| Message ID | 20220623115631.22209-8-peterwu.pub@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add Mediatek MT6370 PMIC support | expand |
On Thu, Jun 23, 2022 at 1:59 PM ChiaEn Wu <peterwu.pub@gmail.com> wrote: > > From: ChiYuan Huang <cy_huang@richtek.com> > > Add Mediatek MT6370 MFD support. ... > +config MFD_MT6370 > + tristate "Mediatek MT6370 SubPMIC" > + select MFD_CORE > + select REGMAP_I2C > + select REGMAP_IRQ > + depends on I2C > + help > + Say Y here to enable MT6370 SubPMIC functional support. > + It consists of a single cell battery charger with ADC monitoring, RGB > + LEDs, dual channel flashlight, WLED backlight driver, display bias > + voltage supply, one general purpose LDO, and the USB Type-C & PD > + controller complies with the latest USB Type-C and PD standards. What will be the module name in case it's chosen to be built as a module? ... > obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o > obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o > obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o > obj-$(CONFIG_MFD_MT6360) += mt6360-core.o > +obj-$(CONFIG_MFD_MT6370) += mt6370.o > mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o > obj-$(CONFIG_MFD_MT6397) += mt6397.o > obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o This whole bunch of drivers is in the wrong place in Makefile. https://lore.kernel.org/all/20220616182524.7956-2-andriy.shevchenko@linux.intel.com/ ... > +#define MT6370_REG_MAXADDR 0x1FF Wondering if (BIT(10) - 1) gives a better hint on how hardware limits this (so it will be clear it's 10-bit address). ... > +static int mt6370_check_vendor_info(struct mt6370_info *info) > +{ > + unsigned int devinfo; > + int ret; > + > + ret = regmap_read(info->regmap, MT6370_REG_DEV_INFO, &devinfo); > + if (ret) > + return ret; > + > + switch (FIELD_GET(MT6370_VENID_MASK, devinfo)) { > + case MT6370_VENID_RT5081: > + case MT6370_VENID_RT5081A: > + case MT6370_VENID_MT6370: > + case MT6370_VENID_MT6371: > + case MT6370_VENID_MT6372P: > + case MT6370_VENID_MT6372CP: return 0; > + break; > + default: > + dev_err(info->dev, "Unknown Vendor ID 0x%02x\n", devinfo); > + return -ENODEV; > + } > + > + return 0; ...and drop these two lines? > +} ... > + bank_idx = *(u8 *)reg_buf; > + bank_addr = *(u8 *)(reg_buf + 1); Why not const u8 *u8_buf = reg_buf; bank_idx = u8_buf[0]; bank_addr = u8_buf[1]; ? ... > + if (ret < 0) > + return ret; > + else if (ret != val_size) Redundant 'else'. > + return -EIO; ... > + bank_idx = *(u8 *)data; > + bank_addr = *(u8 *)(data + 1); As per above.
Hi Andy, Thanks for your helpful comments! We have some questions below. Andy Shevchenko <andy.shevchenko@gmail.com> 於 2022年6月24日 週五 凌晨2:01寫道： > > On Thu, Jun 23, 2022 at 1:59 PM ChiaEn Wu <peterwu.pub@gmail.com> wrote: > > > > From: ChiYuan Huang <cy_huang@richtek.com> > > > > Add Mediatek MT6370 MFD support. > > ... > > > +config MFD_MT6370 > > + tristate "Mediatek MT6370 SubPMIC" > > + select MFD_CORE > > + select REGMAP_I2C > > + select REGMAP_IRQ > > + depends on I2C > > + help > > + Say Y here to enable MT6370 SubPMIC functional support. > > + It consists of a single cell battery charger with ADC monitoring, RGB > > + LEDs, dual channel flashlight, WLED backlight driver, display bias > > + voltage supply, one general purpose LDO, and the USB Type-C & PD > > + controller complies with the latest USB Type-C and PD standards. > > What will be the module name in case it's chosen to be built as a module? OK, we will add related text in the next patch! Thanks! > > ... > > > obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o > > obj-$(CONFIG_MFD_MT6360) += mt6360-core.o > > +obj-$(CONFIG_MFD_MT6370) += mt6370.o > > mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o > > obj-$(CONFIG_MFD_MT6397) += mt6397.o > > obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o > > This whole bunch of drivers is in the wrong place in Makefile. > > https://lore.kernel.org/all/20220616182524.7956-2-andriy.shevchenko@linux.intel.com/ > hmm... So shall we need to cherry-pick your this patch first, then modify the Makefile before the next submission?? > ... > > > +#define MT6370_REG_MAXADDR 0x1FF > > Wondering if (BIT(10) - 1) gives a better hint on how hardware limits > this (so it will be clear it's 10-bit address). well... This "0x1FF" is just a virtual mapping value to map the max address of the PMU bank(0x1XX). So, I feel its means is different from using (BIT(10) - 1) here. > > ... > > > +static int mt6370_check_vendor_info(struct mt6370_info *info) > > +{ > > + unsigned int devinfo; > > + int ret; > > + > > + ret = regmap_read(info->regmap, MT6370_REG_DEV_INFO, &devinfo); > > + if (ret) > > + return ret; > > + > > + switch (FIELD_GET(MT6370_VENID_MASK, devinfo)) { > > + case MT6370_VENID_RT5081: > > + case MT6370_VENID_RT5081A: > > + case MT6370_VENID_MT6370: > > + case MT6370_VENID_MT6371: > > + case MT6370_VENID_MT6372P: > > + case MT6370_VENID_MT6372CP: > > return 0; > > > + break; > > + default: > > + dev_err(info->dev, "Unknown Vendor ID 0x%02x\n", devinfo); > > + return -ENODEV; > > + } > > + > > + return 0; > > ...and drop these two lines? OK! We will refine it in the next patch! > > > +} > > ... > > > + bank_idx = *(u8 *)reg_buf; > > + bank_addr = *(u8 *)(reg_buf + 1); > > Why not > > const u8 *u8_buf = reg_buf; > > bank_idx = u8_buf[0]; > bank_addr = u8_buf[1]; > > ? We will refine it in the next patch! Thanks! > > ... > > > + if (ret < 0) > > + return ret; > > + else if (ret != val_size) > > Redundant 'else'. I'm not quite sure what you mean, so I made the following changes first. ------------------------------------ if (ret < 0) return ret; if (ret != val_size) return -EIO; ------------------------------------ I don't know if it meets your expectations?? > > > + return -EIO; > > ... > > > + bank_idx = *(u8 *)data; > > + bank_addr = *(u8 *)(data + 1); > > As per above. > > -- > With Best Regards, > Andy Shevchenko Best regards, ChiaEn Wu
On Fri, Jun 24, 2022 at 12:19 PM ChiaEn Wu <peterwu.pub@gmail.com> wrote: > Andy Shevchenko <andy.shevchenko@gmail.com> 於 2022年6月24日 週五 凌晨2:01寫道： > > On Thu, Jun 23, 2022 at 1:59 PM ChiaEn Wu <peterwu.pub@gmail.com> wrote: ... > > > obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o > > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o > > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o > > > obj-$(CONFIG_MFD_MT6360) += mt6360-core.o > > > +obj-$(CONFIG_MFD_MT6370) += mt6370.o > > > mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o > > > obj-$(CONFIG_MFD_MT6397) += mt6397.o > > > obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o > > > > This whole bunch of drivers is in the wrong place in Makefile. > > > > https://lore.kernel.org/all/20220616182524.7956-2-andriy.shevchenko@linux.intel.com/ > > hmm... So shall we need to cherry-pick your this patch first, > then modify the Makefile before the next submission?? I don't know what Lee's preferences are, but at least I have these options in mind: 1) wait until Lee applies my series; 2) take that single patch to your tree as a precursor. In the second case you will need to send the series with that patch as well. ... > > > +#define MT6370_REG_MAXADDR 0x1FF > > > > Wondering if (BIT(10) - 1) gives a better hint on how hardware limits > > this (so it will be clear it's 10-bit address). > > well... This "0x1FF" is just a virtual mapping value to map the max > address of the PMU bank(0x1XX). > So, I feel its means is different from using (BIT(10) - 1) here. Perhaps a comment then? ... > > > + if (ret < 0) > > > + return ret; > > > + else if (ret != val_size) > > > > Redundant 'else'. > > I'm not quite sure what you mean, so I made the following changes first. > ------------------------------------ > if (ret < 0) > return ret; > if (ret != val_size) > return -EIO; > ------------------------------------ > I don't know if it meets your expectations?? Yes. > > > + return -EIO;
On Thu, 23 Jun 2022, ChiaEn Wu wrote: > From: ChiYuan Huang <cy_huang@richtek.com> > > Add Mediatek MT6370 MFD support. No such thing as "MFD support". And you're not getting away with submitting a 370 line patch with a 5 word change log either. :) Please at least tell us what the device is and what it's used for. > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > --- > > v3 > - Refine Kconfig help text > - Refine error message of unknown vendor ID in > mt6370_check_vendor_info() > - Refine return value handling of mt6370_regmap_read() > - Refine all probe error by using dev_err_probe() > - Refine "bank_idx" and "bank_addr" in mt6370_regmap_read() and > mt6370_regmap_write() > - Add "#define VENID*" and drop the comments in > mt6370_check_vendor_info() > - Drop "MFD" in MODULE_DESCRIPTION() > --- > drivers/mfd/Kconfig | 13 ++ > drivers/mfd/Makefile | 1 + > drivers/mfd/mt6370.c | 358 +++++++++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 372 insertions(+) > create mode 100644 drivers/mfd/mt6370.c > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 3b59456..4c900c4 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -937,6 +937,19 @@ config MFD_MT6360 > PMIC part includes 2-channel BUCKs and 2-channel LDOs > LDO part includes 4-channel LDOs > > +config MFD_MT6370 > + tristate "Mediatek MT6370 SubPMIC" > + select MFD_CORE > + select REGMAP_I2C > + select REGMAP_IRQ > + depends on I2C > + help > + Say Y here to enable MT6370 SubPMIC functional support. > + It consists of a single cell battery charger with ADC monitoring, RGB > + LEDs, dual channel flashlight, WLED backlight driver, display bias > + voltage supply, one general purpose LDO, and the USB Type-C & PD > + controller complies with the latest USB Type-C and PD standards. > + > config MFD_MT6397 > tristate "MediaTek MT6397 PMIC Support" > select MFD_CORE > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index 858cacf..62b2712 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -242,6 +242,7 @@ obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o > obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o > obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o > obj-$(CONFIG_MFD_MT6360) += mt6360-core.o > +obj-$(CONFIG_MFD_MT6370) += mt6370.o > mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o > obj-$(CONFIG_MFD_MT6397) += mt6397.o > obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o > diff --git a/drivers/mfd/mt6370.c b/drivers/mfd/mt6370.c > new file mode 100644 > index 0000000..49f02b1 > --- /dev/null > +++ b/drivers/mfd/mt6370.c > @@ -0,0 +1,358 @@ > +// SPDX-License-Identifier: GPL-2.0 No Copyright? > +#include <linux/bits.h> > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/mfd/core.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > + > +enum { > + MT6370_USBC_I2C = 0, > + MT6370_PMU_I2C, > + MT6370_MAX_I2C > +}; > + > +#define MT6370_REG_DEV_INFO 0x100 > +#define MT6370_REG_CHG_IRQ1 0x1C0 > +#define MT6370_REG_CHG_MASK1 0x1E0 > + > +#define MT6370_VENID_MASK GENMASK(7, 4) > + > +#define MT6370_NUM_IRQREGS 16 > +#define MT6370_USBC_I2CADDR 0x4E > +#define MT6370_REG_ADDRLEN 2 > +#define MT6370_REG_MAXADDR 0x1FF > + > +#define MT6370_VENID_RT5081 0x8 > +#define MT6370_VENID_RT5081A 0xA > +#define MT6370_VENID_MT6370 0xE > +#define MT6370_VENID_MT6371 0xF > +#define MT6370_VENID_MT6372P 0x9 > +#define MT6370_VENID_MT6372CP 0xB > + > +/* IRQ definitions */ > +#define MT6370_IRQ_DIRCHGON 0 > +#define MT6370_IRQ_CHG_TREG 4 > +#define MT6370_IRQ_CHG_AICR 5 > +#define MT6370_IRQ_CHG_MIVR 6 > +#define MT6370_IRQ_PWR_RDY 7 > +#define MT6370_IRQ_FL_CHG_VINOVP 11 > +#define MT6370_IRQ_CHG_VSYSUV 12 > +#define MT6370_IRQ_CHG_VSYSOV 13 > +#define MT6370_IRQ_CHG_VBATOV 14 > +#define MT6370_IRQ_CHG_VINOVPCHG 15 > +#define MT6370_IRQ_TS_BAT_COLD 20 > +#define MT6370_IRQ_TS_BAT_COOL 21 > +#define MT6370_IRQ_TS_BAT_WARM 22 > +#define MT6370_IRQ_TS_BAT_HOT 23 > +#define MT6370_IRQ_TS_STATC 24 > +#define MT6370_IRQ_CHG_FAULT 25 > +#define MT6370_IRQ_CHG_STATC 26 > +#define MT6370_IRQ_CHG_TMR 27 > +#define MT6370_IRQ_CHG_BATABS 28 > +#define MT6370_IRQ_CHG_ADPBAD 29 > +#define MT6370_IRQ_CHG_RVP 30 > +#define MT6370_IRQ_TSHUTDOWN 31 > +#define MT6370_IRQ_CHG_IINMEAS 32 > +#define MT6370_IRQ_CHG_ICCMEAS 33 > +#define MT6370_IRQ_CHGDET_DONE 34 > +#define MT6370_IRQ_WDTMR 35 > +#define MT6370_IRQ_SSFINISH 36 > +#define MT6370_IRQ_CHG_RECHG 37 > +#define MT6370_IRQ_CHG_TERM 38 > +#define MT6370_IRQ_CHG_IEOC 39 > +#define MT6370_IRQ_ADC_DONE 40 > +#define MT6370_IRQ_PUMPX_DONE 41 > +#define MT6370_IRQ_BST_BATUV 45 > +#define MT6370_IRQ_BST_MIDOV 46 > +#define MT6370_IRQ_BST_OLP 47 > +#define MT6370_IRQ_ATTACH 48 > +#define MT6370_IRQ_DETACH 49 > +#define MT6370_IRQ_HVDCP_STPDONE 51 > +#define MT6370_IRQ_HVDCP_VBUSDET_DONE 52 > +#define MT6370_IRQ_HVDCP_DET 53 > +#define MT6370_IRQ_CHGDET 54 > +#define MT6370_IRQ_DCDT 55 > +#define MT6370_IRQ_DIRCHG_VGOK 59 > +#define MT6370_IRQ_DIRCHG_WDTMR 60 > +#define MT6370_IRQ_DIRCHG_UC 61 > +#define MT6370_IRQ_DIRCHG_OC 62 > +#define MT6370_IRQ_DIRCHG_OV 63 > +#define MT6370_IRQ_OVPCTRL_SWON 67 > +#define MT6370_IRQ_OVPCTRL_UVP_D 68 > +#define MT6370_IRQ_OVPCTRL_UVP 69 > +#define MT6370_IRQ_OVPCTRL_OVP_D 70 > +#define MT6370_IRQ_OVPCTRL_OVP 71 > +#define MT6370_IRQ_FLED_STRBPIN 72 > +#define MT6370_IRQ_FLED_TORPIN 73 > +#define MT6370_IRQ_FLED_TX 74 > +#define MT6370_IRQ_FLED_LVF 75 > +#define MT6370_IRQ_FLED2_SHORT 78 > +#define MT6370_IRQ_FLED1_SHORT 79 > +#define MT6370_IRQ_FLED2_STRB 80 > +#define MT6370_IRQ_FLED1_STRB 81 > +#define mT6370_IRQ_FLED2_STRB_TO 82 > +#define MT6370_IRQ_FLED1_STRB_TO 83 > +#define MT6370_IRQ_FLED2_TOR 84 > +#define MT6370_IRQ_FLED1_TOR 85 > +#define MT6370_IRQ_OTP 93 > +#define MT6370_IRQ_VDDA_OVP 94 > +#define MT6370_IRQ_VDDA_UV 95 > +#define MT6370_IRQ_LDO_OC 103 > +#define MT6370_IRQ_BLED_OCP 118 > +#define MT6370_IRQ_BLED_OVP 119 > +#define MT6370_IRQ_DSV_VNEG_OCP 123 > +#define MT6370_IRQ_DSV_VPOS_OCP 124 > +#define MT6370_IRQ_DSV_BST_OCP 125 > +#define MT6370_IRQ_DSV_VNEG_SCP 126 > +#define MT6370_IRQ_DSV_VPOS_SCP 127 Can you pop these into a header file please? > +struct mt6370_info { > + struct i2c_client *i2c[MT6370_MAX_I2C]; > + struct device *dev; You don't need both 'i2c' and 'dev'. You can derive one from the other. > + struct regmap *regmap; > + struct regmap_irq_chip_data *irq_data; > +}; This can do into the header file too. > +static const struct regmap_irq mt6370_irqs[] = { > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHGON, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TREG, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_AICR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_MIVR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PWR_RDY, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FL_CHG_VINOVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSUV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSOV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VBATOV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VINOVPCHG, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COLD, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COOL, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_WARM, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_HOT, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_STATC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_FAULT, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_STATC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TMR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_BATABS, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ADPBAD, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TSHUTDOWN, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IINMEAS, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ICCMEAS, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET_DONE, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_WDTMR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_SSFINISH, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RECHG, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TERM, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IEOC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ADC_DONE, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PUMPX_DONE, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_BATUV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_MIDOV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_OLP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ATTACH, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DETACH, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_STPDONE, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_VBUSDET_DONE, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_DET, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DCDT, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_VGOK, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_WDTMR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_UC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_SWON, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP_D, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP_D, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_STRBPIN, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TORPIN, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TX, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_LVF, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_SHORT, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_SHORT, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_STRB, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB, 8), > + REGMAP_IRQ_REG_LINE(mT6370_IRQ_FLED2_STRB_TO, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB_TO, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_TOR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_TOR, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OTP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_OVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_UV, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_LDO_OC, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OCP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OVP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_OCP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_OCP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_BST_OCP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_SCP, 8), > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_SCP, 8) > +}; > + > +static const struct regmap_irq_chip mt6370_irq_chip = { > + .name = "mt6370-irqs", > + .status_base = MT6370_REG_CHG_IRQ1, > + .mask_base = MT6370_REG_CHG_MASK1, > + .num_regs = MT6370_NUM_IRQREGS, > + .irqs = mt6370_irqs, > + .num_irqs = ARRAY_SIZE(mt6370_irqs), > +}; > + > +static const struct resource mt6370_regulator_irqs[] = { > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_SCP, "db_vpos_scp"), > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_SCP, "db_vneg_scp"), > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_BST_OCP, "db_vbst_ocp"), > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_OCP, "db_vpos_ocp"), > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_OCP, "db_vneg_ocp"), > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_LDO_OC, "ldo_oc") > +}; > + > +static const struct mfd_cell mt6370_devices[] = { > + MFD_CELL_OF("adc", NULL, NULL, 0, 0, "mediatek,mt6370-adc"), > + MFD_CELL_OF("charger", NULL, NULL, 0, 0, "mediatek,mt6370-charger"), > + MFD_CELL_OF("backlight", NULL, NULL, 0, 0, "mediatek,mt6370-backlight"), > + MFD_CELL_OF("flashlight", NULL, NULL, 0, 0, "mediatek,mt6370-flashlight"), > + MFD_CELL_OF("indicator", NULL, NULL, 0, 0, "mediatek,mt6370-indicator"), > + MFD_CELL_OF("tcpc", NULL, NULL, 0, 0, "mediatek,mt6370-tcpc"), > + MFD_CELL_RES("regulator", mt6370_regulator_irqs) The first parameters here should be prepended with something, perhaps "mt6370_"? > +}; > + > +static int mt6370_check_vendor_info(struct mt6370_info *info) > +{ > + unsigned int devinfo; > + int ret; > + > + ret = regmap_read(info->regmap, MT6370_REG_DEV_INFO, &devinfo); > + if (ret) > + return ret; > + > + switch (FIELD_GET(MT6370_VENID_MASK, devinfo)) { > + case MT6370_VENID_RT5081: > + case MT6370_VENID_RT5081A: > + case MT6370_VENID_MT6370: > + case MT6370_VENID_MT6371: > + case MT6370_VENID_MT6372P: > + case MT6370_VENID_MT6372CP: > + break; > + default: > + dev_err(info->dev, "Unknown Vendor ID 0x%02x\n", devinfo); > + return -ENODEV; > + } > + > + return 0; > +} > + > +static int mt6370_regmap_read(void *context, const void *reg_buf, > + size_t reg_size, void *val_buf, size_t val_size) > +{ > + struct mt6370_info *info = context; > + u8 bank_idx, bank_addr; > + int ret; > + > + bank_idx = *(u8 *)reg_buf; > + bank_addr = *(u8 *)(reg_buf + 1); > + > + ret = i2c_smbus_read_i2c_block_data(info->i2c[bank_idx], bank_addr, > + val_size, val_buf); > + if (ret < 0) > + return ret; > + else if (ret != val_size) > + return -EIO; > + > + return 0; > +} > + > +static int mt6370_regmap_write(void *context, const void *data, size_t count) > +{ > + struct mt6370_info *info = context; > + u8 bank_idx, bank_addr; > + int len = count - MT6370_REG_ADDRLEN; > + > + bank_idx = *(u8 *)data; > + bank_addr = *(u8 *)(data + 1); > + > + return i2c_smbus_write_i2c_block_data(info->i2c[bank_idx], bank_addr, > + len, data + MT6370_REG_ADDRLEN); > +} > + > +static const struct regmap_bus mt6370_regmap_bus = { > + .read = mt6370_regmap_read, > + .write = mt6370_regmap_write, > +}; > + > +static const struct regmap_config mt6370_regmap_config = { > + .reg_bits = 16, > + .val_bits = 8, > + .reg_format_endian = REGMAP_ENDIAN_BIG, > + .max_register = MT6370_REG_MAXADDR, > +}; > + > +static int mt6370_probe(struct i2c_client *i2c) > +{ > + struct mt6370_info *info; > + struct i2c_client *usbc_i2c; > + int ret; > + > + info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL); > + if (!info) > + return -ENOMEM; > + > + info->dev = &i2c->dev; > + > + usbc_i2c = devm_i2c_new_dummy_device(&i2c->dev, i2c->adapter, > + MT6370_USBC_I2CADDR); > + if (IS_ERR(usbc_i2c)) > + return dev_err_probe(&i2c->dev, PTR_ERR(usbc_i2c), > + "Failed to register USBC I2C client\n"); > + > + /* Assign I2C client for PMU and TypeC */ > + info->i2c[MT6370_PMU_I2C] = i2c; > + info->i2c[MT6370_USBC_I2C] = usbc_i2c; > + > + info->regmap = devm_regmap_init(&i2c->dev, &mt6370_regmap_bus, info, > + &mt6370_regmap_config); Apart from in mt6370_check_vendor_info() where is this actually used? > + if (IS_ERR(info->regmap)) > + return dev_err_probe(&i2c->dev, PTR_ERR(info->regmap), > + "Failed to register regmap\n"); > + > + ret = mt6370_check_vendor_info(info); > + if (ret) > + return dev_err_probe(&i2c->dev, ret, > + "Failed to check vendor info\n"); > + > + ret = devm_regmap_add_irq_chip(&i2c->dev, info->regmap, i2c->irq, > + IRQF_ONESHOT, -1, &mt6370_irq_chip, > + &info->irq_data); > + if (ret) > + return dev_err_probe(&i2c->dev, ret, > + "Failed to add irq chip\n"); > + > + return devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, > + mt6370_devices, ARRAY_SIZE(mt6370_devices), > + NULL, 0, > + regmap_irq_get_domain(info->irq_data)); > +} > + > +static const struct of_device_id mt6370_match_table[] = { > + { .compatible = "mediatek,mt6370", }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, mt6370_match_table); > + > +static struct i2c_driver mt6370_driver = { > + .driver = { > + .name = "mt6370", > + .of_match_table = mt6370_match_table, > + }, > + .probe_new = mt6370_probe, > +}; > +module_i2c_driver(mt6370_driver); > + > +MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>"); > +MODULE_DESCRIPTION("MT6370 I2C Driver"); This is not an I2C driver. > +MODULE_LICENSE("GPL v2");
Hi Lee, Thanks for your reply. Lee Jones <lee.jones@linaro.org> 於 2022年7月12日 週二 晚上11:29寫道： > > On Thu, 23 Jun 2022, ChiaEn Wu wrote: > > > From: ChiYuan Huang <cy_huang@richtek.com> > > > > Add Mediatek MT6370 MFD support. > > No such thing as "MFD support". > > And you're not getting away with submitting a 370 line patch with a 5 > word change log either. :) > > Please at least tell us what the device is and what it's used for. I sincerely apologize. We will add more descriptions of the MT6370 feature in the v5 patch. > > > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > > --- > > > > v3 > > - Refine Kconfig help text > > - Refine error message of unknown vendor ID in > > mt6370_check_vendor_info() > > - Refine return value handling of mt6370_regmap_read() > > - Refine all probe error by using dev_err_probe() > > - Refine "bank_idx" and "bank_addr" in mt6370_regmap_read() and > > mt6370_regmap_write() > > - Add "#define VENID*" and drop the comments in > > mt6370_check_vendor_info() > > - Drop "MFD" in MODULE_DESCRIPTION() > > --- > > drivers/mfd/Kconfig | 13 ++ > > drivers/mfd/Makefile | 1 + > > drivers/mfd/mt6370.c | 358 +++++++++++++++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 372 insertions(+) > > create mode 100644 drivers/mfd/mt6370.c > > > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > > index 3b59456..4c900c4 100644 > > --- a/drivers/mfd/Kconfig > > +++ b/drivers/mfd/Kconfig > > @@ -937,6 +937,19 @@ config MFD_MT6360 > > PMIC part includes 2-channel BUCKs and 2-channel LDOs > > LDO part includes 4-channel LDOs > > > > +config MFD_MT6370 > > + tristate "Mediatek MT6370 SubPMIC" > > + select MFD_CORE > > + select REGMAP_I2C > > + select REGMAP_IRQ > > + depends on I2C > > + help > > + Say Y here to enable MT6370 SubPMIC functional support. > > + It consists of a single cell battery charger with ADC monitoring, RGB > > + LEDs, dual channel flashlight, WLED backlight driver, display bias > > + voltage supply, one general purpose LDO, and the USB Type-C & PD > > + controller complies with the latest USB Type-C and PD standards. > > + > > config MFD_MT6397 > > tristate "MediaTek MT6397 PMIC Support" > > select MFD_CORE > > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > > index 858cacf..62b2712 100644 > > --- a/drivers/mfd/Makefile > > +++ b/drivers/mfd/Makefile > > @@ -242,6 +242,7 @@ obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o > > obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o > > obj-$(CONFIG_MFD_MT6360) += mt6360-core.o > > +obj-$(CONFIG_MFD_MT6370) += mt6370.o > > mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o > > obj-$(CONFIG_MFD_MT6397) += mt6397.o > > obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o > > diff --git a/drivers/mfd/mt6370.c b/drivers/mfd/mt6370.c > > new file mode 100644 > > index 0000000..49f02b1 > > --- /dev/null > > +++ b/drivers/mfd/mt6370.c > > @@ -0,0 +1,358 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > No Copyright? We have already added Copyright in the v4 patch. > > > +#include <linux/bits.h> > > +#include <linux/i2c.h> > > +#include <linux/interrupt.h> > > +#include <linux/kernel.h> > > +#include <linux/mfd/core.h> > > +#include <linux/module.h> > > +#include <linux/regmap.h> > > + > > +enum { > > + MT6370_USBC_I2C = 0, > > + MT6370_PMU_I2C, > > + MT6370_MAX_I2C > > +}; > > + > > +#define MT6370_REG_DEV_INFO 0x100 > > +#define MT6370_REG_CHG_IRQ1 0x1C0 > > +#define MT6370_REG_CHG_MASK1 0x1E0 > > + > > +#define MT6370_VENID_MASK GENMASK(7, 4) > > + > > +#define MT6370_NUM_IRQREGS 16 > > +#define MT6370_USBC_I2CADDR 0x4E > > +#define MT6370_REG_ADDRLEN 2 > > +#define MT6370_REG_MAXADDR 0x1FF > > + > > +#define MT6370_VENID_RT5081 0x8 > > +#define MT6370_VENID_RT5081A 0xA > > +#define MT6370_VENID_MT6370 0xE > > +#define MT6370_VENID_MT6371 0xF > > +#define MT6370_VENID_MT6372P 0x9 > > +#define MT6370_VENID_MT6372CP 0xB > > + > > +/* IRQ definitions */ > > +#define MT6370_IRQ_DIRCHGON 0 > > +#define MT6370_IRQ_CHG_TREG 4 > > +#define MT6370_IRQ_CHG_AICR 5 > > +#define MT6370_IRQ_CHG_MIVR 6 > > +#define MT6370_IRQ_PWR_RDY 7 > > +#define MT6370_IRQ_FL_CHG_VINOVP 11 > > +#define MT6370_IRQ_CHG_VSYSUV 12 > > +#define MT6370_IRQ_CHG_VSYSOV 13 > > +#define MT6370_IRQ_CHG_VBATOV 14 > > +#define MT6370_IRQ_CHG_VINOVPCHG 15 > > +#define MT6370_IRQ_TS_BAT_COLD 20 > > +#define MT6370_IRQ_TS_BAT_COOL 21 > > +#define MT6370_IRQ_TS_BAT_WARM 22 > > +#define MT6370_IRQ_TS_BAT_HOT 23 > > +#define MT6370_IRQ_TS_STATC 24 > > +#define MT6370_IRQ_CHG_FAULT 25 > > +#define MT6370_IRQ_CHG_STATC 26 > > +#define MT6370_IRQ_CHG_TMR 27 > > +#define MT6370_IRQ_CHG_BATABS 28 > > +#define MT6370_IRQ_CHG_ADPBAD 29 > > +#define MT6370_IRQ_CHG_RVP 30 > > +#define MT6370_IRQ_TSHUTDOWN 31 > > +#define MT6370_IRQ_CHG_IINMEAS 32 > > +#define MT6370_IRQ_CHG_ICCMEAS 33 > > +#define MT6370_IRQ_CHGDET_DONE 34 > > +#define MT6370_IRQ_WDTMR 35 > > +#define MT6370_IRQ_SSFINISH 36 > > +#define MT6370_IRQ_CHG_RECHG 37 > > +#define MT6370_IRQ_CHG_TERM 38 > > +#define MT6370_IRQ_CHG_IEOC 39 > > +#define MT6370_IRQ_ADC_DONE 40 > > +#define MT6370_IRQ_PUMPX_DONE 41 > > +#define MT6370_IRQ_BST_BATUV 45 > > +#define MT6370_IRQ_BST_MIDOV 46 > > +#define MT6370_IRQ_BST_OLP 47 > > +#define MT6370_IRQ_ATTACH 48 > > +#define MT6370_IRQ_DETACH 49 > > +#define MT6370_IRQ_HVDCP_STPDONE 51 > > +#define MT6370_IRQ_HVDCP_VBUSDET_DONE 52 > > +#define MT6370_IRQ_HVDCP_DET 53 > > +#define MT6370_IRQ_CHGDET 54 > > +#define MT6370_IRQ_DCDT 55 > > +#define MT6370_IRQ_DIRCHG_VGOK 59 > > +#define MT6370_IRQ_DIRCHG_WDTMR 60 > > +#define MT6370_IRQ_DIRCHG_UC 61 > > +#define MT6370_IRQ_DIRCHG_OC 62 > > +#define MT6370_IRQ_DIRCHG_OV 63 > > +#define MT6370_IRQ_OVPCTRL_SWON 67 > > +#define MT6370_IRQ_OVPCTRL_UVP_D 68 > > +#define MT6370_IRQ_OVPCTRL_UVP 69 > > +#define MT6370_IRQ_OVPCTRL_OVP_D 70 > > +#define MT6370_IRQ_OVPCTRL_OVP 71 > > +#define MT6370_IRQ_FLED_STRBPIN 72 > > +#define MT6370_IRQ_FLED_TORPIN 73 > > +#define MT6370_IRQ_FLED_TX 74 > > +#define MT6370_IRQ_FLED_LVF 75 > > +#define MT6370_IRQ_FLED2_SHORT 78 > > +#define MT6370_IRQ_FLED1_SHORT 79 > > +#define MT6370_IRQ_FLED2_STRB 80 > > +#define MT6370_IRQ_FLED1_STRB 81 > > +#define mT6370_IRQ_FLED2_STRB_TO 82 > > +#define MT6370_IRQ_FLED1_STRB_TO 83 > > +#define MT6370_IRQ_FLED2_TOR 84 > > +#define MT6370_IRQ_FLED1_TOR 85 > > +#define MT6370_IRQ_OTP 93 > > +#define MT6370_IRQ_VDDA_OVP 94 > > +#define MT6370_IRQ_VDDA_UV 95 > > +#define MT6370_IRQ_LDO_OC 103 > > +#define MT6370_IRQ_BLED_OCP 118 > > +#define MT6370_IRQ_BLED_OVP 119 > > +#define MT6370_IRQ_DSV_VNEG_OCP 123 > > +#define MT6370_IRQ_DSV_VPOS_OCP 124 > > +#define MT6370_IRQ_DSV_BST_OCP 125 > > +#define MT6370_IRQ_DSV_VNEG_SCP 126 > > +#define MT6370_IRQ_DSV_VPOS_SCP 127 > > Can you pop these into a header file please? We have already popped them into "mt6370.h" in the v4 patch. > > > +struct mt6370_info { > > + struct i2c_client *i2c[MT6370_MAX_I2C]; > > + struct device *dev; > > You don't need both 'i2c' and 'dev'. > > You can derive one from the other. > > > + struct regmap *regmap; > > + struct regmap_irq_chip_data *irq_data; > > +}; > > This can do into the header file too. > > > +static const struct regmap_irq mt6370_irqs[] = { > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHGON, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TREG, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_AICR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_MIVR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PWR_RDY, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FL_CHG_VINOVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSUV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSOV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VBATOV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VINOVPCHG, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COLD, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COOL, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_WARM, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_HOT, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_STATC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_FAULT, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_STATC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TMR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_BATABS, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ADPBAD, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TSHUTDOWN, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IINMEAS, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ICCMEAS, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET_DONE, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_WDTMR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_SSFINISH, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RECHG, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TERM, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IEOC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ADC_DONE, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PUMPX_DONE, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_BATUV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_MIDOV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_OLP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ATTACH, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DETACH, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_STPDONE, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_VBUSDET_DONE, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_DET, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DCDT, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_VGOK, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_WDTMR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_UC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_SWON, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP_D, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP_D, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_STRBPIN, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TORPIN, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TX, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_LVF, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_SHORT, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_SHORT, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_STRB, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB, 8), > > + REGMAP_IRQ_REG_LINE(mT6370_IRQ_FLED2_STRB_TO, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB_TO, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_TOR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_TOR, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OTP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_OVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_UV, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_LDO_OC, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OCP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OVP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_OCP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_OCP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_BST_OCP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_SCP, 8), > > + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_SCP, 8) > > +}; > > + > > +static const struct regmap_irq_chip mt6370_irq_chip = { > > + .name = "mt6370-irqs", > > + .status_base = MT6370_REG_CHG_IRQ1, > > + .mask_base = MT6370_REG_CHG_MASK1, > > + .num_regs = MT6370_NUM_IRQREGS, > > + .irqs = mt6370_irqs, > > + .num_irqs = ARRAY_SIZE(mt6370_irqs), > > +}; > > + > > +static const struct resource mt6370_regulator_irqs[] = { > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_SCP, "db_vpos_scp"), > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_SCP, "db_vneg_scp"), > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_BST_OCP, "db_vbst_ocp"), > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_OCP, "db_vpos_ocp"), > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_OCP, "db_vneg_ocp"), > > + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_LDO_OC, "ldo_oc") > > +}; > > + > > +static const struct mfd_cell mt6370_devices[] = { > > + MFD_CELL_OF("adc", NULL, NULL, 0, 0, "mediatek,mt6370-adc"), > > + MFD_CELL_OF("charger", NULL, NULL, 0, 0, "mediatek,mt6370-charger"), > > + MFD_CELL_OF("backlight", NULL, NULL, 0, 0, "mediatek,mt6370-backlight"), > > + MFD_CELL_OF("flashlight", NULL, NULL, 0, 0, "mediatek,mt6370-flashlight"), > > + MFD_CELL_OF("indicator", NULL, NULL, 0, 0, "mediatek,mt6370-indicator"), > > + MFD_CELL_OF("tcpc", NULL, NULL, 0, 0, "mediatek,mt6370-tcpc"), > > + MFD_CELL_RES("regulator", mt6370_regulator_irqs) > > The first parameters here should be prepended with something, perhaps > "mt6370_"? OK, we will add the prefix in the next patch. > > > +}; > > + > > +static int mt6370_check_vendor_info(struct mt6370_info *info) > > +{ > > + unsigned int devinfo; > > + int ret; > > + > > + ret = regmap_read(info->regmap, MT6370_REG_DEV_INFO, &devinfo); > > + if (ret) > > + return ret; > > + > > + switch (FIELD_GET(MT6370_VENID_MASK, devinfo)) { > > + case MT6370_VENID_RT5081: > > + case MT6370_VENID_RT5081A: > > + case MT6370_VENID_MT6370: > > + case MT6370_VENID_MT6371: > > + case MT6370_VENID_MT6372P: > > + case MT6370_VENID_MT6372CP: > > + break; > > + default: > > + dev_err(info->dev, "Unknown Vendor ID 0x%02x\n", devinfo); > > + return -ENODEV; > > + } > > + > > + return 0; > > +} > > + > > +static int mt6370_regmap_read(void *context, const void *reg_buf, > > + size_t reg_size, void *val_buf, size_t val_size) > > +{ > > + struct mt6370_info *info = context; > > + u8 bank_idx, bank_addr; > > + int ret; > > + > > + bank_idx = *(u8 *)reg_buf; > > + bank_addr = *(u8 *)(reg_buf + 1); > > + > > + ret = i2c_smbus_read_i2c_block_data(info->i2c[bank_idx], bank_addr, > > + val_size, val_buf); > > + if (ret < 0) > > + return ret; > > + else if (ret != val_size) > > + return -EIO; > > + > > + return 0; > > +} > > + > > +static int mt6370_regmap_write(void *context, const void *data, size_t count) > > +{ > > + struct mt6370_info *info = context; > > + u8 bank_idx, bank_addr; > > + int len = count - MT6370_REG_ADDRLEN; > > + > > + bank_idx = *(u8 *)data; > > + bank_addr = *(u8 *)(data + 1); > > + > > + return i2c_smbus_write_i2c_block_data(info->i2c[bank_idx], bank_addr, > > + len, data + MT6370_REG_ADDRLEN); > > +} > > + > > +static const struct regmap_bus mt6370_regmap_bus = { > > + .read = mt6370_regmap_read, > > + .write = mt6370_regmap_write, > > +}; > > + > > +static const struct regmap_config mt6370_regmap_config = { > > + .reg_bits = 16, > > + .val_bits = 8, > > + .reg_format_endian = REGMAP_ENDIAN_BIG, > > + .max_register = MT6370_REG_MAXADDR, > > +}; > > + > > +static int mt6370_probe(struct i2c_client *i2c) > > +{ > > + struct mt6370_info *info; > > + struct i2c_client *usbc_i2c; > > + int ret; > > + > > + info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL); > > + if (!info) > > + return -ENOMEM; > > + > > + info->dev = &i2c->dev; > > + > > + usbc_i2c = devm_i2c_new_dummy_device(&i2c->dev, i2c->adapter, > > + MT6370_USBC_I2CADDR); > > + if (IS_ERR(usbc_i2c)) > > + return dev_err_probe(&i2c->dev, PTR_ERR(usbc_i2c), > > + "Failed to register USBC I2C client\n"); > > + > > + /* Assign I2C client for PMU and TypeC */ > > + info->i2c[MT6370_PMU_I2C] = i2c; > > + info->i2c[MT6370_USBC_I2C] = usbc_i2c; > > + > > + info->regmap = devm_regmap_init(&i2c->dev, &mt6370_regmap_bus, info, > > + &mt6370_regmap_config); > > Apart from in mt6370_check_vendor_info() where is this actually used? Well... from my understanding, we use this MFD driver to make other drivers of MT6370 (e.g. charger, ADC, led...) use the same regmap settings. Thus, this regmap is not only used in mt6370_check_vendor_info(). > > > + if (IS_ERR(info->regmap)) > > + return dev_err_probe(&i2c->dev, PTR_ERR(info->regmap), > > + "Failed to register regmap\n"); > > + > > + ret = mt6370_check_vendor_info(info); > > + if (ret) > > + return dev_err_probe(&i2c->dev, ret, > > + "Failed to check vendor info\n"); > > + > > + ret = devm_regmap_add_irq_chip(&i2c->dev, info->regmap, i2c->irq, > > + IRQF_ONESHOT, -1, &mt6370_irq_chip, > > + &info->irq_data); > > + if (ret) > > + return dev_err_probe(&i2c->dev, ret, > > + "Failed to add irq chip\n"); > > + > > + return devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, > > + mt6370_devices, ARRAY_SIZE(mt6370_devices), > > + NULL, 0, > > + regmap_irq_get_domain(info->irq_data)); > > +} > > + > > +static const struct of_device_id mt6370_match_table[] = { > > + { .compatible = "mediatek,mt6370", }, > > + {} > > +}; > > +MODULE_DEVICE_TABLE(of, mt6370_match_table); > > + > > +static struct i2c_driver mt6370_driver = { > > + .driver = { > > + .name = "mt6370", > > + .of_match_table = mt6370_match_table, > > + }, > > + .probe_new = mt6370_probe, > > +}; > > +module_i2c_driver(mt6370_driver); > > + > > +MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>"); > > +MODULE_DESCRIPTION("MT6370 I2C Driver"); > > This is not an I2C driver. > > > +MODULE_LICENSE("GPL v2"); > > -- > Lee Jones [李琼斯] > Principal Technical Lead - Developer Services > Linaro.org │ Open source software for Arm SoCs > Follow Linaro: Facebook | Twitter | Blog Best regards, ChiaEn Wu
On Wed, 13 Jul 2022, ChiaEn Wu wrote: > Hi Lee, > > Thanks for your reply. > > Lee Jones <lee.jones@linaro.org> 於 2022年7月12日 週二 晚上11:29寫道： > > > > On Thu, 23 Jun 2022, ChiaEn Wu wrote: > > > > > From: ChiYuan Huang <cy_huang@richtek.com> > > > > > > Add Mediatek MT6370 MFD support. > > > > No such thing as "MFD support". > > > > And you're not getting away with submitting a 370 line patch with a 5 > > word change log either. :) > > > > Please at least tell us what the device is and what it's used for. > > I sincerely apologize. > We will add more descriptions of the MT6370 feature in the v5 patch. > > > > > > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > > > --- > > > > > > v3 > > > - Refine Kconfig help text > > > - Refine error message of unknown vendor ID in > > > mt6370_check_vendor_info() > > > - Refine return value handling of mt6370_regmap_read() > > > - Refine all probe error by using dev_err_probe() > > > - Refine "bank_idx" and "bank_addr" in mt6370_regmap_read() and > > > mt6370_regmap_write() > > > - Add "#define VENID*" and drop the comments in > > > mt6370_check_vendor_info() > > > - Drop "MFD" in MODULE_DESCRIPTION() > > > --- > > > drivers/mfd/Kconfig | 13 ++ > > > drivers/mfd/Makefile | 1 + > > > drivers/mfd/mt6370.c | 358 +++++++++++++++++++++++++++++++++++++++++++++++++++ > > > 3 files changed, 372 insertions(+) > > > create mode 100644 drivers/mfd/mt6370.c [...] > > > +static int mt6370_probe(struct i2c_client *i2c) > > > +{ > > > + struct mt6370_info *info; > > > + struct i2c_client *usbc_i2c; > > > + int ret; > > > + > > > + info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL); > > > + if (!info) > > > + return -ENOMEM; > > > + > > > + info->dev = &i2c->dev; > > > + > > > + usbc_i2c = devm_i2c_new_dummy_device(&i2c->dev, i2c->adapter, > > > + MT6370_USBC_I2CADDR); > > > + if (IS_ERR(usbc_i2c)) > > > + return dev_err_probe(&i2c->dev, PTR_ERR(usbc_i2c), > > > + "Failed to register USBC I2C client\n"); > > > + > > > + /* Assign I2C client for PMU and TypeC */ > > > + info->i2c[MT6370_PMU_I2C] = i2c; > > > + info->i2c[MT6370_USBC_I2C] = usbc_i2c; > > > + > > > + info->regmap = devm_regmap_init(&i2c->dev, &mt6370_regmap_bus, info, > > > + &mt6370_regmap_config); > > > > Apart from in mt6370_check_vendor_info() where is this actually used? > > Well... from my understanding, we use this MFD driver to make other > drivers of MT6370 (e.g. charger, ADC, led...) use the same regmap > settings. > Thus, this regmap is not only used in mt6370_check_vendor_info(). Well for that to happen you need to store the data somewhere for the child devices to fetch from. I don't see that happening in this patch? What did I miss?
Hi Lee, Lee Jones <lee.jones@linaro.org> 於 2022年7月13日 週三 下午4:04寫道： > > On Wed, 13 Jul 2022, ChiaEn Wu wrote: > > > Hi Lee, > > > > Thanks for your reply. > > > > Lee Jones <lee.jones@linaro.org> 於 2022年7月12日 週二 晚上11:29寫道： > > > > > > On Thu, 23 Jun 2022, ChiaEn Wu wrote: > > > > > > > From: ChiYuan Huang <cy_huang@richtek.com> > > > > > > > > Add Mediatek MT6370 MFD support. > > > > > > No such thing as "MFD support". > > > > > > And you're not getting away with submitting a 370 line patch with a 5 > > > word change log either. :) > > > > > > Please at least tell us what the device is and what it's used for. > > > > I sincerely apologize. > > We will add more descriptions of the MT6370 feature in the v5 patch. > > > > > > > > > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > > > > --- > > > > > > > > v3 > > > > - Refine Kconfig help text > > > > - Refine error message of unknown vendor ID in > > > > mt6370_check_vendor_info() > > > > - Refine return value handling of mt6370_regmap_read() > > > > - Refine all probe error by using dev_err_probe() > > > > - Refine "bank_idx" and "bank_addr" in mt6370_regmap_read() and > > > > mt6370_regmap_write() > > > > - Add "#define VENID*" and drop the comments in > > > > mt6370_check_vendor_info() > > > > - Drop "MFD" in MODULE_DESCRIPTION() > > > > --- > > > > drivers/mfd/Kconfig | 13 ++ > > > > drivers/mfd/Makefile | 1 + > > > > drivers/mfd/mt6370.c | 358 +++++++++++++++++++++++++++++++++++++++++++++++++++ > > > > 3 files changed, 372 insertions(+) > > > > create mode 100644 drivers/mfd/mt6370.c > > [...] > > > > > +static const struct mfd_cell mt6370_devices[] = { > > > > + MFD_CELL_OF("adc", NULL, NULL, 0, 0, "mediatek,mt6370-adc"), > > > > + MFD_CELL_OF("charger", NULL, NULL, 0, 0, "mediatek,mt6370-charger"), > > > > + MFD_CELL_OF("backlight", NULL, NULL, 0, 0, "mediatek,mt6370-backlight"), > > > > + MFD_CELL_OF("flashlight", NULL, NULL, 0, 0, "mediatek,mt6370-flashlight"), > > > > + MFD_CELL_OF("indicator", NULL, NULL, 0, 0, "mediatek,mt6370-indicator"), > > > > + MFD_CELL_OF("tcpc", NULL, NULL, 0, 0, "mediatek,mt6370-tcpc"), > > > > + MFD_CELL_RES("regulator", mt6370_regulator_irqs) > > > > > > The first parameters here should be prepended with something, perhaps > > > "mt6370_"? > > > OK, we will add the prefix in the next patch. Sorry, I forgot to ask a question in the last mail. I wonder if using "mt6370-xxx" (dash) is better than using "mt6370_" (underline) ?? Thanks. > [...] > > > > > +static int mt6370_probe(struct i2c_client *i2c) > > > > +{ > > > > + struct mt6370_info *info; > > > > + struct i2c_client *usbc_i2c; > > > > + int ret; > > > > + > > > > + info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL); > > > > + if (!info) > > > > + return -ENOMEM; > > > > + > > > > + info->dev = &i2c->dev; > > > > + > > > > + usbc_i2c = devm_i2c_new_dummy_device(&i2c->dev, i2c->adapter, > > > > + MT6370_USBC_I2CADDR); > > > > + if (IS_ERR(usbc_i2c)) > > > > + return dev_err_probe(&i2c->dev, PTR_ERR(usbc_i2c), > > > > + "Failed to register USBC I2C client\n"); > > > > + > > > > + /* Assign I2C client for PMU and TypeC */ > > > > + info->i2c[MT6370_PMU_I2C] = i2c; > > > > + info->i2c[MT6370_USBC_I2C] = usbc_i2c; > > > > + > > > > + info->regmap = devm_regmap_init(&i2c->dev, &mt6370_regmap_bus, info, > > > > + &mt6370_regmap_config); > > > > > > Apart from in mt6370_check_vendor_info() where is this actually used? > > > > Well... from my understanding, we use this MFD driver to make other > > drivers of MT6370 (e.g. charger, ADC, led...) use the same regmap > > settings. > > Thus, this regmap is not only used in mt6370_check_vendor_info(). > > Well for that to happen you need to store the data somewhere for the > child devices to fetch from. I don't see that happening in this > patch? What did I miss? hmmm... I got your point... I will let regmap be a local var in probe() in the next patch. Thank you so much! > > -- > Lee Jones [李琼斯] > Principal Technical Lead - Developer Services > Linaro.org │ Open source software for Arm SoCs > Follow Linaro: Facebook | Twitter | Blog Best regards, ChiaEn Wu
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 3b59456..4c900c4 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -937,6 +937,19 @@ config MFD_MT6360 PMIC part includes 2-channel BUCKs and 2-channel LDOs LDO part includes 4-channel LDOs +config MFD_MT6370 + tristate "Mediatek MT6370 SubPMIC" + select MFD_CORE + select REGMAP_I2C + select REGMAP_IRQ + depends on I2C + help + Say Y here to enable MT6370 SubPMIC functional support. + It consists of a single cell battery charger with ADC monitoring, RGB + LEDs, dual channel flashlight, WLED backlight driver, display bias + voltage supply, one general purpose LDO, and the USB Type-C & PD + controller complies with the latest USB Type-C and PD standards. + config MFD_MT6397 tristate "MediaTek MT6397 PMIC Support" select MFD_CORE diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 858cacf..62b2712 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -242,6 +242,7 @@ obj-$(CONFIG_INTEL_SOC_PMIC_BXTWC) += intel_soc_pmic_bxtwc.o obj-$(CONFIG_INTEL_SOC_PMIC_CHTWC) += intel_soc_pmic_chtwc.o obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI) += intel_soc_pmic_chtdc_ti.o obj-$(CONFIG_MFD_MT6360) += mt6360-core.o +obj-$(CONFIG_MFD_MT6370) += mt6370.o mt6397-objs := mt6397-core.o mt6397-irq.o mt6358-irq.o obj-$(CONFIG_MFD_MT6397) += mt6397.o obj-$(CONFIG_INTEL_SOC_PMIC_MRFLD) += intel_soc_pmic_mrfld.o diff --git a/drivers/mfd/mt6370.c b/drivers/mfd/mt6370.c new file mode 100644 index 0000000..49f02b1 --- /dev/null +++ b/drivers/mfd/mt6370.c @@ -0,0 +1,358 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <linux/bits.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/core.h> +#include <linux/module.h> +#include <linux/regmap.h> + +enum { + MT6370_USBC_I2C = 0, + MT6370_PMU_I2C, + MT6370_MAX_I2C +}; + +#define MT6370_REG_DEV_INFO 0x100 +#define MT6370_REG_CHG_IRQ1 0x1C0 +#define MT6370_REG_CHG_MASK1 0x1E0 + +#define MT6370_VENID_MASK GENMASK(7, 4) + +#define MT6370_NUM_IRQREGS 16 +#define MT6370_USBC_I2CADDR 0x4E +#define MT6370_REG_ADDRLEN 2 +#define MT6370_REG_MAXADDR 0x1FF + +#define MT6370_VENID_RT5081 0x8 +#define MT6370_VENID_RT5081A 0xA +#define MT6370_VENID_MT6370 0xE +#define MT6370_VENID_MT6371 0xF +#define MT6370_VENID_MT6372P 0x9 +#define MT6370_VENID_MT6372CP 0xB + +/* IRQ definitions */ +#define MT6370_IRQ_DIRCHGON 0 +#define MT6370_IRQ_CHG_TREG 4 +#define MT6370_IRQ_CHG_AICR 5 +#define MT6370_IRQ_CHG_MIVR 6 +#define MT6370_IRQ_PWR_RDY 7 +#define MT6370_IRQ_FL_CHG_VINOVP 11 +#define MT6370_IRQ_CHG_VSYSUV 12 +#define MT6370_IRQ_CHG_VSYSOV 13 +#define MT6370_IRQ_CHG_VBATOV 14 +#define MT6370_IRQ_CHG_VINOVPCHG 15 +#define MT6370_IRQ_TS_BAT_COLD 20 +#define MT6370_IRQ_TS_BAT_COOL 21 +#define MT6370_IRQ_TS_BAT_WARM 22 +#define MT6370_IRQ_TS_BAT_HOT 23 +#define MT6370_IRQ_TS_STATC 24 +#define MT6370_IRQ_CHG_FAULT 25 +#define MT6370_IRQ_CHG_STATC 26 +#define MT6370_IRQ_CHG_TMR 27 +#define MT6370_IRQ_CHG_BATABS 28 +#define MT6370_IRQ_CHG_ADPBAD 29 +#define MT6370_IRQ_CHG_RVP 30 +#define MT6370_IRQ_TSHUTDOWN 31 +#define MT6370_IRQ_CHG_IINMEAS 32 +#define MT6370_IRQ_CHG_ICCMEAS 33 +#define MT6370_IRQ_CHGDET_DONE 34 +#define MT6370_IRQ_WDTMR 35 +#define MT6370_IRQ_SSFINISH 36 +#define MT6370_IRQ_CHG_RECHG 37 +#define MT6370_IRQ_CHG_TERM 38 +#define MT6370_IRQ_CHG_IEOC 39 +#define MT6370_IRQ_ADC_DONE 40 +#define MT6370_IRQ_PUMPX_DONE 41 +#define MT6370_IRQ_BST_BATUV 45 +#define MT6370_IRQ_BST_MIDOV 46 +#define MT6370_IRQ_BST_OLP 47 +#define MT6370_IRQ_ATTACH 48 +#define MT6370_IRQ_DETACH 49 +#define MT6370_IRQ_HVDCP_STPDONE 51 +#define MT6370_IRQ_HVDCP_VBUSDET_DONE 52 +#define MT6370_IRQ_HVDCP_DET 53 +#define MT6370_IRQ_CHGDET 54 +#define MT6370_IRQ_DCDT 55 +#define MT6370_IRQ_DIRCHG_VGOK 59 +#define MT6370_IRQ_DIRCHG_WDTMR 60 +#define MT6370_IRQ_DIRCHG_UC 61 +#define MT6370_IRQ_DIRCHG_OC 62 +#define MT6370_IRQ_DIRCHG_OV 63 +#define MT6370_IRQ_OVPCTRL_SWON 67 +#define MT6370_IRQ_OVPCTRL_UVP_D 68 +#define MT6370_IRQ_OVPCTRL_UVP 69 +#define MT6370_IRQ_OVPCTRL_OVP_D 70 +#define MT6370_IRQ_OVPCTRL_OVP 71 +#define MT6370_IRQ_FLED_STRBPIN 72 +#define MT6370_IRQ_FLED_TORPIN 73 +#define MT6370_IRQ_FLED_TX 74 +#define MT6370_IRQ_FLED_LVF 75 +#define MT6370_IRQ_FLED2_SHORT 78 +#define MT6370_IRQ_FLED1_SHORT 79 +#define MT6370_IRQ_FLED2_STRB 80 +#define MT6370_IRQ_FLED1_STRB 81 +#define mT6370_IRQ_FLED2_STRB_TO 82 +#define MT6370_IRQ_FLED1_STRB_TO 83 +#define MT6370_IRQ_FLED2_TOR 84 +#define MT6370_IRQ_FLED1_TOR 85 +#define MT6370_IRQ_OTP 93 +#define MT6370_IRQ_VDDA_OVP 94 +#define MT6370_IRQ_VDDA_UV 95 +#define MT6370_IRQ_LDO_OC 103 +#define MT6370_IRQ_BLED_OCP 118 +#define MT6370_IRQ_BLED_OVP 119 +#define MT6370_IRQ_DSV_VNEG_OCP 123 +#define MT6370_IRQ_DSV_VPOS_OCP 124 +#define MT6370_IRQ_DSV_BST_OCP 125 +#define MT6370_IRQ_DSV_VNEG_SCP 126 +#define MT6370_IRQ_DSV_VPOS_SCP 127 + +struct mt6370_info { + struct i2c_client *i2c[MT6370_MAX_I2C]; + struct device *dev; + struct regmap *regmap; + struct regmap_irq_chip_data *irq_data; +}; + +static const struct regmap_irq mt6370_irqs[] = { + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHGON, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TREG, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_AICR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_MIVR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PWR_RDY, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FL_CHG_VINOVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSUV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VSYSOV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VBATOV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_VINOVPCHG, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COLD, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_COOL, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_WARM, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_BAT_HOT, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TS_STATC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_FAULT, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_STATC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TMR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_BATABS, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ADPBAD, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_TSHUTDOWN, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IINMEAS, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_ICCMEAS, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET_DONE, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_WDTMR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_SSFINISH, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_RECHG, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_TERM, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHG_IEOC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ADC_DONE, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_PUMPX_DONE, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_BATUV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_MIDOV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BST_OLP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_ATTACH, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DETACH, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_STPDONE, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_VBUSDET_DONE, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_HVDCP_DET, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_CHGDET, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DCDT, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_VGOK, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_WDTMR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_UC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DIRCHG_OV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_SWON, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP_D, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_UVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP_D, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OVPCTRL_OVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_STRBPIN, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TORPIN, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_TX, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED_LVF, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_SHORT, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_SHORT, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_STRB, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB, 8), + REGMAP_IRQ_REG_LINE(mT6370_IRQ_FLED2_STRB_TO, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_STRB_TO, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED2_TOR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_FLED1_TOR, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_OTP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_OVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_VDDA_UV, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_LDO_OC, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OCP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_BLED_OVP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_OCP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_OCP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_BST_OCP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VNEG_SCP, 8), + REGMAP_IRQ_REG_LINE(MT6370_IRQ_DSV_VPOS_SCP, 8) +}; + +static const struct regmap_irq_chip mt6370_irq_chip = { + .name = "mt6370-irqs", + .status_base = MT6370_REG_CHG_IRQ1, + .mask_base = MT6370_REG_CHG_MASK1, + .num_regs = MT6370_NUM_IRQREGS, + .irqs = mt6370_irqs, + .num_irqs = ARRAY_SIZE(mt6370_irqs), +}; + +static const struct resource mt6370_regulator_irqs[] = { + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_SCP, "db_vpos_scp"), + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_SCP, "db_vneg_scp"), + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_BST_OCP, "db_vbst_ocp"), + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VPOS_OCP, "db_vpos_ocp"), + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_DSV_VNEG_OCP, "db_vneg_ocp"), + DEFINE_RES_IRQ_NAMED(MT6370_IRQ_LDO_OC, "ldo_oc") +}; + +static const struct mfd_cell mt6370_devices[] = { + MFD_CELL_OF("adc", NULL, NULL, 0, 0, "mediatek,mt6370-adc"), + MFD_CELL_OF("charger", NULL, NULL, 0, 0, "mediatek,mt6370-charger"), + MFD_CELL_OF("backlight", NULL, NULL, 0, 0, "mediatek,mt6370-backlight"), + MFD_CELL_OF("flashlight", NULL, NULL, 0, 0, "mediatek,mt6370-flashlight"), + MFD_CELL_OF("indicator", NULL, NULL, 0, 0, "mediatek,mt6370-indicator"), + MFD_CELL_OF("tcpc", NULL, NULL, 0, 0, "mediatek,mt6370-tcpc"), + MFD_CELL_RES("regulator", mt6370_regulator_irqs) +}; + +static int mt6370_check_vendor_info(struct mt6370_info *info) +{ + unsigned int devinfo; + int ret; + + ret = regmap_read(info->regmap, MT6370_REG_DEV_INFO, &devinfo); + if (ret) + return ret; + + switch (FIELD_GET(MT6370_VENID_MASK, devinfo)) { + case MT6370_VENID_RT5081: + case MT6370_VENID_RT5081A: + case MT6370_VENID_MT6370: + case MT6370_VENID_MT6371: + case MT6370_VENID_MT6372P: + case MT6370_VENID_MT6372CP: + break; + default: + dev_err(info->dev, "Unknown Vendor ID 0x%02x\n", devinfo); + return -ENODEV; + } + + return 0; +} + +static int mt6370_regmap_read(void *context, const void *reg_buf, + size_t reg_size, void *val_buf, size_t val_size) +{ + struct mt6370_info *info = context; + u8 bank_idx, bank_addr; + int ret; + + bank_idx = *(u8 *)reg_buf; + bank_addr = *(u8 *)(reg_buf + 1); + + ret = i2c_smbus_read_i2c_block_data(info->i2c[bank_idx], bank_addr, + val_size, val_buf); + if (ret < 0) + return ret; + else if (ret != val_size) + return -EIO; + + return 0; +} + +static int mt6370_regmap_write(void *context, const void *data, size_t count) +{ + struct mt6370_info *info = context; + u8 bank_idx, bank_addr; + int len = count - MT6370_REG_ADDRLEN; + + bank_idx = *(u8 *)data; + bank_addr = *(u8 *)(data + 1); + + return i2c_smbus_write_i2c_block_data(info->i2c[bank_idx], bank_addr, + len, data + MT6370_REG_ADDRLEN); +} + +static const struct regmap_bus mt6370_regmap_bus = { + .read = mt6370_regmap_read, + .write = mt6370_regmap_write, +}; + +static const struct regmap_config mt6370_regmap_config = { + .reg_bits = 16, + .val_bits = 8, + .reg_format_endian = REGMAP_ENDIAN_BIG, + .max_register = MT6370_REG_MAXADDR, +}; + +static int mt6370_probe(struct i2c_client *i2c) +{ + struct mt6370_info *info; + struct i2c_client *usbc_i2c; + int ret; + + info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->dev = &i2c->dev; + + usbc_i2c = devm_i2c_new_dummy_device(&i2c->dev, i2c->adapter, + MT6370_USBC_I2CADDR); + if (IS_ERR(usbc_i2c)) + return dev_err_probe(&i2c->dev, PTR_ERR(usbc_i2c), + "Failed to register USBC I2C client\n"); + + /* Assign I2C client for PMU and TypeC */ + info->i2c[MT6370_PMU_I2C] = i2c; + info->i2c[MT6370_USBC_I2C] = usbc_i2c; + + info->regmap = devm_regmap_init(&i2c->dev, &mt6370_regmap_bus, info, + &mt6370_regmap_config); + if (IS_ERR(info->regmap)) + return dev_err_probe(&i2c->dev, PTR_ERR(info->regmap), + "Failed to register regmap\n"); + + ret = mt6370_check_vendor_info(info); + if (ret) + return dev_err_probe(&i2c->dev, ret, + "Failed to check vendor info\n"); + + ret = devm_regmap_add_irq_chip(&i2c->dev, info->regmap, i2c->irq, + IRQF_ONESHOT, -1, &mt6370_irq_chip, + &info->irq_data); + if (ret) + return dev_err_probe(&i2c->dev, ret, + "Failed to add irq chip\n"); + + return devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, + mt6370_devices, ARRAY_SIZE(mt6370_devices), + NULL, 0, + regmap_irq_get_domain(info->irq_data)); +} + +static const struct of_device_id mt6370_match_table[] = { + { .compatible = "mediatek,mt6370", }, + {} +}; +MODULE_DEVICE_TABLE(of, mt6370_match_table); + +static struct i2c_driver mt6370_driver = { + .driver = { + .name = "mt6370", + .of_match_table = mt6370_match_table, + }, + .probe_new = mt6370_probe, +}; +module_i2c_driver(mt6370_driver); + +MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>"); +MODULE_DESCRIPTION("MT6370 I2C Driver"); +MODULE_LICENSE("GPL v2");