@@ -34,13 +34,10 @@ This system call closes a previously opened CA device.
Return Value
------------
-.. flat-table::
- :header-rows: 0
- :stub-columns: 0
+On success 0 is returned.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
- - .. row 1
-
- - ``EBADF``
-
- - fd is not a valid open file descriptor.
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -66,33 +66,11 @@ the device in this mode will fail, and an error code will be returned.
Return Value
------------
-.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
-.. flat-table::
- :header-rows: 0
- :stub-columns: 0
+On success 0 is returned.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
- - .. row 1
-
- - ``ENODEV``
-
- - Device driver not loaded/available.
-
- - .. row 2
-
- - ``EINTERNAL``
-
- - Internal error.
-
- - .. row 3
-
- - ``EBUSY``
-
- - Device or resource busy.
-
- - .. row 4
-
- - ``EINVAL``
-
- - Invalid argument.
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -40,5 +40,7 @@ Return Value
On success 0 is returned and :c:type:`ca_caps` is filled.
On error, -1 is returned and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -49,6 +49,11 @@ Description
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -43,7 +43,15 @@ On success 0 is returned, and :c:type:`ca_slot_info` is filled.
On error -1 is returned, and the ``errno`` variable is set
appropriately.
-If the slot is not available, ``errno`` will contain ``-EINVAL``.
+.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+ :widths: 1 16
+
+ - - ``ENODEV``
+ - the slot is not available.
The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -35,6 +35,10 @@ be called before start using the CA hardware.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -38,6 +38,10 @@ Description
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -48,6 +48,10 @@ Description
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -40,6 +40,10 @@ DMX_OUT_TSDEMUX_TAP.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -35,13 +35,10 @@ previously allocated via the open() call.
Return Value
------------
-.. flat-table::
- :header-rows: 0
- :stub-columns: 0
+On success 0 is returned.
+On error, -1 is returned and the ``errno`` variable is set
+appropriately.
- - .. row 1
-
- - ``EBADF``
-
- - fd is not a valid open file descriptor.
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -69,31 +69,20 @@ using the F_SETFL command of the fcntl system call.
Return Value
------------
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
+
.. flat-table::
:header-rows: 0
:stub-columns: 0
+ :widths: 1 16
-
- - .. row 1
-
- - ``ENODEV``
-
- - Device driver not loaded/available.
-
- - .. row 2
-
- - ``EINVAL``
-
- - Invalid argument.
-
- - .. row 3
-
- - ``EMFILE``
-
+ - - ``EMFILE``
- “Too many open files”, i.e. no more filters available.
- - .. row 4
-
- - ``ENOMEM``
-
- - The driver failed to allocate enough memory.
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,54 +41,33 @@ implied by count.
Return Value
------------
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
.. flat-table::
:header-rows: 0
:stub-columns: 0
+ :widths: 1 16
+ - - ``EWOULDBLOCK``
+ - No data to return and ``O_NONBLOCK`` was specified.
- - .. row 1
-
- - ``EWOULDBLOCK``
-
- - No data to return and O_NONBLOCK was specified.
-
- - .. row 2
-
- - ``EBADF``
-
- - fd is not a valid open file descriptor.
-
- - .. row 3
-
- - ``ECRC``
-
- - Last section had a CRC error - no data returned. The buffer is
- flushed.
-
- - .. row 4
-
- - ``EOVERFLOW``
-
- -
-
- - .. row 5
-
- -
+ - - ``EOVERFLOW``
- The filtered data was not read from the buffer in due time,
resulting in non-read data being lost. The buffer is flushed.
- - .. row 6
+ - - ``ETIMEDOUT``
+ - The section was not loaded within the stated timeout period.
+ See ioctl :ref:`DMX_SET_FILTER` for how to set a timeout.
- - ``ETIMEDOUT``
+ - - ``EFAULT``
+ - The driver failed to write to the callers buffer due to an
+ invalid \*buf pointer.
- - The section was not loaded within the stated timeout period. See
- ioctl DMX_SET_FILTER for how to set a timeout.
- - .. row 7
-
- - ``EFAULT``
-
- - The driver failed to write to the callers buffer due to an invalid
- \*buf pointer.
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -44,32 +44,29 @@ The amount of data to be transferred is implied by count.
Return Value
------------
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
.. flat-table::
:header-rows: 0
:stub-columns: 0
+ :widths: 1 16
- - .. row 1
-
- - ``EWOULDBLOCK``
-
- - No data was written. This might happen if O_NONBLOCK was
+ - - ``EWOULDBLOCK``
+ - No data was written. This might happen if ``O_NONBLOCK`` was
specified and there is no more buffer space available (if
- O_NONBLOCK is not specified the function will block until buffer
+ ``O_NONBLOCK`` is not specified the function will block until buffer
space is available).
- - .. row 2
-
- - ``EBUSY``
-
+ - - ``EBUSY``
- This error code indicates that there are conflicting requests. The
corresponding demux device is setup to receive data from the
front- end. Make sure that these filters are stopped and that the
- filters with input set to DMX_IN_DVR are started.
+ filters with input set to ``DMX_IN_DVR`` are started.
- - .. row 3
-
- - ``EBADF``
-
- - fd is not a valid open file descriptor.
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -37,6 +37,10 @@ Description
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -42,17 +42,24 @@ the real 90kHz STC value is stc->stc / stc->base .
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
.. flat-table::
:header-rows: 0
:stub-columns: 0
-
+ :widths: 1 16
- .. row 1
- ``EINVAL``
- Invalid stc number.
+
+
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,6 +41,10 @@ DMX_SET_PES_FILTER or DMX_ADD_PID.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -40,6 +40,11 @@ used.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -47,6 +47,11 @@ will be canceled, and the receive buffer will be flushed.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -42,15 +42,17 @@ capability is supported.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
.. flat-table::
:header-rows: 0
:stub-columns: 0
+ :widths: 1 16
- .. row 1
@@ -61,3 +63,7 @@ appropriately. The generic error codes are described at the
There are active filters filtering data from another input source.
Make sure that these filters are stopped before starting this
filter.
+
+
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -29,15 +29,16 @@ Description
-----------
This ioctl call is used to start the actual filtering operation defined
-via the ioctl calls DMX_SET_FILTER or DMX_SET_PES_FILTER.
+via the ioctl calls :ref:`DMX_SET_FILTER` or :ref:`DMX_SET_PES_FILTER`.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
@@ -51,7 +52,7 @@ appropriately. The generic error codes are described at the
- ``EINVAL``
- Invalid argument, i.e. no filtering parameters provided via the
- DMX_SET_FILTER or DMX_SET_PES_FILTER functions.
+ :ref:`DMX_SET_FILTER` or :ref:`DMX_SET_PES_FILTER` ioctls.
- .. row 2
@@ -61,3 +62,7 @@ appropriately. The generic error codes are described at the
There are active filters filtering data from another input source.
Make sure that these filters are stopped before starting this
filter.
+
+
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -36,6 +36,10 @@ started via the DMX_START command.
Return Value
------------
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -39,6 +39,10 @@ The received message is stored at the buffer pointed by ``argp``.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -37,6 +37,10 @@ is manually powered off. Not all DVB adapters support this ioctl.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -43,6 +43,10 @@ It provides support for what's specified at
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -38,7 +38,11 @@ Sends the DiSEqC command pointed by ``argp`` to the antenna subsystem.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -46,6 +46,10 @@ dishes were already legacy in 2004.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -45,6 +45,10 @@ voltages.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -44,10 +44,10 @@ an event becomes available.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
+On success 0 is returned.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
.. flat-table::
@@ -66,3 +66,6 @@ appropriately. The generic error codes are described at the
- ``EOVERFLOW``
- Overflow in event queue - one or more events were lost.
+
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -42,11 +42,10 @@ this command, read-only access to the device is sufficient.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
-
+On success 0 is returned.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
.. flat-table::
:header-rows: 0
@@ -58,3 +57,6 @@ appropriately. The generic error codes are described at the
- ``EINVAL``
- Maximum supported symbol rate reached.
+
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -53,6 +53,10 @@ The frontend capabilities are described at :c:type:`fe_caps`.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -64,6 +64,10 @@ depends on the delivery system and on the device:
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,6 +41,10 @@ access to the device is sufficient.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,6 +41,10 @@ to the device is sufficient.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,6 +41,10 @@ to the device is sufficient.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -56,6 +56,10 @@ state changes of the frontend hardware. It is produced using the enum
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -43,6 +43,10 @@ sufficient.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -48,6 +48,10 @@ FE_TUNE_MODE_ONESHOT mode
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -48,17 +48,24 @@ requires read/write access to the device.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
-:ref:`Generic Error Codes <gen-errors>` chapter.
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
.. flat-table::
:header-rows: 0
:stub-columns: 0
-
+ :widths: 1 16
- .. row 1
- ``EINVAL``
- Maximum supported symbol rate reached.
+
+
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -49,6 +49,10 @@ this is done using the DiSEqC ioctls.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -53,6 +53,10 @@ power up the LNBf.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -41,8 +41,10 @@ down automatically.
Return Value
============
-The function returns 0 on success, -1 on failure and the ``errno`` is
-set appropriately. Possible error codes:
+On success 0 is returned.
-EBADF
- ``fd`` is not a valid open file descriptor.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+Generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -79,24 +79,32 @@ On error, -1 is returned, and the ``errno`` variable is set appropriately.
Possible error codes are:
-EACCES
- The caller has no permission to access the device.
-EBUSY
- The the device driver is already in use.
+On success 0 is returned, and :c:type:`ca_slot_info` is filled.
-ENXIO
- No device corresponding to this device special file exists.
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
-ENOMEM
- Not enough kernel memory was available to complete the request.
+.. tabularcolumns:: |p{2.5cm}|p{15.0cm}|
-EMFILE
- The process already has the maximum number of files open.
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+ :widths: 1 16
-ENFILE
- The limit on the total number of files open on the system has been
- reached.
+ - - ``EPERM``
+ - The caller has no permission to access the device.
-ENODEV
- The device got removed.
+ - - ``EBUSY``
+ - The the device driver is already in use.
+
+ - - ``EMFILE``
+ - The process already has the maximum number of files open.
+
+ - - ``ENFILE``
+ - The limit on the total number of files open on the system has been
+ reached.
+
+
+The generic error codes are described at the
+:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -78,6 +78,10 @@ filled with the number of the created interface.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned, and :c:type:`ca_slot_info` is filled.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -43,6 +43,10 @@ the ``errno`` with ``EINVAL`` error code.
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned, and :c:type:`ca_slot_info` is filled.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
@@ -39,6 +39,10 @@ The NET_REMOVE_IF ioctl deletes an interface previously created via
Return Value
============
-On success 0 is returned, on error -1 and the ``errno`` variable is set
-appropriately. The generic error codes are described at the
+On success 0 is returned, and :c:type:`ca_slot_info` is filled.
+
+On error -1 is returned, and the ``errno`` variable is set
+appropriately.
+
+The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.
There are several issues on the return value for ioctls: - Text is confusing; - Some error codes don't exist; - The non-generic error codes should come before the text that points to the generic error codes; - Tables don't contain column size hints; - Some references are not marked as such. Correct them. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> --- Documentation/media/uapi/dvb/ca-fclose.rst | 13 ++--- Documentation/media/uapi/dvb/ca-fopen.rst | 32 ++----------- Documentation/media/uapi/dvb/ca-get-cap.rst | 4 +- Documentation/media/uapi/dvb/ca-get-msg.rst | 9 +++- Documentation/media/uapi/dvb/ca-get-slot-info.rst | 10 +++- Documentation/media/uapi/dvb/ca-reset.rst | 8 +++- Documentation/media/uapi/dvb/ca-send-msg.rst | 8 +++- Documentation/media/uapi/dvb/ca-set-descr.rst | 8 +++- Documentation/media/uapi/dvb/dmx-add-pid.rst | 8 +++- Documentation/media/uapi/dvb/dmx-fclose.rst | 13 ++--- Documentation/media/uapi/dvb/dmx-fopen.rst | 33 +++++-------- Documentation/media/uapi/dvb/dmx-fread.rst | 55 +++++++--------------- Documentation/media/uapi/dvb/dmx-fwrite.rst | 29 +++++------- Documentation/media/uapi/dvb/dmx-get-pes-pids.rst | 8 +++- Documentation/media/uapi/dvb/dmx-get-stc.rst | 15 ++++-- Documentation/media/uapi/dvb/dmx-remove-pid.rst | 8 +++- .../media/uapi/dvb/dmx-set-buffer-size.rst | 9 +++- Documentation/media/uapi/dvb/dmx-set-filter.rst | 9 +++- .../media/uapi/dvb/dmx-set-pes-filter.rst | 12 +++-- Documentation/media/uapi/dvb/dmx-start.rst | 15 ++++-- Documentation/media/uapi/dvb/dmx-stop.rst | 8 +++- .../media/uapi/dvb/fe-diseqc-recv-slave-reply.rst | 8 +++- .../media/uapi/dvb/fe-diseqc-reset-overload.rst | 8 +++- .../media/uapi/dvb/fe-diseqc-send-burst.rst | 8 +++- .../media/uapi/dvb/fe-diseqc-send-master-cmd.rst | 8 +++- .../uapi/dvb/fe-dishnetwork-send-legacy-cmd.rst | 8 +++- .../media/uapi/dvb/fe-enable-high-lnb-voltage.rst | 8 +++- Documentation/media/uapi/dvb/fe-get-event.rst | 9 ++-- Documentation/media/uapi/dvb/fe-get-frontend.rst | 10 ++-- Documentation/media/uapi/dvb/fe-get-info.rst | 8 +++- Documentation/media/uapi/dvb/fe-get-property.rst | 8 +++- Documentation/media/uapi/dvb/fe-read-ber.rst | 8 +++- .../media/uapi/dvb/fe-read-signal-strength.rst | 8 +++- Documentation/media/uapi/dvb/fe-read-snr.rst | 8 +++- Documentation/media/uapi/dvb/fe-read-status.rst | 8 +++- .../media/uapi/dvb/fe-read-uncorrected-blocks.rst | 8 +++- .../media/uapi/dvb/fe-set-frontend-tune-mode.rst | 8 +++- Documentation/media/uapi/dvb/fe-set-frontend.rst | 15 ++++-- Documentation/media/uapi/dvb/fe-set-tone.rst | 8 +++- Documentation/media/uapi/dvb/fe-set-voltage.rst | 8 +++- Documentation/media/uapi/dvb/frontend_f_close.rst | 10 ++-- Documentation/media/uapi/dvb/frontend_f_open.rst | 38 +++++++++------ Documentation/media/uapi/dvb/net-add-if.rst | 8 +++- Documentation/media/uapi/dvb/net-get-if.rst | 8 +++- Documentation/media/uapi/dvb/net-remove-if.rst | 8 +++- 45 files changed, 327 insertions(+), 221 deletions(-)