mbox series

[v2,0/7] Generic Command Line changes

Message ID 20210308235319.2988609-1-danielwa@cisco.com (mailing list archive)
Headers show
Series Generic Command Line changes | expand

Message

Daniel Walker (danielwa) March 8, 2021, 11:53 p.m. UTC 
This fixed some problem identified in my last release. I made updates
based on comments from Christophe Leroy.

I added scripted updates to the defconfig file for mips and powerpc.
This is required in order to maintain the status quo for those platforms
which used the prior builtin command line system.

These were tested on all effected architectures.

Daniel Walker (7):
  CMDLINE: add generic builtin command line
  CMDLINE: drivers: of: ifdef out cmdline section
  powerpc: convert config files to generic cmdline
  CMDLINE: powerpc: convert to generic builtin command line
  mips: convert config files to generic cmdline
  CMDLINE: mips: convert to generic builtin command line
  CMDLINE: x86: convert to generic builtin command line

 arch/mips/Kconfig                             |  4 +-
 arch/mips/Kconfig.debug                       | 44 ---------
 arch/mips/configs/ar7_defconfig               |  9 +-
 arch/mips/configs/bcm47xx_defconfig           |  8 +-
 arch/mips/configs/bcm63xx_defconfig           | 15 ++--
 arch/mips/configs/bmips_be_defconfig          | 11 +--
 arch/mips/configs/bmips_stb_defconfig         | 11 +--
 arch/mips/configs/capcella_defconfig          | 11 +--
 arch/mips/configs/ci20_defconfig              | 10 +--
 arch/mips/configs/cu1000-neo_defconfig        | 10 +--
 arch/mips/configs/cu1830-neo_defconfig        | 10 +--
 arch/mips/configs/e55_defconfig               |  4 +-
 arch/mips/configs/generic_defconfig           |  6 +-
 arch/mips/configs/gpr_defconfig               | 18 +---
 arch/mips/configs/loongson3_defconfig         | 13 +--
 arch/mips/configs/mpc30x_defconfig            |  7 +-
 arch/mips/configs/tb0219_defconfig            |  7 +-
 arch/mips/configs/tb0226_defconfig            |  7 +-
 arch/mips/configs/tb0287_defconfig            |  7 +-
 arch/mips/configs/workpad_defconfig           | 11 +--
 arch/mips/kernel/setup.c                      | 36 +-------
 arch/powerpc/Kconfig                          | 37 +-------
 arch/powerpc/configs/44x/fsp2_defconfig       | 33 ++++---
 arch/powerpc/configs/44x/iss476-smp_defconfig | 25 +++---
 arch/powerpc/configs/44x/warp_defconfig       | 17 ++--
 arch/powerpc/configs/holly_defconfig          | 13 +--
 arch/powerpc/configs/mvme5100_defconfig       | 23 ++---
 arch/powerpc/configs/skiroot_defconfig        | 12 ++-
 arch/powerpc/configs/storcenter_defconfig     | 18 ++--
 arch/powerpc/kernel/prom.c                    |  1 +
 arch/powerpc/kernel/prom_init.c               | 35 +++++---
 arch/x86/Kconfig                              | 44 +--------
 arch/x86/kernel/setup.c                       | 18 +---
 drivers/firmware/efi/libstub/x86-stub.c       |  2 +-
 drivers/of/fdt.c                              | 12 +++
 include/linux/cmdline.h                       | 89 +++++++++++++++++++
 init/Kconfig                                  | 68 ++++++++++++++
 37 files changed, 321 insertions(+), 385 deletions(-)
 create mode 100644 include/linux/cmdline.h

Comments

Randy Dunlap March 9, 2021, 1:17 a.m. UTC | #1 
On 3/8/21 3:53 PM, Daniel Walker wrote:
> This fixed some problem identified in my last release. I made updates
> based on comments from Christophe Leroy.
> 
> I added scripted updates to the defconfig file for mips and powerpc.
> This is required in order to maintain the status quo for those platforms
> which used the prior builtin command line system.
> 
> These were tested on all effected architectures.
> 
> Daniel Walker (7):
>   CMDLINE: add generic builtin command line
>   CMDLINE: drivers: of: ifdef out cmdline section
>   powerpc: convert config files to generic cmdline
>   CMDLINE: powerpc: convert to generic builtin command line
>   mips: convert config files to generic cmdline
>   CMDLINE: mips: convert to generic builtin command line
>   CMDLINE: x86: convert to generic builtin command line
> 


Hi Daniel,

These patches (1 - 7) should be sent as a Reply-to patch #0.

In .gitconfig, could you use
	thread = true

or use --thread on the command line?

HTH.
thanks.