@@ -2,7 +2,7 @@
# Makefile for lemote loongson2f family machines
#
-obj-y += clock.o machtype.o irq.o reset.o dma.o ec_kb3310b.o
+obj-y += clock.o machtype.o irq.o reset.o dma.o
#
# Suspend Support
deleted file mode 100644
@@ -1,129 +0,0 @@
-/*
- * Basic KB3310B Embedded Controller support for the YeeLoong 2F netbook
- *
- * Copyright (C) 2008 Lemote Inc.
- * Author: liujl <liujl@lemote.com>, 2008-04-20
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/io.h>
-#include <linux/export.h>
-#include <linux/spinlock.h>
-#include <linux/delay.h>
-
-#include "ec_kb3310b.h"
-
-static DEFINE_SPINLOCK(index_access_lock);
-static DEFINE_SPINLOCK(port_access_lock);
-
-unsigned char ec_read(unsigned short addr)
-{
- unsigned char value;
- unsigned long flags;
-
- spin_lock_irqsave(&index_access_lock, flags);
- outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
- outb((addr & 0x00ff), EC_IO_PORT_LOW);
- value = inb(EC_IO_PORT_DATA);
- spin_unlock_irqrestore(&index_access_lock, flags);
-
- return value;
-}
-EXPORT_SYMBOL_GPL(ec_read);
-
-void ec_write(unsigned short addr, unsigned char val)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&index_access_lock, flags);
- outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
- outb((addr & 0x00ff), EC_IO_PORT_LOW);
- outb(val, EC_IO_PORT_DATA);
- /* flush the write action */
- inb(EC_IO_PORT_DATA);
- spin_unlock_irqrestore(&index_access_lock, flags);
-}
-EXPORT_SYMBOL_GPL(ec_write);
-
-/*
- * This function is used for EC command writes and corresponding status queries.
- */
-int ec_query_seq(unsigned char cmd)
-{
- int timeout;
- unsigned char status;
- unsigned long flags;
- int ret = 0;
-
- spin_lock_irqsave(&port_access_lock, flags);
-
- /* make chip goto reset mode */
- udelay(EC_REG_DELAY);
- outb(cmd, EC_CMD_PORT);
- udelay(EC_REG_DELAY);
-
- /* check if the command is received by ec */
- timeout = EC_CMD_TIMEOUT;
- status = inb(EC_STS_PORT);
- while (timeout-- && (status & (1 << 1))) {
- status = inb(EC_STS_PORT);
- udelay(EC_REG_DELAY);
- }
-
- spin_unlock_irqrestore(&port_access_lock, flags);
-
- if (timeout <= 0) {
- printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
- ret = -EINVAL;
- } else
- printk(KERN_INFO
- "(%x/%d)ec issued command %d status : 0x%x\n",
- timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
-
- return ret;
-}
-EXPORT_SYMBOL_GPL(ec_query_seq);
-
-/*
- * Send query command to EC to get the proper event number
- */
-int ec_query_event_num(void)
-{
- return ec_query_seq(CMD_GET_EVENT_NUM);
-}
-EXPORT_SYMBOL(ec_query_event_num);
-
-/*
- * Get event number from EC
- *
- * NOTE: This routine must follow the query_event_num function in the
- * interrupt.
- */
-int ec_get_event_num(void)
-{
- int timeout = 100;
- unsigned char value;
- unsigned char status;
-
- udelay(EC_REG_DELAY);
- status = inb(EC_STS_PORT);
- udelay(EC_REG_DELAY);
- while (timeout-- && !(status & (1 << 0))) {
- status = inb(EC_STS_PORT);
- udelay(EC_REG_DELAY);
- }
- if (timeout <= 0) {
- pr_info("%s: get event number timeout.\n", __func__);
-
- return -EINVAL;
- }
- value = inb(EC_DAT_PORT);
- udelay(EC_REG_DELAY);
-
- return value;
-}
-EXPORT_SYMBOL(ec_get_event_num);
deleted file mode 100644
@@ -1,188 +0,0 @@
-/*
- * KB3310B Embedded Controller
- *
- * Copyright (C) 2008 Lemote Inc.
- * Author: liujl <liujl@lemote.com>, 2008-03-14
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef _EC_KB3310B_H
-#define _EC_KB3310B_H
-
-extern unsigned char ec_read(unsigned short addr);
-extern void ec_write(unsigned short addr, unsigned char val);
-extern int ec_query_seq(unsigned char cmd);
-extern int ec_query_event_num(void);
-extern int ec_get_event_num(void);
-
-typedef int (*sci_handler) (int status);
-extern sci_handler yeeloong_report_lid_status;
-
-#define SCI_IRQ_NUM 0x0A
-
-/*
- * The following registers are determined by the EC index configuration.
- * 1, fill the PORT_HIGH as EC register high part.
- * 2, fill the PORT_LOW as EC register low part.
- * 3, fill the PORT_DATA as EC register write data or get the data from it.
- */
-#define EC_IO_PORT_HIGH 0x0381
-#define EC_IO_PORT_LOW 0x0382
-#define EC_IO_PORT_DATA 0x0383
-
-/*
- * EC delay time is 500us for register and status access
- */
-#define EC_REG_DELAY 500 /* unit : us */
-#define EC_CMD_TIMEOUT 0x1000
-
-/*
- * EC access port for SCI communication
- */
-#define EC_CMD_PORT 0x66
-#define EC_STS_PORT 0x66
-#define EC_DAT_PORT 0x62
-#define CMD_INIT_IDLE_MODE 0xdd
-#define CMD_EXIT_IDLE_MODE 0xdf
-#define CMD_INIT_RESET_MODE 0xd8
-#define CMD_REBOOT_SYSTEM 0x8c
-#define CMD_GET_EVENT_NUM 0x84
-#define CMD_PROGRAM_PIECE 0xda
-
-/* temperature & fan registers */
-#define REG_TEMPERATURE_VALUE 0xF458
-#define REG_FAN_AUTO_MAN_SWITCH 0xF459
-#define BIT_FAN_AUTO 0
-#define BIT_FAN_MANUAL 1
-#define REG_FAN_CONTROL 0xF4D2
-#define BIT_FAN_CONTROL_ON (1 << 0)
-#define BIT_FAN_CONTROL_OFF (0 << 0)
-#define REG_FAN_STATUS 0xF4DA
-#define BIT_FAN_STATUS_ON (1 << 0)
-#define BIT_FAN_STATUS_OFF (0 << 0)
-#define REG_FAN_SPEED_HIGH 0xFE22
-#define REG_FAN_SPEED_LOW 0xFE23
-#define REG_FAN_SPEED_LEVEL 0xF4CC
-/* fan speed divider */
-#define FAN_SPEED_DIVIDER 480000 /* (60*1000*1000/62.5/2)*/
-
-/* battery registers */
-#define REG_BAT_DESIGN_CAP_HIGH 0xF77D
-#define REG_BAT_DESIGN_CAP_LOW 0xF77E
-#define REG_BAT_FULLCHG_CAP_HIGH 0xF780
-#define REG_BAT_FULLCHG_CAP_LOW 0xF781
-#define REG_BAT_DESIGN_VOL_HIGH 0xF782
-#define REG_BAT_DESIGN_VOL_LOW 0xF783
-#define REG_BAT_CURRENT_HIGH 0xF784
-#define REG_BAT_CURRENT_LOW 0xF785
-#define REG_BAT_VOLTAGE_HIGH 0xF786
-#define REG_BAT_VOLTAGE_LOW 0xF787
-#define REG_BAT_TEMPERATURE_HIGH 0xF788
-#define REG_BAT_TEMPERATURE_LOW 0xF789
-#define REG_BAT_RELATIVE_CAP_HIGH 0xF492
-#define REG_BAT_RELATIVE_CAP_LOW 0xF493
-#define REG_BAT_VENDOR 0xF4C4
-#define FLAG_BAT_VENDOR_SANYO 0x01
-#define FLAG_BAT_VENDOR_SIMPLO 0x02
-#define REG_BAT_CELL_COUNT 0xF4C6
-#define FLAG_BAT_CELL_3S1P 0x03
-#define FLAG_BAT_CELL_3S2P 0x06
-#define REG_BAT_CHARGE 0xF4A2
-#define FLAG_BAT_CHARGE_DISCHARGE 0x01
-#define FLAG_BAT_CHARGE_CHARGE 0x02
-#define FLAG_BAT_CHARGE_ACPOWER 0x00
-#define REG_BAT_STATUS 0xF4B0
-#define BIT_BAT_STATUS_LOW (1 << 5)
-#define BIT_BAT_STATUS_DESTROY (1 << 2)
-#define BIT_BAT_STATUS_FULL (1 << 1)
-#define BIT_BAT_STATUS_IN (1 << 0)
-#define REG_BAT_CHARGE_STATUS 0xF4B1
-#define BIT_BAT_CHARGE_STATUS_OVERTEMP (1 << 2)
-#define BIT_BAT_CHARGE_STATUS_PRECHG (1 << 1)
-#define REG_BAT_STATE 0xF482
-#define BIT_BAT_STATE_CHARGING (1 << 1)
-#define BIT_BAT_STATE_DISCHARGING (1 << 0)
-#define REG_BAT_POWER 0xF440
-#define BIT_BAT_POWER_S3 (1 << 2)
-#define BIT_BAT_POWER_ON (1 << 1)
-#define BIT_BAT_POWER_ACIN (1 << 0)
-
-/* other registers */
-/* Audio: rd/wr */
-#define REG_AUDIO_VOLUME 0xF46C
-#define REG_AUDIO_MUTE 0xF4E7
-#define REG_AUDIO_BEEP 0xF4D0
-/* USB port power or not: rd/wr */
-#define REG_USB0_FLAG 0xF461
-#define REG_USB1_FLAG 0xF462
-#define REG_USB2_FLAG 0xF463
-#define BIT_USB_FLAG_ON 1
-#define BIT_USB_FLAG_OFF 0
-/* LID */
-#define REG_LID_DETECT 0xF4BD
-#define BIT_LID_DETECT_ON 1
-#define BIT_LID_DETECT_OFF 0
-/* CRT */
-#define REG_CRT_DETECT 0xF4AD
-#define BIT_CRT_DETECT_PLUG 1
-#define BIT_CRT_DETECT_UNPLUG 0
-/* LCD backlight brightness adjust: 9 levels */
-#define REG_DISPLAY_BRIGHTNESS 0xF4F5
-/* Black screen Status */
-#define BIT_DISPLAY_LCD_ON 1
-#define BIT_DISPLAY_LCD_OFF 0
-/* LCD backlight control: off/restore */
-#define REG_BACKLIGHT_CTRL 0xF7BD
-#define BIT_BACKLIGHT_ON 1
-#define BIT_BACKLIGHT_OFF 0
-/* Reset the machine auto-clear: rd/wr */
-#define REG_RESET 0xF4EC
-#define BIT_RESET_ON 1
-/* Light the led: rd/wr */
-#define REG_LED 0xF4C8
-#define BIT_LED_RED_POWER (1 << 0)
-#define BIT_LED_ORANGE_POWER (1 << 1)
-#define BIT_LED_GREEN_CHARGE (1 << 2)
-#define BIT_LED_RED_CHARGE (1 << 3)
-#define BIT_LED_NUMLOCK (1 << 4)
-/* Test led mode, all led on/off */
-#define REG_LED_TEST 0xF4C2
-#define BIT_LED_TEST_IN 1
-#define BIT_LED_TEST_OUT 0
-/* Camera on/off */
-#define REG_CAMERA_STATUS 0xF46A
-#define BIT_CAMERA_STATUS_ON 1
-#define BIT_CAMERA_STATUS_OFF 0
-#define REG_CAMERA_CONTROL 0xF7B7
-#define BIT_CAMERA_CONTROL_OFF 0
-#define BIT_CAMERA_CONTROL_ON 1
-/* Wlan Status */
-#define REG_WLAN 0xF4FA
-#define BIT_WLAN_ON 1
-#define BIT_WLAN_OFF 0
-#define REG_DISPLAY_LCD 0xF79F
-
-/* SCI Event Number from EC */
-enum {
- EVENT_LID = 0x23, /* LID open/close */
- EVENT_DISPLAY_TOGGLE, /* Fn+F3 for display switch */
- EVENT_SLEEP, /* Fn+F1 for entering sleep mode */
- EVENT_OVERTEMP, /* Over-temperature happened */
- EVENT_CRT_DETECT, /* CRT is connected */
- EVENT_CAMERA, /* Camera on/off */
- EVENT_USB_OC2, /* USB2 Over Current occurred */
- EVENT_USB_OC0, /* USB0 Over Current occurred */
- EVENT_BLACK_SCREEN, /* Turn on/off backlight */
- EVENT_AUDIO_MUTE, /* Mute on/off */
- EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
- EVENT_AC_BAT, /* AC & Battery relative issue */
- EVENT_AUDIO_VOLUME, /* Volume adjust */
- EVENT_WLAN, /* Wlan on/off */
- EVENT_END
-};
-
-#endif /* !_EC_KB3310B_H */
@@ -23,7 +23,7 @@
#include <loongson.h>
#include <cs5536/cs5536_mfgpt.h>
-#include "ec_kb3310b.h"
+#include <linux/mfd/yeeloong_kb3310b.h>
#define I8042_KBD_IRQ 1
#define I8042_CTR_KBDINT 0x01
@@ -70,7 +70,7 @@ void setup_wakeup_events(void)
/* Wakeup CPU via SCI lid open event */
outb(irq_mask & ~(1 << PIC_CASCADE_IR), PIC_MASTER_IMR);
inb(PIC_MASTER_IMR);
- outb(0xff & ~(1 << (SCI_IRQ_NUM - 8)), PIC_SLAVE_IMR);
+ outb(0xff & ~(1 << (KB3310B_SCI_IRQ_NUM - 8)), PIC_SLAVE_IMR);
inb(PIC_SLAVE_IMR);
break;
@@ -88,7 +88,7 @@ EXPORT_SYMBOL(yeeloong_report_lid_status);
static void yeeloong_lid_update_task(struct work_struct *work)
{
if (yeeloong_report_lid_status)
- yeeloong_report_lid_status(BIT_LID_DETECT_ON);
+ yeeloong_report_lid_status(KB3310B_BIT_LID_DETECT_ON);
}
int wakeup_loongson(void)
@@ -104,21 +104,21 @@ int wakeup_loongson(void)
if (irq == I8042_KBD_IRQ)
return 1;
- else if (irq == SCI_IRQ_NUM) {
+ else if (irq == KB3310B_SCI_IRQ_NUM) {
int ret, sci_event;
/* query the event number */
- ret = ec_query_seq(CMD_GET_EVENT_NUM);
+ ret = kb3310b_query_seq(KB3310B_CMD_GET_EVENT_NUM);
if (ret < 0)
return 0;
- sci_event = ec_get_event_num();
+ sci_event = kb3310b_get_event_num();
if (sci_event < 0)
return 0;
- if (sci_event == EVENT_LID) {
+ if (sci_event == KB3310B_EVENT_LID) {
int lid_status;
/* check the LID status */
- lid_status = ec_read(REG_LID_DETECT);
+ lid_status = kb3310b_read(KB3310B_REG_LID_DETECT);
/* wakeup cpu when people open the LID */
- if (lid_status == BIT_LID_DETECT_ON) {
+ if (lid_status == KB3310B_BIT_LID_DETECT_ON) {
/* If we call it directly here, the WARNING
* will be sent out by getnstimeofday
* via "WARN_ON(timekeeping_suspended);"
@@ -20,7 +20,7 @@
#include <loongson.h>
#include <cs5536/cs5536.h>
-#include "ec_kb3310b.h"
+#include <linux/mfd/yeeloong_kb3310b.h>
static void reset_cpu(void)
{
@@ -81,7 +81,7 @@ static void ml2f_reboot(void)
reset_cpu();
/* sending an reset signal to EC(embedded controller) */
- ec_write(REG_RESET, BIT_RESET_ON);
+ kb3310b_write(KB3310B_REG_RESET, KB3310B_BIT_RESET_ON);
}
#define yl2f89_reboot ml2f_reboot
We have already converted the supporting code for ENE KB3310B embedded controller as a separate MFD driver, and select it as a dependency of LEMOTE_MACH2F. This commit removes the original implementation of ec_kb3310b.c, and converts all EC operations to use the utility function provided by the yeeloong_kb3310b MFD driver instead. Signed-off-by: Yifeng Li <tomli@tomli.me> --- arch/mips/loongson64/lemote-2f/Makefile | 2 +- arch/mips/loongson64/lemote-2f/ec_kb3310b.c | 129 -------------- arch/mips/loongson64/lemote-2f/ec_kb3310b.h | 188 -------------------- arch/mips/loongson64/lemote-2f/pm.c | 18 +- arch/mips/loongson64/lemote-2f/reset.c | 4 +- 5 files changed, 12 insertions(+), 329 deletions(-) delete mode 100644 arch/mips/loongson64/lemote-2f/ec_kb3310b.c delete mode 100644 arch/mips/loongson64/lemote-2f/ec_kb3310b.h