diff mbox series

[v3,2/4] arm64: dts: mediatek: Add device-tree for MT8195 Demo board

Message ID 20220415150003.1793063-3-fparent@baylibre.com (mailing list archive)
State New, archived
Headers show
Series Add support for MediaTek MT8195 demo board | expand

Commit Message

Fabien Parent April 15, 2022, 3 p.m. UTC
Add basic device-tree for the MT8195 Demo board. The
Demo board is made by MediaTek and has a MT8195 SoC,
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.

The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 1 USB Type-A connector
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 uSD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage

This commit adds basic support in order to be able to boot.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
---
v3:
 * use plural for all pinctrl subnode names
 * reorder all nodes in alphabetical order
 * Remove invalid property for i2c6 pinctrl
 * use interrupts-extended instead of interrupts/interrupt-parent
 * rebase on top [v14,2/2] arm64: dts: Add mediatek SoC mt8195 and evaluation board
    -> https://patchwork.kernel.org/project/linux-mediatek/patch/20220411022724.11005-3-tinghan.shen@mediatek.com/

v2:
 * remove empty i2c nodes
 * remove empty spi node
 * remove unused pcie pinctrls
 * fixup node nodes to not contains underscore
 * rename mt6360 pmic node
 * move mmc1 node right after mmc0 node
 * use generic node name for gpio-keys
 * uniformize pinctrl node names

 arch/arm64/boot/dts/mediatek/Makefile        |   1 +
 arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 445 +++++++++++++++++++
 2 files changed, 446 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-demo.dts
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 5da29e7223e4..c7d4636a2cb7 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -38,5 +38,6 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
new file mode 100644
index 000000000000..def3fc26cb99
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
@@ -0,0 +1,445 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2022 BayLibre, SAS.
+ * Author: Fabien Parent <fparent@baylibre.com>
+ */
+/dts-v1/;
+
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+
+/ {
+	model = "MediaTek MT8195 demo board";
+	compatible = "mediatek,mt8195-demo", "mediatek,mt8195";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		key-0 {
+			gpios = <&pio 106 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@54600000 {
+			no-map;
+			reg = <0 0x54600000 0x0 0x30000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mt6360: pmic@34 {
+		compatible = "mediatek,mt6360";
+		reg = <0x34>;
+		interrupt-controller;
+		interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "IRQB";
+
+		charger {
+			compatible = "mediatek,mt6360-chg";
+			richtek,vinovp-microvolt = <14500000>;
+
+			otg_vbus_regulator: usb-otg-vbus-regulator {
+				regulator-compatible = "usb-otg-vbus";
+				regulator-name = "usb-otg-vbus";
+				regulator-min-microvolt = <4425000>;
+				regulator-max-microvolt = <5825000>;
+			};
+		};
+
+		regulator {
+			compatible = "mediatek,mt6360-regulator";
+			LDO_VIN3-supply = <&mt6360_buck2>;
+
+			mt6360_buck1: buck1 {
+				regulator-compatible = "BUCK1";
+				regulator-name = "mt6360,buck1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_buck2: buck2 {
+				regulator-compatible = "BUCK2";
+				regulator-name = "mt6360,buck2";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_ldo1: ldo1 {
+				regulator-compatible = "LDO1";
+				regulator-name = "mt6360,ldo1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo2: ldo2 {
+				regulator-compatible = "LDO2";
+				regulator-name = "mt6360,ldo2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo3: ldo3 {
+				regulator-compatible = "LDO3";
+				regulator-name = "mt6360,ldo3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo5: ldo5 {
+				regulator-compatible = "LDO5";
+				regulator-name = "mt6360,ldo5";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo6: ldo6 {
+				regulator-compatible = "LDO6";
+				regulator-name = "mt6360,ldo6";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo7: ldo7 {
+				regulator-compatible = "LDO7";
+				regulator-name = "mt6360,ldo7";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_default_pins>;
+	pinctrl-1 = <&mmc0_uhs_pins>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-hw-reset;
+	no-sdio;
+	no-sd;
+	hs400-ds-delay = <0x14c11>;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+	non-removable;
+};
+
+&mmc1 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_default_pins>;
+	pinctrl-1 = <&mmc1_uhs_pins>;
+	cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	max-frequency = <200000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&mt6360_ldo5>;
+	vqmmc-supply = <&mt6360_ldo3>;
+	status = "okay";
+};
+
+&mt6359_vbbck_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc1_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc2_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vpu_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_md_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_others_ldo_reg {
+	regulator-always-on;
+};
+
+&pio {
+	gpio_keys_pins: gpio-keys-pins {
+		pins {
+			pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
+			input-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-pins {
+		pins {
+			pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+				 <PINMUX_GPIO26__FUNC_SCL6>;
+			bias-pull-up;
+		};
+	};
+
+	mmc0_default_pins: mmc0-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_uhs_pins: mmc0-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_default_pins: mmc1-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-insert {
+			pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
+			bias-pull-up;
+		};
+	};
+
+	mmc1_uhs_pins: mmc1-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
+				 <PINMUX_GPIO99__FUNC_URXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <PINMUX_GPIO102__FUNC_UTXD1>,
+				 <PINMUX_GPIO103__FUNC_URXD1>;
+		};
+	};
+};
+
+
+&pmic {
+	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
+&u3phy3 {
+	status = "okay";
+};
+
+&xhci0 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&otg_vbus_regulator>;
+	status = "okay";
+};
+
+&xhci1 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci2 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci3 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};