| Message ID | 20220711075245.10492-1-nancy.lin@mediatek.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add MediaTek SoC(vdosys1) support for mt8195 | expand |
On Mon, 2022-07-11 at 15:52 +0800, Nancy.Lin wrote: > The hardware path of vdosys1 with DPTx output need to go through by > several modules, such as, OVL_ADAPTOR and MERGE. > > Add mmsys and mutex modules support by the patches below: > > Changes in v25: > - fix reviewer comment > - refine mtk_mmsys_reset_update func > - rebase to next-20220708 > > Changes in v24: > - fix reviewer comment > - refine mtk_mmsys_reset_update func > - rebase to next-20220622 > > Changes in v23: > - separate[7] mmsys/mutex and drm patches into two series > > Changes in v22: > - rebase to next-20220525 > - rebase to vdosys0 series v22 > - separate dts to a new patch > > Changes in v21: > - fix reviewer comment > - fix rdma and ethdr binding doc and dts > > Changes in v20: > - fix reviewer comment > - update mmsys update bit api name > - add mtk_mmsys_update_bits error message if lose gce property > - list all mt8195 vdosys1 reset bits > > Changes in v19: > - fix reviewer comment > - separate mt8195 mmsys component to a new patch > - separate mt8195 vdo0 and vdo1 routing table > - separate mmsys_write_reg api to a new patch and simplify write > reg code > - separate mmsys 64 bit reset to a new patch > - separate mtk-mutex dp_intf1 component to a new patch > > Changes in v18: > - fix reviewer comment > - fix rdma binding doc > - fix ethdr binding doc > - refine mmsys config cmdq support > - refine merge reset control flow, get reset control in probe > function > - add ethdr reset control error handling and remove dbg log > - rebase to vdosys0 series v20 (ref [5]) > > Changes in v17: > - fix reviewer comment in v16 > - separate ovl adaptor comp in mtk-mmsys and mtk-mutex > - separate mmsys config API > - move mdp_rdma binding yaml > - fix ovl adaptor pm runtime get sync timing issue > - rebase to vdosys0 series v19 (ref [5]) > - rebase to [7] for modify vblank register change > > Changes in v16: > - fix reviewer comment in v 15 > - fix mtk_drm_ddp_comp.c alignment > - fix vdosys0 mmsys num before adding vdosys1 patch > > Changes in v15: > - fix ethdr uppercase hex number in dts > > Changes in v14: > - remove MTK_MMSYS 64 bit dependency > - add ethdr.yaml back and fix dt_schema check fail > > Resend v13 > - add related maintainer in maillist > > Changes in v13: > - fix reviewer comment in v12 > - fix rdma dt-binding format > - fix dts node naming > - fix 32 bit build error > - modify 64bit dependency for mtk-mmsys > - rebase to vdosys0 series v16. (ref [5]) > > Changes in v12: > - fix reviewer comment in v11 > - modify mbox index > - refine dma dev for ovl_adaptor sub driver > > Changes in v11: > - remove ethdr vblank spin lock > - refine ovl_adaptor print message > > Changes in v10: > - refine ethdr reset control using > devm_reset_control_array_get_optional_exclusive > - fix ovl_adaptor mtk_ovl_adaptor_clk_enable error handle issue > > Changes in v9: > - rebase on kernel-5.16-rc1 > - rebase on vdosys0 series v13. (ref [5]) > - fix ovl_adaptor sub driver is brought up unintentionally > - fix clang build test fail- duplicate ethdr/mdp_rdma > init_module/cleanup_module symbol issue > > Changes in v8: > - separate merge async reset to new patch. > - separate drm ovl_adaptor sub driver to new patch. > - fix reviewer comment in v7. > > Changes in v7: > - rebase on vdosys0 series v12 (ref[5]) > - add dma description in ethdr binding document. > - refine vdosys1 bit definition of mmsys routing table. > - separate merge modification into 3 pathces. > - separate mutex modification into 2 patches. > - add plane color coding for mdp_rdma csc. > - move mdp_rdma pm control to ovl_adaptor. > - fix reviewer comment in v6. > > Changes in v6: > - rebase on kernel-5.15-rc1. > - change mbox label to gce0 for dts node of vdosys1. > - modify mmsys reset num for mt8195. > - rebase on vdosys0 series v10. (ref [5]) > - use drm to bring up ovl_adaptor driver. > - move drm iommu/mutex check from kms init to drm bind. > - modify rdma binding doc location. > (Documentation/devicetree/bindings/arm/) > - modify for reviewer's comment in v5. > > Changes in v5: > - add mmsys reset controller reference. > > Changes in v4: > - use merge common driver for merge1~4. > - refine ovl_adaptor rdma driver. > - use ovl_adaptor ddp_comp function instead of ethdr. > - modify for reviewer's comment in v3. > > Changes in v3: > - modify for reviewer's comment in v2. > - add vdosys1 2 pixels align limit. > - add mixer odd offset support. > > Changes in v2: > - Merge PSEUDO_OVL and ETHDR into one DRM component. > - Add mmsys config API for vdosys1 hardware setting. > - Add mmsys reset control using linux reset framework. > > Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com> > > This series are based on the following patch: > [1] arm64: dts: Add mediatek SoC mt8195 and evaluation board > 20220112114724.1953-4-tinghan.shen@mediatek.com > [2] arm64: dts: mt8195: add IOMMU and smi nodes > 20210615173233.26682-15-tinghan.shen@mediatek.com > [3] arm64: dts: mt8195: add gce node > 20220126090109.32143-1-jason-jh.lin@mediatek.com > [4] [v2] arm64: dts: mt8195: add display node for vdosys0 > 20220225021535.2655-1-jason-jh.lin@mediatek.com > [5] Add MediaTek SoC DRM (vdosys0) support for mt8195 - v22 series > 20220526102126.19756-1-jason-jh.lin@mediatek.com > [6] dt-bindings: mediatek: mt8195: Add binding for MM IOMMU > 20220407075726.17771-2-yong.wu@mediatek.com > [7] Add MediaTek SoC DRM (vdosys1) support for mt8195 > 20220526110233.20080-1-nancy.lin@mediatek.com > > Nancy.Lin (10): > dt-bindings: reset: mt8195: add vdosys1 reset control bit > soc: mediatek: add mtk-mmsys ethdr and mdp_rdma components > soc: mediatek: add mtk-mmsys support for mt8195 vdosys1 > soc: mediatek: add mtk_mmsys_update_bits API > soc: mediatek: add mtk-mmsys config API for mt8195 vdosys1 > soc: mediatek: add cmdq support of mtk-mmsys config API for mt8195 > vdosys1 > soc: mediatek: mmsys: add mmsys for support 64 reset bits > soc: mediatek: mmsys: add reset control for MT8195 vdosys1 > soc: mediatek: add mtk-mutex component - dp_intf1 > soc: mediatek: add mtk-mutex support for mt8195 vdosys1 > > drivers/soc/mediatek/mt8195-mmsys.h | 146 > ++++++++++++++++++++++ > drivers/soc/mediatek/mtk-mmsys.c | 132 ++++++++++++++----- > drivers/soc/mediatek/mtk-mmsys.h | 1 + > drivers/soc/mediatek/mtk-mutex.c | 37 ++++++ > include/dt-bindings/reset/mt8195-resets.h | 45 +++++++ > include/linux/soc/mediatek/mtk-mmsys.h | 25 ++++ > 6 files changed, 355 insertions(+), 31 deletions(-) > Hello Matthias, This series is about mmsys configuration of external display path. It is in version *25*, and it is reviewed by many reviewers, like CK and Angelo. The reset.h is also reviewed by Krzysztof. This series is also well tested by Rex-BC and Angelo. Rex tested this series with modetest successfully using 5.19-rc2 mainline kernel with dp/dpintf/dp phy series.([1]) Could you kindly take a look for this series and give us some comments or feedback? We really need this series being accepted. Thanks for your big support! [1]: https://patchwork.kernel.org/project/linux-mediatek/list/?series=654074 https://patchwork.kernel.org/project/linux-mediatek/list/?series=653448 https://patchwork.kernel.org/project/linux-mediatek/list/?series=653410 BRs, Nancy
On Mon, 2022-07-11 at 15:52 +0800, Nancy.Lin wrote: > The hardware path of vdosys1 with DPTx output need to go through by > several modules, such as, OVL_ADAPTOR and MERGE. > > Add mmsys and mutex modules support by the patches below: > > Changes in v25: > - fix reviewer comment > - refine mtk_mmsys_reset_update func > - rebase to next-20220708 > > Changes in v24: > - fix reviewer comment > - refine mtk_mmsys_reset_update func > - rebase to next-20220622 > > Changes in v23: > - separate[7] mmsys/mutex and drm patches into two series > > Changes in v22: > - rebase to next-20220525 > - rebase to vdosys0 series v22 > - separate dts to a new patch > > Changes in v21: > - fix reviewer comment > - fix rdma and ethdr binding doc and dts > > Changes in v20: > - fix reviewer comment > - update mmsys update bit api name > - add mtk_mmsys_update_bits error message if lose gce property > - list all mt8195 vdosys1 reset bits > > Changes in v19: > - fix reviewer comment > - separate mt8195 mmsys component to a new patch > - separate mt8195 vdo0 and vdo1 routing table > - separate mmsys_write_reg api to a new patch and simplify write > reg code > - separate mmsys 64 bit reset to a new patch > - separate mtk-mutex dp_intf1 component to a new patch > > Changes in v18: > - fix reviewer comment > - fix rdma binding doc > - fix ethdr binding doc > - refine mmsys config cmdq support > - refine merge reset control flow, get reset control in probe > function > - add ethdr reset control error handling and remove dbg log > - rebase to vdosys0 series v20 (ref [5]) > > Changes in v17: > - fix reviewer comment in v16 > - separate ovl adaptor comp in mtk-mmsys and mtk-mutex > - separate mmsys config API > - move mdp_rdma binding yaml > - fix ovl adaptor pm runtime get sync timing issue > - rebase to vdosys0 series v19 (ref [5]) > - rebase to [7] for modify vblank register change > > Changes in v16: > - fix reviewer comment in v 15 > - fix mtk_drm_ddp_comp.c alignment > - fix vdosys0 mmsys num before adding vdosys1 patch > > Changes in v15: > - fix ethdr uppercase hex number in dts > > Changes in v14: > - remove MTK_MMSYS 64 bit dependency > - add ethdr.yaml back and fix dt_schema check fail > > Resend v13 > - add related maintainer in maillist > > Changes in v13: > - fix reviewer comment in v12 > - fix rdma dt-binding format > - fix dts node naming > - fix 32 bit build error > - modify 64bit dependency for mtk-mmsys > - rebase to vdosys0 series v16. (ref [5]) > > Changes in v12: > - fix reviewer comment in v11 > - modify mbox index > - refine dma dev for ovl_adaptor sub driver > > Changes in v11: > - remove ethdr vblank spin lock > - refine ovl_adaptor print message > > Changes in v10: > - refine ethdr reset control using > devm_reset_control_array_get_optional_exclusive > - fix ovl_adaptor mtk_ovl_adaptor_clk_enable error handle issue > > Changes in v9: > - rebase on kernel-5.16-rc1 > - rebase on vdosys0 series v13. (ref [5]) > - fix ovl_adaptor sub driver is brought up unintentionally > - fix clang build test fail- duplicate ethdr/mdp_rdma > init_module/cleanup_module symbol issue > > Changes in v8: > - separate merge async reset to new patch. > - separate drm ovl_adaptor sub driver to new patch. > - fix reviewer comment in v7. > > Changes in v7: > - rebase on vdosys0 series v12 (ref[5]) > - add dma description in ethdr binding document. > - refine vdosys1 bit definition of mmsys routing table. > - separate merge modification into 3 pathces. > - separate mutex modification into 2 patches. > - add plane color coding for mdp_rdma csc. > - move mdp_rdma pm control to ovl_adaptor. > - fix reviewer comment in v6. > > Changes in v6: > - rebase on kernel-5.15-rc1. > - change mbox label to gce0 for dts node of vdosys1. > - modify mmsys reset num for mt8195. > - rebase on vdosys0 series v10. (ref [5]) > - use drm to bring up ovl_adaptor driver. > - move drm iommu/mutex check from kms init to drm bind. > - modify rdma binding doc location. > (Documentation/devicetree/bindings/arm/) > - modify for reviewer's comment in v5. > > Changes in v5: > - add mmsys reset controller reference. > > Changes in v4: > - use merge common driver for merge1~4. > - refine ovl_adaptor rdma driver. > - use ovl_adaptor ddp_comp function instead of ethdr. > - modify for reviewer's comment in v3. > > Changes in v3: > - modify for reviewer's comment in v2. > - add vdosys1 2 pixels align limit. > - add mixer odd offset support. > > Changes in v2: > - Merge PSEUDO_OVL and ETHDR into one DRM component. > - Add mmsys config API for vdosys1 hardware setting. > - Add mmsys reset control using linux reset framework. > > Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com> > > This series are based on the following patch: > [1] arm64: dts: Add mediatek SoC mt8195 and evaluation board > 20220112114724.1953-4-tinghan.shen@mediatek.com > [2] arm64: dts: mt8195: add IOMMU and smi nodes > 20210615173233.26682-15-tinghan.shen@mediatek.com > [3] arm64: dts: mt8195: add gce node > 20220126090109.32143-1-jason-jh.lin@mediatek.com > [4] [v2] arm64: dts: mt8195: add display node for vdosys0 > 20220225021535.2655-1-jason-jh.lin@mediatek.com > [5] Add MediaTek SoC DRM (vdosys0) support for mt8195 - v22 series > 20220526102126.19756-1-jason-jh.lin@mediatek.com > [6] dt-bindings: mediatek: mt8195: Add binding for MM IOMMU > 20220407075726.17771-2-yong.wu@mediatek.com > [7] Add MediaTek SoC DRM (vdosys1) support for mt8195 > 20220526110233.20080-1-nancy.lin@mediatek.com > > Nancy.Lin (10): > dt-bindings: reset: mt8195: add vdosys1 reset control bit > soc: mediatek: add mtk-mmsys ethdr and mdp_rdma components > soc: mediatek: add mtk-mmsys support for mt8195 vdosys1 > soc: mediatek: add mtk_mmsys_update_bits API > soc: mediatek: add mtk-mmsys config API for mt8195 vdosys1 > soc: mediatek: add cmdq support of mtk-mmsys config API for mt8195 > vdosys1 > soc: mediatek: mmsys: add mmsys for support 64 reset bits > soc: mediatek: mmsys: add reset control for MT8195 vdosys1 > soc: mediatek: add mtk-mutex component - dp_intf1 > soc: mediatek: add mtk-mutex support for mt8195 vdosys1 > > drivers/soc/mediatek/mt8195-mmsys.h | 146 > ++++++++++++++++++++++ > drivers/soc/mediatek/mtk-mmsys.c | 132 ++++++++++++++----- > drivers/soc/mediatek/mtk-mmsys.h | 1 + > drivers/soc/mediatek/mtk-mutex.c | 37 ++++++ > include/dt-bindings/reset/mt8195-resets.h | 45 +++++++ > include/linux/soc/mediatek/mtk-mmsys.h | 25 ++++ > 6 files changed, 355 insertions(+), 31 deletions(-) Hello Matthias, Because Kernel 6.0-rc1 is released, I re-test this series. I use dp series [1] to test this mmsys series because this series is used to control external display. In my test, I can do modtest of these mode for DP and it passed. Whole series again for 6.0-rc1: Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> #0 1920x1080 60.00 1920 2008 2052 2200 1080 1084 1089 1125 148500 flags: phsync, pvsync; type: preferred, driver #1 1920x1080 59.94 1920 2008 2052 2200 1080 1084 1089 1125 148352 flags: phsync, pvsync; type: driver #2 1920x1080 50.00 1920 2448 2492 2640 1080 1084 1089 1125 148500 flags: phsync, pvsync; type: driver #3 1680x1050 59.95 1680 1784 1960 2240 1050 1053 1059 1089 146250 flags: nhsync, pvsync; type: driver #4 1600x900 60.00 1600 1624 1704 1800 900 901 904 1000 108000 flags: phsync, pvsync; type: driver #5 1280x1024 60.02 1280 1328 1440 1688 1024 1025 1028 1066 108000 flags: phsync, pvsync; type: driver #6 1280x800 59.81 1280 1352 1480 1680 800 803 809 831 83500 flags: nhsync, pvsync; type: driver #7 1280x720 60.00 1280 1390 1430 1650 720 725 730 750 74250 flags: phsync, pvsync; type: driver #8 1280x720 59.94 1280 1390 1430 1650 720 725 730 750 74176 flags: phsync, pvsync; type: driver #9 1280x720 50.00 1280 1720 1760 1980 720 725 730 750 74250 flags: phsync, pvsync; type: driver #10 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 flags: nhsync, nvsync; type: driver #11 800x600 60.32 800 840 968 1056 600 601 605 628 40000 flags: phsync, pvsync; type: driver #12 720x576 50.00 720 732 796 864 576 581 586 625 27000 flags: nhsync, nvsync; type: driver #13 720x480 60.00 720 736 798 858 480 489 495 525 27027 flags: nhsync, nvsync; type: driver #14 720x480 59.94 720 736 798 858 480 489 495 525 27000 flags: nhsync, nvsync; type: driver #15 640x480 60.00 640 656 752 800 480 490 492 525 25200 flags: nhsync, nvsync; type: driver #16 640x480 59.94 640 656 752 800 480 490 492 525 25175 flags: nhsync, nvsync; type: driver [1]: https://patchwork.kernel.org/project/linux-mediatek/list/?series=665597 BRs, Bo-Chen
On Fri, Aug 05, 2022 at 06:04:08PM +0800, Nancy.Lin wrote: [..] > Hello Matthias, > > This series is about mmsys configuration of external display path. > > It is in version *25*, and it is reviewed by many reviewers, like CK > and Angelo. > The reset.h is also reviewed by Krzysztof. > > This series is also well tested by Rex-BC and Angelo. There is actually a silly but breaking bug in this version [1] affecting a lot of platforms, including mt8192. I'll provide a Tested-by tag for mt8192 in the next version, just in case. (If you can, please CC me, Nancy). Thanks, Nícolas [1] https://lore.kernel.org/all/20220818214715.spbyic34szubx3gi@notapiano/
The hardware path of vdosys1 with DPTx output need to go through by several modules, such as, OVL_ADAPTOR and MERGE. Add mmsys and mutex modules support by the patches below: Changes in v25: - fix reviewer comment - refine mtk_mmsys_reset_update func - rebase to next-20220708 Changes in v24: - fix reviewer comment - refine mtk_mmsys_reset_update func - rebase to next-20220622 Changes in v23: - separate[7] mmsys/mutex and drm patches into two series Changes in v22: - rebase to next-20220525 - rebase to vdosys0 series v22 - separate dts to a new patch Changes in v21: - fix reviewer comment - fix rdma and ethdr binding doc and dts Changes in v20: - fix reviewer comment - update mmsys update bit api name - add mtk_mmsys_update_bits error message if lose gce property - list all mt8195 vdosys1 reset bits Changes in v19: - fix reviewer comment - separate mt8195 mmsys component to a new patch - separate mt8195 vdo0 and vdo1 routing table - separate mmsys_write_reg api to a new patch and simplify write reg code - separate mmsys 64 bit reset to a new patch - separate mtk-mutex dp_intf1 component to a new patch Changes in v18: - fix reviewer comment - fix rdma binding doc - fix ethdr binding doc - refine mmsys config cmdq support - refine merge reset control flow, get reset control in probe function - add ethdr reset control error handling and remove dbg log - rebase to vdosys0 series v20 (ref [5]) Changes in v17: - fix reviewer comment in v16 - separate ovl adaptor comp in mtk-mmsys and mtk-mutex - separate mmsys config API - move mdp_rdma binding yaml - fix ovl adaptor pm runtime get sync timing issue - rebase to vdosys0 series v19 (ref [5]) - rebase to [7] for modify vblank register change Changes in v16: - fix reviewer comment in v 15 - fix mtk_drm_ddp_comp.c alignment - fix vdosys0 mmsys num before adding vdosys1 patch Changes in v15: - fix ethdr uppercase hex number in dts Changes in v14: - remove MTK_MMSYS 64 bit dependency - add ethdr.yaml back and fix dt_schema check fail Resend v13 - add related maintainer in maillist Changes in v13: - fix reviewer comment in v12 - fix rdma dt-binding format - fix dts node naming - fix 32 bit build error - modify 64bit dependency for mtk-mmsys - rebase to vdosys0 series v16. (ref [5]) Changes in v12: - fix reviewer comment in v11 - modify mbox index - refine dma dev for ovl_adaptor sub driver Changes in v11: - remove ethdr vblank spin lock - refine ovl_adaptor print message Changes in v10: - refine ethdr reset control using devm_reset_control_array_get_optional_exclusive - fix ovl_adaptor mtk_ovl_adaptor_clk_enable error handle issue Changes in v9: - rebase on kernel-5.16-rc1 - rebase on vdosys0 series v13. (ref [5]) - fix ovl_adaptor sub driver is brought up unintentionally - fix clang build test fail- duplicate ethdr/mdp_rdma init_module/cleanup_module symbol issue Changes in v8: - separate merge async reset to new patch. - separate drm ovl_adaptor sub driver to new patch. - fix reviewer comment in v7. Changes in v7: - rebase on vdosys0 series v12 (ref[5]) - add dma description in ethdr binding document. - refine vdosys1 bit definition of mmsys routing table. - separate merge modification into 3 pathces. - separate mutex modification into 2 patches. - add plane color coding for mdp_rdma csc. - move mdp_rdma pm control to ovl_adaptor. - fix reviewer comment in v6. Changes in v6: - rebase on kernel-5.15-rc1. - change mbox label to gce0 for dts node of vdosys1. - modify mmsys reset num for mt8195. - rebase on vdosys0 series v10. (ref [5]) - use drm to bring up ovl_adaptor driver. - move drm iommu/mutex check from kms init to drm bind. - modify rdma binding doc location. (Documentation/devicetree/bindings/arm/) - modify for reviewer's comment in v5. Changes in v5: - add mmsys reset controller reference. Changes in v4: - use merge common driver for merge1~4. - refine ovl_adaptor rdma driver. - use ovl_adaptor ddp_comp function instead of ethdr. - modify for reviewer's comment in v3. Changes in v3: - modify for reviewer's comment in v2. - add vdosys1 2 pixels align limit. - add mixer odd offset support. Changes in v2: - Merge PSEUDO_OVL and ETHDR into one DRM component. - Add mmsys config API for vdosys1 hardware setting. - Add mmsys reset control using linux reset framework. Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com> This series are based on the following patch: [1] arm64: dts: Add mediatek SoC mt8195 and evaluation board 20220112114724.1953-4-tinghan.shen@mediatek.com [2] arm64: dts: mt8195: add IOMMU and smi nodes 20210615173233.26682-15-tinghan.shen@mediatek.com [3] arm64: dts: mt8195: add gce node 20220126090109.32143-1-jason-jh.lin@mediatek.com [4] [v2] arm64: dts: mt8195: add display node for vdosys0 20220225021535.2655-1-jason-jh.lin@mediatek.com [5] Add MediaTek SoC DRM (vdosys0) support for mt8195 - v22 series 20220526102126.19756-1-jason-jh.lin@mediatek.com [6] dt-bindings: mediatek: mt8195: Add binding for MM IOMMU 20220407075726.17771-2-yong.wu@mediatek.com [7] Add MediaTek SoC DRM (vdosys1) support for mt8195 20220526110233.20080-1-nancy.lin@mediatek.com Nancy.Lin (10): dt-bindings: reset: mt8195: add vdosys1 reset control bit soc: mediatek: add mtk-mmsys ethdr and mdp_rdma components soc: mediatek: add mtk-mmsys support for mt8195 vdosys1 soc: mediatek: add mtk_mmsys_update_bits API soc: mediatek: add mtk-mmsys config API for mt8195 vdosys1 soc: mediatek: add cmdq support of mtk-mmsys config API for mt8195 vdosys1 soc: mediatek: mmsys: add mmsys for support 64 reset bits soc: mediatek: mmsys: add reset control for MT8195 vdosys1 soc: mediatek: add mtk-mutex component - dp_intf1 soc: mediatek: add mtk-mutex support for mt8195 vdosys1 drivers/soc/mediatek/mt8195-mmsys.h | 146 ++++++++++++++++++++++ drivers/soc/mediatek/mtk-mmsys.c | 132 ++++++++++++++----- drivers/soc/mediatek/mtk-mmsys.h | 1 + drivers/soc/mediatek/mtk-mutex.c | 37 ++++++ include/dt-bindings/reset/mt8195-resets.h | 45 +++++++ include/linux/soc/mediatek/mtk-mmsys.h | 25 ++++ 6 files changed, 355 insertions(+), 31 deletions(-)