X_SDP_VID_SEL_SHIFT); + + return 0; +} + +static int adv748x_afe_s_input(struct adv748x_afe *afe, unsigned int input) +{ + struct adv748x_state *state = adv748x_afe_to_state(afe); + + return sdp_write(state, ADV748X_SDP_INSEL, input); +} + +static int adv748x_afe_g_pixelaspect(struct v4l2_subdev *sd, + struct v4l2_fract *aspect) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + v4l2_std_id std; + + if (afe->curr_norm == V4L2_STD_ALL) + adv748x_afe_status(afe, NULL, &std); + else + std = afe->curr_norm; + + if (std & V4L2_STD_525_60) { + aspect->numerator = 11; + aspect->denominator = 10; + } else { + aspect->numerator = 54; + aspect->denominator = 59; + } + + return 0; +} + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_video_ops + */ + +static int adv748x_afe_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + + if (afe->curr_norm == V4L2_STD_ALL) + adv748x_afe_status(afe, NULL, norm); + else + *norm = afe->curr_norm; + + return 0; +} + +static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + struct adv748x_state *state = adv748x_afe_to_state(afe); + int ret; + + mutex_lock(&state->mutex); + + ret = adv748x_afe_set_video_standard(state, std); + if (ret == 0) + afe->curr_norm = std; + + mutex_unlock(&state->mutex); + + return ret; +} + +static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + struct adv748x_state *state = adv748x_afe_to_state(afe); + int ret; + + mutex_lock(&state->mutex); + + if (afe->streaming) { + ret = -EBUSY; + goto unlock; + } + + /* Set auto detect mode */ + ret = adv748x_afe_set_video_standard(state, V4L2_STD_ALL); + if (ret) + goto unlock; + + msleep(100); + + /* Read detected standard */ + ret = adv748x_afe_status(afe, NULL, std); +unlock: + mutex_unlock(&state->mutex); + + return ret; +} + +static int adv748x_afe_g_tvnorms(struct v4l2_subdev *sd, v4l2_std_id *norm) +{ + *norm = V4L2_STD_ALL; + + return 0; +} + +static int adv748x_afe_g_input_status(struct v4l2_subdev *sd, u32 *status) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + struct adv748x_state *state = adv748x_afe_to_state(afe); + int ret; + + mutex_lock(&state->mutex); + + ret = adv748x_afe_status(afe, status, NULL); + + mutex_unlock(&state->mutex); + return ret; +} + +static int adv748x_afe_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + struct adv748x_state *state = adv748x_afe_to_state(afe); + int ret, signal = V4L2_IN_ST_NO_SIGNAL; + + mutex_lock(&state->mutex); + + if (enable) { + ret = adv748x_afe_s_input(afe, afe->input); + if (ret) + goto unlock; + } + + ret = adv748x_txb_power(state, enable); + if (ret) + goto unlock; + + afe->streaming = enable; + + adv748x_afe_status(afe, &signal, NULL); + if (signal != V4L2_IN_ST_NO_SIGNAL) + adv_dbg(state, "Detected SDP signal\n"); + else + adv_dbg(state, "Couldn't detect SDP video signal\n"); + +unlock: + mutex_unlock(&state->mutex); + + return ret; +} + +static const struct v4l2_subdev_video_ops adv748x_afe_video_ops = { + .g_std = adv748x_afe_g_std, + .s_std = adv748x_afe_s_std, + .querystd = adv748x_afe_querystd, + .g_tvnorms = adv748x_afe_g_tvnorms, + .g_input_status = adv748x_afe_g_input_status, + .s_stream = adv748x_afe_s_stream, + .g_pixelaspect = adv748x_afe_g_pixelaspect, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_pad_ops + */ + +static int adv748x_afe_set_pixelrate(struct adv748x_afe *afe) +{ + struct v4l2_subdev *tx; + unsigned int width, height, fps; + + tx = adv748x_get_remote_sd(&afe->pads[ADV748X_AFE_SOURCE]); + if (!tx) + return -ENOLINK; + + width = 720; + height = afe->curr_norm & V4L2_STD_525_60 ? 480 : 576; + fps = afe->curr_norm & V4L2_STD_525_60 ? 30 : 25; + + return adv748x_csi2_set_pixelrate(tx, width * height * fps); +} + +static int adv748x_afe_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->index != 0) + return -EINVAL; + + code->code = MEDIA_BUS_FMT_UYVY8_2X8; + + return 0; +} + +static int adv748x_afe_get_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct adv748x_afe *afe = adv748x_sd_to_afe(sd); + struct v4l2_mbus_framefmt *mbusformat; + + /* The format of the analog sink pads is nonsensical */ + if (sdformat->pad != ADV748X_AFE_SOURCE) + return -EINVAL; + + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); + sdformat->format = *mbusformat; + } else { + adv748x_afe_fill_format(afe, &sdformat->format); + adv748x_afe_set_pixelrate(afe); + } + + return 0; +} + +static int adv748x_afe_set_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct v4l2_mbus_framefmt *mbusformat; + + /* The format of the analog sink pads is nonsensical */ + if (sdformat->pad != ADV748X_AFE_SOURCE) + return -EINVAL; + + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) + return adv748x_afe_get_format(sd, cfg, sdformat); + + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); + *mbusformat = sdformat->format; + + return 0; +} + +static const struct v4l2_subdev_pad_ops adv748x_afe_pad_ops = { + .enum_mbus_code = adv748x_afe_enum_mbus_code, + .set_fmt = adv748x_afe_set_format, + .get_fmt = adv748x_afe_get_format, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_ops + */ + +static const struct v4l2_subdev_ops adv748x_afe_ops = { + .video = &adv748x_afe_video_ops, + .pad = &adv748x_afe_pad_ops, +}; + +/* ----------------------------------------------------------------------------- + * Controls + */ + +static const char * const afe_ctrl_frp_menu[] = { + "Disabled", + "Default Value", + "Color Bars", + "Grey Ramp", + "Cb Ramp", + "Cr Ramp", + "Boundary" +}; + +static int adv748x_afe_s_ctrl(struct v4l2_ctrl *ctrl) +{ + struct adv748x_afe *afe = adv748x_ctrl_to_afe(ctrl); + struct adv748x_state *state = adv748x_afe_to_state(afe); + bool enable; + int ret; + + ret = sdp_write(state, 0x0e, 0x00); + if (ret < 0) + return ret; + + switch (ctrl->id) { + case V4L2_CID_BRIGHTNESS: + ret = sdp_write(state, ADV748X_SDP_BRI, ctrl->val); + break; + case V4L2_CID_HUE: + /* Hue is inverted according to HSL chart */ + ret = sdp_write(state, ADV748X_SDP_HUE, -ctrl->val); + break; + case V4L2_CID_CONTRAST: + ret = sdp_write(state, ADV748X_SDP_CON, ctrl->val); + break; + case V4L2_CID_SATURATION: + ret = sdp_write(state, ADV748X_SDP_SD_SAT_U, ctrl->val); + if (ret) + break; + ret = sdp_write(state, ADV748X_SDP_SD_SAT_V, ctrl->val); + break; + case V4L2_CID_TEST_PATTERN: + enable = !!ctrl->val; + + /* Enable/Disable Color bar test patterns */ + ret = sdp_clrset(state, ADV748X_SDP_DEF, ADV748X_SDP_DEF_VAL_EN, + enable); + if (ret) + break; + ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, + enable ? ctrl->val - 1 : 0); + break; + default: + return -EINVAL; + } + + return ret; +} + +static const struct v4l2_ctrl_ops adv748x_afe_ctrl_ops = { + .s_ctrl = adv748x_afe_s_ctrl, +}; + +static int adv748x_afe_init_controls(struct adv748x_afe *afe) +{ + struct adv748x_state *state = adv748x_afe_to_state(afe); + + v4l2_ctrl_handler_init(&afe->ctrl_hdl, 5); + + /* Use our mutex for the controls */ + afe->ctrl_hdl.lock = &state->mutex; + + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, + V4L2_CID_BRIGHTNESS, ADV748X_SDP_BRI_MIN, + ADV748X_SDP_BRI_MAX, 1, ADV748X_SDP_BRI_DEF); + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, + V4L2_CID_CONTRAST, ADV748X_SDP_CON_MIN, + ADV748X_SDP_CON_MAX, 1, ADV748X_SDP_CON_DEF); + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, + V4L2_CID_SATURATION, ADV748X_SDP_SAT_MIN, + ADV748X_SDP_SAT_MAX, 1, ADV748X_SDP_SAT_DEF); + v4l2_ctrl_new_std(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, + V4L2_CID_HUE, ADV748X_SDP_HUE_MIN, + ADV748X_SDP_HUE_MAX, 1, ADV748X_SDP_HUE_DEF); + + v4l2_ctrl_new_std_menu_items(&afe->ctrl_hdl, &adv748x_afe_ctrl_ops, + V4L2_CID_TEST_PATTERN, + ARRAY_SIZE(afe_ctrl_frp_menu) - 1, + 0, 0, afe_ctrl_frp_menu); + + afe->sd.ctrl_handler = &afe->ctrl_hdl; + if (afe->ctrl_hdl.error) { + v4l2_ctrl_handler_free(&afe->ctrl_hdl); + return afe->ctrl_hdl.error; + } + + return v4l2_ctrl_handler_setup(&afe->ctrl_hdl); +} + +int adv748x_afe_init(struct adv748x_afe *afe) +{ + struct adv748x_state *state = adv748x_afe_to_state(afe); + int ret; + unsigned int i; + + afe->input = 0; + afe->streaming = false; + afe->curr_norm = V4L2_STD_ALL; + + adv748x_subdev_init(&afe->sd, state, &adv748x_afe_ops, + MEDIA_ENT_F_ATV_DECODER, "afe"); + + /* Identify the first connector found as a default input if set */ + for (i = ADV748X_PORT_AIN0; i <= ADV748X_PORT_AIN7; i++) { + /* Inputs and ports are 1-indexed to match the data sheet */ + if (state->endpoints[i]) { + afe->input = i; + break; + } + } + + adv748x_afe_s_input(afe, afe->input); + + adv_dbg(state, "AFE Default input set to %d\n", afe->input); + + /* Entity pads and sinks are 0-indexed to match the pads */ + for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++) + afe->pads[i].flags = MEDIA_PAD_FL_SINK; + + afe->pads[ADV748X_AFE_SOURCE].flags = MEDIA_PAD_FL_SOURCE; + + ret = media_entity_pads_init(&afe->sd.entity, ADV748X_AFE_NR_PADS, + afe->pads); + if (ret) + return ret; + + ret = adv748x_afe_init_controls(afe); + if (ret) + goto error; + + return 0; + +error: + media_entity_cleanup(&afe->sd.entity); + + return ret; +} + +void adv748x_afe_cleanup(struct adv748x_afe *afe) +{ + v4l2_device_unregister_subdev(&afe->sd); + media_entity_cleanup(&afe->sd.entity); + v4l2_ctrl_handler_free(&afe->ctrl_hdl); +} diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c new file mode 100644 index 000000000000..6e395a4524ec --- /dev/null +++ b/drivers/media/i2c/adv748x/adv748x-core.c @@ -0,0 +1,907 @@ +/* + * Driver for Analog Devices ADV748X HDMI receiver with AFE + * + * Copyright (C) 2017 Renesas Electronics Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Authors: + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> + * Niklas Söderlund <niklas.soderlund@ragnatech.se> + * Kieran Bingham <kieran.bingham@ideasonboard.com> + */ + +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/of_graph.h> +#include <linux/regmap.h> +#include <linux/v4l2-dv-timings.h> + +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-dv-timings.h> +#include <media/v4l2-ioctl.h> + +#include "adv748x.h" + +/* ----------------------------------------------------------------------------- + * Register manipulation + */ + +static const struct regmap_config adv748x_regmap_cnf[] = { + { + .name = "io", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "dpll", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "cp", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "hdmi", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "edid", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "repeater", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "infoframe", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "cec", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "sdp", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + + { + .name = "txb", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, + { + .name = "txa", + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_NONE, + }, +}; + +static int adv748x_configure_regmap(struct adv748x_state *state, int region) +{ + int err; + + if (!state->i2c_clients[region]) + return -ENODEV; + + state->regmap[region] = + devm_regmap_init_i2c(state->i2c_clients[region], + &adv748x_regmap_cnf[region]); + + if (IS_ERR(state->regmap[region])) { + err = PTR_ERR(state->regmap[region]); + adv_err(state, + "Error initializing regmap %d with error %d\n", + region, err); + return -EINVAL; + } + + return 0; +} + +/* Default addresses for the I2C pages */ +static int adv748x_i2c_addresses[ADV748X_PAGE_MAX] = { + ADV748X_I2C_IO, + ADV748X_I2C_DPLL, + ADV748X_I2C_CP, + ADV748X_I2C_HDMI, + ADV748X_I2C_EDID, + ADV748X_I2C_REPEATER, + ADV748X_I2C_INFOFRAME, + ADV748X_I2C_CEC, + ADV748X_I2C_SDP, + ADV748X_I2C_TXB, + ADV748X_I2C_TXA, +}; + +static int adv748x_read_check(struct adv748x_state *state, + int client_page, u8 reg) +{ + struct i2c_client *client = state->i2c_clients[client_page]; + int err; + unsigned int val; + + err = regmap_read(state->regmap[client_page], reg, &val); + + if (err) { + adv_err(state, "error reading %02x, %02x\n", + client->addr, reg); + return err; + } + + return val; +} + +int adv748x_read(struct adv748x_state *state, u8 page, u8 reg) +{ + return adv748x_read_check(state, page, reg); +} + +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value) +{ + return regmap_write(state->regmap[page], reg, value); +} + +/* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX + * size to one or more registers. + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ +int adv748x_write_block(struct adv748x_state *state, int client_page, + unsigned int init_reg, const void *val, + size_t val_len) +{ + struct regmap *regmap = state->regmap[client_page]; + + if (val_len > I2C_SMBUS_BLOCK_MAX) + val_len = I2C_SMBUS_BLOCK_MAX; + + return regmap_raw_write(regmap, init_reg, val, val_len); +} + + +static struct i2c_client *adv748x_dummy_client(struct adv748x_state *state, + u8 addr, u8 io_reg) +{ + struct i2c_client *client = state->client; + + if (addr) + io_write(state, io_reg, addr << 1); + + return i2c_new_dummy(client->adapter, io_read(state, io_reg) >> 1); +} + +static void adv748x_unregister_clients(struct adv748x_state *state) +{ + unsigned int i; + + for (i = 1; i < ARRAY_SIZE(state->i2c_clients); ++i) { + if (state->i2c_clients[i]) + i2c_unregister_device(state->i2c_clients[i]); + } +} + +static int adv748x_initialise_clients(struct adv748x_state *state) +{ + int i; + int ret; + + for (i = ADV748X_PAGE_DPLL; i < ADV748X_PAGE_MAX; ++i) { + state->i2c_clients[i] = + adv748x_dummy_client(state, adv748x_i2c_addresses[i], + ADV748X_IO_SLAVE_ADDR_BASE + i); + if (state->i2c_clients[i] == NULL) { + adv_err(state, "failed to create i2c client %u\n", i); + return -ENOMEM; + } + + ret = adv748x_configure_regmap(state, i); + if (ret) + return ret; + } + + return 0; +} + +/** + * struct adv748x_reg_value - Register write instruction + * @page: Regmap page identifier + * @reg: I2C register + * @value: value to write to @page at @reg + */ +struct adv748x_reg_value { + u8 page; + u8 reg; + u8 value; +}; + +static int adv748x_write_regs(struct adv748x_state *state, + const struct adv748x_reg_value *regs) +{ + int ret; + + while (regs->page != ADV748X_PAGE_EOR) { + if (regs->page == ADV748X_PAGE_WAIT) { + msleep(regs->value); + } else { + ret = adv748x_write(state, regs->page, regs->reg, + regs->value); + if (ret < 0) { + adv_err(state, + "Error regs page: 0x%02x reg: 0x%02x\n", + regs->page, regs->reg); + return ret; + } + } + regs++; + } + + return 0; +} + + +/* ----------------------------------------------------------------------------- + * TXA and TXB + */ + +static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = { + + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ + + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = { + + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x1e, 0x00}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + {ADV748X_PAGE_TXA, 0xc1, 0x3b}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = { + + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ + + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = { + + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x1e, 0x00}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 4-lane MIPI */ + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + {ADV748X_PAGE_TXB, 0xc1, 0x3b}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +int adv748x_txa_power(struct adv748x_state *state, bool on) +{ + int val; + + val = txa_read(state, ADV748X_CSI_FS_AS_LS); + if (val < 0) + return val; + + /* + * This test against BIT(6) is not documented by the datasheet, but was + * specified in the downstream driver. + * Track with a WARN_ONCE to determine if it is ever set by HW. + */ + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), + "Enabling with unknown bit set"); + + if (on) + return adv748x_write_regs(state, adv748x_power_up_txa_4lane); + else + return adv748x_write_regs(state, adv748x_power_down_txa_4lane); +} + +int adv748x_txb_power(struct adv748x_state *state, bool on) +{ + int val; + + val = txb_read(state, ADV748X_CSI_FS_AS_LS); + if (val < 0) + return val; + + /* + * This test against BIT(6) is not documented by the datasheet, but was + * specified in the downstream driver. + * Track with a WARN_ONCE to determine if it is ever set by HW. + */ + WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN), + "Enabling with unknown bit set"); + + if (on) + return adv748x_write_regs(state, adv748x_power_up_txb_1lane); + else + return adv748x_write_regs(state, adv748x_power_down_txb_1lane); +} + +/* ----------------------------------------------------------------------------- + * Media Operations + */ + +static const struct media_entity_operations adv748x_media_ops = { + .link_validate = v4l2_subdev_link_validate, +}; + +/* ----------------------------------------------------------------------------- + * HW setup + */ + +static const struct adv748x_reg_value adv748x_sw_reset[] = { + + {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */ + {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */ + {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */ + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +static const struct adv748x_reg_value adv748x_set_slave_address[] = { + {ADV748X_PAGE_IO, 0xf3, ADV748X_I2C_DPLL << 1}, + {ADV748X_PAGE_IO, 0xf4, ADV748X_I2C_CP << 1}, + {ADV748X_PAGE_IO, 0xf5, ADV748X_I2C_HDMI << 1}, + {ADV748X_PAGE_IO, 0xf6, ADV748X_I2C_EDID << 1}, + {ADV748X_PAGE_IO, 0xf7, ADV748X_I2C_REPEATER << 1}, + {ADV748X_PAGE_IO, 0xf8, ADV748X_I2C_INFOFRAME << 1}, + {ADV748X_PAGE_IO, 0xfa, ADV748X_I2C_CEC << 1}, + {ADV748X_PAGE_IO, 0xfb, ADV748X_I2C_SDP << 1}, + {ADV748X_PAGE_IO, 0xfc, ADV748X_I2C_TXB << 1}, + {ADV748X_PAGE_IO, 0xfd, ADV748X_I2C_TXA << 1}, + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +/* Supported Formats For Script Below */ +/* - 01-29 HDMI to MIPI TxA CSI 4-Lane - RGB888: */ +static const struct adv748x_reg_value adv748x_init_txa_4lane[] = { + /* Disable chip powerdown & Enable HDMI Rx block */ + {ADV748X_PAGE_IO, 0x00, 0x40}, + + {ADV748X_PAGE_REPEATER, 0x40, 0x83}, /* Enable HDCP 1.1 */ + + {ADV748X_PAGE_HDMI, 0x00, 0x08},/* Foreground Channel = A */ + {ADV748X_PAGE_HDMI, 0x98, 0xff},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x99, 0xa3},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x9a, 0x00},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x9b, 0x0a},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x9d, 0x40},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0xcb, 0x09},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x3d, 0x10},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x3e, 0x7b},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x3f, 0x5e},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x4e, 0xfe},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x4f, 0x18},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x57, 0xa3},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x58, 0x04},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0x85, 0x10},/* ADI Required Write */ + + {ADV748X_PAGE_HDMI, 0x83, 0x00},/* Enable All Terminations */ + {ADV748X_PAGE_HDMI, 0xa3, 0x01},/* ADI Required Write */ + {ADV748X_PAGE_HDMI, 0xbe, 0x00},/* ADI Required Write */ + + {ADV748X_PAGE_HDMI, 0x6c, 0x01},/* HPA Manual Enable */ + {ADV748X_PAGE_HDMI, 0xf8, 0x01},/* HPA Asserted */ + {ADV748X_PAGE_HDMI, 0x0f, 0x00},/* Audio Mute Speed Set to Fastest */ + /* (Smallest Step Size) */ + + {ADV748X_PAGE_IO, 0x04, 0x02}, /* RGB Out of CP */ + {ADV748X_PAGE_IO, 0x12, 0xf0}, /* CSC Depends on ip Packets, SDR 444 */ + {ADV748X_PAGE_IO, 0x17, 0x80}, /* Luma & Chroma can reach 254d */ + {ADV748X_PAGE_IO, 0x03, 0x86}, /* CP-Insert_AV_Code */ + + {ADV748X_PAGE_CP, 0x7c, 0x00}, /* ADI Required Write */ + + {ADV748X_PAGE_IO, 0x0c, 0xe0}, /* Enable LLC_DLL & Double LLC Timing */ + {ADV748X_PAGE_IO, 0x0e, 0xdd}, /* LLC/PIX/SPI PINS TRISTATED AUD */ + /* Outputs Enabled */ + {ADV748X_PAGE_IO, 0x10, 0xa0}, /* Enable 4-lane CSI Tx & Pixel Port */ + + {ADV748X_PAGE_TXA, 0x00, 0x84}, /* Enable 4-lane MIPI */ + {ADV748X_PAGE_TXA, 0x00, 0xa4}, /* Set Auto DPHY Timing */ + {ADV748X_PAGE_TXA, 0xdb, 0x10}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0xd6, 0x07}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0xc4, 0x0a}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x71, 0x33}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x72, 0x11}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ + + {ADV748X_PAGE_TXA, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0x1e, 0x40}, /* ADI Required Write */ + {ADV748X_PAGE_TXA, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ + {ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXA, 0xc1, 0x2b}, /* ADI Required Write */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXA, 0x31, 0x80}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +/* 02-01 Analog CVBS to MIPI TX-B CSI 1-Lane - */ +/* Autodetect CVBS Single Ended In Ain 1 - MIPI Out */ +static const struct adv748x_reg_value adv748x_init_txb_1lane[] = { + + {ADV748X_PAGE_IO, 0x00, 0x30}, /* Disable chip powerdown Rx */ + {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */ + + {ADV748X_PAGE_IO, 0x0e, 0xff}, /* LLC/PIX/AUD/SPI PINS TRISTATED */ + + {ADV748X_PAGE_SDP, 0x0f, 0x00}, /* Exit Power Down Mode */ + {ADV748X_PAGE_SDP, 0x52, 0xcd}, /* ADI Required Write */ + + {ADV748X_PAGE_SDP, 0x0e, 0x80}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0x9c, 0x00}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0x9c, 0xff}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0x0e, 0x00}, /* ADI Required Write */ + + /* ADI recommended writes for improved video quality */ + {ADV748X_PAGE_SDP, 0x80, 0x51}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0x81, 0x51}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0x82, 0x68}, /* ADI Required Write */ + + {ADV748X_PAGE_SDP, 0x03, 0x42}, /* Tri-S Output , PwrDwn 656 pads */ + {ADV748X_PAGE_SDP, 0x04, 0xb5}, /* ITU-R BT.656-4 compatible */ + {ADV748X_PAGE_SDP, 0x13, 0x00}, /* ADI Required Write */ + + {ADV748X_PAGE_SDP, 0x17, 0x41}, /* Select SH1 */ + {ADV748X_PAGE_SDP, 0x31, 0x12}, /* ADI Required Write */ + {ADV748X_PAGE_SDP, 0xe6, 0x4f}, /* V bit end pos manually in NTSC */ + + /* Enable 1-Lane MIPI Tx, */ + /* enable pixel output and route SD through Pixel port */ + {ADV748X_PAGE_IO, 0x10, 0x70}, + + {ADV748X_PAGE_TXB, 0x00, 0x81}, /* Enable 1-lane MIPI */ + {ADV748X_PAGE_TXB, 0x00, 0xa1}, /* Set Auto DPHY Timing */ + {ADV748X_PAGE_TXB, 0xd2, 0x40}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0xc4, 0x0a}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x71, 0x33}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x72, 0x11}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0xf0, 0x00}, /* i2c_dphy_pwdn - 1'b0 */ + {ADV748X_PAGE_TXB, 0x31, 0x82}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0x1e, 0x40}, /* ADI Required Write */ + {ADV748X_PAGE_TXB, 0xda, 0x01}, /* i2c_mipi_pll_en - 1'b1 */ + + {ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */ + {ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXB, 0xc1, 0x2b}, /* ADI Required Write */ + {ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */ + {ADV748X_PAGE_TXB, 0x31, 0x80}, /* ADI Required Write */ + + {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ +}; + +static int adv748x_reset(struct adv748x_state *state) +{ + int ret; + + ret = adv748x_write_regs(state, adv748x_sw_reset); + if (ret < 0) + return ret; + + ret = adv748x_write_regs(state, adv748x_set_slave_address); + if (ret < 0) + return ret; + + /* Init and power down TXA */ + ret = adv748x_write_regs(state, adv748x_init_txa_4lane); + if (ret) + return ret; + + adv748x_txa_power(state, 0); + + /* Init and power down TXB */ + ret = adv748x_write_regs(state, adv748x_init_txb_1lane); + if (ret) + return ret; + + adv748x_txb_power(state, 0); + + /* Disable chip powerdown & Enable HDMI Rx block */ + io_write(state, ADV748X_IO_PD, ADV748X_IO_PD_RX_EN); + + /* Enable 4-lane CSI Tx & Pixel Port */ + io_write(state, ADV748X_IO_10, ADV748X_IO_10_CSI4_EN | + ADV748X_IO_10_CSI1_EN | + ADV748X_IO_10_PIX_OUT_EN); + + /* Use vid_std and v_freq as freerun resolution for CP */ + cp_clrset(state, ADV748X_CP_CLMP_POS, ADV748X_CP_CLMP_POS_DIS_AUTO, + ADV748X_CP_CLMP_POS_DIS_AUTO); + + return 0; +} + +static int adv748x_identify_chip(struct adv748x_state *state) +{ + int msb, lsb; + + lsb = io_read(state, ADV748X_IO_CHIP_REV_ID_1); + msb = io_read(state, ADV748X_IO_CHIP_REV_ID_2); + + if (lsb < 0 || msb < 0) { + adv_err(state, "Failed to read chip revision\n"); + return -EIO; + } + + adv_info(state, "chip found @ 0x%02x revision %02x%02x\n", + state->client->addr << 1, lsb, msb); + + return 0; +} + +/* ----------------------------------------------------------------------------- + * i2c driver + */ + +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, + const struct v4l2_subdev_ops *ops, u32 function, + const char *ident) +{ + v4l2_subdev_init(sd, ops); + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + + /* the owner is the same as the i2c_client's driver owner */ + sd->owner = state->dev->driver->owner; + sd->dev = state->dev; + + v4l2_set_subdevdata(sd, state); + + /* initialize name */ + snprintf(sd->name, sizeof(sd->name), "%s %d-%04x %s", + state->dev->driver->name, + i2c_adapter_id(state->client->adapter), + state->client->addr, ident); + + sd->entity.function = function; + sd->entity.ops = &adv748x_media_ops; +} + +static int adv748x_parse_dt(struct adv748x_state *state) +{ + struct device_node *ep_np = NULL; + struct of_endpoint ep; + bool found = false; + + for_each_endpoint_of_node(state->dev->of_node, ep_np) { + of_graph_parse_endpoint(ep_np, &ep); + adv_info(state, "Endpoint %s on port %d", + of_node_full_name(ep.local_node), + ep.port); + + if (ep.port >= ADV748X_PORT_MAX) { + adv_err(state, "Invalid endpoint %s on port %d", + of_node_full_name(ep.local_node), + ep.port); + + continue; + } + + if (state->endpoints[ep.port]) { + adv_err(state, + "Multiple port endpoints are not supported"); + continue; + } + + of_node_get(ep_np); + state->endpoints[ep.port] = ep_np; + + found = true; + } + + return found ? 0 : -ENODEV; +} + +static void adv748x_dt_cleanup(struct adv748x_state *state) +{ + unsigned int i; + + for (i = 0; i < ADV748X_PORT_MAX; i++) + of_node_put(state->endpoints[i]); +} + +static int adv748x_setup_links(struct adv748x_state *state) +{ + int ret; + int enabled = MEDIA_LNK_FL_ENABLED; + +/* + * HACK/Workaround: + * + * Currently non-immutable link resets go through the RVin + * driver, and cause the links to fail, due to not being part of RVIN. + * As a temporary workaround until the RVIN driver knows better than to parse + * links that do not belong to it, use static immutable links for our internal + * media paths. + */ +#define ADV748x_DEV_STATIC_LINKS +#ifdef ADV748x_DEV_STATIC_LINKS + enabled |= MEDIA_LNK_FL_IMMUTABLE; +#endif + + /* TXA - Default link is with HDMI */ + ret = media_create_pad_link(&state->hdmi.sd.entity, 1, + &state->txa.sd.entity, 0, enabled); + if (ret) { + adv_err(state, "Failed to create HDMI-TXA pad link"); + return ret; + } + +#ifndef ADV748x_DEV_STATIC_LINKS + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, + &state->txa.sd.entity, 0, 0); + if (ret) { + adv_err(state, "Failed to create AFE-TXA pad link"); + return ret; + } +#endif + + /* TXB - Can only output from the AFE */ + ret = media_create_pad_link(&state->afe.sd.entity, ADV748X_AFE_SOURCE, + &state->txb.sd.entity, 0, enabled); + if (ret) { + adv_err(state, "Failed to create AFE-TXB pad link"); + return ret; + } + + return 0; +} + +int adv748x_register_subdevs(struct adv748x_state *state, + struct v4l2_device *v4l2_dev) +{ + int ret; + + ret = v4l2_device_register_subdev(v4l2_dev, &state->hdmi.sd); + if (ret < 0) + return ret; + + ret = v4l2_device_register_subdev(v4l2_dev, &state->afe.sd); + if (ret < 0) + goto err_unregister_hdmi; + + ret = adv748x_setup_links(state); + if (ret < 0) + goto err_unregister_afe; + + return 0; + +err_unregister_afe: + v4l2_device_unregister_subdev(&state->afe.sd); +err_unregister_hdmi: + v4l2_device_unregister_subdev(&state->hdmi.sd); + + return ret; +} + +static int adv748x_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct adv748x_state *state; + int ret; + + /* Check if the adapter supports the needed features */ + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -EIO; + + state = kzalloc(sizeof(struct adv748x_state), GFP_KERNEL); + if (!state) + return -ENOMEM; + + mutex_init(&state->mutex); + + state->dev = &client->dev; + state->client = client; + state->i2c_clients[ADV748X_PAGE_IO] = client; + i2c_set_clientdata(client, state); + + /* Discover and process ports declared by the Device tree endpoints */ + ret = adv748x_parse_dt(state); + if (ret) { + adv_err(state, "Failed to parse device tree"); + goto err_free_mutex; + } + + /* Configure IO Regmap region */ + ret = adv748x_configure_regmap(state, ADV748X_PAGE_IO); + if (ret) { + adv_err(state, "Error configuring IO regmap region"); + goto err_cleanup_dt; + } + + ret = adv748x_identify_chip(state); + if (ret) { + adv_err(state, "Failed to identify chip"); + goto err_cleanup_clients; + } + + /* Configure remaining pages as I2C clients with regmap access */ + ret = adv748x_initialise_clients(state); + if (ret) { + adv_err(state, "Failed to setup client regmap pages"); + goto err_cleanup_clients; + } + + /* SW reset ADV748X to its default values */ + ret = adv748x_reset(state); + if (ret) { + adv_err(state, "Failed to reset hardware"); + goto err_cleanup_clients; + } + + /* Initialise HDMI */ + ret = adv748x_hdmi_init(&state->hdmi); + if (ret) { + adv_err(state, "Failed to probe HDMI"); + goto err_cleanup_clients; + } + + /* Initialise AFE */ + ret = adv748x_afe_init(&state->afe); + if (ret) { + adv_err(state, "Failed to probe AFE"); + goto err_cleanup_hdmi; + } + + /* Initialise TXA */ + ret = adv748x_csi2_init(state, &state->txa); + if (ret) { + adv_err(state, "Failed to probe TXA"); + goto err_cleanup_afe; + } + + /* Initialise TXB */ + ret = adv748x_csi2_init(state, &state->txb); + if (ret) { + adv_err(state, "Failed to probe TXB"); + goto err_cleanup_txa; + } + + return 0; + +err_cleanup_txa: + adv748x_csi2_cleanup(&state->txa); +err_cleanup_afe: + adv748x_afe_cleanup(&state->afe); +err_cleanup_hdmi: + adv748x_hdmi_cleanup(&state->hdmi); +err_cleanup_clients: + adv748x_unregister_clients(state); +err_cleanup_dt: + adv748x_dt_cleanup(state); +err_free_mutex: + mutex_destroy(&state->mutex); + kfree(state); + + return ret; +} + +static int adv748x_remove(struct i2c_client *client) +{ + struct adv748x_state *state = i2c_get_clientdata(client); + + adv748x_afe_cleanup(&state->afe); + adv748x_hdmi_cleanup(&state->hdmi); + + adv748x_csi2_cleanup(&state->txa); + adv748x_csi2_cleanup(&state->txb); + + adv748x_unregister_clients(state); + adv748x_dt_cleanup(state); + mutex_destroy(&state->mutex); + + kfree(state); + + return 0; +} + +static const struct i2c_device_id adv748x_id[] = { + { "adv7481", 0 }, + { "adv7482", 0 }, + { }, +}; + +static const struct of_device_id adv748x_of_table[] = { + { .compatible = "adi,adv7481", }, + { .compatible = "adi,adv7482", }, + { } +}; +MODULE_DEVICE_TABLE(of, adv748x_of_table); + +static struct i2c_driver adv748x_driver = { + .driver = { + .name = "adv748x", + .of_match_table = adv748x_of_table, + }, + .probe = adv748x_probe, + .remove = adv748x_remove, + .id_table = adv748x_id, +}; + +module_i2c_driver(adv748x_driver); + +MODULE_AUTHOR("Kieran Bingham <kieran.bingham@ideasonboard.com>"); +MODULE_DESCRIPTION("ADV748X video decoder"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/media/i2c/adv748x/adv748x-csi2.c b/drivers/media/i2c/adv748x/adv748x-csi2.c new file mode 100644 index 000000000000..a9b7fbd93530 --- /dev/null +++ b/drivers/media/i2c/adv748x/adv748x-csi2.c @@ -0,0 +1,323 @@ +/* + * Driver for Analog Devices ADV748X CSI-2 Transmitter + * + * Copyright (C) 2017 Renesas Electronics Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/module.h> +#include <linux/mutex.h> + +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-ioctl.h> + +#include "adv748x.h" + +static bool is_txa(struct adv748x_csi2 *tx) +{ + return tx == &tx->state->txa; +} + +static int adv748x_csi2_set_virtual_channel(struct adv748x_csi2 *tx, + unsigned int vc) +{ + return tx_write(tx, ADV748X_CSI_VC_REF, vc << ADV748X_CSI_VC_REF_SHIFT); +} + +/** + * adv748x_csi2_register_link : Register and link internal entities + * + * @tx: CSI2 private entity + * @v4l2_dev: Video registration device + * @src: Source subdevice to establish link + * @src_pad: Pad number of source to link to this @tx + * @preferred: Specify if this link is preferred over pre-existing links + * + * Ensure that the subdevice is registered against the v4l2_device, and link the + * source pad to the sink pad of the CSI2 bus entity. + */ +static int adv748x_csi2_register_link(struct adv748x_csi2 *tx, + struct v4l2_device *v4l2_dev, + struct v4l2_subdev *src, + unsigned int src_pad, + bool preferred) +{ + int enabled = 0; + int ret; + + if (preferred) + enabled = MEDIA_LNK_FL_ENABLED; + + if (!src->v4l2_dev) { + ret = v4l2_device_register_subdev(v4l2_dev, src); + if (ret) + return ret; + } + + return media_create_pad_link(&src->entity, src_pad, + &tx->sd.entity, ADV748X_CSI2_SINK, + enabled); +} + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_internal_ops + * + * We use the internal registered operation to be able to ensure that our + * incremental subdevices (not connected in the forward path) can be registered + * against the resulting video path and media device. + */ + +static int adv748x_csi2_registered(struct v4l2_subdev *sd) +{ + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); + struct adv748x_state *state = tx->state; + int ret; + + adv_dbg(state, "Registered %s (%s)", is_txa(tx) ? "TXA":"TXB", + sd->name); + + ret = adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->afe.sd, + ADV748X_AFE_SOURCE, !is_txa(tx)); + if (ret) + return ret; + + /* TX-B only supports AFE */ + if (!is_txa(tx)) + return 0; + + return adv748x_csi2_register_link(tx, sd->v4l2_dev, &state->hdmi.sd, + ADV748X_HDMI_SOURCE, true); +} + +static const struct v4l2_subdev_internal_ops adv748x_csi2_internal_ops = { + .registered = adv748x_csi2_registered, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_video_ops + */ + +static int adv748x_csi2_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); + struct v4l2_subdev *src; + + src = adv748x_get_remote_sd(&tx->pads[ADV748X_CSI2_SINK]); + if (!src) + return -EPIPE; + + return v4l2_subdev_call(src, video, s_stream, enable); +} + +static const struct v4l2_subdev_video_ops adv748x_csi2_video_ops = { + .s_stream = adv748x_csi2_s_stream, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_pad_ops + * + * The CSI2 bus pads are ignorant to the data sizes or formats. + * But we must support setting the pad formats for format propagation. + */ + +static struct v4l2_mbus_framefmt * +adv748x_csi2_get_pad_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + unsigned int pad, u32 which) +{ + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); + + if (which == V4L2_SUBDEV_FORMAT_TRY) + return v4l2_subdev_get_try_format(sd, cfg, pad); + else + return &tx->format; +} + +static int adv748x_csi2_get_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); + struct adv748x_state *state = tx->state; + struct v4l2_mbus_framefmt *mbusformat; + + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, + sdformat->which); + if (!mbusformat) + return -EINVAL; + + mutex_lock(&state->mutex); + + sdformat->format = *mbusformat; + + mutex_unlock(&state->mutex); + + return 0; +} + +static int adv748x_csi2_set_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct adv748x_csi2 *tx = adv748x_sd_to_csi2(sd); + struct adv748x_state *state = tx->state; + struct v4l2_mbus_framefmt *mbusformat; + int ret = 0; + + mbusformat = adv748x_csi2_get_pad_format(sd, cfg, sdformat->pad, + sdformat->which); + if (!mbusformat) + return -EINVAL; + + mutex_lock(&state->mutex); + + if (sdformat->pad == ADV748X_CSI2_SOURCE) { + const struct v4l2_mbus_framefmt *sink_fmt; + + sink_fmt = adv748x_csi2_get_pad_format(sd, cfg, + ADV748X_CSI2_SINK, + sdformat->which); + + if (!sink_fmt) { + ret = -EINVAL; + goto unlock; + } + + sdformat->format = *sink_fmt; + } + + *mbusformat = sdformat->format; + +unlock: + mutex_unlock(&state->mutex); + + return ret; +} + +static const struct v4l2_subdev_pad_ops adv748x_csi2_pad_ops = { + .get_fmt = adv748x_csi2_get_format, + .set_fmt = adv748x_csi2_set_format, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_ops + */ + +static const struct v4l2_subdev_ops adv748x_csi2_ops = { + .video = &adv748x_csi2_video_ops, + .pad = &adv748x_csi2_pad_ops, +}; + +/* ----------------------------------------------------------------------------- + * Subdev module and controls + */ + +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate) +{ + struct v4l2_ctrl *ctrl; + + ctrl = v4l2_ctrl_find(sd->ctrl_handler, V4L2_CID_PIXEL_RATE); + if (!ctrl) + return -EINVAL; + + return v4l2_ctrl_s_ctrl_int64(ctrl, rate); +} + +static int adv748x_csi2_s_ctrl(struct v4l2_ctrl *ctrl) +{ + switch (ctrl->id) { + case V4L2_CID_PIXEL_RATE: + return 0; + default: + return -EINVAL; + } +} + +static const struct v4l2_ctrl_ops adv748x_csi2_ctrl_ops = { + .s_ctrl = adv748x_csi2_s_ctrl, +}; + +static int adv748x_csi2_init_controls(struct adv748x_csi2 *tx) +{ + struct v4l2_ctrl *ctrl; + + v4l2_ctrl_handler_init(&tx->ctrl_hdl, 1); + + ctrl = v4l2_ctrl_new_std(&tx->ctrl_hdl, &adv748x_csi2_ctrl_ops, + V4L2_CID_PIXEL_RATE, 1, INT_MAX, 1, 1); + + tx->sd.ctrl_handler = &tx->ctrl_hdl; + if (tx->ctrl_hdl.error) { + v4l2_ctrl_handler_free(&tx->ctrl_hdl); + return tx->ctrl_hdl.error; + } + + return v4l2_ctrl_handler_setup(&tx->ctrl_hdl); +} + +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx) +{ + struct device_node *ep; + int ret; + + /* We can not use container_of to get back to the state with two TXs */ + tx->state = state; + tx->page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB; + + ep = state->endpoints[is_txa(tx) ? ADV748X_PORT_TXA : ADV748X_PORT_TXB]; + if (!ep) { + adv_err(state, "No endpoint found for %s\n", + is_txa(tx) ? "txa" : "txb"); + return -ENODEV; + } + + /* Initialise the virtual channel */ + adv748x_csi2_set_virtual_channel(tx, 0); + + adv748x_subdev_init(&tx->sd, state, &adv748x_csi2_ops, + MEDIA_ENT_F_UNKNOWN, + is_txa(tx) ? "txa" : "txb"); + + /* Ensure that matching is based upon the endpoint fwnodes */ + tx->sd.fwnode = of_fwnode_handle(ep); + + /* Register internal ops for incremental subdev registration */ + tx->sd.internal_ops = &adv748x_csi2_internal_ops; + + tx->pads[ADV748X_CSI2_SINK].flags = MEDIA_PAD_FL_SINK; + tx->pads[ADV748X_CSI2_SOURCE].flags = MEDIA_PAD_FL_SOURCE; + + ret = media_entity_pads_init(&tx->sd.entity, ADV748X_CSI2_NR_PADS, + tx->pads); + if (ret) + return ret; + + ret = adv748x_csi2_init_controls(tx); + if (ret) + goto err_free_media; + + ret = v4l2_async_register_subdev(&tx->sd); + if (ret) + goto err_free_ctrl; + + return 0; + +err_free_ctrl: + v4l2_ctrl_handler_free(&tx->ctrl_hdl); +err_free_media: + media_entity_cleanup(&tx->sd.entity); + + return ret; +} + +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx) +{ + v4l2_async_unregister_subdev(&tx->sd); + media_entity_cleanup(&tx->sd.entity); + v4l2_ctrl_handler_free(&tx->ctrl_hdl); +} diff --git a/drivers/media/i2c/adv748x/adv748x-hdmi.c b/drivers/media/i2c/adv748x/adv748x-hdmi.c new file mode 100644 index 000000000000..8f02c851bbc0 --- /dev/null +++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c @@ -0,0 +1,652 @@ +/* + * Driver for Analog Devices ADV748X HDMI receiver and Component Processor (CP) + * + * Copyright (C) 2017 Renesas Electronics Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/module.h> +#include <linux/mutex.h> + +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-dv-timings.h> +#include <media/v4l2-ioctl.h> + +#include <uapi/linux/v4l2-dv-timings.h> + +#include "adv748x.h" + +/* ----------------------------------------------------------------------------- + * HDMI and CP + */ + +#define ADV748X_HDMI_MIN_WIDTH 640 +#define ADV748X_HDMI_MAX_WIDTH 1920 +#define ADV748X_HDMI_MIN_HEIGHT 480 +#define ADV748X_HDMI_MAX_HEIGHT 1200 +#define ADV748X_HDMI_MIN_PIXELCLOCK 0 /* unknown */ +#define ADV748X_HDMI_MAX_PIXELCLOCK 162000000 + +static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = { + .type = V4L2_DV_BT_656_1120, + /* keep this initialization for compatibility with GCC < 4.4.6 */ + .reserved = { 0 }, + /* Min pixelclock value is unknown */ + V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH, + ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT, + ADV748X_HDMI_MIN_PIXELCLOCK, + ADV748X_HDMI_MAX_PIXELCLOCK, + V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT, + V4L2_DV_BT_CAP_INTERLACED | + V4L2_DV_BT_CAP_PROGRESSIVE) +}; + +struct adv748x_hdmi_video_standards { + struct v4l2_dv_timings timings; + u8 vid_std; + u8 v_freq; +}; + +static const struct adv748x_hdmi_video_standards +adv748x_hdmi_video_standards[] = { + { V4L2_DV_BT_CEA_720X480I59_94, 0x40, 0x00 }, + { V4L2_DV_BT_CEA_720X576I50, 0x41, 0x01 }, + { V4L2_DV_BT_CEA_720X480P59_94, 0x4a, 0x00 }, + { V4L2_DV_BT_CEA_720X576P50, 0x4b, 0x00 }, + { V4L2_DV_BT_CEA_1280X720P60, 0x53, 0x00 }, + { V4L2_DV_BT_CEA_1280X720P50, 0x53, 0x01 }, + { V4L2_DV_BT_CEA_1280X720P30, 0x53, 0x02 }, + { V4L2_DV_BT_CEA_1280X720P25, 0x53, 0x03 }, + { V4L2_DV_BT_CEA_1280X720P24, 0x53, 0x04 }, + { V4L2_DV_BT_CEA_1920X1080I60, 0x54, 0x00 }, + { V4L2_DV_BT_CEA_1920X1080I50, 0x54, 0x01 }, + { V4L2_DV_BT_CEA_1920X1080P60, 0x5e, 0x00 }, + { V4L2_DV_BT_CEA_1920X1080P50, 0x5e, 0x01 }, + { V4L2_DV_BT_CEA_1920X1080P30, 0x5e, 0x02 }, + { V4L2_DV_BT_CEA_1920X1080P25, 0x5e, 0x03 }, + { V4L2_DV_BT_CEA_1920X1080P24, 0x5e, 0x04 }, + /* SVGA */ + { V4L2_DV_BT_DMT_800X600P56, 0x80, 0x00 }, + { V4L2_DV_BT_DMT_800X600P60, 0x81, 0x00 }, + { V4L2_DV_BT_DMT_800X600P72, 0x82, 0x00 }, + { V4L2_DV_BT_DMT_800X600P75, 0x83, 0x00 }, + { V4L2_DV_BT_DMT_800X600P85, 0x84, 0x00 }, + /* SXGA */ + { V4L2_DV_BT_DMT_1280X1024P60, 0x85, 0x00 }, + { V4L2_DV_BT_DMT_1280X1024P75, 0x86, 0x00 }, + /* VGA */ + { V4L2_DV_BT_DMT_640X480P60, 0x88, 0x00 }, + { V4L2_DV_BT_DMT_640X480P72, 0x89, 0x00 }, + { V4L2_DV_BT_DMT_640X480P75, 0x8a, 0x00 }, + { V4L2_DV_BT_DMT_640X480P85, 0x8b, 0x00 }, + /* XGA */ + { V4L2_DV_BT_DMT_1024X768P60, 0x8c, 0x00 }, + { V4L2_DV_BT_DMT_1024X768P70, 0x8d, 0x00 }, + { V4L2_DV_BT_DMT_1024X768P75, 0x8e, 0x00 }, + { V4L2_DV_BT_DMT_1024X768P85, 0x8f, 0x00 }, + /* UXGA */ + { V4L2_DV_BT_DMT_1600X1200P60, 0x96, 0x00 }, +}; + +static void adv748x_hdmi_fill_format(struct adv748x_hdmi *hdmi, + struct v4l2_mbus_framefmt *fmt) +{ + memset(fmt, 0, sizeof(*fmt)); + + fmt->code = MEDIA_BUS_FMT_RGB888_1X24; + fmt->colorspace = V4L2_COLORSPACE_SRGB; + fmt->field = hdmi->timings.bt.interlaced ? + V4L2_FIELD_INTERLACED : V4L2_FIELD_NONE; + + fmt->width = hdmi->timings.bt.width; + fmt->height = hdmi->timings.bt.height; +} + +static void adv748x_fill_optional_dv_timings(struct v4l2_dv_timings *timings) +{ + v4l2_find_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, + 250000, NULL, NULL); +} + +static bool adv748x_hdmi_has_signal(struct adv748x_state *state) +{ + int val; + + /* Check that VERT_FILTER and DE_REGEN is locked */ + val = hdmi_read(state, ADV748X_HDMI_LW1); + return (val & ADV748X_HDMI_LW1_VERT_FILTER) && + (val & ADV748X_HDMI_LW1_DE_REGEN); +} + +static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state) +{ + int a, b; + + a = hdmi_read(state, ADV748X_HDMI_TMDS_1); + b = hdmi_read(state, ADV748X_HDMI_TMDS_2); + if (a < 0 || b < 0) + return -ENODATA; + + /* + * The High 9 bits store TMDS frequency measurement in MHz + * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency + * measurement in 1/128 MHz + */ + return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128; +} + +/* + * adv748x_hdmi_set_de_timings: Adjust horizontal picture offset through DE + * + * HDMI CP uses a Data Enable synchronisation timing reference + * + * Vary the leading and trailing edge position of the DE signal output by the CP + * core. Values are stored as signed-twos-complement in one-pixel-clock units + * + * The start and end are shifted equally by the 10-bit shift value. + */ +static void adv748x_hdmi_set_de_timings(struct adv748x_state *state, int shift) +{ + u8 high, low; + + /* POS_HIGH stores bits 8 and 9 of both the start and end */ + high = ADV748X_CP_DE_POS_HIGH_SET; + high |= (shift & 0x300) >> 8; + low = shift & 0xff; + + /* The sequence of the writes is important and must be followed */ + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); + cp_write(state, ADV748X_CP_DE_POS_END_LOW, low); + + high |= (shift & 0x300) >> 6; + + cp_write(state, ADV748X_CP_DE_POS_HIGH, high); + cp_write(state, ADV748X_CP_DE_POS_START_LOW, low); +} + +static int adv748x_hdmi_set_video_timings(struct adv748x_state *state, + const struct v4l2_dv_timings *timings) +{ + const struct adv748x_hdmi_video_standards *stds = + adv748x_hdmi_video_standards; + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(adv748x_hdmi_video_standards); i++) { + if (!v4l2_match_dv_timings(timings, &stds[i].timings, 250000, + false)) + continue; + } + + if (i >= ARRAY_SIZE(adv748x_hdmi_video_standards)) + return -EINVAL; + + /* + * When setting cp_vid_std to either 720p, 1080i, or 1080p, the video + * will get shifted horizontally to the left in active video mode. + * The de_h_start and de_h_end controls are used to centre the picture + * correctly + */ + switch (stds[i].vid_std) { + case 0x53: /* 720p */ + adv748x_hdmi_set_de_timings(state, -40); + break; + case 0x54: /* 1080i */ + case 0x5e: /* 1080p */ + adv748x_hdmi_set_de_timings(state, -44); + break; + default: + adv748x_hdmi_set_de_timings(state, 0); + break; + } + + io_write(state, ADV748X_IO_VID_STD, stds[i].vid_std); + io_clrset(state, ADV748X_IO_DATAPATH, ADV748X_IO_DATAPATH_VFREQ_M, + stds[i].v_freq << ADV748X_IO_DATAPATH_VFREQ_SHIFT); + + return 0; +} + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_video_ops + */ + +static int adv748x_hdmi_s_dv_timings(struct v4l2_subdev *sd, + struct v4l2_dv_timings *timings) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + int ret; + + if (!timings) + return -EINVAL; + + if (v4l2_match_dv_timings(&hdmi->timings, timings, 0, false)) + return 0; + + if (!v4l2_valid_dv_timings(timings, &adv748x_hdmi_timings_cap, + NULL, NULL)) + return -ERANGE; + + adv748x_fill_optional_dv_timings(timings); + + mutex_lock(&state->mutex); + + ret = adv748x_hdmi_set_video_timings(state, timings); + if (ret) + goto error; + + hdmi->timings = *timings; + + cp_clrset(state, ADV748X_CP_VID_ADJ_2, ADV748X_CP_VID_ADJ_2_INTERLACED, + timings->bt.interlaced ? + ADV748X_CP_VID_ADJ_2_INTERLACED : 0); + + mutex_unlock(&state->mutex); + + return 0; + +error: + mutex_unlock(&state->mutex); + return ret; +} + +static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd, + struct v4l2_dv_timings *timings) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + + mutex_lock(&state->mutex); + + *timings = hdmi->timings; + + mutex_unlock(&state->mutex); + + return 0; +} + +static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd, + struct v4l2_dv_timings *timings) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + struct v4l2_bt_timings *bt = &timings->bt; + int pixelclock; + int polarity; + + if (!timings) + return -EINVAL; + + memset(timings, 0, sizeof(struct v4l2_dv_timings)); + + if (!adv748x_hdmi_has_signal(state)) + return -ENOLINK; + + pixelclock = adv748x_hdmi_read_pixelclock(state); + if (pixelclock < 0) + return -ENODATA; + + timings->type = V4L2_DV_BT_656_1120; + + bt->pixelclock = pixelclock; + bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) & + ADV748X_HDMI_F1H1_INTERLACED ? + V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; + bt->width = hdmi_read16(state, ADV748X_HDMI_LW1, + ADV748X_HDMI_LW1_WIDTH_MASK); + bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1, + ADV748X_HDMI_F0H1_HEIGHT_MASK); + bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH, + ADV748X_HDMI_HFRONT_PORCH_MASK); + bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH, + ADV748X_HDMI_HSYNC_WIDTH_MASK); + bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH, + ADV748X_HDMI_HBACK_PORCH_MASK); + bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH, + ADV748X_HDMI_VFRONT_PORCH_MASK) / 2; + bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH, + ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2; + bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH, + ADV748X_HDMI_VBACK_PORCH_MASK) / 2; + + + polarity = hdmi_read(state, 0x05); + bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) | + (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0); + + if (bt->interlaced == V4L2_DV_INTERLACED) { + bt->height += hdmi_read16(state, 0x0b, 0x1fff); + bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2; + bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2; + bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2; + } + + adv748x_fill_optional_dv_timings(timings); + + /* + * No interrupt handling is implemented yet. + * There should be an IRQ when a cable is plugged and the new timings + * should be figured out and stored to state. + */ + hdmi->timings = *timings; + + return 0; +} + +static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + + mutex_lock(&state->mutex); + + *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL; + + mutex_unlock(&state->mutex); + + return 0; +} + +static int adv748x_hdmi_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + int ret; + + mutex_lock(&state->mutex); + + ret = adv748x_txa_power(state, enable); + if (ret) + goto done; + + if (adv748x_hdmi_has_signal(state)) + adv_dbg(state, "Detected HDMI signal\n"); + else + adv_dbg(state, "Couldn't detect HDMI video signal\n"); + +done: + mutex_unlock(&state->mutex); + return ret; +} + +static int adv748x_hdmi_g_pixelaspect(struct v4l2_subdev *sd, + struct v4l2_fract *aspect) +{ + aspect->numerator = 1; + aspect->denominator = 1; + + return 0; +} + +static const struct v4l2_subdev_video_ops adv748x_video_ops_hdmi = { + .s_dv_timings = adv748x_hdmi_s_dv_timings, + .g_dv_timings = adv748x_hdmi_g_dv_timings, + .query_dv_timings = adv748x_hdmi_query_dv_timings, + .g_input_status = adv748x_hdmi_g_input_status, + .s_stream = adv748x_hdmi_s_stream, + .g_pixelaspect = adv748x_hdmi_g_pixelaspect, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_pad_ops + */ + +static int adv748x_hdmi_set_pixelrate(struct adv748x_hdmi *hdmi) +{ + struct v4l2_subdev *tx; + struct v4l2_dv_timings timings; + struct v4l2_bt_timings *bt = &timings.bt; + unsigned int fps; + + tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]); + if (!tx) + return -ENOLINK; + + adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings); + + fps = DIV_ROUND_CLOSEST(bt->pixelclock, + V4L2_DV_BT_FRAME_WIDTH(bt) * + V4L2_DV_BT_FRAME_HEIGHT(bt)); + + return adv748x_csi2_set_pixelrate(tx, bt->width * bt->height * fps); +} + +static int adv748x_hdmi_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->index != 0) + return -EINVAL; + + code->code = MEDIA_BUS_FMT_RGB888_1X24; + + return 0; +} + +static int adv748x_hdmi_get_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd); + struct v4l2_mbus_framefmt *mbusformat; + + if (sdformat->pad != ADV748X_HDMI_SOURCE) + return -EINVAL; + + if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) { + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); + sdformat->format = *mbusformat; + } else { + adv748x_hdmi_fill_format(hdmi, &sdformat->format); + adv748x_hdmi_set_pixelrate(hdmi); + } + + return 0; +} + +static int adv748x_hdmi_set_format(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *sdformat) +{ + struct v4l2_mbus_framefmt *mbusformat; + + if (sdformat->pad != ADV748X_HDMI_SOURCE) + return -EINVAL; + + if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE) + return adv748x_hdmi_get_format(sd, cfg, sdformat); + + mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad); + *mbusformat = sdformat->format; + + return 0; +} + +static bool adv748x_hdmi_check_dv_timings(const struct v4l2_dv_timings *timings, + void *hdl) +{ + const struct adv748x_hdmi_video_standards *stds = + adv748x_hdmi_video_standards; + unsigned int i; + + for (i = 0; stds[i].timings.bt.width; i++) + if (v4l2_match_dv_timings(timings, &stds[i].timings, 0, false)) + return true; + + return false; +} + +static int adv748x_hdmi_enum_dv_timings(struct v4l2_subdev *sd, + struct v4l2_enum_dv_timings *timings) +{ + return v4l2_enum_dv_timings_cap(timings, &adv748x_hdmi_timings_cap, + adv748x_hdmi_check_dv_timings, NULL); +} + +static int adv748x_hdmi_dv_timings_cap(struct v4l2_subdev *sd, + struct v4l2_dv_timings_cap *cap) +{ + *cap = adv748x_hdmi_timings_cap; + return 0; +} + +static const struct v4l2_subdev_pad_ops adv748x_pad_ops_hdmi = { + .enum_mbus_code = adv748x_hdmi_enum_mbus_code, + .set_fmt = adv748x_hdmi_set_format, + .get_fmt = adv748x_hdmi_get_format, + .dv_timings_cap = adv748x_hdmi_dv_timings_cap, + .enum_dv_timings = adv748x_hdmi_enum_dv_timings, +}; + +/* ----------------------------------------------------------------------------- + * v4l2_subdev_ops + */ + +static const struct v4l2_subdev_ops adv748x_ops_hdmi = { + .video = &adv748x_video_ops_hdmi, + .pad = &adv748x_pad_ops_hdmi, +}; + +/* ----------------------------------------------------------------------------- + * Controls + */ + +static const char * const hdmi_ctrl_patgen_menu[] = { + "Disabled", + "Plain Blue", + "Color Bars", + "Ramp Grey", + "Ramp Blue", + "Ramp Red", + "Checkered" +}; + +static int adv748x_hdmi_s_ctrl(struct v4l2_ctrl *ctrl) +{ + struct adv748x_hdmi *hdmi = adv748x_ctrl_to_hdmi(ctrl); + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + int ret; + u8 pattern; + + /* Enable video adjustment first */ + ret = cp_clrset(state, ADV748X_CP_VID_ADJ, + ADV748X_CP_VID_ADJ_ENABLE, + ADV748X_CP_VID_ADJ_ENABLE); + if (ret < 0) + return ret; + + switch (ctrl->id) { + case V4L2_CID_BRIGHTNESS: + ret = cp_write(state, ADV748X_CP_BRI, ctrl->val); + break; + case V4L2_CID_HUE: + ret = cp_write(state, ADV748X_CP_HUE, ctrl->val); + break; + case V4L2_CID_CONTRAST: + ret = cp_write(state, ADV748X_CP_CON, ctrl->val); + break; + case V4L2_CID_SATURATION: + ret = cp_write(state, ADV748X_CP_SAT, ctrl->val); + break; + case V4L2_CID_TEST_PATTERN: + pattern = ctrl->val; + + /* Pattern is 0-indexed. Ctrl Menu is 1-indexed */ + if (pattern) { + pattern--; + pattern |= ADV748X_CP_PAT_GEN_EN; + } + + ret = cp_write(state, ADV748X_CP_PAT_GEN, pattern); + + break; + default: + return -EINVAL; + } + + return ret; +} + +static const struct v4l2_ctrl_ops adv748x_hdmi_ctrl_ops = { + .s_ctrl = adv748x_hdmi_s_ctrl, +}; + +static int adv748x_hdmi_init_controls(struct adv748x_hdmi *hdmi) +{ + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + + v4l2_ctrl_handler_init(&hdmi->ctrl_hdl, 5); + + /* Use our mutex for the controls */ + hdmi->ctrl_hdl.lock = &state->mutex; + + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, + V4L2_CID_BRIGHTNESS, ADV748X_CP_BRI_MIN, + ADV748X_CP_BRI_MAX, 1, ADV748X_CP_BRI_DEF); + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, + V4L2_CID_CONTRAST, ADV748X_CP_CON_MIN, + ADV748X_CP_CON_MAX, 1, ADV748X_CP_CON_DEF); + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, + V4L2_CID_SATURATION, ADV748X_CP_SAT_MIN, + ADV748X_CP_SAT_MAX, 1, ADV748X_CP_SAT_DEF); + v4l2_ctrl_new_std(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, + V4L2_CID_HUE, ADV748X_CP_HUE_MIN, + ADV748X_CP_HUE_MAX, 1, ADV748X_CP_HUE_DEF); + + v4l2_ctrl_new_std_menu_items(&hdmi->ctrl_hdl, &adv748x_hdmi_ctrl_ops, + V4L2_CID_TEST_PATTERN, + ARRAY_SIZE(hdmi_ctrl_patgen_menu) - 1, + 0, 0, hdmi_ctrl_patgen_menu); + + hdmi->sd.ctrl_handler = &hdmi->ctrl_hdl; + if (hdmi->ctrl_hdl.error) { + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); + return hdmi->ctrl_hdl.error; + } + + return v4l2_ctrl_handler_setup(&hdmi->ctrl_hdl); +} + +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi) +{ + struct adv748x_state *state = adv748x_hdmi_to_state(hdmi); + static const struct v4l2_dv_timings cea720x480 = + V4L2_DV_BT_CEA_720X480I59_94; + int ret; + + hdmi->timings = cea720x480; + + adv748x_subdev_init(&hdmi->sd, state, &adv748x_ops_hdmi, + MEDIA_ENT_F_IO_DTV, "hdmi"); + + hdmi->pads[ADV748X_HDMI_SINK].flags = MEDIA_PAD_FL_SINK; + hdmi->pads[ADV748X_HDMI_SOURCE].flags = MEDIA_PAD_FL_SOURCE; + + ret = media_entity_pads_init(&hdmi->sd.entity, + ADV748X_HDMI_NR_PADS, hdmi->pads); + if (ret) + return ret; + + ret = adv748x_hdmi_init_controls(hdmi); + if (ret) + goto err_free_media; + + return 0; + +err_free_media: + media_entity_cleanup(&hdmi->sd.entity); + + return ret; +} + +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi) +{ + v4l2_device_unregister_subdev(&hdmi->sd); + media_entity_cleanup(&hdmi->sd.entity); + v4l2_ctrl_handler_free(&hdmi->ctrl_hdl); +} diff --git a/drivers/media/i2c/adv748x/adv748x.h b/drivers/media/i2c/adv748x/adv748x.h new file mode 100644 index 000000000000..2f36e5052f08 --- /dev/null +++ b/drivers/media/i2c/adv748x/adv748x.h @@ -0,0 +1,415 @@ +/* + * Driver for Analog Devices ADV748X video decoder and HDMI receiver + * + * Copyright (C) 2017 Renesas Electronics Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Authors: + * Koji Matsuoka <koji.matsuoka.xm@renesas.com> + * Niklas Söderlund <niklas.soderlund@ragnatech.se> + * Kieran Bingham <kieran.bingham@ideasonboard.com> + * + * The ADV748x range of receivers have the following configurations: + * + * Analog HDMI MHL 4-Lane 1-Lane + * In In CSI CSI + * ADV7480 X X X + * ADV7481 X X X X X + * ADV7482 X X X X + */ + +#include <linux/i2c.h> + +#ifndef _ADV748X_H_ +#define _ADV748X_H_ + +/* I2C slave addresses */ +#define ADV748X_I2C_IO 0x70 /* IO Map */ +#define ADV748X_I2C_DPLL 0x26 /* DPLL Map */ +#define ADV748X_I2C_CP 0x22 /* CP Map */ +#define ADV748X_I2C_HDMI 0x34 /* HDMI Map */ +#define ADV748X_I2C_EDID 0x36 /* EDID Map */ +#define ADV748X_I2C_REPEATER 0x32 /* HDMI RX Repeater Map */ +#define ADV748X_I2C_INFOFRAME 0x31 /* HDMI RX InfoFrame Map */ +#define ADV748X_I2C_CEC 0x41 /* CEC Map */ +#define ADV748X_I2C_SDP 0x79 /* SDP Map */ +#define ADV748X_I2C_TXB 0x48 /* CSI-TXB Map */ +#define ADV748X_I2C_TXA 0x4a /* CSI-TXA Map */ + +enum adv748x_page { + ADV748X_PAGE_IO, + ADV748X_PAGE_DPLL, + ADV748X_PAGE_CP, + ADV748X_PAGE_HDMI, + ADV748X_PAGE_EDID, + ADV748X_PAGE_REPEATER, + ADV748X_PAGE_INFOFRAME, + ADV748X_PAGE_CEC, + ADV748X_PAGE_SDP, + ADV748X_PAGE_TXB, + ADV748X_PAGE_TXA, + ADV748X_PAGE_MAX, + + /* Fake pages for register sequences */ + ADV748X_PAGE_WAIT, /* Wait x msec */ + ADV748X_PAGE_EOR, /* End Mark */ +}; + +/** + * enum adv748x_ports - Device tree port number definitions + * + * The ADV748X ports define the mapping between subdevices + * and the device tree specification + */ +enum adv748x_ports { + ADV748X_PORT_AIN0 = 0, + ADV748X_PORT_AIN1 = 1, + ADV748X_PORT_AIN2 = 2, + ADV748X_PORT_AIN3 = 3, + ADV748X_PORT_AIN4 = 4, + ADV748X_PORT_AIN5 = 5, + ADV748X_PORT_AIN6 = 6, + ADV748X_PORT_AIN7 = 7, + ADV748X_PORT_HDMI = 8, + ADV748X_PORT_TTL = 9, + ADV748X_PORT_TXA = 10, + ADV748X_PORT_TXB = 11, + ADV748X_PORT_MAX = 12, +}; + +enum adv748x_csi2_pads { + ADV748X_CSI2_SINK, + ADV748X_CSI2_SOURCE, + ADV748X_CSI2_NR_PADS, +}; + +/* CSI2 transmitters can have 2 internal connections, HDMI/AFE */ +#define ADV748X_CSI2_MAX_SUBDEVS 2 + +struct adv748x_csi2 { + struct adv748x_state *state; + struct v4l2_mbus_framefmt format; + unsigned int page; + + struct media_pad pads[ADV748X_CSI2_NR_PADS]; + struct v4l2_ctrl_handler ctrl_hdl; + struct v4l2_subdev sd; +}; + +#define notifier_to_csi2(n) container_of(n, struct adv748x_csi2, notifier) +#define adv748x_sd_to_csi2(sd) container_of(sd, struct adv748x_csi2, sd) + +enum adv748x_hdmi_pads { + ADV748X_HDMI_SINK, + ADV748X_HDMI_SOURCE, + ADV748X_HDMI_NR_PADS, +}; + +struct adv748x_hdmi { + struct media_pad pads[ADV748X_HDMI_NR_PADS]; + struct v4l2_ctrl_handler ctrl_hdl; + struct v4l2_subdev sd; + struct v4l2_mbus_framefmt format; + + struct v4l2_dv_timings timings; +}; + +#define adv748x_ctrl_to_hdmi(ctrl) \ + container_of(ctrl->handler, struct adv748x_hdmi, ctrl_hdl) +#define adv748x_sd_to_hdmi(sd) container_of(sd, struct adv748x_hdmi, sd) + +enum adv748x_afe_pads { + ADV748X_AFE_SINK_AIN0, + ADV748X_AFE_SINK_AIN1, + ADV748X_AFE_SINK_AIN2, + ADV748X_AFE_SINK_AIN3, + ADV748X_AFE_SINK_AIN4, + ADV748X_AFE_SINK_AIN5, + ADV748X_AFE_SINK_AIN6, + ADV748X_AFE_SINK_AIN7, + ADV748X_AFE_SOURCE, + ADV748X_AFE_NR_PADS, +}; + +struct adv748x_afe { + struct media_pad pads[ADV748X_AFE_NR_PADS]; + struct v4l2_ctrl_handler ctrl_hdl; + struct v4l2_subdev sd; + struct v4l2_mbus_framefmt format; + + bool streaming; + v4l2_std_id curr_norm; + unsigned int input; +}; + +#define adv748x_ctrl_to_afe(ctrl) \ + container_of(ctrl->handler, struct adv748x_afe, ctrl_hdl) +#define adv748x_sd_to_afe(sd) container_of(sd, struct adv748x_afe, sd) + +/** + * struct adv748x_state - State of ADV748X + * @dev: (OF) device + * @client: I2C client + * @mutex: protect global state + * + * @endpoints: parsed device node endpoints for each port + * + * @i2c_addresses I2C Page addresses + * @i2c_clients I2C clients for the page accesses + * @regmap regmap configuration pages. + * + * @hdmi: state of HDMI receiver context + * @afe: state of AFE receiver context + * @txa: state of TXA transmitter context + * @txb: state of TXB transmitter context + */ +struct adv748x_state { + struct device *dev; + struct i2c_client *client; + struct mutex mutex; + + struct device_node *endpoints[ADV748X_PORT_MAX]; + + struct i2c_client *i2c_clients[ADV748X_PAGE_MAX]; + struct regmap *regmap[ADV748X_PAGE_MAX]; + + struct adv748x_hdmi hdmi; + struct adv748x_afe afe; + struct adv748x_csi2 txa; + struct adv748x_csi2 txb; +}; + +#define adv748x_hdmi_to_state(h) container_of(h, struct adv748x_state, hdmi) +#define adv748x_afe_to_state(a) container_of(a, struct adv748x_state, afe) + +#define adv_err(a, fmt, arg...) dev_err(a->dev, fmt, ##arg) +#define adv_info(a, fmt, arg...) dev_info(a->dev, fmt, ##arg) +#define adv_dbg(a, fmt, arg...) dev_dbg(a->dev, fmt, ##arg) + +/* Register Mappings */ + +/* IO Map */ +#define ADV748X_IO_PD 0x00 /* power down controls */ +#define ADV748X_IO_PD_RX_EN BIT(6) + +#define ADV748X_IO_REG_04 0x04 +#define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */ + +#define ADV748X_IO_DATAPATH 0x03 /* datapath cntrl */ +#define ADV748X_IO_DATAPATH_VFREQ_M 0x70 +#define ADV748X_IO_DATAPATH_VFREQ_SHIFT 4 + +#define ADV748X_IO_VID_STD 0x05 + +#define ADV748X_IO_10 0x10 /* io_reg_10 */ +#define ADV748X_IO_10_CSI4_EN BIT(7) +#define ADV748X_IO_10_CSI1_EN BIT(6) +#define ADV748X_IO_10_PIX_OUT_EN BIT(5) + +#define ADV748X_IO_CHIP_REV_ID_1 0xdf +#define ADV748X_IO_CHIP_REV_ID_2 0xe0 + +#define ADV748X_IO_SLAVE_ADDR_BASE 0xf2 + +/* HDMI RX Map */ +#define ADV748X_HDMI_LW1 0x07 /* line width_1 */ +#define ADV748X_HDMI_LW1_VERT_FILTER BIT(7) +#define ADV748X_HDMI_LW1_DE_REGEN BIT(5) +#define ADV748X_HDMI_LW1_WIDTH_MASK 0x1fff + +#define ADV748X_HDMI_F0H1 0x09 /* field0 height_1 */ +#define ADV748X_HDMI_F0H1_HEIGHT_MASK 0x1fff + +#define ADV748X_HDMI_F1H1 0x0b /* field1 height_1 */ +#define ADV748X_HDMI_F1H1_INTERLACED BIT(5) + +#define ADV748X_HDMI_HFRONT_PORCH 0x20 /* hsync_front_porch_1 */ +#define ADV748X_HDMI_HFRONT_PORCH_MASK 0x1fff + +#define ADV748X_HDMI_HSYNC_WIDTH 0x22 /* hsync_pulse_width_1 */ +#define ADV748X_HDMI_HSYNC_WIDTH_MASK 0x1fff + +#define ADV748X_HDMI_HBACK_PORCH 0x24 /* hsync_back_porch_1 */ +#define ADV748X_HDMI_HBACK_PORCH_MASK 0x1fff + +#define ADV748X_HDMI_VFRONT_PORCH 0x2a /* field0_vs_front_porch_1 */ +#define ADV748X_HDMI_VFRONT_PORCH_MASK 0x3fff + +#define ADV748X_HDMI_VSYNC_WIDTH 0x2e /* field0_vs_pulse_width_1 */ +#define ADV748X_HDMI_VSYNC_WIDTH_MASK 0x3fff + +#define ADV748X_HDMI_VBACK_PORCH 0x32 /* field0_vs_back_porch_1 */ +#define ADV748X_HDMI_VBACK_PORCH_MASK 0x3fff + +#define ADV748X_HDMI_TMDS_1 0x51 /* hdmi_reg_51 */ +#define ADV748X_HDMI_TMDS_2 0x52 /* hdmi_reg_52 */ + +/* SDP Main Map */ +#define ADV748X_SDP_INSEL 0x00 /* user_map_rw_reg_00 */ + +#define ADV748X_SDP_VID_SEL 0x02 /* user_map_rw_reg_02 */ +#define ADV748X_SDP_VID_SEL_MASK 0xf0 +#define ADV748X_SDP_VID_SEL_SHIFT 4 + +/* Contrast - Unsigned*/ +#define ADV748X_SDP_CON 0x08 /* user_map_rw_reg_08 */ +#define ADV748X_SDP_CON_MIN 0 +#define ADV748X_SDP_CON_DEF 128 +#define ADV748X_SDP_CON_MAX 255 + +/* Brightness - Signed */ +#define ADV748X_SDP_BRI 0x0a /* user_map_rw_reg_0a */ +#define ADV748X_SDP_BRI_MIN -128 +#define ADV748X_SDP_BRI_DEF 0 +#define ADV748X_SDP_BRI_MAX 127 + +/* Hue - Signed, inverted*/ +#define ADV748X_SDP_HUE 0x0b /* user_map_rw_reg_0b */ +#define ADV748X_SDP_HUE_MIN -127 +#define ADV748X_SDP_HUE_DEF 0 +#define ADV748X_SDP_HUE_MAX 128 + +/* Test Patterns / Default Values */ +#define ADV748X_SDP_DEF 0x0c /* user_map_rw_reg_0c */ +#define ADV748X_SDP_DEF_VAL_EN BIT(0) /* Force free run mode */ +#define ADV748X_SDP_DEF_VAL_AUTO_EN BIT(1) /* Free run when no signal */ + +#define ADV748X_SDP_MAP_SEL 0x0e /* user_map_rw_reg_0e */ +#define ADV748X_SDP_MAP_SEL_RO_MAIN 1 + +/* Free run pattern select */ +#define ADV748X_SDP_FRP 0x14 +#define ADV748X_SDP_FRP_MASK GENMASK(3, 1) + +/* Saturation */ +#define ADV748X_SDP_SD_SAT_U 0xe3 /* user_map_rw_reg_e3 */ +#define ADV748X_SDP_SD_SAT_V 0xe4 /* user_map_rw_reg_e4 */ +#define ADV748X_SDP_SAT_MIN 0 +#define ADV748X_SDP_SAT_DEF 128 +#define ADV748X_SDP_SAT_MAX 255 + +/* SDP RO Main Map */ +#define ADV748X_SDP_RO_10 0x10 +#define ADV748X_SDP_RO_10_IN_LOCK BIT(0) + +/* CP Map */ +#define ADV748X_CP_PAT_GEN 0x37 /* int_pat_gen_1 */ +#define ADV748X_CP_PAT_GEN_EN BIT(7) + +/* Contrast Control - Unsigned */ +#define ADV748X_CP_CON 0x3a /* contrast_cntrl */ +#define ADV748X_CP_CON_MIN 0 /* Minimum contrast */ +#define ADV748X_CP_CON_DEF 128 /* Default */ +#define ADV748X_CP_CON_MAX 255 /* Maximum contrast */ + +/* Saturation Control - Unsigned */ +#define ADV748X_CP_SAT 0x3b /* saturation_cntrl */ +#define ADV748X_CP_SAT_MIN 0 /* Minimum saturation */ +#define ADV748X_CP_SAT_DEF 128 /* Default */ +#define ADV748X_CP_SAT_MAX 255 /* Maximum saturation */ + +/* Brightness Control - Signed */ +#define ADV748X_CP_BRI 0x3c /* brightness_cntrl */ +#define ADV748X_CP_BRI_MIN -128 /* Luma is -512d */ +#define ADV748X_CP_BRI_DEF 0 /* Luma is 0 */ +#define ADV748X_CP_BRI_MAX 127 /* Luma is 508d */ + +/* Hue Control */ +#define ADV748X_CP_HUE 0x3d /* hue_cntrl */ +#define ADV748X_CP_HUE_MIN 0 /* -90 degree */ +#define ADV748X_CP_HUE_DEF 0 /* -90 degree */ +#define ADV748X_CP_HUE_MAX 255 /* +90 degree */ + +#define ADV748X_CP_VID_ADJ 0x3e /* vid_adj_0 */ +#define ADV748X_CP_VID_ADJ_ENABLE BIT(7) /* Enable colour controls */ + +#define ADV748X_CP_DE_POS_HIGH 0x8b /* de_pos_adj_6 */ +#define ADV748X_CP_DE_POS_HIGH_SET BIT(6) +#define ADV748X_CP_DE_POS_END_LOW 0x8c /* de_pos_adj_7 */ +#define ADV748X_CP_DE_POS_START_LOW 0x8d /* de_pos_adj_8 */ + +#define ADV748X_CP_VID_ADJ_2 0x91 +#define ADV748X_CP_VID_ADJ_2_INTERLACED BIT(6) +#define ADV748X_CP_VID_ADJ_2_INTERLACED_3D BIT(4) + +#define ADV748X_CP_CLMP_POS 0xc9 /* clmp_pos_cntrl_4 */ +#define ADV748X_CP_CLMP_POS_DIS_AUTO BIT(0) /* dis_auto_param_buff */ + +/* CSI : TXA/TXB Maps */ +#define ADV748X_CSI_VC_REF 0x0d /* csi_tx_top_reg_0d */ +#define ADV748X_CSI_VC_REF_SHIFT 6 + +#define ADV748X_CSI_FS_AS_LS 0x1e /* csi_tx_top_reg_1e */ +#define ADV748X_CSI_FS_AS_LS_UNKNOWN BIT(6) /* Undocumented bit */ + +/* Register handling */ + +int adv748x_read(struct adv748x_state *state, u8 addr, u8 reg); +int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value); +int adv748x_write_block(struct adv748x_state *state, int client_page, + unsigned int init_reg, const void *val, + size_t val_len); + +#define io_read(s, r) adv748x_read(s, ADV748X_PAGE_IO, r) +#define io_write(s, r, v) adv748x_write(s, ADV748X_PAGE_IO, r, v) +#define io_clrset(s, r, m, v) io_write(s, r, (io_read(s, r) & ~m) | v) + +#define hdmi_read(s, r) adv748x_read(s, ADV748X_PAGE_HDMI, r) +#define hdmi_read16(s, r, m) (((hdmi_read(s, r) << 8) | hdmi_read(s, r+1)) & m) +#define hdmi_write(s, r, v) adv748x_write(s, ADV748X_PAGE_HDMI, r, v) +#define hdmi_clrset(s, r, m, v) hdmi_write(s, r, (hdmi_read(s, r) & ~m) | v) + +#define sdp_read(s, r) adv748x_read(s, ADV748X_PAGE_SDP, r) +#define sdp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_SDP, r, v) +#define sdp_clrset(s, r, m, v) sdp_write(s, r, (sdp_read(s, r) & ~m) | v) + +#define cp_read(s, r) adv748x_read(s, ADV748X_PAGE_CP, r) +#define cp_write(s, r, v) adv748x_write(s, ADV748X_PAGE_CP, r, v) +#define cp_clrset(s, r, m, v) cp_write(s, r, (cp_read(s, r) & ~m) | v) + +#define txa_read(s, r) adv748x_read(s, ADV748X_PAGE_TXA, r) +#define txa_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXA, r, v) +#define txa_clrset(s, r, m, v) txa_write(s, r, (txa_read(s, r) & ~m) | v) + +#define txb_read(s, r) adv748x_read(s, ADV748X_PAGE_TXB, r) +#define txb_write(s, r, v) adv748x_write(s, ADV748X_PAGE_TXB, r, v) +#define txb_clrset(s, r, m, v) txb_write(s, r, (txb_read(s, r) & ~m) | v) + +#define tx_read(t, r) adv748x_read(t->state, t->page, r) +#define tx_write(t, r, v) adv748x_write(t->state, t->page, r, v) +#define tx_clrset(t, r, m, v) tx_write(t, r, (tx_read(t, r) & ~m) | v) + +static inline struct v4l2_subdev *adv748x_get_remote_sd(struct media_pad *pad) +{ + pad = media_entity_remote_pad(pad); + if (!pad) + return NULL; + + return media_entity_to_v4l2_subdev(pad->entity); +} + +void adv748x_subdev_init(struct v4l2_subdev *sd, struct adv748x_state *state, + const struct v4l2_subdev_ops *ops, u32 function, + const char *ident); + +int adv748x_register_subdevs(struct adv748x_state *state, + struct v4l2_device *v4l2_dev); + +int adv748x_txa_power(struct adv748x_state *state, bool on); +int adv748x_txb_power(struct adv748x_state *state, bool on); + +int adv748x_afe_init(struct adv748x_afe *afe); +void adv748x_afe_cleanup(struct adv748x_afe *afe); + +int adv748x_csi2_init(struct adv748x_state *state, struct adv748x_csi2 *tx); +void adv748x_csi2_cleanup(struct adv748x_csi2 *tx); +int adv748x_csi2_set_pixelrate(struct v4l2_subdev *sd, s64 rate); + +int adv748x_hdmi_init(struct adv748x_hdmi *hdmi); +void adv748x_hdmi_cleanup(struct adv748x_hdmi *hdmi); + +#endif /* _ADV748X_H_ */