diff mbox series

[v2,18/18] arm64: dts: mediatek: add display support for mt8365-evk

Message ID 20231023-display-support-v2-18-33ce8864b227@baylibre.com (mailing list archive)
State New, archived
Headers show
Series Add display support for the MT8365-EVK board | expand

Commit Message

Alexandre Mergnat April 16, 2024, 3:53 p.m. UTC 
MIPI DSI:
- Add "vsys_lcm_reg" regulator support and setup the "mt6357_vsim1_reg",
to power the pannel plugged to the DSI connector.
- Setup the Display Parallel Interface.
  - Add the startek kd070fhfid015 pannel support.

HDMI:
- Add HDMI connector support.
- Add the "ite,it66121" HDMI bridge support, driven by I2C1.
- Setup the Display Parallel Interface.

Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
---
 arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 182 ++++++++++++++++++++++++++++
 1 file changed, 182 insertions(+)

Comments

AngeloGioacchino Del Regno April 17, 2024, 10:27 a.m. UTC | #1 
Il 16/04/24 17:53, Alexandre Mergnat ha scritto:
> MIPI DSI:
> - Add "vsys_lcm_reg" regulator support and setup the "mt6357_vsim1_reg",
> to power the pannel plugged to the DSI connector.
> - Setup the Display Parallel Interface.
>    - Add the startek kd070fhfid015 pannel support.
> 
> HDMI:
> - Add HDMI connector support.
> - Add the "ite,it66121" HDMI bridge support, driven by I2C1.
> - Setup the Display Parallel Interface.
> 
> Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
> ---
>   arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 182 ++++++++++++++++++++++++++++
>   1 file changed, 182 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> index 50cbaefa1a99..4afdcbefc481 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> @@ -26,6 +26,18 @@ chosen {
>   		stdout-path = "serial0:921600n8";
>   	};
>   
> +	connector {
> +		compatible = "hdmi-connector";
> +		label = "hdmi";
> +		type = "d";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&hdmi_connector_out>;
> +			};
> +		};
> +	};
> +
>   	firmware {
>   		optee {
>   			compatible = "linaro,optee-tz";
> @@ -86,6 +98,56 @@ optee_reserved: optee@43200000 {
>   			reg = <0 0x43200000 0 0x00c00000>;
>   		};
>   	};
> +
> +	vsys_lcm_reg: regulator-vsys-lcm {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&pio 129 GPIO_ACTIVE_HIGH>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-name = "vsys_lcm";
> +	};
> +};
> +
> +&dpi0 {
> +	pinctrl-0 = <&dpi_default_pins>;
> +	pinctrl-1 = <&dpi_idle_pins>;
> +	pinctrl-names = "default", "sleep";
> +	status = "okay";
> +
> +	port {
> +		dpi_out: endpoint {
> +			remote-endpoint = <&it66121_in>;
> +		};
> +	};
> +};
> +
> +&dsi0 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	panel@0 {
> +		compatible = "startek,kd070fhfid015";
> +		status = "okay";

status is always okay, unless it's disabled.

> +		reg = <0>;
> +		enable-gpios = <&pio 67 GPIO_ACTIVE_HIGH>;
> +		reset-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
> +		iovcc-supply = <&mt6357_vsim1_reg>;
> +		power-supply = <&vsys_lcm_reg>;
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&dsi_out>;
> +			};
> +		};
> +	};
> +
> +	port {
> +		dsi_out: endpoint {
> +			remote-endpoint = <&panel_in>;
> +		};
> +	};
>   };
>   
>   &cpu0 {
> @@ -138,6 +200,50 @@ &i2c0 {
>   	status = "okay";
>   };
>   
> +&i2c1 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-div = <2>;
> +	clock-frequency = <100000>;
> +	pinctrl-0 = <&i2c1_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	it66121hdmitx: it66121hdmitx@4c {

Can we please get an actually readable name for this node?

Just a suggestion (you're free to rename however you want)

	it66121_hdmi: hdmi@4c {

> +		#sound-dai-cells = <0>;
> +		compatible = "ite,it66121";
> +		interrupt-parent = <&pio>;
> +		interrupts = <68 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-0 = <&ite_pins>;
> +		pinctrl-names = "default";
> +		reg = <0x4c>;
> +		reset-gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> +		vcn18-supply = <&mt6357_vsim2_reg>;
> +		vcn33-supply = <&mt6357_vibr_reg>;
> +		vrf12-supply = <&mt6357_vrf12_reg>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				it66121_in: endpoint {
> +					bus-width = <12>;
> +					remote-endpoint = <&dpi_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				hdmi_connector_out: endpoint {
> +					remote-endpoint = <&hdmi_connector_in>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
>   &mmc0 {
>   	assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
>   	assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> @@ -180,7 +286,55 @@ &mt6357_pmic {
>   	#interrupt-cells = <2>;
>   };
>   
> +&mt6357_vsim1_reg {
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <1800000>;
> +};
> +
>   &pio {
> +	dpi_default_pins: dpi-default-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_0_GPIO0__FUNC_DPI_D0>,
> +				 <MT8365_PIN_1_GPIO1__FUNC_DPI_D1>,
> +				 <MT8365_PIN_2_GPIO2__FUNC_DPI_D2>,
> +				 <MT8365_PIN_3_GPIO3__FUNC_DPI_D3>,
> +				 <MT8365_PIN_4_GPIO4__FUNC_DPI_D4>,
> +				 <MT8365_PIN_5_GPIO5__FUNC_DPI_D5>,
> +				 <MT8365_PIN_6_GPIO6__FUNC_DPI_D6>,
> +				 <MT8365_PIN_7_GPIO7__FUNC_DPI_D7>,
> +				 <MT8365_PIN_8_GPIO8__FUNC_DPI_D8>,
> +				 <MT8365_PIN_9_GPIO9__FUNC_DPI_D9>,
> +				 <MT8365_PIN_10_GPIO10__FUNC_DPI_D10>,
> +				 <MT8365_PIN_11_GPIO11__FUNC_DPI_D11>,
> +				 <MT8365_PIN_12_GPIO12__FUNC_DPI_DE>,
> +				 <MT8365_PIN_13_GPIO13__FUNC_DPI_VSYNC>,
> +				 <MT8365_PIN_14_GPIO14__FUNC_DPI_CK>,
> +				 <MT8365_PIN_15_GPIO15__FUNC_DPI_HSYNC>;
> +			drive-strength = <MTK_DRIVE_4mA>;

drive-strength = <4> is just fine....! :-)

> +		};
> +	};
> +
> +	dpi_idle_pins: dpi-idle-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_0_GPIO0__FUNC_GPIO0>,
> +				 <MT8365_PIN_1_GPIO1__FUNC_GPIO1>,
> +				 <MT8365_PIN_2_GPIO2__FUNC_GPIO2>,
> +				 <MT8365_PIN_3_GPIO3__FUNC_GPIO3>,
> +				 <MT8365_PIN_4_GPIO4__FUNC_GPIO4>,
> +				 <MT8365_PIN_5_GPIO5__FUNC_GPIO5>,
> +				 <MT8365_PIN_6_GPIO6__FUNC_GPIO6>,
> +				 <MT8365_PIN_7_GPIO7__FUNC_GPIO7>,
> +				 <MT8365_PIN_8_GPIO8__FUNC_GPIO8>,
> +				 <MT8365_PIN_9_GPIO9__FUNC_GPIO9>,
> +				 <MT8365_PIN_10_GPIO10__FUNC_GPIO10>,
> +				 <MT8365_PIN_11_GPIO11__FUNC_GPIO11>,
> +				 <MT8365_PIN_12_GPIO12__FUNC_GPIO12>,
> +				 <MT8365_PIN_13_GPIO13__FUNC_GPIO13>,
> +				 <MT8365_PIN_14_GPIO14__FUNC_GPIO14>,
> +				 <MT8365_PIN_15_GPIO15__FUNC_GPIO15>;
> +		};
> +	};
> +
>   	ethernet_pins: ethernet-pins {
>   		phy_reset_pins {
>   			pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>;
> @@ -222,6 +376,34 @@ pins {
>   		};
>   	};
>   
> +	i2c1_pins: i2c1-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>,
> +				 <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
> +			bias-pull-up;
> +		};
> +	};
> +
> +	ite_pins: ite-pins {
> +

extra blank line, please remove.

> +		irq_ite_pins {

Did you run dtbs_check?!? :-)

Cheers,
Angelo

> +			pinmux = <MT8365_PIN_68_CMDAT0__FUNC_GPIO68>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		pwr_pins {
> +			pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>,
> +				 <MT8365_PIN_71_CMDAT3__FUNC_GPIO71>;
> +			output-high;
> +		};
> +
> +		rst_ite_pins {
> +			pinmux = <MT8365_PIN_69_CMDAT1__FUNC_GPIO69>;
> +			output-high;
> +		};
> +	};
> +
>   	mmc0_default_pins: mmc0-default-pins {
>   		clk-pins {
>   			pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;
>
Alexandre Mergnat April 18, 2024, 1:02 p.m. UTC | #2 
On 17/04/2024 12:27, AngeloGioacchino Del Regno wrote:
> 
>> +        irq_ite_pins {
> 
> Did you run dtbs_check?!? :-)

Yes without error, here my command:
dt-validate -s Documentation/devicetree/bindings arch/arm64/boot/dts/mediatek/mt8365-evk.dtb

Also I've done a "make dtbs_check" just to be sure, nothing wrong on mt8365-evk.dtb.

For you, what is the issue please ?
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
index 50cbaefa1a99..4afdcbefc481 100644
--- a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -26,6 +26,18 @@  chosen {
 		stdout-path = "serial0:921600n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "d";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_connector_out>;
+			};
+		};
+	};
+
 	firmware {
 		optee {
 			compatible = "linaro,optee-tz";
@@ -86,6 +98,56 @@  optee_reserved: optee@43200000 {
 			reg = <0 0x43200000 0 0x00c00000>;
 		};
 	};
+
+	vsys_lcm_reg: regulator-vsys-lcm {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&pio 129 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "vsys_lcm";
+	};
+};
+
+&dpi0 {
+	pinctrl-0 = <&dpi_default_pins>;
+	pinctrl-1 = <&dpi_idle_pins>;
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&it66121_in>;
+		};
+	};
+};
+
+&dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "startek,kd070fhfid015";
+		status = "okay";
+		reg = <0>;
+		enable-gpios = <&pio 67 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		iovcc-supply = <&mt6357_vsim1_reg>;
+		power-supply = <&vsys_lcm_reg>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+
+	port {
+		dsi_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &cpu0 {
@@ -138,6 +200,50 @@  &i2c0 {
 	status = "okay";
 };
 
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-div = <2>;
+	clock-frequency = <100000>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	it66121hdmitx: it66121hdmitx@4c {
+		#sound-dai-cells = <0>;
+		compatible = "ite,it66121";
+		interrupt-parent = <&pio>;
+		interrupts = <68 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&ite_pins>;
+		pinctrl-names = "default";
+		reg = <0x4c>;
+		reset-gpios = <&pio 69 GPIO_ACTIVE_LOW>;
+		vcn18-supply = <&mt6357_vsim2_reg>;
+		vcn33-supply = <&mt6357_vibr_reg>;
+		vrf12-supply = <&mt6357_vrf12_reg>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				it66121_in: endpoint {
+					bus-width = <12>;
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				hdmi_connector_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+};
+
 &mmc0 {
 	assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
 	assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
@@ -180,7 +286,55 @@  &mt6357_pmic {
 	#interrupt-cells = <2>;
 };
 
+&mt6357_vsim1_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
 &pio {
+	dpi_default_pins: dpi-default-pins {
+		pins {
+			pinmux = <MT8365_PIN_0_GPIO0__FUNC_DPI_D0>,
+				 <MT8365_PIN_1_GPIO1__FUNC_DPI_D1>,
+				 <MT8365_PIN_2_GPIO2__FUNC_DPI_D2>,
+				 <MT8365_PIN_3_GPIO3__FUNC_DPI_D3>,
+				 <MT8365_PIN_4_GPIO4__FUNC_DPI_D4>,
+				 <MT8365_PIN_5_GPIO5__FUNC_DPI_D5>,
+				 <MT8365_PIN_6_GPIO6__FUNC_DPI_D6>,
+				 <MT8365_PIN_7_GPIO7__FUNC_DPI_D7>,
+				 <MT8365_PIN_8_GPIO8__FUNC_DPI_D8>,
+				 <MT8365_PIN_9_GPIO9__FUNC_DPI_D9>,
+				 <MT8365_PIN_10_GPIO10__FUNC_DPI_D10>,
+				 <MT8365_PIN_11_GPIO11__FUNC_DPI_D11>,
+				 <MT8365_PIN_12_GPIO12__FUNC_DPI_DE>,
+				 <MT8365_PIN_13_GPIO13__FUNC_DPI_VSYNC>,
+				 <MT8365_PIN_14_GPIO14__FUNC_DPI_CK>,
+				 <MT8365_PIN_15_GPIO15__FUNC_DPI_HSYNC>;
+			drive-strength = <MTK_DRIVE_4mA>;
+		};
+	};
+
+	dpi_idle_pins: dpi-idle-pins {
+		pins {
+			pinmux = <MT8365_PIN_0_GPIO0__FUNC_GPIO0>,
+				 <MT8365_PIN_1_GPIO1__FUNC_GPIO1>,
+				 <MT8365_PIN_2_GPIO2__FUNC_GPIO2>,
+				 <MT8365_PIN_3_GPIO3__FUNC_GPIO3>,
+				 <MT8365_PIN_4_GPIO4__FUNC_GPIO4>,
+				 <MT8365_PIN_5_GPIO5__FUNC_GPIO5>,
+				 <MT8365_PIN_6_GPIO6__FUNC_GPIO6>,
+				 <MT8365_PIN_7_GPIO7__FUNC_GPIO7>,
+				 <MT8365_PIN_8_GPIO8__FUNC_GPIO8>,
+				 <MT8365_PIN_9_GPIO9__FUNC_GPIO9>,
+				 <MT8365_PIN_10_GPIO10__FUNC_GPIO10>,
+				 <MT8365_PIN_11_GPIO11__FUNC_GPIO11>,
+				 <MT8365_PIN_12_GPIO12__FUNC_GPIO12>,
+				 <MT8365_PIN_13_GPIO13__FUNC_GPIO13>,
+				 <MT8365_PIN_14_GPIO14__FUNC_GPIO14>,
+				 <MT8365_PIN_15_GPIO15__FUNC_GPIO15>;
+		};
+	};
+
 	ethernet_pins: ethernet-pins {
 		phy_reset_pins {
 			pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>;
@@ -222,6 +376,34 @@  pins {
 		};
 	};
 
+	i2c1_pins: i2c1-pins {
+		pins {
+			pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>,
+				 <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+			bias-pull-up;
+		};
+	};
+
+	ite_pins: ite-pins {
+
+		irq_ite_pins {
+			pinmux = <MT8365_PIN_68_CMDAT0__FUNC_GPIO68>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pwr_pins {
+			pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>,
+				 <MT8365_PIN_71_CMDAT3__FUNC_GPIO71>;
+			output-high;
+		};
+
+		rst_ite_pins {
+			pinmux = <MT8365_PIN_69_CMDAT1__FUNC_GPIO69>;
+			output-high;
+		};
+	};
+
 	mmc0_default_pins: mmc0-default-pins {
 		clk-pins {
 			pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;