diff mbox series

[net-next,v10,02/13] net: phy: mediatek: Fix spelling errors and rearrange variables

Message ID 20240701105417.19941-3-SkyLake.Huang@mediatek.com (mailing list archive)
State New
Headers show
Series net: phy: mediatek: Introduce mtk-phy-lib and add 2.5Gphy support | expand

Commit Message

SkyLake Huang (黃啟澤) July 1, 2024, 10:54 a.m. UTC
From: "SkyLake.Huang" <skylake.huang@mediatek.com>

This patch fixes spelling errors which comes from mediatek-ge-soc.c and
rearrange variables with reverse Xmas tree order.

Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
---
 drivers/net/phy/mediatek/mtk-ge-soc.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/phy/mediatek/mtk-ge-soc.c b/drivers/net/phy/mediatek/mtk-ge-soc.c
index f4f9412..0eb5395 100644
--- a/drivers/net/phy/mediatek/mtk-ge-soc.c
+++ b/drivers/net/phy/mediatek/mtk-ge-soc.c
@@ -408,16 +408,17 @@  static int tx_offset_cal_efuse(struct phy_device *phydev, u32 *buf)
 
 static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf)
 {
-	int i;
-	int bias[16] = {};
-	const int vals_9461[16] = { 7, 1, 4, 7,
-				    7, 1, 4, 7,
-				    7, 1, 4, 7,
-				    7, 1, 4, 7 };
 	const int vals_9481[16] = { 10, 6, 6, 10,
 				    10, 6, 6, 10,
 				    10, 6, 6, 10,
 				    10, 6, 6, 10 };
+	const int vals_9461[16] = { 7, 1, 4, 7,
+				    7, 1, 4, 7,
+				    7, 1, 4, 7,
+				    7, 1, 4, 7 };
+	int bias[16] = {};
+	int i;
+
 	switch (phydev->drv->phy_id) {
 	case MTK_GPHY_ID_MT7981:
 		/* We add some calibration to efuse values
@@ -1069,10 +1070,10 @@  static int start_cal(struct phy_device *phydev, enum CAL_ITEM cal_item,
 
 static int mt798x_phy_calibration(struct phy_device *phydev)
 {
+	struct nvmem_cell *cell;
 	int ret = 0;
-	u32 *buf;
 	size_t len;
-	struct nvmem_cell *cell;
+	u32 *buf;
 
 	cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data");
 	if (IS_ERR(cell)) {
@@ -1415,7 +1416,7 @@  static int mt7988_phy_probe_shared(struct phy_device *phydev)
 	 * LED_C and LED_D respectively. At the same time those pins are used to
 	 * bootstrap configuration of the reference clock source (LED_A),
 	 * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D).
-	 * In practise this is done using a LED and a resistor pulling the pin
+	 * In practice this is done using a LED and a resistor pulling the pin
 	 * either to GND or to VIO.
 	 * The detected value at boot time is accessible at run-time using the
 	 * TPBANK0 register located in the gpio base of the pinctrl, in order