@@ -3287,9 +3287,8 @@ static int mv88e6xxx_setup_port(struct mv88e6xxx_chip *chip, int port)
{
struct device_node *phy_handle = NULL;
struct dsa_switch *ds = chip->ds;
- phy_interface_t mode;
struct dsa_port *dp;
- int tx_amp, speed;
+ int tx_amp;
int err;
u16 reg;
@@ -3298,40 +3297,10 @@ static int mv88e6xxx_setup_port(struct mv88e6xxx_chip *chip, int port)
dp = dsa_to_port(ds, port);
- /* MAC Forcing register: don't force link, speed, duplex or flow control
- * state to any particular values on physical ports, but force the CPU
- * port and all DSA ports to their maximum bandwidth and full duplex.
- */
- if (dsa_is_cpu_port(ds, port) || dsa_is_dsa_port(ds, port)) {
- unsigned long caps = dp->pl_config.mac_capabilities;
-
- if (chip->info->ops->port_max_speed_mode)
- mode = chip->info->ops->port_max_speed_mode(port);
- else
- mode = PHY_INTERFACE_MODE_NA;
-
- if (caps & MAC_10000FD)
- speed = SPEED_10000;
- else if (caps & MAC_5000FD)
- speed = SPEED_5000;
- else if (caps & MAC_2500FD)
- speed = SPEED_2500;
- else if (caps & MAC_1000)
- speed = SPEED_1000;
- else if (caps & MAC_100)
- speed = SPEED_100;
- else
- speed = SPEED_10;
-
- err = mv88e6xxx_port_setup_mac(chip, port, LINK_FORCED_UP,
- speed, DUPLEX_FULL,
- PAUSE_OFF, mode);
- } else {
- err = mv88e6xxx_port_setup_mac(chip, port, LINK_UNFORCED,
- SPEED_UNFORCED, DUPLEX_UNFORCED,
- PAUSE_ON,
- PHY_INTERFACE_MODE_NA);
- }
+ err = mv88e6xxx_port_setup_mac(chip, port, LINK_UNFORCED,
+ SPEED_UNFORCED, DUPLEX_UNFORCED,
+ PAUSE_ON,
+ PHY_INTERFACE_MODE_NA);
if (err)
return err;
@@ -1559,6 +1559,9 @@ int dsa_port_phylink_create(struct dsa_port *dp)
return PTR_ERR(dp->pl);
}
+ if (dp->type == DSA_PORT_TYPE_CPU || dp->type == DSA_PORT_TYPE_DSA)
+ phylink_set_max_fixed_link(dp->pl);
+
return 0;
}
@@ -1663,20 +1666,14 @@ static int dsa_port_phylink_register(struct dsa_port *dp)
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
- struct device_node *phy_np;
int port = dp->index;
if (!ds->ops->adjust_link) {
- phy_np = of_parse_phandle(dp->dn, "phy-handle", 0);
- if (of_phy_is_fixed_link(dp->dn) || phy_np) {
- if (ds->ops->phylink_mac_link_down)
- ds->ops->phylink_mac_link_down(ds, port,
- MLO_AN_FIXED, PHY_INTERFACE_MODE_NA);
- of_node_put(phy_np);
- return dsa_port_phylink_register(dp);
- }
- of_node_put(phy_np);
- return 0;
+ if (ds->ops->phylink_mac_link_down)
+ ds->ops->phylink_mac_link_down(ds, port,
+ MLO_AN_FIXED, PHY_INTERFACE_MODE_NA);
+
+ return dsa_port_phylink_register(dp);
}
dev_warn(ds->dev,
Currently, we only use phylink for CPU and DSA ports if there is a fixed-link specification, or a PHY specified. The reason for this behaviour is that when neither is specified, there was no way for phylink to know the link parameters. Now that we have phylink_set_max_link_speed() (which has become possible through the addition of mac_capabilities) we now have the ability to know the maximum link speed for a specific link, and can now use phylink for this case as well. However, we need DSA drivers to report the interface mode being used on these ports so that we can select a maximum speed appropriate for the interface mode that hardware may have configured for the port. This is especially important with the conversion of DSA drivers to phylink_pcs, as the PCS code only gets called if we are using phylink for the port. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> --- drivers/net/dsa/mv88e6xxx/chip.c | 41 ++++---------------------------- net/dsa/port.c | 19 +++++++-------- 2 files changed, 13 insertions(+), 47 deletions(-)