| Message ID | 20231016215123.30343-4-laurent.pinchart@ideasonboard.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: mediatek: Add device tree for MT8365-based Pumpkin i350 | expand |
On 16/10/2023 23:51, Laurent Pinchart wrote: > Add a minimal device tree for the Genio i350 Pumpkin development board, > which is based on a MediaTek MT8365. > > The device tree is based on an initial version by Fabien Parent Based > written against the MediaTek BSP kernel ([1]). It has been cleaned up, > some features have been added (GPIO LEDs, ethernet), and some features > removed (audio, camera, display and dual-role USB). Those features will > be added back once the corresponding DT bindings and/or drivers become > available in the upstream kernel. > > [1] https://gitlab.com/mediatek/aiot/bsp/linux/-/blob/mtk-v5.15-dev/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > Co-developed-by: Fabien Parent <fparent@baylibre.com> > Signed-off-by: Fabien Parent <fparent@baylibre.com> > Co-developed-by: Paul Elder <paul.elder@ideasonboard.com> > Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > Changes compared to the BSP version: > > - Add ethernet controller > - Add GPIO LEDs > - Add reserved memory region for BL31 > - Update board model and compatible > - Rename enable-sdio-wakeup to wakeup-source > - Drop audio support > - Drop display support > - Drop dual role USB support > - Don't use underscores in node names > - Normalize pinmux node names > - Remove unneeded labels > - Drop unneeded always-on > - Drop unused pinmux nodes > - Drop camera GPIO hog > - Update copyright > - Fix formatting > - Sort alphabetically > --- > arch/arm64/boot/dts/mediatek/Makefile | 1 + > .../boot/dts/mediatek/mt8365-pumpkin.dts | 542 ++++++++++++++++++ > 2 files changed, 543 insertions(+) > create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > index c99c3372a4b5..bbc232bdadc4 100644 > --- a/arch/arm64/boot/dts/mediatek/Makefile > +++ b/arch/arm64/boot/dts/mediatek/Makefile > @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb > diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > new file mode 100644 > index 000000000000..88fa5d19c627 > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > @@ -0,0 +1,542 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2021 BayLibre, SAS. > + * Copyright (c) 2023 Ideas on Board Oy > + * > + * Author: Fabien Parent <fparent@baylibre.com> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> > + > +#include "mt8365.dtsi" > +#include "mt6357.dtsi" > + > +/ { > + model = "OLogic Pumpkin i350 EVK"; > + compatible = "ologic,pumpkin-i350", "mediatek,mt8365"; > + > + aliases { > + ethernet0 = ðernet_usb; > + mmc0 = &mmc0; > + mmc1 = &mmc1; > + mmc2 = &mmc2; Are mmc aliases needed ? > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:921600n8"; > + }; > + > + firmware { > + optee { > + compatible = "linaro,optee-tz"; > + method = "smc"; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-red { > + gpios = <&gpio_exp 12 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_RED>; > + function = LED_FUNCTION_HEARTBEAT; > + linux,default-trigger = "heartbeat"; > + }; > + > + led-green { > + gpios = <&gpio_exp 13 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_GREEN>; > + default-state = "off"; > + }; > + }; > + > + memory@40000000 { > + device_type = "memory"; > + reg = <0 0x40000000 0 0x80000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ > + secmon@43000000 { > + no-map; > + reg = <0 0x43000000 0 0x30000>; > + }; > + > + /* > + * 12 MiB reserved for OP-TEE (BL32) > + * +-----------------------+ 0x43e0_0000 > + * | SHMEM 2MiB | > + * +-----------------------+ 0x43c0_0000 > + * | | TA_RAM 8MiB | > + * + TZDRAM +--------------+ 0x4340_0000 > + * | | TEE_RAM 2MiB | > + * +-----------------------+ 0x4320_0000 > + */ > + optee@43200000 { > + no-map; > + reg = <0 0x43200000 0 0x00c00000>; > + }; > + }; > + > + usb_otg_vbus: usb-otg-vbus-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&pio 25 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > +}; > + > +&cpu0 { > + proc-supply = <&mt6357_vproc_reg>; > + sram-supply = <&mt6357_vsram_proc_reg>; > +}; > + > +&cpu1 { > + proc-supply = <&mt6357_vproc_reg>; > + sram-supply = <&mt6357_vsram_proc_reg>; > +}; > + > +&cpu2 { > + proc-supply = <&mt6357_vproc_reg>; > + sram-supply = <&mt6357_vsram_proc_reg>; > +}; > + > +&cpu3 { > + proc-supply = <&mt6357_vproc_reg>; > + sram-supply = <&mt6357_vsram_proc_reg>; > +}; > + > +&i2c0 { > + status = "okay" > + > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + > + clock-frequency = <100000>; Property order: - clock - pinctrl - status Actually, status should be at the end. Apply this for the other nodes please. > +}; > + > +&i2c1 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + > + clock-frequency = <100000 > + > + gpio_exp: gpio@20 { > + compatible = "ti,tca6416"; > + reg = <0x20>; > + reset-gpios = <&pio 78 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&tca6416_pins>; > + > + gpio-controller; > + #gpio-cells = <2>; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins>; > + > + clock-frequency = <100000>; > +}; > + > +&i2c3 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c3_pins>; > + > + clock-frequency = <100000>; > +}; > + > +&keypad { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&keypad_pins>; > + > + keypad,num-rows = <2>; > + keypad,num-columns = <1>; > + mediatek,debounce-us = <32000>; > + mediatek,double-keys; > + > + linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN) > + MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>; > +}; > + > +/* eMMC */ > +&mmc0 { > + status = "okay"; > + > + pinctrl-names = "default", "state_uhs"; > + pinctrl-0 = <&mmc0_pins_default>; > + pinctrl-1 = <&mmc0_pins_uhs>; > + > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > + > + bus-width = <8>; > + max-frequency = <200000000>; > + > + vmmc-supply = <&mt6357_vemc_reg>; > + vqmmc-supply = <&mt6357_vio18_reg>; > + > + cap-mmc-highspeed; > + cap-mmc-hw-reset; > + hs400-ds-delay = <0x12012>; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > + no-sd; > + no-sdio; > + non-removable; That's how it should be ordered: bus-width = <8>; max-frequency = <200000000>; cap-mmc-highspeed; cap-mmc-hw-reset; hs400-ds-delay = <0x12012>; mmc-hs200-1_8v; mmc-hs400-1_8v; no-sd; no-sdio; non-removable; vmmc-supply = ... vqmmc-supply = ... pinctrl-0 ... pinctrl-1 ... pinctrl-names ... status = "okay"; Apply this for other node please. > +}; > + > +/* SD card connector */ > +&mmc1 { > + status = "okay"; > + > + pinctrl-names = "default", "state_uhs"; > + pinctrl-0 = <&mmc1_pins_default>; > + pinctrl-1 = <&mmc1_pins_uhs>; > + > + bus-width = <4>; > + max-frequency = <200000000>; > + > + vmmc-supply = <&mt6357_vmch_reg>; > + vqmmc-supply = <&mt6357_vmc_reg>; > + > + cap-sd-highspeed; > + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; > + sd-uhs-sdr104; > + sd-uhs-sdr50; > +}; > + > +/* WiFi module */ > +&mmc2 { > + status = "okay"; > + > + pinctrl-names = "default", "state_uhs"; > + pinctrl-0 = <&mmc2_pins_default>; > + pinctrl-1 = <&mmc2_pins_uhs>; > + > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_2_SEL>; > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > + > + bus-width = <4>; > + max-frequency = <200000000>; > + > + vmmc-supply = <&mt6357_vemc_reg>; > + vqmmc-supply = <&mt6357_vio18_reg>; > + > + cap-sd-highspeed; > + cap-sdio-irq; > + wakeup-source; > + hs400-ds-delay = <0x12012>; > + keep-power-in-suspend; > + non-removable; > + sd-uhs-sdr104; > + sd-uhs-sdr25; > + sd-uhs-sdr50; > +}; > + > +&mt6357_pmic { > + interrupt-parent = <&pio>; > + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <2>; > +}; > + > +&pio { > + i2c0_pins: i2c0-pins { > + pins { > + pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>, > + <MT8365_PIN_58_SCL0__FUNC_SCL0_0>; > + mediatek,pull-up-adv = <3>; > + mediatek,drive-strength-adv = <00>; > + bias-pull-up; > + }; > + }; > + > + > + i2c1_pins: i2c1-pins { > + pins { > + pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, > + <MT8365_PIN_60_SCL1__FUNC_SCL1_0>; > + mediatek,pull-up-adv = <3>; > + mediatek,drive-strength-adv = <00>; > + bias-pull-up; > + }; > + }; > + > + i2c2_pins: i2c2-pins { > + pins { > + pinmux = <MT8365_PIN_61_SDA2__FUNC_SDA2_0>, > + <MT8365_PIN_62_SCL2__FUNC_SCL2_0>; > + mediatek,pull-up-adv = <3>; > + mediatek,drive-strength-adv = <00>; > + bias-pull-up; > + }; > + }; > + > + i2c3_pins: i2c3-pins { > + pins { > + pinmux = <MT8365_PIN_63_SDA3__FUNC_SDA3_0>, > + <MT8365_PIN_64_SCL3__FUNC_SCL3_0>; > + mediatek,pull-up-adv = <3>; > + mediatek,drive-strength-adv = <00>; > + bias-pull-up; > + }; > + }; > + > + keypad_pins: keypad-pins { > + pins { > + pinmux = <MT8365_PIN_22_KPROW0__FUNC_KPROW0>, > + <MT8365_PIN_23_KPROW1__FUNC_KPROW1>, > + <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>; > + }; > + }; > + > + mmc0_pins_default: mmc0-default-pins { > + clk-pins { > + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; > + bias-pull-down; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, > + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, > + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, > + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, > + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, > + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, > + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, > + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, > + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; > + input-enable; > + bias-pull-up; > + }; > + > + rst-pins { > + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; > + bias-pull-up; > + }; > + }; > + > + mmc0_pins_uhs: mmc0-uhs-pins{ > + clk-pins { > + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; > + drive-strength = <MTK_DRIVE_10mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, > + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, > + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, > + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, > + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, > + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, > + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, > + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, > + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; > + input-enable; > + drive-strength = <MTK_DRIVE_10mA>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > + }; > + > + ds-pins { > + pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>; > + drive-strength = <MTK_DRIVE_10mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + rst-pins { > + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; > + drive-strength = <MTK_DRIVE_10mA>; > + bias-pull-up; > + }; > + }; > + > + mmc1_pins_default: mmc1-default-pins { > + cd-pins { > + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; > + bias-pull-up; > + }; > + > + clk-pins { > + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, > + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, > + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, > + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, > + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; > + input-enable; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > + }; > + }; > + > + mmc1_pins_uhs: mmc1-uhs-pins { > + cd-pins { > + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; > + bias-pull-up; > + }; > + > + clk-pins { > + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; > + drive-strength = <MTK_DRIVE_8mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, > + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, > + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, > + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, > + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; > + input-enable; > + drive-strength = <MTK_DRIVE_6mA>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > + }; > + }; > + > + mmc2_pins_default: mmc2-default-pins { > + clk-pins { > + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; > + drive-strength = <MTK_DRIVE_4mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, > + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, > + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, > + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, > + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; > + input-enable; > + drive-strength = <MTK_DRIVE_4mA>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > + }; > + > + sysrstb-en-pins { > + pinmux = <MT8365_PIN_74_CMDAT6__FUNC_GPIO74>; > + output-low; > + }; > + }; > + > + mmc2_pins_uhs: mmc2-uhs-pins { > + clk-pins { > + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; > + drive-strength = <MTK_DRIVE_8mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + cmd-dat-pins { > + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, > + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, > + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, > + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, > + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; > + input-enable; > + drive-strength = <MTK_DRIVE_8mA>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > + }; > + > + ds-pins { > + pinmux = <MT8365_PIN_86_MSDC2_DSL__FUNC_MSDC2_DSL>; > + drive-strength = <MTK_DRIVE_8mA>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > + }; > + > + sysrstb-en-pins { > + pinmux = <MT8365_PIN_126_DMIC3_CLK__FUNC_GPIO126>; > + output-high; > + }; > + }; > + > + tca6416_pins: tca6416-pins { > + rst-n-pins { > + pinmux = <MT8365_PIN_78_CMHSYNC__FUNC_GPIO78>; > + output-high; > + }; > + > + int-n-pins { > + pinmux = <MT8365_PIN_79_CMVSYNC__FUNC_GPIO79>; > + input-enable; > + bias-pull-up; > + }; > + }; > + > + usb_pins: usb-pins { > + hub-rst-pins { > + pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>; > + output-low; > + }; > + > + id-pins { > + pinmux = <MT8365_PIN_39_URXD2__FUNC_GPIO39>; > + input-enable; > + bias-pull-up; > + }; > + > + vbus-pins { > + pinmux = <MT8365_PIN_25_KPCOL1__FUNC_USB_DRVVBUS>; > + }; > + }; > +}; > + > +&ssusb { > + status = "okay"; > + > + pinctrl-0 = <&usb_pins>; > + pinctrl-names = "default"; > + > + /* Host mode only for now, TUSB322 support is missing. */ > + dr_mode = "host"; > + maximum-speed = "high-speed"; > + vusb33-supply = <&mt6357_vusb33_reg>; Re-order please. > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +&usb_host { > + status = "okay"; > + > + vusb33-supply = <&mt6357_vusb33_reg>; > + > + #address-cells = <1>; > + #size-cells = <0>; Order: #address-cells = <1>; #size-cells = <0>; vusb33-supply = <&mt6357_vusb33_reg>; status = "okay"; > + > + hub@2 { > + reg = <2>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethernet_usb: ethernet@1 { > + compatible = "usb424,ec00"; > + reg = <1>; > + }; > + }; > +};
Hi Alexandre, On Thu, Oct 19, 2023 at 02:45:36PM +0200, Alexandre Mergnat wrote: > On 16/10/2023 23:51, Laurent Pinchart wrote: > > Add a minimal device tree for the Genio i350 Pumpkin development board, > > which is based on a MediaTek MT8365. > > > > The device tree is based on an initial version by Fabien Parent Based > > written against the MediaTek BSP kernel ([1]). It has been cleaned up, > > some features have been added (GPIO LEDs, ethernet), and some features > > removed (audio, camera, display and dual-role USB). Those features will > > be added back once the corresponding DT bindings and/or drivers become > > available in the upstream kernel. > > > > [1] https://gitlab.com/mediatek/aiot/bsp/linux/-/blob/mtk-v5.15-dev/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > > > Co-developed-by: Fabien Parent <fparent@baylibre.com> > > Signed-off-by: Fabien Parent <fparent@baylibre.com> > > Co-developed-by: Paul Elder <paul.elder@ideasonboard.com> > > Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> > > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > --- > > Changes compared to the BSP version: > > > > - Add ethernet controller > > - Add GPIO LEDs > > - Add reserved memory region for BL31 > > - Update board model and compatible > > - Rename enable-sdio-wakeup to wakeup-source > > - Drop audio support > > - Drop display support > > - Drop dual role USB support > > - Don't use underscores in node names > > - Normalize pinmux node names > > - Remove unneeded labels > > - Drop unneeded always-on > > - Drop unused pinmux nodes > > - Drop camera GPIO hog > > - Update copyright > > - Fix formatting > > - Sort alphabetically > > --- > > arch/arm64/boot/dts/mediatek/Makefile | 1 + > > .../boot/dts/mediatek/mt8365-pumpkin.dts | 542 ++++++++++++++++++ > > 2 files changed, 543 insertions(+) > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > > index c99c3372a4b5..bbc232bdadc4 100644 > > --- a/arch/arm64/boot/dts/mediatek/Makefile > > +++ b/arch/arm64/boot/dts/mediatek/Makefile > > @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb > > diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > new file mode 100644 > > index 000000000000..88fa5d19c627 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > @@ -0,0 +1,542 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (c) 2021 BayLibre, SAS. > > + * Copyright (c) 2023 Ideas on Board Oy > > + * > > + * Author: Fabien Parent <fparent@baylibre.com> > > + */ > > + > > +/dts-v1/; > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/leds/common.h> > > +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> > > + > > +#include "mt8365.dtsi" > > +#include "mt6357.dtsi" > > + > > +/ { > > + model = "OLogic Pumpkin i350 EVK"; > > + compatible = "ologic,pumpkin-i350", "mediatek,mt8365"; > > + > > + aliases { > > + ethernet0 = ðernet_usb; > > + mmc0 = &mmc0; > > + mmc1 = &mmc1; > > + mmc2 = &mmc2; > > Are mmc aliases needed ? Likely not. For mmc2, I don't think so. For mmc0 and mmc1, aliases provide a fixed ordering that helps differentiating between the eMMC and the external SD card. I don't mind dropping them if that's preferred. > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:921600n8"; > > + }; > > + > > + firmware { > > + optee { > > + compatible = "linaro,optee-tz"; > > + method = "smc"; > > + }; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led-red { > > + gpios = <&gpio_exp 12 GPIO_ACTIVE_HIGH>; > > + color = <LED_COLOR_ID_RED>; > > + function = LED_FUNCTION_HEARTBEAT; > > + linux,default-trigger = "heartbeat"; > > + }; > > + > > + led-green { > > + gpios = <&gpio_exp 13 GPIO_ACTIVE_HIGH>; > > + color = <LED_COLOR_ID_GREEN>; > > + default-state = "off"; > > + }; > > + }; > > + > > + memory@40000000 { > > + device_type = "memory"; > > + reg = <0 0x40000000 0 0x80000000>; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ > > + secmon@43000000 { > > + no-map; > > + reg = <0 0x43000000 0 0x30000>; > > + }; > > + > > + /* > > + * 12 MiB reserved for OP-TEE (BL32) > > + * +-----------------------+ 0x43e0_0000 > > + * | SHMEM 2MiB | > > + * +-----------------------+ 0x43c0_0000 > > + * | | TA_RAM 8MiB | > > + * + TZDRAM +--------------+ 0x4340_0000 > > + * | | TEE_RAM 2MiB | > > + * +-----------------------+ 0x4320_0000 > > + */ > > + optee@43200000 { > > + no-map; > > + reg = <0 0x43200000 0 0x00c00000>; > > + }; > > + }; > > + > > + usb_otg_vbus: usb-otg-vbus-regulator { > > + compatible = "regulator-fixed"; > > + regulator-name = "otg_vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + gpio = <&pio 25 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > +}; > > + > > +&cpu0 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu1 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu2 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu3 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&i2c0 { > > + status = "okay" > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c0_pins>; > > + > > + clock-frequency = <100000>; > > Property order: > - clock > - pinctrl > - status > > Actually, status should be at the end. > Apply this for the other nodes please. OK, I'll reorder properties. Is there a document that clearly states the preferred order ? > > +}; > > + > > +&i2c1 { > > + status = "okay"; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins>; > > + > > + clock-frequency = <100000 > + > > + gpio_exp: gpio@20 { > > + compatible = "ti,tca6416"; > > + reg = <0x20>; > > + reset-gpios = <&pio 78 GPIO_ACTIVE_LOW>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&tca6416_pins>; > > + > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > +}; > > + > > +&i2c2 { > > + status = "okay"; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins>; > > + > > + clock-frequency = <100000>; > > +}; > > + > > +&i2c3 { > > + status = "okay"; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c3_pins>; > > + > > + clock-frequency = <100000>; > > +}; > > + > > +&keypad { > > + status = "okay"; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&keypad_pins>; > > + > > + keypad,num-rows = <2>; > > + keypad,num-columns = <1>; > > + mediatek,debounce-us = <32000>; > > + mediatek,double-keys; > > + > > + linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN) > > + MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>; > > +}; > > + > > +/* eMMC */ > > +&mmc0 { > > + status = "okay"; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc0_pins_default>; > > + pinctrl-1 = <&mmc0_pins_uhs>; > > + > > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; > > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > > + > > + bus-width = <8>; > > + max-frequency = <200000000>; > > + > > + vmmc-supply = <&mt6357_vemc_reg>; > > + vqmmc-supply = <&mt6357_vio18_reg>; > > + > > + cap-mmc-highspeed; > > + cap-mmc-hw-reset; > > + hs400-ds-delay = <0x12012>; > > + mmc-hs200-1_8v; > > + mmc-hs400-1_8v; > > + no-sd; > > + no-sdio; > > + non-removable; > > That's how it should be ordered: > bus-width = <8>; > max-frequency = <200000000>; > > cap-mmc-highspeed; > cap-mmc-hw-reset; > hs400-ds-delay = <0x12012>; > mmc-hs200-1_8v; > mmc-hs400-1_8v; > no-sd; > no-sdio; > non-removable; > > vmmc-supply = ... > vqmmc-supply = ... > > pinctrl-0 ... > pinctrl-1 ... > pinctrl-names ... > > status = "okay"; > > Apply this for other node please. > > > +}; > > + > > +/* SD card connector */ > > +&mmc1 { > > + status = "okay"; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc1_pins_default>; > > + pinctrl-1 = <&mmc1_pins_uhs>; > > + > > + bus-width = <4>; > > + max-frequency = <200000000>; > > + > > + vmmc-supply = <&mt6357_vmch_reg>; > > + vqmmc-supply = <&mt6357_vmc_reg>; > > + > > + cap-sd-highspeed; > > + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; > > + sd-uhs-sdr104; > > + sd-uhs-sdr50; > > +}; > > + > > +/* WiFi module */ > > +&mmc2 { > > + status = "okay"; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc2_pins_default>; > > + pinctrl-1 = <&mmc2_pins_uhs>; > > + > > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_2_SEL>; > > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > > + > > + bus-width = <4>; > > + max-frequency = <200000000>; > > + > > + vmmc-supply = <&mt6357_vemc_reg>; > > + vqmmc-supply = <&mt6357_vio18_reg>; > > + > > + cap-sd-highspeed; > > + cap-sdio-irq; > > + wakeup-source; > > + hs400-ds-delay = <0x12012>; > > + keep-power-in-suspend; > > + non-removable; > > + sd-uhs-sdr104; > > + sd-uhs-sdr25; > > + sd-uhs-sdr50; > > +}; > > + > > +&mt6357_pmic { > > + interrupt-parent = <&pio>; > > + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > +}; > > + > > +&pio { > > + i2c0_pins: i2c0-pins { > > + pins { > > + pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>, > > + <MT8365_PIN_58_SCL0__FUNC_SCL0_0>; > > + mediatek,pull-up-adv = <3>; > > + mediatek,drive-strength-adv = <00>; > > + bias-pull-up; > > + }; > > + }; > > + > > + > > + i2c1_pins: i2c1-pins { > > + pins { > > + pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, > > + <MT8365_PIN_60_SCL1__FUNC_SCL1_0>; > > + mediatek,pull-up-adv = <3>; > > + mediatek,drive-strength-adv = <00>; > > + bias-pull-up; > > + }; > > + }; > > + > > + i2c2_pins: i2c2-pins { > > + pins { > > + pinmux = <MT8365_PIN_61_SDA2__FUNC_SDA2_0>, > > + <MT8365_PIN_62_SCL2__FUNC_SCL2_0>; > > + mediatek,pull-up-adv = <3>; > > + mediatek,drive-strength-adv = <00>; > > + bias-pull-up; > > + }; > > + }; > > + > > + i2c3_pins: i2c3-pins { > > + pins { > > + pinmux = <MT8365_PIN_63_SDA3__FUNC_SDA3_0>, > > + <MT8365_PIN_64_SCL3__FUNC_SCL3_0>; > > + mediatek,pull-up-adv = <3>; > > + mediatek,drive-strength-adv = <00>; > > + bias-pull-up; > > + }; > > + }; > > + > > + keypad_pins: keypad-pins { > > + pins { > > + pinmux = <MT8365_PIN_22_KPROW0__FUNC_KPROW0>, > > + <MT8365_PIN_23_KPROW1__FUNC_KPROW1>, > > + <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>; > > + }; > > + }; > > + > > + mmc0_pins_default: mmc0-default-pins { > > + clk-pins { > > + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; > > + bias-pull-down; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, > > + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, > > + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, > > + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, > > + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, > > + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, > > + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, > > + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, > > + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; > > + input-enable; > > + bias-pull-up; > > + }; > > + > > + rst-pins { > > + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; > > + bias-pull-up; > > + }; > > + }; > > + > > + mmc0_pins_uhs: mmc0-uhs-pins{ > > + clk-pins { > > + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, > > + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, > > + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, > > + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, > > + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, > > + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, > > + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, > > + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, > > + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; > > + input-enable; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + > > + ds-pins { > > + pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + rst-pins { > > + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-up; > > + }; > > + }; > > + > > + mmc1_pins_default: mmc1-default-pins { > > + cd-pins { > > + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; > > + bias-pull-up; > > + }; > > + > > + clk-pins { > > + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, > > + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, > > + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, > > + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, > > + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; > > + input-enable; > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + }; > > + > > + mmc1_pins_uhs: mmc1-uhs-pins { > > + cd-pins { > > + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; > > + bias-pull-up; > > + }; > > + > > + clk-pins { > > + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; > > + drive-strength = <MTK_DRIVE_8mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, > > + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, > > + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, > > + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, > > + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; > > + input-enable; > > + drive-strength = <MTK_DRIVE_6mA>; > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + }; > > + > > + mmc2_pins_default: mmc2-default-pins { > > + clk-pins { > > + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; > > + drive-strength = <MTK_DRIVE_4mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, > > + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, > > + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, > > + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, > > + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; > > + input-enable; > > + drive-strength = <MTK_DRIVE_4mA>; > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + > > + sysrstb-en-pins { > > + pinmux = <MT8365_PIN_74_CMDAT6__FUNC_GPIO74>; > > + output-low; > > + }; > > + }; > > + > > + mmc2_pins_uhs: mmc2-uhs-pins { > > + clk-pins { > > + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; > > + drive-strength = <MTK_DRIVE_8mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, > > + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, > > + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, > > + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, > > + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; > > + input-enable; > > + drive-strength = <MTK_DRIVE_8mA>; > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + > > + ds-pins { > > + pinmux = <MT8365_PIN_86_MSDC2_DSL__FUNC_MSDC2_DSL>; > > + drive-strength = <MTK_DRIVE_8mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + sysrstb-en-pins { > > + pinmux = <MT8365_PIN_126_DMIC3_CLK__FUNC_GPIO126>; > > + output-high; > > + }; > > + }; > > + > > + tca6416_pins: tca6416-pins { > > + rst-n-pins { > > + pinmux = <MT8365_PIN_78_CMHSYNC__FUNC_GPIO78>; > > + output-high; > > + }; > > + > > + int-n-pins { > > + pinmux = <MT8365_PIN_79_CMVSYNC__FUNC_GPIO79>; > > + input-enable; > > + bias-pull-up; > > + }; > > + }; > > + > > + usb_pins: usb-pins { > > + hub-rst-pins { > > + pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>; > > + output-low; > > + }; > > + > > + id-pins { > > + pinmux = <MT8365_PIN_39_URXD2__FUNC_GPIO39>; > > + input-enable; > > + bias-pull-up; > > + }; > > + > > + vbus-pins { > > + pinmux = <MT8365_PIN_25_KPCOL1__FUNC_USB_DRVVBUS>; > > + }; > > + }; > > +}; > > + > > +&ssusb { > > + status = "okay"; > > + > > + pinctrl-0 = <&usb_pins>; > > + pinctrl-names = "default"; > > + > > + /* Host mode only for now, TUSB322 support is missing. */ > > + dr_mode = "host"; > > + maximum-speed = "high-speed"; > > + vusb33-supply = <&mt6357_vusb33_reg>; > > Re-order please. > > > +}; > > + > > +&uart0 { > > + status = "okay"; > > +}; > > + > > +&usb_host { > > + status = "okay"; > > + > > + vusb33-supply = <&mt6357_vusb33_reg>; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > Order: > #address-cells = <1>; > #size-cells = <0>; > > vusb33-supply = <&mt6357_vusb33_reg>; > status = "okay"; > > > > + > > + hub@2 { > > + reg = <2>; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + ethernet_usb: ethernet@1 { > > + compatible = "usb424,ec00"; > > + reg = <1>; > > + }; > > + }; > > +};
Il 19/10/23 14:45, Alexandre Mergnat ha scritto: > > > On 16/10/2023 23:51, Laurent Pinchart wrote: >> Add a minimal device tree for the Genio i350 Pumpkin development board, >> which is based on a MediaTek MT8365. >> >> The device tree is based on an initial version by Fabien Parent Based >> written against the MediaTek BSP kernel ([1]). It has been cleaned up, >> some features have been added (GPIO LEDs, ethernet), and some features >> removed (audio, camera, display and dual-role USB). Those features will >> be added back once the corresponding DT bindings and/or drivers become >> available in the upstream kernel. >> >> [1] >> https://gitlab.com/mediatek/aiot/bsp/linux/-/blob/mtk-v5.15-dev/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts >> >> Co-developed-by: Fabien Parent <fparent@baylibre.com> >> Signed-off-by: Fabien Parent <fparent@baylibre.com> >> Co-developed-by: Paul Elder <paul.elder@ideasonboard.com> >> Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> >> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> >> --- >> Changes compared to the BSP version: >> >> - Add ethernet controller >> - Add GPIO LEDs >> - Add reserved memory region for BL31 >> - Update board model and compatible >> - Rename enable-sdio-wakeup to wakeup-source >> - Drop audio support >> - Drop display support >> - Drop dual role USB support >> - Don't use underscores in node names >> - Normalize pinmux node names >> - Remove unneeded labels >> - Drop unneeded always-on >> - Drop unused pinmux nodes >> - Drop camera GPIO hog >> - Update copyright >> - Fix formatting >> - Sort alphabetically >> --- >> arch/arm64/boot/dts/mediatek/Makefile | 1 + >> .../boot/dts/mediatek/mt8365-pumpkin.dts | 542 ++++++++++++++++++ >> 2 files changed, 543 insertions(+) >> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts >> >> diff --git a/arch/arm64/boot/dts/mediatek/Makefile >> b/arch/arm64/boot/dts/mediatek/Makefile >> index c99c3372a4b5..bbc232bdadc4 100644 >> --- a/arch/arm64/boot/dts/mediatek/Makefile >> +++ b/arch/arm64/boot/dts/mediatek/Makefile >> @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb >> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts >> b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts >> new file mode 100644 >> index 000000000000..88fa5d19c627 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts >> @@ -0,0 +1,542 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (c) 2021 BayLibre, SAS. >> + * Copyright (c) 2023 Ideas on Board Oy >> + * >> + * Author: Fabien Parent <fparent@baylibre.com> >> + */ >> + >> +/dts-v1/; >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/leds/common.h> >> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> >> + >> +#include "mt8365.dtsi" >> +#include "mt6357.dtsi" >> + >> +/ { >> + model = "OLogic Pumpkin i350 EVK"; >> + compatible = "ologic,pumpkin-i350", "mediatek,mt8365"; >> + >> + aliases { >> + ethernet0 = ðernet_usb; >> + mmc0 = &mmc0; >> + mmc1 = &mmc1; >> + mmc2 = &mmc2; > > Are mmc aliases needed ? > This makes sure that, for example, the eMMC is always mmcblk0, and that a (micro)SD card always has mmcblk1. So yes, they are. Cheers, Angelo
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index c99c3372a4b5..bbc232bdadc4 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts new file mode 100644 index 000000000000..88fa5d19c627 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts @@ -0,0 +1,542 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2021 BayLibre, SAS. + * Copyright (c) 2023 Ideas on Board Oy + * + * Author: Fabien Parent <fparent@baylibre.com> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> + +#include "mt8365.dtsi" +#include "mt6357.dtsi" + +/ { + model = "OLogic Pumpkin i350 EVK"; + compatible = "ologic,pumpkin-i350", "mediatek,mt8365"; + + aliases { + ethernet0 = ðernet_usb; + mmc0 = &mmc0; + mmc1 = &mmc1; + mmc2 = &mmc2; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-red { + gpios = <&gpio_exp 12 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_HEARTBEAT; + linux,default-trigger = "heartbeat"; + }; + + led-green { + gpios = <&gpio_exp 13 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + default-state = "off"; + }; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x80000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ + secmon@43000000 { + no-map; + reg = <0 0x43000000 0 0x30000>; + }; + + /* + * 12 MiB reserved for OP-TEE (BL32) + * +-----------------------+ 0x43e0_0000 + * | SHMEM 2MiB | + * +-----------------------+ 0x43c0_0000 + * | | TA_RAM 8MiB | + * + TZDRAM +--------------+ 0x4340_0000 + * | | TEE_RAM 2MiB | + * +-----------------------+ 0x4320_0000 + */ + optee@43200000 { + no-map; + reg = <0 0x43200000 0 0x00c00000>; + }; + }; + + usb_otg_vbus: usb-otg-vbus-regulator { + compatible = "regulator-fixed"; + regulator-name = "otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 25 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&cpu0 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu1 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu2 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu3 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&i2c0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + clock-frequency = <100000>; +}; + +&i2c1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <100000>; + + gpio_exp: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + reset-gpios = <&pio 78 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&tca6416_pins>; + + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&i2c2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + +&i2c3 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + + clock-frequency = <100000>; +}; + +&keypad { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&keypad_pins>; + + keypad,num-rows = <2>; + keypad,num-columns = <1>; + mediatek,debounce-us = <32000>; + mediatek,double-keys; + + linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN) + MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>; +}; + +/* eMMC */ +&mmc0 { + status = "okay"; + + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; + + bus-width = <8>; + max-frequency = <200000000>; + + vmmc-supply = <&mt6357_vemc_reg>; + vqmmc-supply = <&mt6357_vio18_reg>; + + cap-mmc-highspeed; + cap-mmc-hw-reset; + hs400-ds-delay = <0x12012>; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + no-sd; + no-sdio; + non-removable; +}; + +/* SD card connector */ +&mmc1 { + status = "okay"; + + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + + bus-width = <4>; + max-frequency = <200000000>; + + vmmc-supply = <&mt6357_vmch_reg>; + vqmmc-supply = <&mt6357_vmc_reg>; + + cap-sd-highspeed; + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; + sd-uhs-sdr104; + sd-uhs-sdr50; +}; + +/* WiFi module */ +&mmc2 { + status = "okay"; + + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc2_pins_default>; + pinctrl-1 = <&mmc2_pins_uhs>; + + assigned-clocks = <&topckgen CLK_TOP_MSDC50_2_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; + + bus-width = <4>; + max-frequency = <200000000>; + + vmmc-supply = <&mt6357_vemc_reg>; + vqmmc-supply = <&mt6357_vio18_reg>; + + cap-sd-highspeed; + cap-sdio-irq; + wakeup-source; + hs400-ds-delay = <0x12012>; + keep-power-in-suspend; + non-removable; + sd-uhs-sdr104; + sd-uhs-sdr25; + sd-uhs-sdr50; +}; + +&mt6357_pmic { + interrupt-parent = <&pio>; + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +&pio { + i2c0_pins: i2c0-pins { + pins { + pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>, + <MT8365_PIN_58_SCL0__FUNC_SCL0_0>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + bias-pull-up; + }; + }; + + + i2c1_pins: i2c1-pins { + pins { + pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, + <MT8365_PIN_60_SCL1__FUNC_SCL1_0>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + bias-pull-up; + }; + }; + + i2c2_pins: i2c2-pins { + pins { + pinmux = <MT8365_PIN_61_SDA2__FUNC_SDA2_0>, + <MT8365_PIN_62_SCL2__FUNC_SCL2_0>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + bias-pull-up; + }; + }; + + i2c3_pins: i2c3-pins { + pins { + pinmux = <MT8365_PIN_63_SDA3__FUNC_SDA3_0>, + <MT8365_PIN_64_SCL3__FUNC_SCL3_0>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + bias-pull-up; + }; + }; + + keypad_pins: keypad-pins { + pins { + pinmux = <MT8365_PIN_22_KPROW0__FUNC_KPROW0>, + <MT8365_PIN_23_KPROW1__FUNC_KPROW1>, + <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>; + }; + }; + + mmc0_pins_default: mmc0-default-pins { + clk-pins { + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; + bias-pull-down; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; + input-enable; + bias-pull-up; + }; + + rst-pins { + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; + bias-pull-up; + }; + }; + + mmc0_pins_uhs: mmc0-uhs-pins{ + clk-pins { + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_10mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_10mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + ds-pins { + pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>; + drive-strength = <MTK_DRIVE_10mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + rst-pins { + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; + drive-strength = <MTK_DRIVE_10mA>; + bias-pull-up; + }; + }; + + mmc1_pins_default: mmc1-default-pins { + cd-pins { + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; + bias-pull-up; + }; + + clk-pins { + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; + input-enable; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc1_pins_uhs: mmc1-uhs-pins { + cd-pins { + pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; + bias-pull-up; + }; + + clk-pins { + pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, + <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, + <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, + <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, + <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_6mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + }; + + mmc2_pins_default: mmc2-default-pins { + clk-pins { + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_4mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + sysrstb-en-pins { + pinmux = <MT8365_PIN_74_CMDAT6__FUNC_GPIO74>; + output-low; + }; + }; + + mmc2_pins_uhs: mmc2-uhs-pins { + clk-pins { + pinmux = <MT8365_PIN_81_MSDC2_CLK__FUNC_MSDC2_CLK>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + cmd-dat-pins { + pinmux = <MT8365_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0>, + <MT8365_PIN_83_MSDC2_DAT1__FUNC_MSDC2_DAT1>, + <MT8365_PIN_84_MSDC2_DAT2__FUNC_MSDC2_DAT2>, + <MT8365_PIN_85_MSDC2_DAT3__FUNC_MSDC2_DAT3>, + <MT8365_PIN_80_MSDC2_CMD__FUNC_MSDC2_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + ds-pins { + pinmux = <MT8365_PIN_86_MSDC2_DSL__FUNC_MSDC2_DSL>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + sysrstb-en-pins { + pinmux = <MT8365_PIN_126_DMIC3_CLK__FUNC_GPIO126>; + output-high; + }; + }; + + tca6416_pins: tca6416-pins { + rst-n-pins { + pinmux = <MT8365_PIN_78_CMHSYNC__FUNC_GPIO78>; + output-high; + }; + + int-n-pins { + pinmux = <MT8365_PIN_79_CMVSYNC__FUNC_GPIO79>; + input-enable; + bias-pull-up; + }; + }; + + usb_pins: usb-pins { + hub-rst-pins { + pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>; + output-low; + }; + + id-pins { + pinmux = <MT8365_PIN_39_URXD2__FUNC_GPIO39>; + input-enable; + bias-pull-up; + }; + + vbus-pins { + pinmux = <MT8365_PIN_25_KPCOL1__FUNC_USB_DRVVBUS>; + }; + }; +}; + +&ssusb { + status = "okay"; + + pinctrl-0 = <&usb_pins>; + pinctrl-names = "default"; + + /* Host mode only for now, TUSB322 support is missing. */ + dr_mode = "host"; + maximum-speed = "high-speed"; + vusb33-supply = <&mt6357_vusb33_reg>; +}; + +&uart0 { + status = "okay"; +}; + +&usb_host { + status = "okay"; + + vusb33-supply = <&mt6357_vusb33_reg>; + + #address-cells = <1>; + #size-cells = <0>; + + hub@2 { + reg = <2>; + + #address-cells = <1>; + #size-cells = <0>; + + ethernet_usb: ethernet@1 { + compatible = "usb424,ec00"; + reg = <1>; + }; + }; +};