diff mbox

[2/3] thermal: Add Mediatek thermal controller support

Message ID 1447835066-10482-3-git-send-email-s.hauer@pengutronix.de (mailing list archive)
State New, archived
Headers show

Commit Message

Sascha Hauer Nov. 18, 2015, 8:24 a.m. UTC
This adds support for the Mediatek thermal controller found on MT8173
and likely other SoCs.
The controller is a bit special. It does not have its own ADC, instead
it controls the on-SoC AUXADC via AHB bus accesses. For this reason
we need the physical address of the AUXADC. Also it controls a mux
using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 drivers/thermal/Kconfig       |   8 +
 drivers/thermal/Makefile      |   1 +
 drivers/thermal/mtk_thermal.c | 623 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 632 insertions(+)
 create mode 100644 drivers/thermal/mtk_thermal.c

Comments

Dawei Chien Nov. 24, 2015, 6:06 a.m. UTC | #1
Hi Sascha,

On Wed, 2015-11-18 at 09:24 +0100, Sascha Hauer wrote:
> This adds support for the Mediatek thermal controller found on MT8173
> and likely other SoCs.
> The controller is a bit special. It does not have its own ADC, instead
> it controls the on-SoC AUXADC via AHB bus accesses. For this reason
> we need the physical address of the AUXADC. Also it controls a mux
> using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.
> 
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
>  drivers/thermal/Kconfig       |   8 +
>  drivers/thermal/Makefile      |   1 +
>  drivers/thermal/mtk_thermal.c | 623 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 632 insertions(+)
>  create mode 100644 drivers/thermal/mtk_thermal.c
> 
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 5aabc4b..503448a 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -348,6 +348,14 @@ config INTEL_PCH_THERMAL
>  	  Thermal reporting device will provide temperature reading,
>  	  programmable trip points and other information.
>  
> +config MTK_THERMAL
> +	tristate "Temperature sensor driver for mediatek SoCs"Why does ret value didn't set to 0 during this function. This function of return value would be not 0 with valid calibration data.
> +	depends on ARCH_MEDIATEK || COMPILE_TEST
> +	default y
> +	help
> +	  Enable this option if you want to have support for thermal management
> +	  controller present in Mediatek SoCs
> +
>  menu "Texas Instruments thermal drivers"
>  depends on ARCH_HAS_BANDGAP || COMPILE_TEST
>  source "drivers/thermal/ti-soc-thermal/Kconfig"
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 26f1608..5f979e7 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -45,3 +45,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL)	+= intel_pch_thermal.o
>  obj-$(CONFIG_ST_THERMAL)	+= st/
>  obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
>  obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
> +obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> new file mode 100644
> index 0000000..0bdf38d
> --- /dev/null
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -0,0 +1,623 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Hanyi Wu <hanyi.wu@mediatek.com>
> + *         Sascha Hauer <s.hauer@pengutronix.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/io.h>
> +#include <linux/thermal.h>
> +#include <linux/reset.h>
> +#include <linux/types.h>
> +#include <linux/nvmem-consumer.h>
> +
> +/* AUXADC Registers */
> +#define AUXADC_CON0_V		0x000
> +#define AUXADC_CON1_V		0x004
> +#define AUXADC_CON1_SET_V	0x008
> +#define AUXADC_CON1_CLR_V	0x00c
> +#define AUXADC_CON2_V		0x010
> +#define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
> +#define AUXADC_MISC_V		0x094
> +
> +#define AUXADC_CON1_CHANNEL(x)	BIT(x)
> +
> +#define APMIXED_SYS_TS_CON1	0x604
> +
> +/* Thermal Controller Registers */
> +#define TEMP_MONCTL0		0x000
> +#define TEMP_MONCTL1		0x004
> +#define TEMP_MONCTL2		0x008
> +#define TEMP_MONIDET0		0x014
> +#define TEMP_MONIDET1		0x018
> +#define TEMP_MSRCTL0		0x038
> +#define TEMP_AHBPOLL		0x040
> +#define TEMP_AHBTO		0x044
> +#define TEMP_ADCPNP0		0x048
> +#define TEMP_ADCPNP1		0x04c
> +#define TEMP_ADCPNP2		0x050
> +#define TEMP_ADCPNP3		0x0b4
> +
> +#define TEMP_ADCMUX		0x054
> +#define TEMP_ADCEN		0x060
> +#define TEMP_PNPMUXADDR		0x064
> +#define TEMP_ADCMUXADDR		0x068
> +#define TEMP_ADCENADDR		0x074
> +#define TEMP_ADCVALIDADDR	0x078
> +#define TEMP_ADCVOLTADDR	0x07c
> +#define TEMP_RDCTRL		0x080
> +#define TEMP_ADCVALIDMASK	0x084
> +#define TEMP_ADCVOLTAGESHIFT	0x088
> +#define TEMP_ADCWRITECTRL	0x08c
> +#define TEMP_MSR0		0x090Hi Sascha,
> +#define TEMP_MSR1		0x094
> +#define TEMP_MSR2		0x098
> +#define TEMP_MSR3		0x0B8
> +
> +#define TEMP_SPARE0		0x0f0
> +
> +#define PTPCORESEL		0x400
> +
> +#define TEMP_MONCTL1_PERIOD_UNIT(x)	((x) & 0x3ff)
> +
> +#define TEMP_MONCTL2_FILTER_INTERVAL(x)	(((x) & 0x3ff)) << 16
> +#define TEMP_MONCTL2_SENSOR_INTERVAL(x)	((x) & 0x3ff)
> +
> +#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x)	(x)
> +
> +#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE		BIT(0)
> +#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE		BIT(1)
> +
> +#define TEMP_ADCVALIDMASK_VALID_HIGH		BIT(5)
> +#define TEMP_ADCVALIDMASK_VALID_POS(bit)	(bit)
> +
> +#define MT8173_TS1	0
> +#define MT8173_TS2	1
> +#define MT8173_TS3	2
> +#define MT8173_TS4	3
> +#define MT8173_TSABB	4
> +
> +/* AUXADC channel 11 is used for the temperature sensors */
> +#define MT8173_TEMP_AUXADC_CHANNEL	11
> +
> +/* The total number of temperature sensors in the MT8173 */
> +#define MT8173_NUM_SENSORS		5
> +
> +/* The number of banks in the MT8173 */
> +#define MT8173_NUM_ZONES		4
> +
> +/* The number of sensing points per bank */
> +#define MT8173_NUM_SENSORS_PER_ZONE	4
> +
> +/* Layout of the fuses providing the calibration data */
> +#define MT8173_CALIB_BUF0_VALID		(1 << 0)
> +#define MT8173_CALIB_BUF1_ADC_GE(x)	(((x) >> 22 ) & 0x3ff)
> +#define MT8173_CALIB_BUF0_VTS_TS1(x)	(((x) >> 17 ) & 0x1ff)
> +#define MT8173_CALIB_BUF0_VTS_TS2(x)	(((x) >> 8 ) & 0x1ff)
> +#define MT8173_CALIB_BUF1_VTS_TS3(x)	(((x) >> 0 ) & 0x1ff)
> +#define MT8173_CALIB_BUF2_VTS_TS4(x)	(((x) >> 23 ) & 0x1ff)
> +#define MT8173_CALIB_BUF2_VTS_TSABB(x)	(((x) >> 14 ) & 0x1ff)
> +#define MT8173_CALIB_BUF0_DEGC_CALI(x)	(((x) >> 1 ) & 0x3f)
> +#define MT8173_CALIB_BUF0_O_SLOPE(x)	(((x) >> 26 ) & 0x3f)
> +
> +#define THERMAL_NAME    "mtk-thermal"
> +
> +struct mtk_thermal;
> +
> +struct mtk_thermal_bank {
> +	struct mtk_thermal *mt;
> +	int id;
> +};
> +
> +struct mtk_thermal {
> +	struct device *dev;
> +	void __iomem *thermal_base;
> +
> +	struct clk *clk_peri_therm;
> +	struct clk *clk_auxadc;
> +
> +	struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
> +
> +	struct mutex lock;
> +
> +	/* Calibration values */
> +	s32 adc_ge;
> +	s32 degc_cali;
> +	s32 o_slope;
> +	s32 vts[MT8173_NUM_SENSORS];
> +
> +	struct thermal_zone_device *tzd;
> +};
> +
> +struct mtk_thermal_bank_cfg {
> +	unsigned int num_sensors;
> +	unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
> +};
> +
> +static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
> +
> +/*
> + * The MT8173 thermal controller has four banks. Each bank can read up to
> + * four temperature sensors simultaneously. The MT8173 has a total of 5
> + * temperature sensors. We use each bank to measure a certain area of the
> + * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
> + * areas, hence is used in different banks.
> + *
> + * The thermal core only gets the maximum temperature of all banks, so
> + * the bank concept wouldn't be necessary here. However, the SVS (Smart
> + * Voltage Scaling) unit makes its decisions based on the same bank
> + * data, and this indeed needs the temperatures of the individual banks
> + * for making better decisions.
> + */
> +static const struct mtk_thermal_bank_cfg bank_data[] = {
> +	{
> +		.num_sensors = 2,
> +		.sensors = { MT8173_TS2, MT8173_TS3 },
> +	}, {
> +		.num_sensors = 2,
> +		.sensors = { MT8173_TS2, MT8173_TS4 },
> +	}, {
> +		.num_sensors = 3,
> +		.sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
> +	}, {
> +		.num_sensors = 1,
> +		.sensors = { MT8173_TS2 },
> +	},
> +};
> +
> +struct mtk_thermal_sense_point {
> +	int msr;
> +	int adcpnp;
> +};
> +
> +static const struct mtk_thermal_sense_point
> +		sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
> +	{
> +		.msr = TEMP_MSR0,
> +		.adcpnp = TEMP_ADCPNP0,
> +	}, {
> +		.msr = TEMP_MSR1,
> +		.adcpnp = TEMP_ADCPNP1,
> +	}, {
> +		.msr = TEMP_MSR2,
> +		.adcpnp = TEMP_ADCPNP2,
> +	}, {
> +		.msr = TEMP_MSR3,
> +		.adcpnp = TEMP_ADCPNP3,
> +	},
> +};
> +
> +/**
> + * raw_to_mcelsius - convert a raw ADC value to mcelsius
> + * @mt:		The thermal controller
> + * @raw:	raw ADC value
> + *
> + * This converts the raw ADC value to mcelsius using the SoC specific
> + * calibration constants
> + */
> +static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
> +{
> +	s32 tmp;
> +
> +	raw &= 0xfff;
> +
> +	tmp = 203450520 << 3;
> +	tmp /= 165 + mt->o_slope;
> +	tmp /= 10000 + mt->adc_ge;
> +	tmp *= raw - mt->vts[sensno] - 3350;
> +	tmp >>= 3;
> +
> +	return mt->degc_cali * 500 - tmp;
> +}
> +
> +/**
> + * mtk_thermal_get_bank - get bank
> + * @bank:	The bank
> + *
> + * The bank registers are banked, we have to select a bank in the
> + * PTPCORESEL register to access it.
> + */
> +static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
> +{
> +	struct mtk_thermal *mt = bank->mt;
> +	u32 val;
> +
> +	mutex_lock(&mt->lock);
> +
> +	val = readl(mt->thermal_base + PTPCORESEL);
> +	val &= ~0xf;
> +	val |= bank->id;
> +	writel(val, mt->thermal_base + PTPCORESEL);
> +}
> +
> +/**
> + * mtk_thermal_put_bank - release bank
> + * @bank:	The bank
> + *
> + * release a bank previously taken with mtk_thermal_get_bank,
> + */
> +static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
> +{
> +	struct mtk_thermal *mt = bank->mt;
> +
> +	mutex_unlock(&mt->lock);
> +}
> +
> +/**
> + * mtk_thermal_bank_temperature - get the temperature of a bank
> + * @bank:	The bank
> + *
> + * The temperature of a bank is considered the maximum temperature of
> + * the sensors associated to the bank.
> + */
> +static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> +{
> +	struct mtk_thermal *mt = bank->mt;
> +	int temp, i, max;
> +	u32 raw;
> +
> +	temp = max = INT_MIN;
> +
> +	for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
> +		raw = readl(mt->thermal_base + sensing_points[i].msr);
> +
> +		temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw);
> +
> +		/*
> +		 * The first read of a sensor often contains very high bogus
> +		 * temperature value. Filter these out so that the system does
> +		 * not immediately shut down.
> +		 */
> +		if (temp > 200000)
> +			temp = 0;
> +
> +		if (temp > max)
> +			max = temp;
> +	}
> +
> +	return max;
> +}
> +
> +static int mtk_read_temp(void *data, int *temperature)
> +{
> +	struct mtk_thermal *mt = data;
> +	int i;
> +	int tempmax = INT_MIN;
> +
> +	for (i = 0; i < MT8173_NUM_ZONES; i++) {
> +		struct mtk_thermal_bank *bank = &mt->banks[i];
> +
> +		mtk_thermal_get_bank(bank);
> +
> +		tempmax = max(tempmax, mtk_thermal_bank_temperature(bank));
> +
> +		mtk_thermal_put_bank(bank);
> +	}
> +
> +	*temperature = tempmax;
> +
> +	return 0;
> +}
> +
> +static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
> +	.get_temp = mtk_read_temp,
> +};
> +
> +static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> +		u32 apmixed_phys_base, u32 auxadc_phys_base)
> +{
> +	struct mtk_thermal_bank *bank = &mt->banks[num];
> +	const struct mtk_thermal_bank_cfg *cfg = &bank_data[num];
> +	int i;
> +
> +	bank->id = num;
> +	bank->mt = mt;
> +
> +	mtk_thermal_get_bank(bank);
> +
> +	/* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
> +	writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
> +
> +	/*
> +	 * filt interval is 1 * 46.540us = 46.54us,
> +	 * sen interval is 429 * 46.540us = 19.96ms
> +	 */
> +	writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
> +			TEMP_MONCTL2_SENSOR_INTERVAL(429),
> +			mt->thermal_base + TEMP_MONCTL2);
> +
> +	/* poll is set to 10u */
> +	writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
> +			mt->thermal_base + TEMP_AHBPOLL);
> +
> +	/* temperature sampling control, 1 sample */
> +	writel(0x0, mt->thermal_base + TEMP_MSRCTL0);
> +
> +	/* exceed this polling time, IRQ would be inserted */
> +	writel(0xffffffff, mt->thermal_base + TEMP_AHBTO);
> +
> +	/* number of interrupts per event, 1 is enough */
> +	writel(0x0, mt->thermal_base + TEMP_MONIDET0);
> +	writel(0x0, mt->thermal_base + TEMP_MONIDET1);
> +
> +	/*
> +	 * The MT8173 thermal controller does not have its own ADC. Instead it
> +	 * uses AHB bus accesses to control the AUXADC. To do this the thermal
> +	 * controller has to be programmed with the physical addresses of the
> +	 * AUXADC registers and with the various bit positions in the AUXADC.
> +	 * Also the thermal controller controls a mux in the APMIXEDSYS register
> +	 * space.
> +	 */
> +
> +	/*
> +	 * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
> +	 * automatically by hw
> +	 */
> +	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX);
> +
> +	/* AHB address for auxadc mux selection */
> +	writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
> +			mt->thermal_base + TEMP_ADCMUXADDR);
> +
> +	/* AHB address for pnp sensor mux selection */
> +	writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> +			mt->thermal_base + TEMP_PNPMUXADDR);
> +
> +	/* AHB value for auxadc enable */
> +	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN);
> +
> +	/* AHB address for auxadc enable (channel 0 immediate mode selected) */
> +	writel(auxadc_phys_base + AUXADC_CON1_SET_V,
> +			mt->thermal_base + TEMP_ADCENADDR);
> +
> +	/* AHB address for auxadc valid bit */
> +	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
> +			mt->thermal_base + TEMP_ADCVALIDADDR);
> +
> +	/* AHB address for auxadc voltage output */
> +	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
> +			mt->thermal_base + TEMP_ADCVOLTADDR);
> +
> +	/* read valid & voltage are at the same register */
> +	writel(0x0, mt->thermal_base + TEMP_RDCTRL);
> +
> +	/* indicate where the valid bit is */
> +	writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
> +			mt->thermal_base + TEMP_ADCVALIDMASK);
> +
> +	/* no shift */
> +	writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT);
> +
> +	/* enable auxadc mux write transaction */
> +	writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
> +			mt->thermal_base + TEMP_ADCWRITECTRL);
> +
> +	for (i = 0; i < cfg->num_sensors; i++)
> +		writel(sensor_mux_values[cfg->sensors[i]],
> +				mt->thermal_base + sensing_points[i].adcpnp);
> +
> +	writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0);
> +
> +	writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE | TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
> +			mt->thermal_base + TEMP_ADCWRITECTRL);
> +
> +	mtk_thermal_put_bank(bank);
> +}
> +
> +static u64 of_get_phys_base(struct device_node *np)
> +{
> +	u64 size64;
> +	const __be32 *regaddr_p;
> +
> +	regaddr_p = of_get_address(np, 0, &size64, NULL);
> +	if (!regaddr_p)
> +		return OF_BAD_ADDR;
> +
> +	return of_translate_address(np, regaddr_p);
> +}
> +
> +static int mtk_thermal_get_calibration_data(struct device *dev, struct mtk_thermal *mt)
> +{
> +	struct nvmem_cell *cell;
> +	u32 *buf;
> +	size_t len;
> +	int i, ret;
> +	/* Start with default values */
> +	mt->adc_ge = 512;
> +	for (i = 0; i < MT8173_NUM_SENSORS; i++)
> +		mt->vts[i] = 260;
> +	mt->degc_cali = 40;
> +	mt->o_slope = 0;
> +
> +	cell = nvmem_cell_get(dev, "calibration-data");
> +	if (IS_ERR(cell)) {
> +		if (PTR_ERR(cell) == -EPROBE_DEFER)
> +			return PTR_ERR(cell);
> +		return 0;
> +	}
> +
> +	buf = (u32 *)nvmem_cell_read(cell, &len);
> +
> +	nvmem_cell_put(cell);
> +
> +	if (IS_ERR(buf))
> +		return PTR_ERR(buf);
> +
> +	if (len < 3 * sizeof(u32)) {
> +		dev_warn(dev, "invalid calibration data\n");
> +		ret = -EINVAL;
> +		goto out;
> +	}

ret would not be assigned if the length of calibration data is correct.
Otherwise,
Tested-by: Dawei Chien <dawei.chien@mediatek.com>
Thanks.

> +	if (buf[0] & MT8173_CALIB_BUF0_VALID) {
> +		mt->adc_ge = MT8173_CALIB_BUF1_ADC_GE(buf[1]);
> +		mt->vts[MT8173_TS1] = MT8173_CALIB_BUF0_VTS_TS1(buf[0]);
> +		mt->vts[MT8173_TS2] = MT8173_CALIB_BUF0_VTS_TS2(buf[0]);
> +		mt->vts[MT8173_TS3] = MT8173_CALIB_BUF1_VTS_TS3(buf[1]);
> +		mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]);
> +		mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]);
> +		mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]);
> +		mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
> +	} else {
> +		dev_info(dev, "Device not calibrated, using default calibration values\n");
> +	}
> +
> +out:
> +	kfree(buf);
> +
> +	return ret;
> +}
> +
> +static int mtk_thermal_probe(struct platform_device *pdev)
> +{
> +	int ret, i;
> +	struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
> +	struct mtk_thermal *mt;
> +	struct resource *res;
> +	u64 auxadc_phys_base, apmixed_phys_base;
> +
> +	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
> +	if (!mt)
> +		return -ENOMEM;
> +
> +	mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
> +	if (IS_ERR(mt->clk_peri_therm))
> +		return PTR_ERR(mt->clk_peri_therm);
> +
> +	mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc");
> +	if (IS_ERR(mt->clk_auxadc))
> +		return PTR_ERR(mt->clk_auxadc);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	mt->thermal_base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(mt->thermal_base))
> +		return PTR_ERR(mt->thermal_base);
> +
> +	ret = mtk_thermal_get_calibration_data(&pdev->dev, mt);
> +	if (ret)
> +		return ret;
> +
> +	mutex_init(&mt->lock);
> +
> +	mt->dev = &pdev->dev;
> +
> +	auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
> +	if (!auxadc) {
> +		dev_err(&pdev->dev, "missing auxadc node\n");
> +		return -ENODEV;
> +	}
> +
> +	auxadc_phys_base = of_get_phys_base(auxadc);
> +
> +	of_node_put(auxadc);
> +
> +	if (auxadc_phys_base == OF_BAD_ADDR) {
> +		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
> +		return -EINVAL;
> +	}
> +
> +	apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
> +	if (!apmixedsys) {
> +		dev_err(&pdev->dev, "missing apmixedsys node\n");
> +		return -ENODEV;
> +	}
> +
> +	apmixed_phys_base = of_get_phys_base(apmixedsys);
> +
> +	of_node_put(apmixedsys);
> +
> +	if (apmixed_phys_base == OF_BAD_ADDR) {
> +		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = clk_prepare_enable(mt->clk_auxadc);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = device_reset(&pdev->dev);
> +	if (ret)
> +		goto err_disable_clk_auxadc;
> +
> +	ret = clk_prepare_enable(mt->clk_peri_therm);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
> +		goto err_disable_clk_auxadc;
> +	}
> +
> +	for (i = 0; i < MT8173_NUM_ZONES; i++)
> +		mtk_thermal_init_bank(mt, i, apmixed_phys_base, auxadc_phys_base);
> +
> +	platform_set_drvdata(pdev, mt);
> +
> +	mt->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
> +				&mtk_thermal_ops);
> +	if (IS_ERR(mt->tzd))
> +		goto err_register;
> +
> +	return 0;
> +
> +err_register:
> +	clk_disable_unprepare(mt->clk_peri_therm);
> +
> +err_disable_clk_auxadc:
> +	clk_disable_unprepare(mt->clk_auxadc);
> +
> +	return ret;
> +}
> +
> +static int mtk_thermal_remove(struct platform_device *pdev)
> +{
> +	struct mtk_thermal *mt = platform_get_drvdata(pdev);
> +
> +	thermal_zone_of_sensor_unregister(&pdev->dev, mt->tzd);
> +
> +	clk_disable_unprepare(mt->clk_peri_therm);
> +	clk_disable_unprepare(mt->clk_auxadc);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id mtk_thermal_of_match[] = {
> +	{
> +		.compatible = "mediatek,mt8173-thermal",
> +	}, {
> +	},
> +};
> +
> +static struct platform_driver mtk_thermal_driver = {
> +	.probe = mtk_thermal_probe,
> +	.remove = mtk_thermal_remove,
> +	.driver = {
> +		.name = THERMAL_NAME,
> +		.of_match_table = mtk_thermal_of_match,
> +	},
> +};
> +
> +module_platform_driver(mtk_thermal_driver);
> +
> +MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de");
> +MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>");
> +MODULE_DESCRIPTION("Mediatek thermal driver");
> +MODULE_LICENSE("GPL v2");
Sascha Hauer Nov. 24, 2015, 7:53 a.m. UTC | #2
On Tue, Nov 24, 2015 at 02:06:09PM +0800, dawei chien wrote:
> Hi Sascha,
> 
> > +static int mtk_thermal_get_calibration_data(struct device *dev, struct mtk_thermal *mt)
> > +{
> > +	struct nvmem_cell *cell;
> > +	u32 *buf;
> > +	size_t len;
> > +	int i, ret;
> > +	/* Start with default values */
> > +	mt->adc_ge = 512;
> > +	for (i = 0; i < MT8173_NUM_SENSORS; i++)
> > +		mt->vts[i] = 260;
> > +	mt->degc_cali = 40;
> > +	mt->o_slope = 0;
> > +
> > +	cell = nvmem_cell_get(dev, "calibration-data");
> > +	if (IS_ERR(cell)) {
> > +		if (PTR_ERR(cell) == -EPROBE_DEFER)
> > +			return PTR_ERR(cell);
> > +		return 0;
> > +	}
> > +
> > +	buf = (u32 *)nvmem_cell_read(cell, &len);
> > +
> > +	nvmem_cell_put(cell);
> > +
> > +	if (IS_ERR(buf))
> > +		return PTR_ERR(buf);
> > +
> > +	if (len < 3 * sizeof(u32)) {
> > +		dev_warn(dev, "invalid calibration data\n");
> > +		ret = -EINVAL;
> > +		goto out;
> > +	}
> 
> ret would not be assigned if the length of calibration data is correct.
> Otherwise,

gcc does a increasingly bad job when it comes to warn about
uninitialized variables :(

Sascha
diff mbox

Patch

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 5aabc4b..503448a 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -348,6 +348,14 @@  config INTEL_PCH_THERMAL
 	  Thermal reporting device will provide temperature reading,
 	  programmable trip points and other information.
 
+config MTK_THERMAL
+	tristate "Temperature sensor driver for mediatek SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	default y
+	help
+	  Enable this option if you want to have support for thermal management
+	  controller present in Mediatek SoCs
+
 menu "Texas Instruments thermal drivers"
 depends on ARCH_HAS_BANDGAP || COMPILE_TEST
 source "drivers/thermal/ti-soc-thermal/Kconfig"
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 26f1608..5f979e7 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -45,3 +45,4 @@  obj-$(CONFIG_INTEL_PCH_THERMAL)	+= intel_pch_thermal.o
 obj-$(CONFIG_ST_THERMAL)	+= st/
 obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
 obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
+obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
new file mode 100644
index 0000000..0bdf38d
--- /dev/null
+++ b/drivers/thermal/mtk_thermal.c
@@ -0,0 +1,623 @@ 
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Hanyi Wu <hanyi.wu@mediatek.com>
+ *         Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/thermal.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+#include <linux/nvmem-consumer.h>
+
+/* AUXADC Registers */
+#define AUXADC_CON0_V		0x000
+#define AUXADC_CON1_V		0x004
+#define AUXADC_CON1_SET_V	0x008
+#define AUXADC_CON1_CLR_V	0x00c
+#define AUXADC_CON2_V		0x010
+#define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
+#define AUXADC_MISC_V		0x094
+
+#define AUXADC_CON1_CHANNEL(x)	BIT(x)
+
+#define APMIXED_SYS_TS_CON1	0x604
+
+/* Thermal Controller Registers */
+#define TEMP_MONCTL0		0x000
+#define TEMP_MONCTL1		0x004
+#define TEMP_MONCTL2		0x008
+#define TEMP_MONIDET0		0x014
+#define TEMP_MONIDET1		0x018
+#define TEMP_MSRCTL0		0x038
+#define TEMP_AHBPOLL		0x040
+#define TEMP_AHBTO		0x044
+#define TEMP_ADCPNP0		0x048
+#define TEMP_ADCPNP1		0x04c
+#define TEMP_ADCPNP2		0x050
+#define TEMP_ADCPNP3		0x0b4
+
+#define TEMP_ADCMUX		0x054
+#define TEMP_ADCEN		0x060
+#define TEMP_PNPMUXADDR		0x064
+#define TEMP_ADCMUXADDR		0x068
+#define TEMP_ADCENADDR		0x074
+#define TEMP_ADCVALIDADDR	0x078
+#define TEMP_ADCVOLTADDR	0x07c
+#define TEMP_RDCTRL		0x080
+#define TEMP_ADCVALIDMASK	0x084
+#define TEMP_ADCVOLTAGESHIFT	0x088
+#define TEMP_ADCWRITECTRL	0x08c
+#define TEMP_MSR0		0x090
+#define TEMP_MSR1		0x094
+#define TEMP_MSR2		0x098
+#define TEMP_MSR3		0x0B8
+
+#define TEMP_SPARE0		0x0f0
+
+#define PTPCORESEL		0x400
+
+#define TEMP_MONCTL1_PERIOD_UNIT(x)	((x) & 0x3ff)
+
+#define TEMP_MONCTL2_FILTER_INTERVAL(x)	(((x) & 0x3ff)) << 16
+#define TEMP_MONCTL2_SENSOR_INTERVAL(x)	((x) & 0x3ff)
+
+#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x)	(x)
+
+#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE		BIT(0)
+#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE		BIT(1)
+
+#define TEMP_ADCVALIDMASK_VALID_HIGH		BIT(5)
+#define TEMP_ADCVALIDMASK_VALID_POS(bit)	(bit)
+
+#define MT8173_TS1	0
+#define MT8173_TS2	1
+#define MT8173_TS3	2
+#define MT8173_TS4	3
+#define MT8173_TSABB	4
+
+/* AUXADC channel 11 is used for the temperature sensors */
+#define MT8173_TEMP_AUXADC_CHANNEL	11
+
+/* The total number of temperature sensors in the MT8173 */
+#define MT8173_NUM_SENSORS		5
+
+/* The number of banks in the MT8173 */
+#define MT8173_NUM_ZONES		4
+
+/* The number of sensing points per bank */
+#define MT8173_NUM_SENSORS_PER_ZONE	4
+
+/* Layout of the fuses providing the calibration data */
+#define MT8173_CALIB_BUF0_VALID		(1 << 0)
+#define MT8173_CALIB_BUF1_ADC_GE(x)	(((x) >> 22 ) & 0x3ff)
+#define MT8173_CALIB_BUF0_VTS_TS1(x)	(((x) >> 17 ) & 0x1ff)
+#define MT8173_CALIB_BUF0_VTS_TS2(x)	(((x) >> 8 ) & 0x1ff)
+#define MT8173_CALIB_BUF1_VTS_TS3(x)	(((x) >> 0 ) & 0x1ff)
+#define MT8173_CALIB_BUF2_VTS_TS4(x)	(((x) >> 23 ) & 0x1ff)
+#define MT8173_CALIB_BUF2_VTS_TSABB(x)	(((x) >> 14 ) & 0x1ff)
+#define MT8173_CALIB_BUF0_DEGC_CALI(x)	(((x) >> 1 ) & 0x3f)
+#define MT8173_CALIB_BUF0_O_SLOPE(x)	(((x) >> 26 ) & 0x3f)
+
+#define THERMAL_NAME    "mtk-thermal"
+
+struct mtk_thermal;
+
+struct mtk_thermal_bank {
+	struct mtk_thermal *mt;
+	int id;
+};
+
+struct mtk_thermal {
+	struct device *dev;
+	void __iomem *thermal_base;
+
+	struct clk *clk_peri_therm;
+	struct clk *clk_auxadc;
+
+	struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
+
+	struct mutex lock;
+
+	/* Calibration values */
+	s32 adc_ge;
+	s32 degc_cali;
+	s32 o_slope;
+	s32 vts[MT8173_NUM_SENSORS];
+
+	struct thermal_zone_device *tzd;
+};
+
+struct mtk_thermal_bank_cfg {
+	unsigned int num_sensors;
+	unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
+};
+
+static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
+
+/*
+ * The MT8173 thermal controller has four banks. Each bank can read up to
+ * four temperature sensors simultaneously. The MT8173 has a total of 5
+ * temperature sensors. We use each bank to measure a certain area of the
+ * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
+ * areas, hence is used in different banks.
+ *
+ * The thermal core only gets the maximum temperature of all banks, so
+ * the bank concept wouldn't be necessary here. However, the SVS (Smart
+ * Voltage Scaling) unit makes its decisions based on the same bank
+ * data, and this indeed needs the temperatures of the individual banks
+ * for making better decisions.
+ */
+static const struct mtk_thermal_bank_cfg bank_data[] = {
+	{
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS3 },
+	}, {
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS4 },
+	}, {
+		.num_sensors = 3,
+		.sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
+	}, {
+		.num_sensors = 1,
+		.sensors = { MT8173_TS2 },
+	},
+};
+
+struct mtk_thermal_sense_point {
+	int msr;
+	int adcpnp;
+};
+
+static const struct mtk_thermal_sense_point
+		sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
+	{
+		.msr = TEMP_MSR0,
+		.adcpnp = TEMP_ADCPNP0,
+	}, {
+		.msr = TEMP_MSR1,
+		.adcpnp = TEMP_ADCPNP1,
+	}, {
+		.msr = TEMP_MSR2,
+		.adcpnp = TEMP_ADCPNP2,
+	}, {
+		.msr = TEMP_MSR3,
+		.adcpnp = TEMP_ADCPNP3,
+	},
+};
+
+/**
+ * raw_to_mcelsius - convert a raw ADC value to mcelsius
+ * @mt:		The thermal controller
+ * @raw:	raw ADC value
+ *
+ * This converts the raw ADC value to mcelsius using the SoC specific
+ * calibration constants
+ */
+static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
+{
+	s32 tmp;
+
+	raw &= 0xfff;
+
+	tmp = 203450520 << 3;
+	tmp /= 165 + mt->o_slope;
+	tmp /= 10000 + mt->adc_ge;
+	tmp *= raw - mt->vts[sensno] - 3350;
+	tmp >>= 3;
+
+	return mt->degc_cali * 500 - tmp;
+}
+
+/**
+ * mtk_thermal_get_bank - get bank
+ * @bank:	The bank
+ *
+ * The bank registers are banked, we have to select a bank in the
+ * PTPCORESEL register to access it.
+ */
+static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	u32 val;
+
+	mutex_lock(&mt->lock);
+
+	val = readl(mt->thermal_base + PTPCORESEL);
+	val &= ~0xf;
+	val |= bank->id;
+	writel(val, mt->thermal_base + PTPCORESEL);
+}
+
+/**
+ * mtk_thermal_put_bank - release bank
+ * @bank:	The bank
+ *
+ * release a bank previously taken with mtk_thermal_get_bank,
+ */
+static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+
+	mutex_unlock(&mt->lock);
+}
+
+/**
+ * mtk_thermal_bank_temperature - get the temperature of a bank
+ * @bank:	The bank
+ *
+ * The temperature of a bank is considered the maximum temperature of
+ * the sensors associated to the bank.
+ */
+static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	int temp, i, max;
+	u32 raw;
+
+	temp = max = INT_MIN;
+
+	for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
+		raw = readl(mt->thermal_base + sensing_points[i].msr);
+
+		temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw);
+
+		/*
+		 * The first read of a sensor often contains very high bogus
+		 * temperature value. Filter these out so that the system does
+		 * not immediately shut down.
+		 */
+		if (temp > 200000)
+			temp = 0;
+
+		if (temp > max)
+			max = temp;
+	}
+
+	return max;
+}
+
+static int mtk_read_temp(void *data, int *temperature)
+{
+	struct mtk_thermal *mt = data;
+	int i;
+	int tempmax = INT_MIN;
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++) {
+		struct mtk_thermal_bank *bank = &mt->banks[i];
+
+		mtk_thermal_get_bank(bank);
+
+		tempmax = max(tempmax, mtk_thermal_bank_temperature(bank));
+
+		mtk_thermal_put_bank(bank);
+	}
+
+	*temperature = tempmax;
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
+	.get_temp = mtk_read_temp,
+};
+
+static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
+		u32 apmixed_phys_base, u32 auxadc_phys_base)
+{
+	struct mtk_thermal_bank *bank = &mt->banks[num];
+	const struct mtk_thermal_bank_cfg *cfg = &bank_data[num];
+	int i;
+
+	bank->id = num;
+	bank->mt = mt;
+
+	mtk_thermal_get_bank(bank);
+
+	/* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
+	writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
+
+	/*
+	 * filt interval is 1 * 46.540us = 46.54us,
+	 * sen interval is 429 * 46.540us = 19.96ms
+	 */
+	writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
+			TEMP_MONCTL2_SENSOR_INTERVAL(429),
+			mt->thermal_base + TEMP_MONCTL2);
+
+	/* poll is set to 10u */
+	writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
+			mt->thermal_base + TEMP_AHBPOLL);
+
+	/* temperature sampling control, 1 sample */
+	writel(0x0, mt->thermal_base + TEMP_MSRCTL0);
+
+	/* exceed this polling time, IRQ would be inserted */
+	writel(0xffffffff, mt->thermal_base + TEMP_AHBTO);
+
+	/* number of interrupts per event, 1 is enough */
+	writel(0x0, mt->thermal_base + TEMP_MONIDET0);
+	writel(0x0, mt->thermal_base + TEMP_MONIDET1);
+
+	/*
+	 * The MT8173 thermal controller does not have its own ADC. Instead it
+	 * uses AHB bus accesses to control the AUXADC. To do this the thermal
+	 * controller has to be programmed with the physical addresses of the
+	 * AUXADC registers and with the various bit positions in the AUXADC.
+	 * Also the thermal controller controls a mux in the APMIXEDSYS register
+	 * space.
+	 */
+
+	/*
+	 * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
+	 * automatically by hw
+	 */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX);
+
+	/* AHB address for auxadc mux selection */
+	writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
+			mt->thermal_base + TEMP_ADCMUXADDR);
+
+	/* AHB address for pnp sensor mux selection */
+	writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
+			mt->thermal_base + TEMP_PNPMUXADDR);
+
+	/* AHB value for auxadc enable */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN);
+
+	/* AHB address for auxadc enable (channel 0 immediate mode selected) */
+	writel(auxadc_phys_base + AUXADC_CON1_SET_V,
+			mt->thermal_base + TEMP_ADCENADDR);
+
+	/* AHB address for auxadc valid bit */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+			mt->thermal_base + TEMP_ADCVALIDADDR);
+
+	/* AHB address for auxadc voltage output */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+			mt->thermal_base + TEMP_ADCVOLTADDR);
+
+	/* read valid & voltage are at the same register */
+	writel(0x0, mt->thermal_base + TEMP_RDCTRL);
+
+	/* indicate where the valid bit is */
+	writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
+			mt->thermal_base + TEMP_ADCVALIDMASK);
+
+	/* no shift */
+	writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT);
+
+	/* enable auxadc mux write transaction */
+	writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+			mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	for (i = 0; i < cfg->num_sensors; i++)
+		writel(sensor_mux_values[cfg->sensors[i]],
+				mt->thermal_base + sensing_points[i].adcpnp);
+
+	writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0);
+
+	writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE | TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+			mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	mtk_thermal_put_bank(bank);
+}
+
+static u64 of_get_phys_base(struct device_node *np)
+{
+	u64 size64;
+	const __be32 *regaddr_p;
+
+	regaddr_p = of_get_address(np, 0, &size64, NULL);
+	if (!regaddr_p)
+		return OF_BAD_ADDR;
+
+	return of_translate_address(np, regaddr_p);
+}
+
+static int mtk_thermal_get_calibration_data(struct device *dev, struct mtk_thermal *mt)
+{
+	struct nvmem_cell *cell;
+	u32 *buf;
+	size_t len;
+	int i, ret;
+
+	/* Start with default values */
+	mt->adc_ge = 512;
+	for (i = 0; i < MT8173_NUM_SENSORS; i++)
+		mt->vts[i] = 260;
+	mt->degc_cali = 40;
+	mt->o_slope = 0;
+
+	cell = nvmem_cell_get(dev, "calibration-data");
+	if (IS_ERR(cell)) {
+		if (PTR_ERR(cell) == -EPROBE_DEFER)
+			return PTR_ERR(cell);
+		return 0;
+	}
+
+	buf = (u32 *)nvmem_cell_read(cell, &len);
+
+	nvmem_cell_put(cell);
+
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	if (len < 3 * sizeof(u32)) {
+		dev_warn(dev, "invalid calibration data\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (buf[0] & MT8173_CALIB_BUF0_VALID) {
+		mt->adc_ge = MT8173_CALIB_BUF1_ADC_GE(buf[1]);
+		mt->vts[MT8173_TS1] = MT8173_CALIB_BUF0_VTS_TS1(buf[0]);
+		mt->vts[MT8173_TS2] = MT8173_CALIB_BUF0_VTS_TS2(buf[0]);
+		mt->vts[MT8173_TS3] = MT8173_CALIB_BUF1_VTS_TS3(buf[1]);
+		mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]);
+		mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]);
+		mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]);
+		mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
+	} else {
+		dev_info(dev, "Device not calibrated, using default calibration values\n");
+	}
+
+out:
+	kfree(buf);
+
+	return ret;
+}
+
+static int mtk_thermal_probe(struct platform_device *pdev)
+{
+	int ret, i;
+	struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
+	struct mtk_thermal *mt;
+	struct resource *res;
+	u64 auxadc_phys_base, apmixed_phys_base;
+
+	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
+	if (!mt)
+		return -ENOMEM;
+
+	mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
+	if (IS_ERR(mt->clk_peri_therm))
+		return PTR_ERR(mt->clk_peri_therm);
+
+	mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc");
+	if (IS_ERR(mt->clk_auxadc))
+		return PTR_ERR(mt->clk_auxadc);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mt->thermal_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mt->thermal_base))
+		return PTR_ERR(mt->thermal_base);
+
+	ret = mtk_thermal_get_calibration_data(&pdev->dev, mt);
+	if (ret)
+		return ret;
+
+	mutex_init(&mt->lock);
+
+	mt->dev = &pdev->dev;
+
+	auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
+	if (!auxadc) {
+		dev_err(&pdev->dev, "missing auxadc node\n");
+		return -ENODEV;
+	}
+
+	auxadc_phys_base = of_get_phys_base(auxadc);
+
+	of_node_put(auxadc);
+
+	if (auxadc_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
+	if (!apmixedsys) {
+		dev_err(&pdev->dev, "missing apmixedsys node\n");
+		return -ENODEV;
+	}
+
+	apmixed_phys_base = of_get_phys_base(apmixedsys);
+
+	of_node_put(apmixedsys);
+
+	if (apmixed_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	ret = clk_prepare_enable(mt->clk_auxadc);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
+		return ret;
+	}
+
+	ret = device_reset(&pdev->dev);
+	if (ret)
+		goto err_disable_clk_auxadc;
+
+	ret = clk_prepare_enable(mt->clk_peri_therm);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
+		goto err_disable_clk_auxadc;
+	}
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++)
+		mtk_thermal_init_bank(mt, i, apmixed_phys_base, auxadc_phys_base);
+
+	platform_set_drvdata(pdev, mt);
+
+	mt->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
+				&mtk_thermal_ops);
+	if (IS_ERR(mt->tzd))
+		goto err_register;
+
+	return 0;
+
+err_register:
+	clk_disable_unprepare(mt->clk_peri_therm);
+
+err_disable_clk_auxadc:
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return ret;
+}
+
+static int mtk_thermal_remove(struct platform_device *pdev)
+{
+	struct mtk_thermal *mt = platform_get_drvdata(pdev);
+
+	thermal_zone_of_sensor_unregister(&pdev->dev, mt->tzd);
+
+	clk_disable_unprepare(mt->clk_peri_therm);
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return 0;
+}
+
+static const struct of_device_id mtk_thermal_of_match[] = {
+	{
+		.compatible = "mediatek,mt8173-thermal",
+	}, {
+	},
+};
+
+static struct platform_driver mtk_thermal_driver = {
+	.probe = mtk_thermal_probe,
+	.remove = mtk_thermal_remove,
+	.driver = {
+		.name = THERMAL_NAME,
+		.of_match_table = mtk_thermal_of_match,
+	},
+};
+
+module_platform_driver(mtk_thermal_driver);
+
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de");
+MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>");
+MODULE_DESCRIPTION("Mediatek thermal driver");
+MODULE_LICENSE("GPL v2");