@@ -41,6 +41,8 @@
#define U3P_USBPHYACR0 0x000
#define PA0_RG_U2PLL_FORCE_ON BIT(15)
+#define PA0_USB20_PLL_PREDIV GENMASK(7, 6)
+#define PA0_USB20_PLL_PREDIV_VAL(x) ((0x3 & (x)) << 6)
#define PA0_RG_USB20_INTR_EN BIT(5)
#define U3P_USBPHYACR1 0x004
@@ -52,6 +54,8 @@
#define PA1_RG_TERM_SEL_VAL(x) ((0x7 & (x)) << 8)
#define U3P_USBPHYACR2 0x008
+#define PA2_RG_U2PLL_BW GENMASK(21, 19)
+#define PA2_RG_U2PLL_BW_VAL(x) ((0x7 & (x)) << 19)
#define PA2_RG_SIF_U2PLL_FORCE_EN BIT(18)
#define U3P_USBPHYACR5 0x014
@@ -73,6 +77,14 @@
#define P2C_USB20_GPIO_MODE BIT(8)
#define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+#define U3P_U2PHYA_RESV 0x030
+#define P2R_RG_U2PLL_FBDIV_26M 0x1bb13b
+#define P2R_RG_U2PLL_FBDIV_48M 0x3c0000
+
+#define U3P_U2PHYA_RESV1 0x044
+#define P2R_RG_U2PLL_REFCLK_SEL BIT(5)
+#define P2R_RG_U2PLL_FRA_EN BIT(3)
+
#define U3D_U2PHYDCR0 0x060
#define P2C_RG_SIF_U2PLL_FORCE_ON BIT(24)
@@ -277,6 +289,12 @@ enum mtk_phy_version {
struct mtk_phy_pdata {
/* avoid RX sensitivity level degradation only for mt8173 */
bool avoid_rx_sen_degradation;
+ /*
+ * u2phy should use integer mode instead of fractional mode of
+ * 48M PLL, fix it by switching PLL to 26M from default 48M
+ * for mt8195
+ */
+ bool sw_pll_48m_to_26m;
enum mtk_phy_version version;
};
@@ -456,6 +474,33 @@ static void u3_phy_instance_init(struct mtk_tphy *tphy,
dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
}
+static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
+ struct mtk_phy_instance *instance)
+{
+ struct u2phy_banks *u2_banks = &instance->u2_banks;
+ void __iomem *com = u2_banks->com;
+ u32 tmp;
+
+ if (!tphy->pdata->sw_pll_48m_to_26m)
+ return;
+
+ tmp = readl(com + U3P_USBPHYACR0);
+ tmp &= ~PA0_USB20_PLL_PREDIV;
+ tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
+ writel(tmp, com + U3P_USBPHYACR0);
+
+ tmp = readl(com + U3P_USBPHYACR2);
+ tmp &= ~PA2_RG_U2PLL_BW;
+ tmp |= PA2_RG_U2PLL_BW_VAL(3);
+ writel(tmp, com + U3P_USBPHYACR2);
+
+ writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
+
+ tmp = readl(com + U3P_U2PHYA_RESV1);
+ tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
+ writel(tmp, com + U3P_U2PHYA_RESV1);
+}
+
static void u2_phy_instance_init(struct mtk_tphy *tphy,
struct mtk_phy_instance *instance)
{
@@ -941,6 +986,7 @@ static int mtk_phy_init(struct phy *phy)
switch (instance->type) {
case PHY_TYPE_USB2:
+ u2_phy_pll_26m_set(tphy, instance);
u2_phy_instance_init(tphy, instance);
u2_phy_props_set(tphy, instance);
break;
@@ -1094,10 +1140,16 @@ static const struct mtk_phy_pdata mt8173_pdata = {
.version = MTK_PHY_V1,
};
+static const struct mtk_phy_pdata mt8195_pdata = {
+ .sw_pll_48m_to_26m = true,
+ .version = MTK_PHY_V3,
+};
+
static const struct of_device_id mtk_tphy_id_table[] = {
{ .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
+ { .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
{ .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
The controller is designed to use use PLL integer mode, but in fact used fractional mode for some ones on mt8195, this causes signal degradation (e.g. eye diagram test fail), fix it by switching PLL to 26Mhz from default 48Mhz to improve signal quality. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)