@@ -918,6 +918,78 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev,
return 0;
}
+static int fsmc_nand_attach_chip(struct nand_chip *nand)
+{
+ struct mtd_info *mtd = nand_to_mtd(nand);
+ struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
+
+ if (AMBA_REV_BITS(host->pid) >= 8) {
+ switch (mtd->oobsize) {
+ case 16:
+ case 64:
+ case 128:
+ case 224:
+ case 256:
+ break;
+ default:
+ dev_warn(host->dev,
+ "No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
+ return -EINVAL;
+ }
+
+ mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops);
+
+ return 0;
+ }
+
+ switch (nand->ecc.mode) {
+ case NAND_ECC_HW:
+ dev_info(host->dev, "Using 1-bit HW ECC scheme\n");
+ nand->ecc.calculate = fsmc_read_hwecc_ecc1;
+ nand->ecc.correct = nand_correct_data;
+ nand->ecc.bytes = 3;
+ nand->ecc.strength = 1;
+ break;
+
+ case NAND_ECC_SOFT:
+ if (nand->ecc.algo == NAND_ECC_BCH) {
+ dev_info(host->dev,
+ "Using 4-bit SW BCH ECC scheme\n");
+ break;
+ }
+
+ case NAND_ECC_ON_DIE:
+ break;
+
+ default:
+ dev_err(host->dev, "Unsupported ECC mode!\n");
+ return -ENOTSUPP;
+ }
+
+ /*
+ * Don't set layout for BCH4 SW ECC. This will be
+ * generated later in nand_bch_init() later.
+ */
+ if (nand->ecc.mode == NAND_ECC_HW) {
+ switch (mtd->oobsize) {
+ case 16:
+ case 64:
+ case 128:
+ mtd_set_ooblayout(mtd,
+ &fsmc_ecc1_ooblayout_ops);
+ break;
+ default:
+ dev_warn(host->dev,
+ "No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
/*
* fsmc_nand_probe - Probe function
* @pdev: platform device structure
@@ -1047,76 +1119,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
/*
* Scan to find existence of the device
*/
- ret = nand_scan_ident(mtd, 1, NULL);
- if (ret) {
- dev_err(&pdev->dev, "No NAND Device found!\n");
- goto release_dma_write_chan;
- }
-
- if (AMBA_REV_BITS(host->pid) >= 8) {
- switch (mtd->oobsize) {
- case 16:
- case 64:
- case 128:
- case 224:
- case 256:
- break;
- default:
- dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n",
- mtd->oobsize);
- ret = -EINVAL;
- goto release_dma_write_chan;
- }
-
- mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops);
- } else {
- switch (nand->ecc.mode) {
- case NAND_ECC_HW:
- dev_info(&pdev->dev, "Using 1-bit HW ECC scheme\n");
- nand->ecc.calculate = fsmc_read_hwecc_ecc1;
- nand->ecc.correct = nand_correct_data;
- nand->ecc.bytes = 3;
- nand->ecc.strength = 1;
- break;
-
- case NAND_ECC_SOFT:
- if (nand->ecc.algo == NAND_ECC_BCH) {
- dev_info(&pdev->dev, "Using 4-bit SW BCH ECC scheme\n");
- break;
- }
-
- case NAND_ECC_ON_DIE:
- break;
-
- default:
- dev_err(&pdev->dev, "Unsupported ECC mode!\n");
- goto release_dma_write_chan;
- }
-
- /*
- * Don't set layout for BCH4 SW ECC. This will be
- * generated later in nand_bch_init() later.
- */
- if (nand->ecc.mode == NAND_ECC_HW) {
- switch (mtd->oobsize) {
- case 16:
- case 64:
- case 128:
- mtd_set_ooblayout(mtd,
- &fsmc_ecc1_ooblayout_ops);
- break;
- default:
- dev_warn(&pdev->dev,
- "No oob scheme defined for oobsize %d\n",
- mtd->oobsize);
- ret = -EINVAL;
- goto release_dma_write_chan;
- }
- }
- }
-
- /* Second stage of scan to fill MTD data-structures */
- ret = nand_scan_tail(mtd);
+ nand->hwcontrol.attach_chip = fsmc_nand_attach_chip;
+ ret = nand_scan(mtd, 1);
if (ret)
goto release_dma_write_chan;
Two helpers have been added to the core to make ECC-related configuration between the detection phase and the final NAND scan. Use these hooks and convert the driver to just use nand_scan() instead of both nand_scan_ident() and nand_scan_tail(). Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/mtd/nand/raw/fsmc_nand.c | 144 ++++++++++++++++++++------------------- 1 file changed, 74 insertions(+), 70 deletions(-)