diff mbox series

[2/8,v2] MIPS: ralink: mt7628a.dtsi: Add pinmux DT node

Message ID 20190527091323.4582-2-sr@denx.de (mailing list archive)
State Accepted
Headers show
Series [1/8,v2] MIPS: ralink: mt7628a.dtsi: Add SPDX GPL-2.0 license identifier | expand

Commit Message

Stefan Roese May 27, 2019, 9:13 a.m. UTC 
This patch adds the pinmux DT node using the generic "pinctrl-single"
pinmux driver. For this the system-controller register area needs to be
changed to not overlap with the pinmux registers.

This patch is based on work done by John Crispin.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
---
v2:
- Use Harvey's new email address (not at imgtec)
- Use correct linux-mips list address

 arch/mips/boot/dts/ralink/mt7628a.dtsi | 95 +++++++++++++++++++++++++-
 1 file changed, 94 insertions(+), 1 deletion(-)

Comments

Paul Burton June 24, 2019, 9:16 p.m. UTC | #1 
Hello,

Stefan Roese wrote:
> This patch adds the pinmux DT node using the generic "pinctrl-single"
> pinmux driver. For this the system-controller register area needs to be
> changed to not overlap with the pinmux registers.
> 
> This patch is based on work done by John Crispin.
> 
> Signed-off-by: Stefan Roese <sr@denx.de>
> Cc: Paul Burton <paul.burton@mips.com>
> Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
> Cc: John Crispin <john@phrozen.org>

Applied to mips-next.

Thanks,
    Paul

[ This message was auto-generated; if you believe anything is incorrect
  then please email paul.burton@mips.com to report it. ]
diff mbox series

Patch

diff --git a/arch/mips/boot/dts/ralink/mt7628a.dtsi b/arch/mips/boot/dts/ralink/mt7628a.dtsi
index 3e88c8d496e4..d87f53bd6d72 100644
--- a/arch/mips/boot/dts/ralink/mt7628a.dtsi
+++ b/arch/mips/boot/dts/ralink/mt7628a.dtsi
@@ -38,7 +38,100 @@ 
 
 		sysc: system-controller@0 {
 			compatible = "ralink,mt7620a-sysc", "syscon";
-			reg = <0x0 0x100>;
+			reg = <0x0 0x60>;
+		};
+
+		pinmux: pinmux@60 {
+			compatible = "pinctrl-single";
+			reg = <0x60 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pinctrl-cells = <2>;
+			pinctrl-single,bit-per-mux;
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <0x1>;
+
+			pinmux_gpio_gpio: pinmux_gpio_gpio {
+				pinctrl-single,bits = <0x0 0x0 0x3>;
+			};
+
+			pinmux_spi_cs1_cs: pinmux_spi_cs1_cs {
+				pinctrl-single,bits = <0x0 0x0 0x30>;
+			};
+
+			pinmux_i2s_gpio: pinmux_i2s_gpio {
+				pinctrl-single,bits = <0x0 0x40 0xc0>;
+			};
+
+			pinmux_uart0_uart: pinmux_uart0_uart0 {
+				pinctrl-single,bits = <0x0 0x0 0x300>;
+			};
+
+			pinmux_sdmode_sdxc: pinmux_sdmode_sdxc {
+				pinctrl-single,bits = <0x0 0x0 0xc00>;
+			};
+
+			pinmux_sdmode_gpio: pinmux_sdmode_gpio {
+				pinctrl-single,bits = <0x0 0x400 0xc00>;
+			};
+
+			pinmux_spi_spi: pinmux_spi_spi {
+				pinctrl-single,bits = <0x0 0x0 0x1000>;
+			};
+
+			pinmux_refclk_gpio: pinmux_refclk_gpio {
+				pinctrl-single,bits = <0x0 0x40000 0x40000>;
+			};
+
+			pinmux_i2c_i2c: pinmux_i2c_i2c {
+				pinctrl-single,bits = <0x0 0x0 0x300000>;
+			};
+
+			pinmux_uart1_uart: pinmux_uart1_uart1 {
+				pinctrl-single,bits = <0x0 0x0 0x3000000>;
+			};
+
+			pinmux_uart2_uart: pinmux_uart2_uart {
+				pinctrl-single,bits = <0x0 0x0 0xc000000>;
+			};
+
+			pinmux_pwm0_pwm: pinmux_pwm0_pwm {
+				pinctrl-single,bits = <0x0 0x0 0x30000000>;
+			};
+
+			pinmux_pwm0_gpio: pinmux_pwm0_gpio {
+				pinctrl-single,bits = <0x0 0x10000000
+						       0x30000000>;
+			};
+
+			pinmux_pwm1_pwm: pinmux_pwm1_pwm {
+				pinctrl-single,bits = <0x0 0x0 0xc0000000>;
+			};
+
+			pinmux_pwm1_gpio: pinmux_pwm1_gpio {
+				pinctrl-single,bits = <0x0 0x40000000
+						       0xc0000000>;
+			};
+
+			pinmux_p0led_an_gpio: pinmux_p0led_an_gpio {
+				pinctrl-single,bits = <0x4 0x4 0xc>;
+			};
+
+			pinmux_p1led_an_gpio: pinmux_p1led_an_gpio {
+				pinctrl-single,bits = <0x4 0x10 0x30>;
+			};
+
+			pinmux_p2led_an_gpio: pinmux_p2led_an_gpio {
+				pinctrl-single,bits = <0x4 0x40 0xc0>;
+			};
+
+			pinmux_p3led_an_gpio: pinmux_p3led_an_gpio {
+				pinctrl-single,bits = <0x4 0x100 0x300>;
+			};
+
+			pinmux_p4led_an_gpio: pinmux_p4led_an_gpio {
+				pinctrl-single,bits = <0x4 0x400 0xc00>;
+			};
 		};
 
 		intc: interrupt-controller@200 {