@@ -35,10 +35,16 @@ config NET_DSA_LANTIQ_GSWIP
the xrx200 / VR9 SoC.
config NET_DSA_MT7530
- tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
+ tristate "MediaTek Ethernet switch support"
select NET_DSA_TAG_MTK
select MEDIATEK_GE_PHY
select PCS_MTK_LYNXI
+ help
+ This enables support for the MediaTek Ethernet switch chips.
+
+config NET_DSA_MT7530_MDIO
+ tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
+ select NET_DSA_MT7530
help
This enables support for the MediaTek MT7530 and MT7531 Ethernet
switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
@@ -6,7 +6,8 @@ ifdef CONFIG_NET_DSA_LOOP
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o
endif
obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
-obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
+obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
+obj-$(CONFIG_NET_DSA_MT7530_MDIO) += mt7530-mdio.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
new file mode 100644
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/consumer.h>
+#include <linux/mdio.h>
+#include <linux/module.h>
+#include <linux/pcs/pcs-mtk-lynxi.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+
+#include "mt7530.h"
+
+static const struct of_device_id mt7530_of_match[] = {
+ { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
+ { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
+ { .compatible = "mediatek,mt7531", .data = &mt753x_table[ID_MT7531], },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mt7530_of_match);
+
+static int
+mt7530_probe(struct mdio_device *mdiodev)
+{
+ struct mt7530_priv *priv;
+ struct device_node *dn;
+
+ dn = mdiodev->dev.of_node;
+
+ priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
+ if (!priv->ds)
+ return -ENOMEM;
+
+ priv->ds->dev = &mdiodev->dev;
+ priv->ds->num_ports = MT7530_NUM_PORTS;
+
+ /* Use medatek,mcm property to distinguish hardware type that would
+ * casues a little bit differences on power-on sequence.
+ */
+ priv->mcm = of_property_read_bool(dn, "mediatek,mcm");
+ if (priv->mcm) {
+ dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n");
+
+ priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm");
+ if (IS_ERR(priv->rstc)) {
+ dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
+ return PTR_ERR(priv->rstc);
+ }
+ }
+
+ /* Get the hardware identifier from the devicetree node.
+ * We will need it for some of the clock and regulator setup.
+ */
+ priv->info = of_device_get_match_data(&mdiodev->dev);
+ if (!priv->info)
+ return -EINVAL;
+
+ /* Sanity check if these required device operations are filled
+ * properly.
+ */
+ if (!priv->info->sw_setup || !priv->info->pad_setup ||
+ !priv->info->phy_read_c22 || !priv->info->phy_write_c22 ||
+ !priv->info->mac_port_get_caps ||
+ !priv->info->mac_port_config)
+ return -EINVAL;
+
+ priv->id = priv->info->id;
+
+ if (priv->id == ID_MT7530) {
+ priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
+ if (IS_ERR(priv->core_pwr))
+ return PTR_ERR(priv->core_pwr);
+
+ priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io");
+ if (IS_ERR(priv->io_pwr))
+ return PTR_ERR(priv->io_pwr);
+ }
+
+ /* Not MCM that indicates switch works as the remote standalone
+ * integrated circuit so the GPIO pin would be used to complete
+ * the reset, otherwise memory-mapped register accessing used
+ * through syscon provides in the case of MCM.
+ */
+ if (!priv->mcm) {
+ priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(priv->reset)) {
+ dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
+ return PTR_ERR(priv->reset);
+ }
+ }
+
+ priv->bus = mdiodev->bus;
+ priv->dev = &mdiodev->dev;
+ priv->ds->priv = priv;
+ priv->ds->ops = &mt7530_switch_ops;
+ mutex_init(&priv->reg_mutex);
+ dev_set_drvdata(&mdiodev->dev, priv);
+
+ return dsa_register_switch(priv->ds);
+}
+
+static void
+mt7530_remove(struct mdio_device *mdiodev)
+{
+ struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
+ int ret = 0, i;
+
+ if (!priv)
+ return;
+
+ ret = regulator_disable(priv->core_pwr);
+ if (ret < 0)
+ dev_err(priv->dev,
+ "Failed to disable core power: %d\n", ret);
+
+ ret = regulator_disable(priv->io_pwr);
+ if (ret < 0)
+ dev_err(priv->dev, "Failed to disable io pwr: %d\n",
+ ret);
+
+ if (priv->irq)
+ mt7530_free_irq(priv);
+
+ dsa_unregister_switch(priv->ds);
+
+ for (i = 0; i < 2; ++i)
+ mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs);
+
+ mutex_destroy(&priv->reg_mutex);
+}
+
+static void mt7530_shutdown(struct mdio_device *mdiodev)
+{
+ struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
+
+ if (!priv)
+ return;
+
+ dsa_switch_shutdown(priv->ds);
+
+ dev_set_drvdata(&mdiodev->dev, NULL);
+}
+
+static struct mdio_driver mt7530_mdio_driver = {
+ .probe = mt7530_probe,
+ .remove = mt7530_remove,
+ .shutdown = mt7530_shutdown,
+ .mdiodrv.driver = {
+ .name = "mt7530",
+ .of_match_table = mt7530_of_match,
+ },
+};
+mdio_module_driver(mt7530_mdio_driver);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch (MDIO)");
+MODULE_LICENSE("GPL");
@@ -921,6 +921,24 @@ mt7530_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
return 0;
}
+static const char *p5_intf_modes(unsigned int p5_interface)
+{
+ switch (p5_interface) {
+ case P5_DISABLED:
+ return "DISABLED";
+ case P5_INTF_SEL_PHY_P0:
+ return "PHY P0";
+ case P5_INTF_SEL_PHY_P4:
+ return "PHY P4";
+ case P5_INTF_SEL_GMAC5:
+ return "GMAC5";
+ case P5_INTF_SEL_GMAC5_SGMII:
+ return "GMAC5_SGMII";
+ default:
+ return "unknown";
+ }
+}
+
static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
{
struct mt7530_priv *priv = ds->priv;
@@ -2067,12 +2085,13 @@ mt7530_free_irq_common(struct mt7530_priv *priv)
irq_domain_remove(priv->irq_domain);
}
-static void
+void
mt7530_free_irq(struct mt7530_priv *priv)
{
mt7530_free_mdio_irq(priv);
mt7530_free_irq_common(priv);
}
+EXPORT_SYMBOL_GPL(mt7530_free_irq);
static int
mt7530_setup_mdio(struct mt7530_priv *priv)
@@ -3010,7 +3029,7 @@ static int mt753x_set_mac_eee(struct dsa_switch *ds, int port,
return 0;
}
-static const struct dsa_switch_ops mt7530_switch_ops = {
+const struct dsa_switch_ops mt7530_switch_ops = {
.get_tag_protocol = mtk_get_tag_protocol,
.setup = mt753x_setup,
.get_strings = mt7530_get_strings,
@@ -3044,8 +3063,9 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
.get_mac_eee = mt753x_get_mac_eee,
.set_mac_eee = mt753x_set_mac_eee,
};
+EXPORT_SYMBOL_GPL(mt7530_switch_ops);
-static const struct mt753x_info mt753x_table[] = {
+const struct mt753x_info mt753x_table[] = {
[ID_MT7621] = {
.id = ID_MT7621,
.pcs_ops = &mt7530_pcs_ops,
@@ -3084,153 +3104,7 @@ static const struct mt753x_info mt753x_table[] = {
.mac_port_config = mt7531_mac_config,
},
};
-
-static const struct of_device_id mt7530_of_match[] = {
- { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
- { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
- { .compatible = "mediatek,mt7531", .data = &mt753x_table[ID_MT7531], },
- { /* sentinel */ },
-};
-MODULE_DEVICE_TABLE(of, mt7530_of_match);
-
-static int
-mt7530_probe(struct mdio_device *mdiodev)
-{
- struct mt7530_priv *priv;
- struct device_node *dn;
-
- dn = mdiodev->dev.of_node;
-
- priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
- if (!priv->ds)
- return -ENOMEM;
-
- priv->ds->dev = &mdiodev->dev;
- priv->ds->num_ports = MT7530_NUM_PORTS;
-
- /* Use medatek,mcm property to distinguish hardware type that would
- * casues a little bit differences on power-on sequence.
- */
- priv->mcm = of_property_read_bool(dn, "mediatek,mcm");
- if (priv->mcm) {
- dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n");
-
- priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm");
- if (IS_ERR(priv->rstc)) {
- dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
- return PTR_ERR(priv->rstc);
- }
- }
-
- /* Get the hardware identifier from the devicetree node.
- * We will need it for some of the clock and regulator setup.
- */
- priv->info = of_device_get_match_data(&mdiodev->dev);
- if (!priv->info)
- return -EINVAL;
-
- /* Sanity check if these required device operations are filled
- * properly.
- */
- if (!priv->info->sw_setup || !priv->info->pad_setup ||
- !priv->info->phy_read_c22 || !priv->info->phy_write_c22 ||
- !priv->info->mac_port_get_caps ||
- !priv->info->mac_port_config)
- return -EINVAL;
-
- priv->id = priv->info->id;
-
- if (priv->id == ID_MT7530) {
- priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
- if (IS_ERR(priv->core_pwr))
- return PTR_ERR(priv->core_pwr);
-
- priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io");
- if (IS_ERR(priv->io_pwr))
- return PTR_ERR(priv->io_pwr);
- }
-
- /* Not MCM that indicates switch works as the remote standalone
- * integrated circuit so the GPIO pin would be used to complete
- * the reset, otherwise memory-mapped register accessing used
- * through syscon provides in the case of MCM.
- */
- if (!priv->mcm) {
- priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
- GPIOD_OUT_LOW);
- if (IS_ERR(priv->reset)) {
- dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
- return PTR_ERR(priv->reset);
- }
- }
-
- priv->bus = mdiodev->bus;
- priv->dev = &mdiodev->dev;
- priv->ds->priv = priv;
- priv->ds->ops = &mt7530_switch_ops;
- mutex_init(&priv->reg_mutex);
- dev_set_drvdata(&mdiodev->dev, priv);
-
- return dsa_register_switch(priv->ds);
-}
-
-static void
-mt7530_remove(struct mdio_device *mdiodev)
-{
- struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
- int ret = 0, i;
-
- if (!priv)
- return;
-
- ret = regulator_disable(priv->core_pwr);
- if (ret < 0)
- dev_err(priv->dev,
- "Failed to disable core power: %d\n", ret);
-
- ret = regulator_disable(priv->io_pwr);
- if (ret < 0)
- dev_err(priv->dev, "Failed to disable io pwr: %d\n",
- ret);
-
- if (priv->irq)
- mt7530_free_irq(priv);
-
- dsa_unregister_switch(priv->ds);
-
- for (i = 0; i < 2; ++i)
- mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs);
-
- mutex_destroy(&priv->reg_mutex);
-}
-
-static void mt7530_shutdown(struct mdio_device *mdiodev)
-{
- struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
-
- if (!priv)
- return;
-
- dsa_switch_shutdown(priv->ds);
-
- dev_set_drvdata(&mdiodev->dev, NULL);
-}
-
-static struct mdio_driver mt7530_mdio_driver = {
- .probe = mt7530_probe,
- .remove = mt7530_remove,
- .shutdown = mt7530_shutdown,
- .mdiodrv.driver = {
- .name = "mt7530",
- .of_match_table = mt7530_of_match,
- },
-};
-
-mdio_module_driver(mt7530_mdio_driver);
+EXPORT_SYMBOL_GPL(mt753x_table);
MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch");
@@ -682,24 +682,6 @@ enum p5_interface_select {
P5_INTF_SEL_GMAC5_SGMII,
};
-static const char *p5_intf_modes(unsigned int p5_interface)
-{
- switch (p5_interface) {
- case P5_DISABLED:
- return "DISABLED";
- case P5_INTF_SEL_PHY_P0:
- return "PHY P0";
- case P5_INTF_SEL_PHY_P4:
- return "PHY P4";
- case P5_INTF_SEL_GMAC5:
- return "GMAC5";
- case P5_INTF_SEL_GMAC5_SGMII:
- return "GMAC5_SGMII";
- default:
- return "unknown";
- }
-}
-
struct mt7530_priv;
struct mt753x_pcs {
@@ -830,4 +812,9 @@ static inline void INIT_MT7530_DUMMY_POLL(struct mt7530_dummy_poll *p,
p->reg = reg;
}
+void mt7530_free_irq(struct mt7530_priv *priv);
+
+extern const struct dsa_switch_ops mt7530_switch_ops;
+extern const struct mt753x_info mt753x_table[];
+
#endif /* __MT7530_H */
In order to support the built-in switch of some MediaTek SoCs we need to use MMIO instead of MDIO to access the switch. Prepare this be splitting-off the part of the driver registering an MDIO driver, so we can add another module acting as MMIO/platform driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org> --- drivers/net/dsa/Kconfig | 8 +- drivers/net/dsa/Makefile | 3 +- drivers/net/dsa/mt7530-mdio.c | 165 ++++++++++++++++++++++++++++++++ drivers/net/dsa/mt7530.c | 174 +++++----------------------------- drivers/net/dsa/mt7530.h | 23 +---- 5 files changed, 203 insertions(+), 170 deletions(-) create mode 100644 drivers/net/dsa/mt7530-mdio.c