Message ID | 20180125001639.14681-2-martin.blumenstingl@googlemail.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Hi, On Thu, 2018-01-25 at 01:16 +0100, Martin Blumenstingl wrote: > The new PHY wrapper is now wired up in the core HCD code. This means > that PHYs are now controlled (initialized, enabled, disabled, exited) > without requiring any host-driver specific code. > Remove the custom USB PHY handling from the mtu3 driver as the core HCD > code now handles this. > > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> > --- > drivers/usb/mtu3/mtu3_plat.c | 101 ------------------------------------------- > 1 file changed, 101 deletions(-) > > diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c > index 628d5ce356ca..a894ddf25bcd 100644 > --- a/drivers/usb/mtu3/mtu3_plat.c > +++ b/drivers/usb/mtu3/mtu3_plat.c > @@ -44,62 +44,6 @@ int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks) > return 0; > } > > -static int ssusb_phy_init(struct ssusb_mtk *ssusb) > -{ > - int i; > - int ret; > - > - for (i = 0; i < ssusb->num_phys; i++) { > - ret = phy_init(ssusb->phys[i]); > - if (ret) > - goto exit_phy; > - } > - return 0; > - > -exit_phy: > - for (; i > 0; i--) > - phy_exit(ssusb->phys[i - 1]); > - > - return ret; > -} > - > -static int ssusb_phy_exit(struct ssusb_mtk *ssusb) > -{ > - int i; > - > - for (i = 0; i < ssusb->num_phys; i++) > - phy_exit(ssusb->phys[i]); > - > - return 0; > -} > - > -static int ssusb_phy_power_on(struct ssusb_mtk *ssusb) > -{ > - int i; > - int ret; > - > - for (i = 0; i < ssusb->num_phys; i++) { > - ret = phy_power_on(ssusb->phys[i]); > - if (ret) > - goto power_off_phy; > - } > - return 0; > - > -power_off_phy: > - for (; i > 0; i--) > - phy_power_off(ssusb->phys[i - 1]); > - > - return ret; > -} > - > -static void ssusb_phy_power_off(struct ssusb_mtk *ssusb) > -{ > - unsigned int i; > - > - for (i = 0; i < ssusb->num_phys; i++) > - phy_power_off(ssusb->phys[i]); > -} > - > static int ssusb_clks_enable(struct ssusb_mtk *ssusb) > { > int ret; > @@ -162,24 +106,8 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb) > if (ret) > goto clks_err; > > - ret = ssusb_phy_init(ssusb); > - if (ret) { > - dev_err(ssusb->dev, "failed to init phy\n"); > - goto phy_init_err; > - } > - > - ret = ssusb_phy_power_on(ssusb); > - if (ret) { > - dev_err(ssusb->dev, "failed to power on phy\n"); > - goto phy_err; > - } > - > return 0; > > -phy_err: > - ssusb_phy_exit(ssusb); > -phy_init_err: > - ssusb_clks_disable(ssusb); > clks_err: > regulator_disable(ssusb->vusb33); > vusb33_err: > @@ -190,8 +118,6 @@ static void ssusb_rscs_exit(struct ssusb_mtk *ssusb) > { > ssusb_clks_disable(ssusb); > regulator_disable(ssusb->vusb33); > - ssusb_phy_power_off(ssusb); > - ssusb_phy_exit(ssusb); > } > > static void ssusb_ip_sw_reset(struct ssusb_mtk *ssusb) > @@ -222,7 +148,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) > struct device *dev = &pdev->dev; > struct regulator *vbus; > struct resource *res; > - int i; > int ret; > > ssusb->vusb33 = devm_regulator_get(&pdev->dev, "vusb33"); > @@ -249,25 +174,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) > if (IS_ERR(ssusb->dma_clk)) > return PTR_ERR(ssusb->dma_clk); > > - ssusb->num_phys = of_count_phandle_with_args(node, > - "phys", "#phy-cells"); > - if (ssusb->num_phys > 0) { > - ssusb->phys = devm_kcalloc(dev, ssusb->num_phys, > - sizeof(*ssusb->phys), GFP_KERNEL); > - if (!ssusb->phys) > - return -ENOMEM; > - } else { > - ssusb->num_phys = 0; > - } > - > - for (i = 0; i < ssusb->num_phys; i++) { > - ssusb->phys[i] = devm_of_phy_get_by_index(dev, node, i); > - if (IS_ERR(ssusb->phys[i])) { > - dev_err(dev, "failed to get phy-%d\n", i); > - return PTR_ERR(ssusb->phys[i]); > - } > - } > - > res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc"); > ssusb->ippc_base = devm_ioremap_resource(dev, res); > if (IS_ERR(ssusb->ippc_base)) > @@ -457,7 +363,6 @@ static int __maybe_unused mtu3_suspend(struct device *dev) > return 0; > > ssusb_host_disable(ssusb, true); > - ssusb_phy_power_off(ssusb); > ssusb_clks_disable(ssusb); > ssusb_wakeup_set(ssusb, true); > > @@ -480,16 +385,10 @@ static int __maybe_unused mtu3_resume(struct device *dev) > if (ret) > goto clks_err; > > - ret = ssusb_phy_power_on(ssusb); > - if (ret) > - goto phy_err; > - > ssusb_host_enable(ssusb); > > return 0; > > -phy_err: > - ssusb_clks_disable(ssusb); > clks_err: > return ret; > } This patch will affect device function when works as device only mode. Please abandon it, and I will modify it if need after the patch series of "initialize (multiple) PHYs for a HCD" are picked up. Thanks a lot
Hi, On Thu, Jan 25, 2018 at 3:47 AM, Chunfeng Yun <chunfeng.yun@mediatek.com> wrote: > Hi, > > On Thu, 2018-01-25 at 01:16 +0100, Martin Blumenstingl wrote: >> The new PHY wrapper is now wired up in the core HCD code. This means >> that PHYs are now controlled (initialized, enabled, disabled, exited) >> without requiring any host-driver specific code. >> Remove the custom USB PHY handling from the mtu3 driver as the core HCD >> code now handles this. >> >> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> >> --- >> drivers/usb/mtu3/mtu3_plat.c | 101 ------------------------------------------- >> 1 file changed, 101 deletions(-) >> >> diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c >> index 628d5ce356ca..a894ddf25bcd 100644 >> --- a/drivers/usb/mtu3/mtu3_plat.c >> +++ b/drivers/usb/mtu3/mtu3_plat.c >> @@ -44,62 +44,6 @@ int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks) >> return 0; >> } >> >> -static int ssusb_phy_init(struct ssusb_mtk *ssusb) >> -{ >> - int i; >> - int ret; >> - >> - for (i = 0; i < ssusb->num_phys; i++) { >> - ret = phy_init(ssusb->phys[i]); >> - if (ret) >> - goto exit_phy; >> - } >> - return 0; >> - >> -exit_phy: >> - for (; i > 0; i--) >> - phy_exit(ssusb->phys[i - 1]); >> - >> - return ret; >> -} >> - >> -static int ssusb_phy_exit(struct ssusb_mtk *ssusb) >> -{ >> - int i; >> - >> - for (i = 0; i < ssusb->num_phys; i++) >> - phy_exit(ssusb->phys[i]); >> - >> - return 0; >> -} >> - >> -static int ssusb_phy_power_on(struct ssusb_mtk *ssusb) >> -{ >> - int i; >> - int ret; >> - >> - for (i = 0; i < ssusb->num_phys; i++) { >> - ret = phy_power_on(ssusb->phys[i]); >> - if (ret) >> - goto power_off_phy; >> - } >> - return 0; >> - >> -power_off_phy: >> - for (; i > 0; i--) >> - phy_power_off(ssusb->phys[i - 1]); >> - >> - return ret; >> -} >> - >> -static void ssusb_phy_power_off(struct ssusb_mtk *ssusb) >> -{ >> - unsigned int i; >> - >> - for (i = 0; i < ssusb->num_phys; i++) >> - phy_power_off(ssusb->phys[i]); >> -} >> - >> static int ssusb_clks_enable(struct ssusb_mtk *ssusb) >> { >> int ret; >> @@ -162,24 +106,8 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb) >> if (ret) >> goto clks_err; >> >> - ret = ssusb_phy_init(ssusb); >> - if (ret) { >> - dev_err(ssusb->dev, "failed to init phy\n"); >> - goto phy_init_err; >> - } >> - >> - ret = ssusb_phy_power_on(ssusb); >> - if (ret) { >> - dev_err(ssusb->dev, "failed to power on phy\n"); >> - goto phy_err; >> - } >> - >> return 0; >> >> -phy_err: >> - ssusb_phy_exit(ssusb); >> -phy_init_err: >> - ssusb_clks_disable(ssusb); >> clks_err: >> regulator_disable(ssusb->vusb33); >> vusb33_err: >> @@ -190,8 +118,6 @@ static void ssusb_rscs_exit(struct ssusb_mtk *ssusb) >> { >> ssusb_clks_disable(ssusb); >> regulator_disable(ssusb->vusb33); >> - ssusb_phy_power_off(ssusb); >> - ssusb_phy_exit(ssusb); >> } >> >> static void ssusb_ip_sw_reset(struct ssusb_mtk *ssusb) >> @@ -222,7 +148,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) >> struct device *dev = &pdev->dev; >> struct regulator *vbus; >> struct resource *res; >> - int i; >> int ret; >> >> ssusb->vusb33 = devm_regulator_get(&pdev->dev, "vusb33"); >> @@ -249,25 +174,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) >> if (IS_ERR(ssusb->dma_clk)) >> return PTR_ERR(ssusb->dma_clk); >> >> - ssusb->num_phys = of_count_phandle_with_args(node, >> - "phys", "#phy-cells"); >> - if (ssusb->num_phys > 0) { >> - ssusb->phys = devm_kcalloc(dev, ssusb->num_phys, >> - sizeof(*ssusb->phys), GFP_KERNEL); >> - if (!ssusb->phys) >> - return -ENOMEM; >> - } else { >> - ssusb->num_phys = 0; >> - } >> - >> - for (i = 0; i < ssusb->num_phys; i++) { >> - ssusb->phys[i] = devm_of_phy_get_by_index(dev, node, i); >> - if (IS_ERR(ssusb->phys[i])) { >> - dev_err(dev, "failed to get phy-%d\n", i); >> - return PTR_ERR(ssusb->phys[i]); >> - } >> - } >> - >> res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc"); >> ssusb->ippc_base = devm_ioremap_resource(dev, res); >> if (IS_ERR(ssusb->ippc_base)) >> @@ -457,7 +363,6 @@ static int __maybe_unused mtu3_suspend(struct device *dev) >> return 0; >> >> ssusb_host_disable(ssusb, true); >> - ssusb_phy_power_off(ssusb); >> ssusb_clks_disable(ssusb); >> ssusb_wakeup_set(ssusb, true); >> >> @@ -480,16 +385,10 @@ static int __maybe_unused mtu3_resume(struct device *dev) >> if (ret) >> goto clks_err; >> >> - ret = ssusb_phy_power_on(ssusb); >> - if (ret) >> - goto phy_err; >> - >> ssusb_host_enable(ssusb); >> >> return 0; >> >> -phy_err: >> - ssusb_clks_disable(ssusb); >> clks_err: >> return ret; >> } > This patch will affect device function when works as device only mode. > Please abandon it, and I will modify it if need after the patch series > of "initialize (multiple) PHYs for a HCD" are picked up. thank you for reviewing this it seems that I indeed missed the device only mode functionality I'll drop the patch from my next version and let you handle this (thank you in advance)! Regards Martin
diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c index 628d5ce356ca..a894ddf25bcd 100644 --- a/drivers/usb/mtu3/mtu3_plat.c +++ b/drivers/usb/mtu3/mtu3_plat.c @@ -44,62 +44,6 @@ int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks) return 0; } -static int ssusb_phy_init(struct ssusb_mtk *ssusb) -{ - int i; - int ret; - - for (i = 0; i < ssusb->num_phys; i++) { - ret = phy_init(ssusb->phys[i]); - if (ret) - goto exit_phy; - } - return 0; - -exit_phy: - for (; i > 0; i--) - phy_exit(ssusb->phys[i - 1]); - - return ret; -} - -static int ssusb_phy_exit(struct ssusb_mtk *ssusb) -{ - int i; - - for (i = 0; i < ssusb->num_phys; i++) - phy_exit(ssusb->phys[i]); - - return 0; -} - -static int ssusb_phy_power_on(struct ssusb_mtk *ssusb) -{ - int i; - int ret; - - for (i = 0; i < ssusb->num_phys; i++) { - ret = phy_power_on(ssusb->phys[i]); - if (ret) - goto power_off_phy; - } - return 0; - -power_off_phy: - for (; i > 0; i--) - phy_power_off(ssusb->phys[i - 1]); - - return ret; -} - -static void ssusb_phy_power_off(struct ssusb_mtk *ssusb) -{ - unsigned int i; - - for (i = 0; i < ssusb->num_phys; i++) - phy_power_off(ssusb->phys[i]); -} - static int ssusb_clks_enable(struct ssusb_mtk *ssusb) { int ret; @@ -162,24 +106,8 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb) if (ret) goto clks_err; - ret = ssusb_phy_init(ssusb); - if (ret) { - dev_err(ssusb->dev, "failed to init phy\n"); - goto phy_init_err; - } - - ret = ssusb_phy_power_on(ssusb); - if (ret) { - dev_err(ssusb->dev, "failed to power on phy\n"); - goto phy_err; - } - return 0; -phy_err: - ssusb_phy_exit(ssusb); -phy_init_err: - ssusb_clks_disable(ssusb); clks_err: regulator_disable(ssusb->vusb33); vusb33_err: @@ -190,8 +118,6 @@ static void ssusb_rscs_exit(struct ssusb_mtk *ssusb) { ssusb_clks_disable(ssusb); regulator_disable(ssusb->vusb33); - ssusb_phy_power_off(ssusb); - ssusb_phy_exit(ssusb); } static void ssusb_ip_sw_reset(struct ssusb_mtk *ssusb) @@ -222,7 +148,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) struct device *dev = &pdev->dev; struct regulator *vbus; struct resource *res; - int i; int ret; ssusb->vusb33 = devm_regulator_get(&pdev->dev, "vusb33"); @@ -249,25 +174,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb) if (IS_ERR(ssusb->dma_clk)) return PTR_ERR(ssusb->dma_clk); - ssusb->num_phys = of_count_phandle_with_args(node, - "phys", "#phy-cells"); - if (ssusb->num_phys > 0) { - ssusb->phys = devm_kcalloc(dev, ssusb->num_phys, - sizeof(*ssusb->phys), GFP_KERNEL); - if (!ssusb->phys) - return -ENOMEM; - } else { - ssusb->num_phys = 0; - } - - for (i = 0; i < ssusb->num_phys; i++) { - ssusb->phys[i] = devm_of_phy_get_by_index(dev, node, i); - if (IS_ERR(ssusb->phys[i])) { - dev_err(dev, "failed to get phy-%d\n", i); - return PTR_ERR(ssusb->phys[i]); - } - } - res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc"); ssusb->ippc_base = devm_ioremap_resource(dev, res); if (IS_ERR(ssusb->ippc_base)) @@ -457,7 +363,6 @@ static int __maybe_unused mtu3_suspend(struct device *dev) return 0; ssusb_host_disable(ssusb, true); - ssusb_phy_power_off(ssusb); ssusb_clks_disable(ssusb); ssusb_wakeup_set(ssusb, true); @@ -480,16 +385,10 @@ static int __maybe_unused mtu3_resume(struct device *dev) if (ret) goto clks_err; - ret = ssusb_phy_power_on(ssusb); - if (ret) - goto phy_err; - ssusb_host_enable(ssusb); return 0; -phy_err: - ssusb_clks_disable(ssusb); clks_err: return ret; }
The new PHY wrapper is now wired up in the core HCD code. This means that PHYs are now controlled (initialized, enabled, disabled, exited) without requiring any host-driver specific code. Remove the custom USB PHY handling from the mtu3 driver as the core HCD code now handles this. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- drivers/usb/mtu3/mtu3_plat.c | 101 ------------------------------------------- 1 file changed, 101 deletions(-)