new file mode 100644
@@ -0,0 +1,73 @@
+* Mediatek Image Signal Processor Pass 1 (ISP P1)
+
+The Pass 1 unit of Mediatek's camera ISP system grabs the sensor data out
+from the sensor interface, applies ISP effects from tuning data and outputs
+the image data and statistics data to DRAM. Furthermore, Pass 1 unit has
+the ability to output two different resolutions frames at the same time to
+increase the performance of the camera application.
+
+Required properties:
+- compatible: Must be "mediatek,mt8183-camisp" for MT8183.
+- reg: Physical base address of the camera function block register and
+ length of memory mapped region. Must contain an entry for each entry
+ in reg-names.
+- reg-names: Must include the following entries:
+ "cam_sys": Camera base function block
+ "cam_uni": Camera UNI function block
+ "cam_a": Camera ISP P1 hardware unit A
+ "cam_b": Camera ISP P1 hardware unit B
+ "cam_c": Camera ISP P1 hardware unit C
+- interrupts: Must contain an entry for each entry in interrupt-names.
+- interrupt-names : Must include the following entries:
+ "cam_uni": Camera UNI interrupt
+ "cam_a": Camera unit A interrupt
+ "cam_b": Camera unit B interrupt
+ "cam_c": Camera unit C interrupt
+- iommus: Shall point to the respective IOMMU block with master port
+ as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
+ for details.
+- clocks: A list of phandle and clock specifier pairs as listed
+ in clock-names property, see
+ Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
+- clock-names: Must be "camsys_cam_cgpdn" and "camsys_camtg_cgpdn".
+- mediatek,larb: Must contain the local arbiters in the current SoCs, see
+ Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
+ for details.
+- power-domains: a phandle to the power domain, see
+ Documentation/devicetree/bindings/power/power_domain.txt for details.
+- mediatek,scp : The node of system control processor (SCP), see
+ Documentation/devicetree/bindings/remoteproc/mtk,scp.txt for details.
+
+Example:
+SoC specific DT entry:
+
+ camisp: camisp@1a000000 {
+ compatible = "mediatek,mt8183-camisp";
+ reg = <0 0x1a000000 0 0x1000>,
+ <0 0x1a003000 0 0x1000>,
+ <0 0x1a004000 0 0x2000>,
+ <0 0x1a006000 0 0x2000>,
+ <0 0x1a008000 0 0x2000>;
+ reg-names = "cam_sys",
+ "cam_uni",
+ "cam_a",
+ "cam_b",
+ "cam_c";
+ interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 256 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "cam_uni",
+ "cam_a",
+ "cam_b",
+ "cam_c";
+ iommus = <&iommu M4U_PORT_CAM_IMGO>;
+ clocks = <&camsys CLK_CAM_CAM>,
+ <&camsys CLK_CAM_CAMTG>;
+ clock-names = "camsys_cam_cgpdn",
+ "camsys_camtg_cgpdn";
+ mediatek,larb = <&larb3>,
+ <&larb6>;
+ power-domains = <&scpsys MT8183_POWER_DOMAIN_CAM>;
+ mediatek,scp = <&scp>;
+ };
This patch adds DT binding document for the Pass 1 (P1) unit in Mediatek's camera ISP system. The Pass 1 unit grabs the sensor data out from the sensor interface, applies ISP image effects from tuning data and outputs the image data or statistics data to DRAM. Signed-off-by: Jungo Lin <jungo.lin@mediatek.com> --- .../bindings/media/mediatek,camisp.txt | 73 +++++++++++++++++++ 1 file changed, 73 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/mediatek,camisp.txt