Message ID | 1575896438-9562-7-git-send-email-zhouyanjie@wanyeetech.com (mailing list archive) |
---|---|
State | Superseded |
Delegated to: | Paul Burton |
Headers | show |
Series | [v7,1/6] MIPS: Ingenic: Initial X1000 support. | expand |
Hi Zhou, You modify here in patch [06/06] two files that were introduced in [04/06]. Just merge the two patches into one then, and make it last in the patchset. -Paul Le lun., déc. 9, 2019 at 21:00, 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> a écrit : > Add the CU1000 Neo devicetree and defconfig with PDMA, MMC, RTC, WDT > and NET enabled. > > Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> > --- > > Notes: > v7: > New patch, merge[06/12],[08/12],[10/12],[12/12] in v6. > > arch/mips/boot/dts/ingenic/cu1000-neo.dts | 47 > +++++++++++++++++++++++++++++++ > arch/mips/configs/cu1000-neo_defconfig | 17 +++++++++-- > 2 files changed, 62 insertions(+), 2 deletions(-) > > diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts > b/arch/mips/boot/dts/ingenic/cu1000-neo.dts > index 6f1a7e9..b0733da 100644 > --- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts > +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts > @@ -43,10 +43,57 @@ > status = "okay"; > }; > > +&mac { > + phy-mode = "rmii"; > + phy-handle = <&lan8720a>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pins_mac>; > + > + snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */ > + snps,reset-active-low; > + snps,reset-delays-us = <0 10000 30000>; > + > + status = "okay"; > +}; > + > +&mdio { > + status = "okay"; > + > + lan8720a: ethernet-phy@0 { > + compatible = "ethernet-phy-id0007.c0f0", > "ethernet-phy-ieee802.3-c22"; > + reg = <0>; > + }; > +}; > + > +&msc0 { > + bus-width = <8>; > + max-frequency = <50000000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pins_msc0>; > + > + non-removable; > + > + status = "okay"; > +}; > + > &pinctrl { > pins_uart2: uart2 { > function = "uart2"; > groups = "uart2-data-d"; > bias-disable; > }; > + > + pins_mac: mac { > + function = "mac"; > + groups = "mac"; > + bias-disable; > + }; > + > + pins_msc0: msc0 { > + function = "mmc0"; > + groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit"; > + bias-disable; > + }; > }; > diff --git a/arch/mips/configs/cu1000-neo_defconfig > b/arch/mips/configs/cu1000-neo_defconfig > index 4fafe92..9f988ed 100644 > --- a/arch/mips/configs/cu1000-neo_defconfig > +++ b/arch/mips/configs/cu1000-neo_defconfig > @@ -16,8 +16,6 @@ CONFIG_CGROUP_DEVICE=y > CONFIG_CGROUP_CPUACCT=y > CONFIG_NAMESPACES=y > CONFIG_USER_NS=y > -CONFIG_BLK_DEV_INITRD=y > -CONFIG_INITRAMFS_SOURCE="arch/mips/boot/ramdisk.cpio.gz" > CONFIG_CC_OPTIMIZE_FOR_SIZE=y > CONFIG_SYSCTL_SYSCALL=y > CONFIG_KALLSYMS_ALL=y > @@ -35,11 +33,17 @@ CONFIG_HZ_100=y > # CONFIG_COMPACTION is not set > CONFIG_CMA=y > CONFIG_CMA_AREAS=7 > +CONFIG_NET=y > +CONFIG_UNIX=y > +CONFIG_INET=y > CONFIG_UEVENT_HELPER=y > CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" > CONFIG_DEVTMPFS=y > # CONFIG_FW_LOADER is not set > # CONFIG_ALLOW_DEV_COREDUMP is not set > +CONFIG_NETDEVICES=y > +CONFIG_STMMAC_ETH=y > +CONFIG_SMSC_PHY=y > # CONFIG_INPUT_MOUSEDEV is not set > # CONFIG_INPUT_KEYBOARD is not set > # CONFIG_INPUT_MOUSE is not set > @@ -55,17 +59,26 @@ CONFIG_SERIAL_8250_INGENIC=y > CONFIG_SERIAL_OF_PLATFORM=y > # CONFIG_HW_RANDOM is not set > CONFIG_GPIO_SYSFS=y > +CONFIG_WATCHDOG=y > +CONFIG_JZ4740_WDT=y > # CONFIG_HWMON is not set > # CONFIG_LCD_CLASS_DEVICE is not set > # CONFIG_BACKLIGHT_CLASS_DEVICE is not set > # CONFIG_VGA_CONSOLE is not set > # CONFIG_HID is not set > # CONFIG_USB_SUPPORT is not set > +CONFIG_MMC=y > +CONFIG_MMC_JZ4740=y > +CONFIG_RTC_CLASS=y > +CONFIG_RTC_DRV_JZ4740=y > +CONFIG_DMADEVICES=y > +CONFIG_DMA_JZ4780=y > # CONFIG_IOMMU_SUPPORT is not set > CONFIG_NVMEM=y > CONFIG_NVMEM_SYSFS=y > CONFIG_EXT4_FS=y > # CONFIG_DNOTIFY is not set > +CONFIG_AUTOFS_FS=y > CONFIG_PROC_KCORE=y > # CONFIG_PROC_PAGE_MONITOR is not set > CONFIG_TMPFS=y > -- > 2.7.4 >
Hi Paul, On 2019年12月09日 23:07, Paul Cercueil wrote: > Hi Zhou, > > You modify here in patch [06/06] two files that were introduced in > [04/06]. Just merge the two patches into one then, and make it last in > the patchset. > Sure, I will merge the two patches in v8. Thanks and best regards! > -Paul > > > Le lun., déc. 9, 2019 at 21:00, 周琰杰 (Zhou Yanjie) > <zhouyanjie@wanyeetech.com> a écrit : >> Add the CU1000 Neo devicetree and defconfig with PDMA, MMC, RTC, WDT >> and NET enabled. >> >> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> >> --- >> >> Notes: >> v7: >> New patch, merge[06/12],[08/12],[10/12],[12/12] in v6. >> >> arch/mips/boot/dts/ingenic/cu1000-neo.dts | 47 >> +++++++++++++++++++++++++++++++ >> arch/mips/configs/cu1000-neo_defconfig | 17 +++++++++-- >> 2 files changed, 62 insertions(+), 2 deletions(-) >> >> diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts >> b/arch/mips/boot/dts/ingenic/cu1000-neo.dts >> index 6f1a7e9..b0733da 100644 >> --- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts >> +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts >> @@ -43,10 +43,57 @@ >> status = "okay"; >> }; >> >> +&mac { >> + phy-mode = "rmii"; >> + phy-handle = <&lan8720a>; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pins_mac>; >> + >> + snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */ >> + snps,reset-active-low; >> + snps,reset-delays-us = <0 10000 30000>; >> + >> + status = "okay"; >> +}; >> + >> +&mdio { >> + status = "okay"; >> + >> + lan8720a: ethernet-phy@0 { >> + compatible = "ethernet-phy-id0007.c0f0", >> "ethernet-phy-ieee802.3-c22"; >> + reg = <0>; >> + }; >> +}; >> + >> +&msc0 { >> + bus-width = <8>; >> + max-frequency = <50000000>; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pins_msc0>; >> + >> + non-removable; >> + >> + status = "okay"; >> +}; >> + >> &pinctrl { >> pins_uart2: uart2 { >> function = "uart2"; >> groups = "uart2-data-d"; >> bias-disable; >> }; >> + >> + pins_mac: mac { >> + function = "mac"; >> + groups = "mac"; >> + bias-disable; >> + }; >> + >> + pins_msc0: msc0 { >> + function = "mmc0"; >> + groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit"; >> + bias-disable; >> + }; >> }; >> diff --git a/arch/mips/configs/cu1000-neo_defconfig >> b/arch/mips/configs/cu1000-neo_defconfig >> index 4fafe92..9f988ed 100644 >> --- a/arch/mips/configs/cu1000-neo_defconfig >> +++ b/arch/mips/configs/cu1000-neo_defconfig >> @@ -16,8 +16,6 @@ CONFIG_CGROUP_DEVICE=y >> CONFIG_CGROUP_CPUACCT=y >> CONFIG_NAMESPACES=y >> CONFIG_USER_NS=y >> -CONFIG_BLK_DEV_INITRD=y >> -CONFIG_INITRAMFS_SOURCE="arch/mips/boot/ramdisk.cpio.gz" >> CONFIG_CC_OPTIMIZE_FOR_SIZE=y >> CONFIG_SYSCTL_SYSCALL=y >> CONFIG_KALLSYMS_ALL=y >> @@ -35,11 +33,17 @@ CONFIG_HZ_100=y >> # CONFIG_COMPACTION is not set >> CONFIG_CMA=y >> CONFIG_CMA_AREAS=7 >> +CONFIG_NET=y >> +CONFIG_UNIX=y >> +CONFIG_INET=y >> CONFIG_UEVENT_HELPER=y >> CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" >> CONFIG_DEVTMPFS=y >> # CONFIG_FW_LOADER is not set >> # CONFIG_ALLOW_DEV_COREDUMP is not set >> +CONFIG_NETDEVICES=y >> +CONFIG_STMMAC_ETH=y >> +CONFIG_SMSC_PHY=y >> # CONFIG_INPUT_MOUSEDEV is not set >> # CONFIG_INPUT_KEYBOARD is not set >> # CONFIG_INPUT_MOUSE is not set >> @@ -55,17 +59,26 @@ CONFIG_SERIAL_8250_INGENIC=y >> CONFIG_SERIAL_OF_PLATFORM=y >> # CONFIG_HW_RANDOM is not set >> CONFIG_GPIO_SYSFS=y >> +CONFIG_WATCHDOG=y >> +CONFIG_JZ4740_WDT=y >> # CONFIG_HWMON is not set >> # CONFIG_LCD_CLASS_DEVICE is not set >> # CONFIG_BACKLIGHT_CLASS_DEVICE is not set >> # CONFIG_VGA_CONSOLE is not set >> # CONFIG_HID is not set >> # CONFIG_USB_SUPPORT is not set >> +CONFIG_MMC=y >> +CONFIG_MMC_JZ4740=y >> +CONFIG_RTC_CLASS=y >> +CONFIG_RTC_DRV_JZ4740=y >> +CONFIG_DMADEVICES=y >> +CONFIG_DMA_JZ4780=y >> # CONFIG_IOMMU_SUPPORT is not set >> CONFIG_NVMEM=y >> CONFIG_NVMEM_SYSFS=y >> CONFIG_EXT4_FS=y >> # CONFIG_DNOTIFY is not set >> +CONFIG_AUTOFS_FS=y >> CONFIG_PROC_KCORE=y >> # CONFIG_PROC_PAGE_MONITOR is not set >> CONFIG_TMPFS=y >> -- >> 2.7.4 >> >
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts index 6f1a7e9..b0733da 100644 --- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts @@ -43,10 +43,57 @@ status = "okay"; }; +&mac { + phy-mode = "rmii"; + phy-handle = <&lan8720a>; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_mac>; + + snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */ + snps,reset-active-low; + snps,reset-delays-us = <0 10000 30000>; + + status = "okay"; +}; + +&mdio { + status = "okay"; + + lan8720a: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; + +&msc0 { + bus-width = <8>; + max-frequency = <50000000>; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_msc0>; + + non-removable; + + status = "okay"; +}; + &pinctrl { pins_uart2: uart2 { function = "uart2"; groups = "uart2-data-d"; bias-disable; }; + + pins_mac: mac { + function = "mac"; + groups = "mac"; + bias-disable; + }; + + pins_msc0: msc0 { + function = "mmc0"; + groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit"; + bias-disable; + }; }; diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig index 4fafe92..9f988ed 100644 --- a/arch/mips/configs/cu1000-neo_defconfig +++ b/arch/mips/configs/cu1000-neo_defconfig @@ -16,8 +16,6 @@ CONFIG_CGROUP_DEVICE=y CONFIG_CGROUP_CPUACCT=y CONFIG_NAMESPACES=y CONFIG_USER_NS=y -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="arch/mips/boot/ramdisk.cpio.gz" CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS_ALL=y @@ -35,11 +33,17 @@ CONFIG_HZ_100=y # CONFIG_COMPACTION is not set CONFIG_CMA=y CONFIG_CMA_AREAS=7 +CONFIG_NET=y +CONFIG_UNIX=y +CONFIG_INET=y CONFIG_UEVENT_HELPER=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_DEVTMPFS=y # CONFIG_FW_LOADER is not set # CONFIG_ALLOW_DEV_COREDUMP is not set +CONFIG_NETDEVICES=y +CONFIG_STMMAC_ETH=y +CONFIG_SMSC_PHY=y # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set @@ -55,17 +59,26 @@ CONFIG_SERIAL_8250_INGENIC=y CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_HW_RANDOM is not set CONFIG_GPIO_SYSFS=y +CONFIG_WATCHDOG=y +CONFIG_JZ4740_WDT=y # CONFIG_HWMON is not set # CONFIG_LCD_CLASS_DEVICE is not set # CONFIG_BACKLIGHT_CLASS_DEVICE is not set # CONFIG_VGA_CONSOLE is not set # CONFIG_HID is not set # CONFIG_USB_SUPPORT is not set +CONFIG_MMC=y +CONFIG_MMC_JZ4740=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_JZ4740=y +CONFIG_DMADEVICES=y +CONFIG_DMA_JZ4780=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_NVMEM=y CONFIG_NVMEM_SYSFS=y CONFIG_EXT4_FS=y # CONFIG_DNOTIFY is not set +CONFIG_AUTOFS_FS=y CONFIG_PROC_KCORE=y # CONFIG_PROC_PAGE_MONITOR is not set CONFIG_TMPFS=y
Add the CU1000 Neo devicetree and defconfig with PDMA, MMC, RTC, WDT and NET enabled. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> --- Notes: v7: New patch, merge[06/12],[08/12],[10/12],[12/12] in v6. arch/mips/boot/dts/ingenic/cu1000-neo.dts | 47 +++++++++++++++++++++++++++++++ arch/mips/configs/cu1000-neo_defconfig | 17 +++++++++-- 2 files changed, 62 insertions(+), 2 deletions(-)