| Message ID | 20241001093815.2481899-1-wenst@chromium.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Input: elan_i2c - Wait for initialization after enabling regulator supply | expand |
On Tue, Oct 01, 2024 at 05:38:14PM +0800, Chen-Yu Tsai wrote: > Elan trackpad controllers require some delay after enabling power to > the controller for the hardware and firmware to initialize: > > - 2ms for hardware initialization > - 100ms for firmware initialization > > Until then, the hardware will not respond to I2C transfers. This was > observed on the MT8173 Chromebooks after the regulator supply for the > trackpad was changed to "not always on". > > Add proper delays after regulator_enable() calls. > > Fixes: 6696777c6506 ("Input: add driver for Elan I2C/SMbus touchpad") > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> > --- > This will unfortunately slightly slow down the driver probe and resume. > An optimization would be to check if the regulator is enabled already, > and shorten or skip the delay if it is. This would require a new API > though. > --- > drivers/input/mouse/elan_i2c_core.c | 6 ++++++ > 1 file changed, 6 insertions(+) > > diff --git a/drivers/input/mouse/elan_i2c_core.c b/drivers/input/mouse/elan_i2c_core.c > index ce96513b34f6..89556f61004e 100644 > --- a/drivers/input/mouse/elan_i2c_core.c > +++ b/drivers/input/mouse/elan_i2c_core.c > @@ -46,6 +46,8 @@ > #define ETP_FWIDTH_REDUCE 90 > #define ETP_FINGER_WIDTH 15 > #define ETP_RETRY_COUNT 3 > +/* H/W init 2 ms + F/W init 100 ms w/ round up */ > +#define ETP_POWER_ON_DELAY 110 > > /* quirks to control the device */ > #define ETP_QUIRK_QUICK_WAKEUP BIT(0) > @@ -1237,6 +1239,8 @@ static int elan_probe(struct i2c_client *client) > return error; > } > > + msleep(ETP_POWER_ON_DELAY); > + > /* Make sure there is something at this address */ > error = i2c_smbus_read_byte(client); > if (error < 0) { > @@ -1374,6 +1378,8 @@ static int elan_resume(struct device *dev) > dev_err(dev, "error %d enabling regulator\n", error); > goto err; > } > + > + msleep(ETP_POWER_ON_DELAY); This will add an unwanted delay on ACPI systems that handle power sequencing in firmware. However use of "optional" regulators is frowned upon in this case as the supply in reality is not optional. Mark, has there been any developments that would help reconciling difference in behavior between ACPI and DT systems. Ideally we'd need to know when supply was turned on, and adjust the wait accordingly. Thanks.
On Tue, Oct 01, 2024 at 02:57:10AM -0700, Dmitry Torokhov wrote: > This will add an unwanted delay on ACPI systems that handle power > sequencing in firmware. However use of "optional" regulators is frowned > upon in this case as the supply in reality is not optional. > Mark, has there been any developments that would help reconciling > difference in behavior between ACPI and DT systems. Ideally we'd need to > know when supply was turned on, and adjust the wait accordingly. There's not been any changes here, but there's always been an event availalbe when a regulator is turned on? There's also no difference between DT and ACPI systems here, both could have the regulator fixed on and I'd certainly not want to rely on an ACPI system implementing a device specific delay after power on given the sort of stuff they like to put into machine specific drivers.
diff --git a/drivers/input/mouse/elan_i2c_core.c b/drivers/input/mouse/elan_i2c_core.c index ce96513b34f6..89556f61004e 100644 --- a/drivers/input/mouse/elan_i2c_core.c +++ b/drivers/input/mouse/elan_i2c_core.c @@ -46,6 +46,8 @@ #define ETP_FWIDTH_REDUCE 90 #define ETP_FINGER_WIDTH 15 #define ETP_RETRY_COUNT 3 +/* H/W init 2 ms + F/W init 100 ms w/ round up */ +#define ETP_POWER_ON_DELAY 110 /* quirks to control the device */ #define ETP_QUIRK_QUICK_WAKEUP BIT(0) @@ -1237,6 +1239,8 @@ static int elan_probe(struct i2c_client *client) return error; } + msleep(ETP_POWER_ON_DELAY); + /* Make sure there is something at this address */ error = i2c_smbus_read_byte(client); if (error < 0) { @@ -1374,6 +1378,8 @@ static int elan_resume(struct device *dev) dev_err(dev, "error %d enabling regulator\n", error); goto err; } + + msleep(ETP_POWER_ON_DELAY); } error = elan_set_power(data, true);
Elan trackpad controllers require some delay after enabling power to the controller for the hardware and firmware to initialize: - 2ms for hardware initialization - 100ms for firmware initialization Until then, the hardware will not respond to I2C transfers. This was observed on the MT8173 Chromebooks after the regulator supply for the trackpad was changed to "not always on". Add proper delays after regulator_enable() calls. Fixes: 6696777c6506 ("Input: add driver for Elan I2C/SMbus touchpad") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> --- This will unfortunately slightly slow down the driver probe and resume. An optimization would be to check if the regulator is enabled already, and shorten or skip the delay if it is. This would require a new API though. --- drivers/input/mouse/elan_i2c_core.c | 6 ++++++ 1 file changed, 6 insertions(+)