@@ -17,6 +17,7 @@ platforms += jazz
platforms += jz4740
platforms += lantiq
platforms += lasat
+platforms += loongson2ef
platforms += loongson32
platforms += loongson64
platforms += mti-malta
@@ -445,18 +445,52 @@ config MACH_LOONGSON32
the Institute of Computing Technology (ICT), Chinese Academy of
Sciences (CAS).
+config MACH_LOONGSON2EF
+ bool "Loongson-2E/F family of machines"
+ select SYS_SUPPORTS_ZBOOT
+ help
+ This enables the support of Loongson-2E/F family of machines.
+
+ Loongson-2E/F is a family of single-core CPUs, They are 64-bit
+ general-purpose MIPS-III compatible CPUs. Loongson-2E/F are developed
+ by the Institute of Computing Technology (ICT), Chinese Academy of
+ Sciences (CAS) in the People's Republic of China.
+ The chief architect is Professor Weiwu Hu.
+
config MACH_LOONGSON64
- bool "Loongson-2/3 family of machines"
+ bool "Loongson GSx64 family of machines"
+ select ARCH_SPARSEMEM_ENABLE
+ select ARCH_MIGHT_HAVE_PC_PARPORT
+ select ARCH_MIGHT_HAVE_PC_SERIO
+ select GENERIC_ISA_DMA_SUPPORT_BROKEN
+ select BOOT_ELF32
+ select BOARD_SCACHE
+ select CSRC_R4K
+ select CEVT_R4K
+ select CPU_HAS_WB
+ select FORCE_PCI
+ select ISA
+ select I8259
+ select IRQ_MIPS_CPU
+ select NUMA
+ select NR_CPUS_DEFAULT_32
+ select SYS_HAS_CPU_LOONGSON64
+ select SYS_HAS_EARLY_PRINTK
+ select USE_GENERIC_EARLY_PRINTK_8250
+ select SYS_SUPPORTS_SMP
+ select SYS_SUPPORTS_HOTPLUG_CPU
+ select SYS_SUPPORTS_NUMA
+ select SYS_SUPPORTS_64BIT_KERNEL
+ select SYS_SUPPORTS_HIGHMEM
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select ZONE_DMA32
select SYS_SUPPORTS_ZBOOT
help
- This enables the support of Loongson-2/3 family of machines.
+ This enables the support of Loongson-3A/3B/2-series-soc processors
- Loongson-2 is a family of single-core CPUs and Loongson-3 is a
- family of multi-core CPUs. They are both 64-bit general-purpose
- MIPS-compatible CPUs. Loongson-2/3 are developed by the Institute
- of Computing Technology (ICT), Chinese Academy of Sciences (CAS)
- in the People's Republic of China. The chief architect is Professor
- Weiwu Hu.
+ GSx64 is a family of general-purpose MIPS64R2+ procossor featured
+ multi-core support. Their firmwares are passing parameters according
+ to uniformed "Loongson Firmware Kernel Interface Specification".
config MACH_PISTACHIO
bool "IMG Pistachio SoC based boards"
@@ -1033,6 +1067,7 @@ source "arch/mips/sibyte/Kconfig"
source "arch/mips/txx9/Kconfig"
source "arch/mips/vr41xx/Kconfig"
source "arch/mips/cavium-octeon/Kconfig"
+source "arch/mips/loongson2ef/Kconfig"
source "arch/mips/loongson32/Kconfig"
source "arch/mips/loongson64/Kconfig"
source "arch/mips/netlogic/Kconfig"
@@ -70,7 +70,6 @@ enum loongson_machine_type {
MACH_DEXXON_GDIUM2F10,
MACH_LEMOTE_NAS,
MACH_LEMOTE_LL2F,
- MACH_LOONGSON_GENERIC,
MACH_LOONGSON_END
};
new file mode 100644
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ * Copyright (C) 2009 Philippe Vachon <philippe@cowpig.ca>
+ * Copyright (C) 2009 Zhang Le <r0bertz@gentoo.org>
+ *
+ * reference: /proc/cpuinfo,
+ * arch/mips/kernel/cpu-probe.c(cpu_probe_legacy),
+ * arch/mips/kernel/proc.c(show_cpuinfo),
+ * loongson2f user manual.
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_LOONGSON2EF_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_32fpr 1
+#define cpu_has_3k_cache 0
+#define cpu_has_4k_cache 1
+#define cpu_has_4kex 1
+#define cpu_has_64bits 1
+#define cpu_has_cache_cdex_p 0
+#define cpu_has_cache_cdex_s 0
+#define cpu_has_counter 1
+#define cpu_has_dc_aliases (PAGE_SIZE < 0x4000)
+#define cpu_has_divec 0
+#define cpu_has_ejtag 0
+#define cpu_has_inclusive_pcaches 1
+#define cpu_has_llsc 1
+#define cpu_has_mcheck 0
+#define cpu_has_mdmx 0
+#define cpu_has_mips16 0
+#define cpu_has_mips16e2 0
+#define cpu_has_mips3d 0
+#define cpu_has_mipsmt 0
+#define cpu_has_smartmips 0
+#define cpu_has_tlb 1
+#define cpu_has_tx39_cache 0
+#define cpu_has_vce 0
+#define cpu_has_veic 0
+#define cpu_has_vint 0
+#define cpu_has_vtag_icache 0
+#define cpu_has_watch 1
+#define cpu_has_local_ebase 0
+
+#endif /* __ASM_MACH_LOONGSON2EF_CPU_FEATURE_OVERRIDES_H */
similarity index 100%
rename from arch/mips/include/asm/mach-loongson64/cs5536/cs5536.h
rename to arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536.h
similarity index 100%
rename from arch/mips/include/asm/mach-loongson64/cs5536/cs5536_mfgpt.h
rename to arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_mfgpt.h
similarity index 100%
rename from arch/mips/include/asm/mach-loongson64/cs5536/cs5536_pci.h
rename to arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_pci.h
similarity index 100%
rename from arch/mips/include/asm/mach-loongson64/cs5536/cs5536_vsm.h
rename to arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_vsm.h
similarity index 91%
rename from arch/mips/include/asm/mach-loongson64/loongson.h
rename to arch/mips/include/asm/mach-loongson2ef/loongson2ef.h
@@ -4,13 +4,12 @@
* Author: Wu Zhangjin <wuzhangjin@gmail.com>
*/
-#ifndef __ASM_MACH_LOONGSON64_LOONGSON_H
-#define __ASM_MACH_LOONGSON64_LOONGSON_H
+#ifndef __ASM_MACH_LOONGSON2EF_LOONGSON2EF_H
+#define __ASM_MACH_LOONGSON2EF_LOONGSON2EF_H
#include <linux/io.h>
#include <linux/init.h>
#include <linux/irq.h>
-#include <boot_param.h>
/* loongson internal northbridge initialization */
extern void bonito_irq_init(void);
@@ -22,7 +21,6 @@ extern void mach_prepare_shutdown(void);
/* environment arguments from bootloader */
extern u32 cpu_clock_freq;
extern u32 memsize, highmemsize;
-extern const struct plat_smp_ops loongson3_smp_ops;
/* loongson-specific command line, env and memory initialization */
extern void __init prom_init_memory(void);
@@ -58,11 +56,6 @@ extern int mach_i8259_irq(void);
#define LOONGSON_REG(x) \
(*(volatile u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
-#define LOONGSON3_REG8(base, x) \
- (*(volatile u8 *)((char *)TO_UNCAC(base) + (x)))
-
-#define LOONGSON3_REG32(base, x) \
- (*(volatile u32 *)((char *)TO_UNCAC(base) + (x)))
#define LOONGSON_IRQ_BASE 32
#define LOONGSON2_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6) /* cpu perf counter */
@@ -89,10 +82,6 @@ static inline void do_perfcnt_IRQ(void)
#define LOONGSON_REG_BASE 0x1fe00000
#define LOONGSON_REG_SIZE 0x00100000 /* 256Bytes + 256Bytes + ??? */
#define LOONGSON_REG_TOP (LOONGSON_REG_BASE+LOONGSON_REG_SIZE-1)
-/* Loongson-3 specific registers */
-#define LOONGSON3_REG_BASE 0x3ff00000
-#define LOONGSON3_REG_SIZE 0x00100000 /* 256Bytes + 256Bytes + ??? */
-#define LOONGSON3_REG_TOP (LOONGSON3_REG_BASE+LOONGSON3_REG_SIZE-1)
#define LOONGSON_LIO1_BASE 0x1ff00000
#define LOONGSON_LIO1_SIZE 0x00100000 /* 1M */
@@ -247,19 +236,9 @@ static inline void do_perfcnt_IRQ(void)
#define MAX_PACKAGES 4
/* Chip Config registor of each physical cpu package, PRid >= Loongson-2F */
-extern u64 loongson_chipcfg[MAX_PACKAGES];
-#define LOONGSON_CHIPCFG(id) (*(volatile u32 *)(loongson_chipcfg[id]))
-
-/* Chip Temperature registor of each physical cpu package, PRid >= Loongson-3A */
-extern u64 loongson_chiptemp[MAX_PACKAGES];
-#define LOONGSON_CHIPTEMP(id) (*(volatile u32 *)(loongson_chiptemp[id]))
-
-/* Freq Control register of each physical cpu package, PRid >= Loongson-3B */
-extern u64 loongson_freqctrl[MAX_PACKAGES];
-#define LOONGSON_FREQCTRL(id) (*(volatile u32 *)(loongson_freqctrl[id]))
+#define LOONGSON_CHIPCFG(id) (*(volatile u32 *)(0xffffffffbfc00180))
/* pcimap */
-
#define LOONGSON_PCIMAP_PCIMAP_LO0 0x0000003f
#define LOONGSON_PCIMAP_PCIMAP_LO0_SHIFT 0
#define LOONGSON_PCIMAP_PCIMAP_LO1 0x00000fc0
@@ -352,4 +331,4 @@ extern unsigned long _loongson_addrwincfg_base;
#endif /* ! CONFIG_CPU_SUPPORTS_ADDRWINCFG */
-#endif /* __ASM_MACH_LOONGSON64_LOONGSON_H */
+#endif /* __ASM_MACH_LOONGSON2EF_LOONGSON_H */
similarity index 80%
rename from arch/mips/include/asm/mach-loongson64/machine.h
rename to arch/mips/include/asm/mach-loongson2ef/machine.h
@@ -20,10 +20,4 @@
#endif
-#ifdef CONFIG_LOONGSON_MACH3X
-
-#define LOONGSON_MACHTYPE MACH_LOONGSON_GENERIC
-
-#endif /* CONFIG_LOONGSON_MACH3X */
-
#endif /* __ASM_MACH_LOONGSON64_MACHINE_H */
similarity index 80%
rename from arch/mips/include/asm/mach-loongson64/mc146818rtc.h
rename to arch/mips/include/asm/mach-loongson2ef/mc146818rtc.h
@@ -1,8 +1,5 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
* Copyright (C) 1998, 2001, 03, 07 by Ralf Baechle (ralf@linux-mips.org)
*
* RTC routines for PC style attached Dallas chip.
similarity index 86%
rename from arch/mips/include/asm/mach-loongson64/mem.h
rename to arch/mips/include/asm/mach-loongson2ef/mem.h
@@ -4,8 +4,8 @@
* Author: Wu Zhangjin <wuzhangjin@gmail.com>
*/
-#ifndef __ASM_MACH_LOONGSON64_MEM_H
-#define __ASM_MACH_LOONGSON64_MEM_H
+#ifndef __ASM_MACH_LOONGSON2EF_MEM_H
+#define __ASM_MACH_LOONGSON2EF_MEM_H
/*
* high memory space
@@ -34,4 +34,4 @@
#define LOONGSON_MMIO_MEM_END 0x80000000
#endif
-#endif /* __ASM_MACH_LOONGSON64_MEM_H */
+#endif /* __ASM_MACH_LOONGSON2EF_MEM_H */
new file mode 100644
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2008 Zhang Le <r0bertz@gentoo.org>
+ * Copyright (c) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_PCI_H_
+#define __ASM_MACH_LOONGSON2EF_PCI_H_
+
+extern struct pci_ops loongson_pci_ops;
+
+/* this is an offset from mips_io_port_base */
+#define LOONGSON_PCI_IO_START 0x00004000UL
+
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+
+/*
+ * we use address window2 to map cpu address space to pci space
+ * window2: cpu [1G, 2G] -> pci [1G, 2G]
+ * why not use window 0 & 1? because they are used by cpu when booting.
+ * window0: cpu [0, 256M] -> ddr [0, 256M]
+ * window1: cpu [256M, 512M] -> pci [256M, 512M]
+ */
+
+/* the smallest LOONGSON_CPU_MEM_SRC can be 512M */
+#define LOONGSON_CPU_MEM_SRC 0x40000000ul /* 1G */
+#define LOONGSON_PCI_MEM_DST LOONGSON_CPU_MEM_SRC
+
+#define LOONGSON_PCI_MEM_START LOONGSON_PCI_MEM_DST
+#define LOONGSON_PCI_MEM_END (0x80000000ul-1) /* 2G */
+
+#define MMAP_CPUTOPCI_SIZE (LOONGSON_PCI_MEM_END - \
+ LOONGSON_PCI_MEM_START + 1)
+
+#else /* loongson2f/32bit & loongson2e */
+
+/* this pci memory space is mapped by pcimap in pci.c */
+#define LOONGSON_PCI_MEM_START LOONGSON_PCILO1_BASE
+#define LOONGSON_PCI_MEM_END (LOONGSON_PCILO1_BASE + 0x04000000 * 2)
+
+#endif /* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
+
+#endif /* !__ASM_MACH_LOONGSON2EF_PCI_H_ */
new file mode 100644
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON2EF_SPACES_H_
+#define __ASM_MACH_LOONGSON2EF_SPACES_H_
+
+#if defined(CONFIG_64BIT)
+#define CAC_BASE _AC(0x9800000000000000, UL)
+#endif /* CONFIG_64BIT */
+
+#include <asm/mach-generic/spaces.h>
+#endif
@@ -44,11 +44,8 @@
#define cpu_has_vtag_icache 0
#define cpu_has_watch 1
#define cpu_has_local_ebase 0
-
-#ifdef CONFIG_CPU_LOONGSON64
#define cpu_has_wsbh 1
#define cpu_has_ic_fills_f_dc 1
#define cpu_hwrena_impl_bits 0xc0000000
-#endif
#endif /* __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H */
@@ -2,10 +2,9 @@
#ifndef __ASM_MACH_LOONGSON64_IRQ_H_
#define __ASM_MACH_LOONGSON64_IRQ_H_
+#include <loongson64.h>
#include <boot_param.h>
-#ifdef CONFIG_CPU_LOONGSON64
-
/* cpu core interrupt numbers */
#define MIPS_CPU_IRQ_BASE 56
@@ -35,10 +34,8 @@
#define LOONGSON_INT_COREx_INTy(x, y) (1<<(x) | 1<<(y+4)) /* route to int y of core x */
-#endif
-
extern void fixup_irqs(void);
-extern void loongson3_ipi_interrupt(struct pt_regs *regs);
+extern void loongson3_ipi_interrupt(void);
#include_next <irq.h>
#endif /* __ASM_MACH_LOONGSON64_IRQ_H_ */
deleted file mode 100644
@@ -1,74 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2005 Embedded Alley Solutions, Inc
- * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
- * Copyright (C) 2009 Jiajie Chen (chenjiajie@cse.buaa.edu.cn)
- * Copyright (C) 2012 Huacai Chen (chenhc@lemote.com)
- */
-#ifndef __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H
-#define __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H
-
-#include <asm/cpu.h>
-
-/*
- * Override macros used in arch/mips/kernel/head.S.
- */
- .macro kernel_entry_setup
-#ifdef CONFIG_CPU_LOONGSON64
- .set push
- .set mips64
- /* Set LPA on LOONGSON3 config3 */
- mfc0 t0, CP0_CONFIG3
- or t0, (0x1 << 7)
- mtc0 t0, CP0_CONFIG3
- /* Set ELPA on LOONGSON3 pagegrain */
- mfc0 t0, CP0_PAGEGRAIN
- or t0, (0x1 << 29)
- mtc0 t0, CP0_PAGEGRAIN
- /* Enable STFill Buffer */
- mfc0 t0, CP0_PRID
- andi t0, (PRID_IMP_MASK | PRID_REV_MASK)
- slti t0, (PRID_IMP_LOONGSON_64 | PRID_REV_LOONGSON3A_R2_0)
- bnez t0, 1f
- mfc0 t0, CP0_CONFIG6
- or t0, 0x100
- mtc0 t0, CP0_CONFIG6
-1:
- _ehb
- .set pop
-#endif
- .endm
-
-/*
- * Do SMP slave processor setup.
- */
- .macro smp_slave_setup
-#ifdef CONFIG_CPU_LOONGSON64
- .set push
- .set mips64
- /* Set LPA on LOONGSON3 config3 */
- mfc0 t0, CP0_CONFIG3
- or t0, (0x1 << 7)
- mtc0 t0, CP0_CONFIG3
- /* Set ELPA on LOONGSON3 pagegrain */
- mfc0 t0, CP0_PAGEGRAIN
- or t0, (0x1 << 29)
- mtc0 t0, CP0_PAGEGRAIN
- /* Enable STFill Buffer */
- mfc0 t0, CP0_PRID
- andi t0, (PRID_IMP_MASK | PRID_REV_MASK)
- slti t0, (PRID_IMP_LOONGSON_64 | PRID_REV_LOONGSON3A_R2_0)
- bnez t0, 1f
- mfc0 t0, CP0_CONFIG6
- or t0, 0x100
- mtc0 t0, CP0_CONFIG6
-1:
- _ehb
- .set pop
-#endif
- .endm
-
-#endif /* __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H */
new file mode 100644
@@ -0,0 +1,48 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2019 Jiaxun Yang <jiaxun.yang@flygoat.com>
+ *
+ * Generic definitions for MACH_LOONGSON64
+ */
+
+#ifndef __ASM_MACH_LOONGSON64_LOONGSON64_H
+#define __ASM_MACH_LOONGSON64_LOONGSON64_H
+
+#include <linux/types.h>
+#include <linux/init.h>
+
+#define MAX_PACKAGES 4
+
+#define LOONGSON_REG_BASE 0x1fe00000
+#define LOONGSON_REGBASE 0x100
+
+#define LOONGSON3_REG_BASE 0x3ff00000
+#define LOONGSON3_REG_SIZE 0x00100000 /* 256Bytes + 256Bytes + ??? */
+#define LOONGSON3_REG_TOP (LOONGSON3_REG_BASE+LOONGSON3_REG_SIZE-1)
+
+#define LOONGSON_REG(x) \
+ (*(volatile u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
+
+#define LOONGSON3_REG8(base, x) \
+ (*(volatile u8 *)((char *)TO_UNCAC(base) + (x)))
+
+#define LOONGSON3_REG32(base, x) \
+ (*(volatile u32 *)((char *)TO_UNCAC(base) + (x)))/* Loongson-3 specific registers */
+
+#define LOONGSON_PCIIO_SIZE 0x00100000 /* 1M */
+
+/* Chip Config registor of each physical cpu package, PRid >= Loongson-2F */
+extern u64 loongson_chipcfg[MAX_PACKAGES];
+#define LOONGSON_CHIPCFG(id) (*(volatile u32 *)(loongson_chipcfg[id]))
+
+/* Chip Temperature registor of each physical cpu package, PRid >= Loongson-3A */
+extern u64 loongson_chiptemp[MAX_PACKAGES];
+#define LOONGSON_CHIPTEMP(id) (*(volatile u32 *)(loongson_chiptemp[id]))
+
+/* Freq Control register of each physical cpu package, PRid >= Loongson-3B */
+extern u64 loongson_freqctrl[MAX_PACKAGES];
+#define LOONGSON_FREQCTRL(id) (*(volatile u32 *)(loongson_freqctrl[id]))
+
+extern const struct plat_smp_ops loongson3_smp_ops;
+extern void __init prom_init_lefi(void);
+#endif
@@ -19,30 +19,14 @@
#define pa_to_nid(addr) (((addr) & 0xf00000000000) >> NODE_ADDRSPACE_SHIFT)
#define nid_to_addrbase(nid) ((nid) << NODE_ADDRSPACE_SHIFT)
-#define LEVELS_PER_SLICE 128
-
-struct slice_data {
- unsigned long irq_enable_mask[2];
- int level_to_irq[LEVELS_PER_SLICE];
-};
-
-struct hub_data {
- cpumask_t h_cpus;
- unsigned long slice_map;
- unsigned long irq_alloc_mask[2];
- struct slice_data slice[2];
-};
-
struct node_data {
struct pglist_data pglist;
- struct hub_data hub;
cpumask_t cpumask;
};
extern struct node_data *__node_data[];
#define NODE_DATA(n) (&__node_data[(n)]->pglist)
-#define hub_data(n) (&__node_data[(n)]->hub)
extern void setup_zero_pages(void);
extern void __init prom_init_numa_memory(void);
@@ -4,47 +4,12 @@
* Copyright (c) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
*/
-#ifndef __ASM_MACH_LOONGSON64_PCI_H_
-#define __ASM_MACH_LOONGSON64_PCI_H_
+#ifndef __ASM_MACH_LOONGSON2EF_PCI_H_
+#define __ASM_MACH_LOONGSON2EF_PCI_H_
extern struct pci_ops loongson_pci_ops;
-/* this is an offset from mips_io_port_base */
-#define LOONGSON_PCI_IO_START 0x00004000UL
-
-#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
-
-/*
- * we use address window2 to map cpu address space to pci space
- * window2: cpu [1G, 2G] -> pci [1G, 2G]
- * why not use window 0 & 1? because they are used by cpu when booting.
- * window0: cpu [0, 256M] -> ddr [0, 256M]
- * window1: cpu [256M, 512M] -> pci [256M, 512M]
- */
-
-/* the smallest LOONGSON_CPU_MEM_SRC can be 512M */
-#define LOONGSON_CPU_MEM_SRC 0x40000000ul /* 1G */
-#define LOONGSON_PCI_MEM_DST LOONGSON_CPU_MEM_SRC
-
-#define LOONGSON_PCI_MEM_START LOONGSON_PCI_MEM_DST
-#define LOONGSON_PCI_MEM_END (0x80000000ul-1) /* 2G */
-
-#define MMAP_CPUTOPCI_SIZE (LOONGSON_PCI_MEM_END - \
- LOONGSON_PCI_MEM_START + 1)
-
-#else /* loongson2f/32bit & loongson2e */
-
-/* this pci memory space is mapped by pcimap in pci.c */
-#ifdef CONFIG_CPU_LOONGSON64
#define LOONGSON_PCI_MEM_START 0x40000000UL
#define LOONGSON_PCI_MEM_END 0x7effffffUL
-#else
-#define LOONGSON_PCI_MEM_START LOONGSON_PCILO1_BASE
-#define LOONGSON_PCI_MEM_END (LOONGSON_PCILO1_BASE + 0x04000000 * 2)
-#endif
-/* this is an offset from mips_io_port_base */
-#define LOONGSON_PCI_IO_START 0x00004000UL
-
-#endif /* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
-#endif /* !__ASM_MACH_LOONGSON64_PCI_H_ */
+#endif /* !__ASM_MACH_LOONGSON2EF_PCI_H_ */
@@ -2,7 +2,7 @@
#ifndef __ASM_MACH_LOONGSON64_WORKAROUNDS_H_
#define __ASM_MACH_LOONGSON64_WORKAROUNDS_H_
-#define WORKAROUND_CPUFREQ 0x00000001
-#define WORKAROUND_CPUHOTPLUG 0x00000002
+#define WORKAROUND_CPUFREQ BIT(1)
+#define WORKAROUND_CPUHOTPLUG BIT(2)
#endif
new file mode 100644
@@ -0,0 +1,93 @@
+# SPDX-License-Identifier: GPL-2.0
+if MACH_LOONGSON2EF
+
+choice
+ prompt "Machine Type"
+
+config LEMOTE_FULOONG2E
+ bool "Lemote Fuloong(2e) mini-PC"
+ select ARCH_SPARSEMEM_ENABLE
+ select ARCH_MIGHT_HAVE_PC_PARPORT
+ select ARCH_MIGHT_HAVE_PC_SERIO
+ select CEVT_R4K
+ select CSRC_R4K
+ select SYS_HAS_CPU_LOONGSON2E
+ select DMA_NONCOHERENT
+ select BOOT_ELF32
+ select BOARD_SCACHE
+ select HAVE_PCI
+ select I8259
+ select ISA
+ select IRQ_MIPS_CPU
+ select SYS_SUPPORTS_64BIT_KERNEL
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_HIGHMEM
+ select SYS_HAS_EARLY_PRINTK
+ select GENERIC_ISA_DMA_SUPPORT_BROKEN
+ select CPU_HAS_WB
+ select LOONGSON_MC146818
+ help
+ Lemote Fuloong(2e) mini-PC board based on the Chinese Loongson-2E CPU and
+ an FPGA northbridge
+
+ Lemote Fuloong(2e) mini PC have a VIA686B south bridge.
+
+config LEMOTE_MACH2F
+ bool "Lemote Loongson 2F family machines"
+ select ARCH_SPARSEMEM_ENABLE
+ select ARCH_MIGHT_HAVE_PC_PARPORT
+ select ARCH_MIGHT_HAVE_PC_SERIO
+ select BOARD_SCACHE
+ select BOOT_ELF32
+ select CEVT_R4K if ! MIPS_EXTERNAL_TIMER
+ select CPU_HAS_WB
+ select CS5536
+ select CSRC_R4K if ! MIPS_EXTERNAL_TIMER
+ select DMA_NONCOHERENT
+ select GENERIC_ISA_DMA_SUPPORT_BROKEN
+ select HAVE_CLK
+ select HAVE_PCI
+ select I8259
+ select IRQ_MIPS_CPU
+ select ISA
+ select SYS_HAS_CPU_LOONGSON2F
+ select SYS_HAS_EARLY_PRINTK
+ select SYS_SUPPORTS_64BIT_KERNEL
+ select SYS_SUPPORTS_HIGHMEM
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select LOONGSON_MC146818
+ help
+ Lemote Loongson 2F family machines utilize the 2F revision of
+ Loongson processor and the AMD CS5536 south bridge.
+
+ These family machines include fuloong2f mini PC, yeeloong2f notebook,
+ LingLoong allinone PC and so forth.
+
+endchoice
+
+config CS5536
+ bool
+
+config CS5536_MFGPT
+ bool "CS5536 MFGPT Timer"
+ depends on CS5536 && !HIGH_RES_TIMERS
+ select MIPS_EXTERNAL_TIMER
+ help
+ This option enables the mfgpt0 timer of AMD CS5536. With this timer
+ switched on you can not use high resolution timers.
+
+ If you want to enable the Loongson2 CPUFreq Driver, Please enable
+ this option at first, otherwise, You will get wrong system time.
+
+ If unsure, say Yes.
+
+config LOONGSON_UART_BASE
+ bool
+ default y
+ depends on EARLY_PRINTK || SERIAL_8250
+
+config LOONGSON_MC146818
+ bool
+ default n
+
+endif # MACH_LOONGSON2EF
new file mode 100644
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Common code for all Loongson based systems
+#
+
+obj-y += common/
+
+#
+# Lemote Fuloong mini-PC (Loongson 2E-based)
+#
+
+obj-$(CONFIG_LEMOTE_FULOONG2E) += fuloong-2e/
+
+#
+# Lemote loongson2f family machines
+#
+
+obj-$(CONFIG_LEMOTE_MACH2F) += lemote-2f/
new file mode 100644
@@ -0,0 +1,32 @@
+#
+# Loongson Processors' Support
+#
+
+# Only gcc >= 4.4 have Loongson specific support
+cflags-$(CONFIG_CPU_LOONGSON2EF) += -Wa,--trap
+cflags-$(CONFIG_CPU_LOONGSON2E) += \
+ $(call cc-option,-march=loongson2e,-march=r4600)
+cflags-$(CONFIG_CPU_LOONGSON2F) += \
+ $(call cc-option,-march=loongson2f,-march=r4600)
+# Enable the workarounds for Loongson2f
+ifdef CONFIG_CPU_LOONGSON2F_WORKAROUNDS
+ ifeq ($(call as-option,-Wa$(comma)-mfix-loongson2f-nop,),)
+ $(error only binutils >= 2.20.2 have needed option -mfix-loongson2f-nop)
+ else
+ cflags-$(CONFIG_CPU_NOP_WORKAROUNDS) += -Wa$(comma)-mfix-loongson2f-nop
+ endif
+ ifeq ($(call as-option,-Wa$(comma)-mfix-loongson2f-jump,),)
+ $(error only binutils >= 2.20.2 have needed option -mfix-loongson2f-jump)
+ else
+ cflags-$(CONFIG_CPU_JUMP_WORKAROUNDS) += -Wa$(comma)-mfix-loongson2f-jump
+ endif
+endif
+
+#
+# Loongson Machines' Support
+#
+
+platform-$(CONFIG_MACH_LOONGSON2EF) += loongson2ef/
+cflags-$(CONFIG_MACH_LOONGSON2EF) += -I$(srctree)/arch/mips/include/asm/mach-loongson2ef -mno-branch-likely
+load-$(CONFIG_LEMOTE_FULOONG2E) += 0xffffffff80100000
+load-$(CONFIG_LEMOTE_MACH2F) += 0xffffffff80200000
similarity index 100%
rename from arch/mips/loongson64/common/Makefile
rename to arch/mips/loongson2ef/common/Makefile
similarity index 97%
rename from arch/mips/loongson64/common/bonito-irq.c
rename to arch/mips/loongson2ef/common/bonito-irq.c
@@ -10,7 +10,7 @@
#include <linux/interrupt.h>
#include <linux/compiler.h>
-#include <loongson.h>
+#include <loongson2ef.h>
static inline void bonito_irq_enable(struct irq_data *d)
{
similarity index 97%
rename from arch/mips/loongson64/common/cmdline.c
rename to arch/mips/loongson2ef/common/cmdline.c
@@ -15,7 +15,7 @@
*/
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
void __init prom_init_cmdline(void)
{
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/Makefile
rename to arch/mips/loongson2ef/common/cs5536/Makefile
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_acc.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_acc.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_ehci.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_ehci.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_ide.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_ide.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_isa.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_isa.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_mfgpt.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_mfgpt.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_ohci.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_ohci.c
similarity index 100%
rename from arch/mips/loongson64/common/cs5536/cs5536_pci.c
rename to arch/mips/loongson2ef/common/cs5536/cs5536_pci.c
similarity index 97%
rename from arch/mips/loongson64/common/early_printk.c
rename to arch/mips/loongson2ef/common/early_printk.c
@@ -8,7 +8,7 @@
#include <linux/serial_reg.h>
#include <asm/setup.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#define PORT(base, offset) (u8 *)(base + offset)
new file mode 100644
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Based on Ocelot Linux port, which is
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ *
+ * Copyright 2003 ICT CAS
+ * Author: Michael Guo <guoyi@ict.ac.cn>
+ *
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+#include <linux/export.h>
+#include <asm/bootinfo.h>
+#include <loongson2ef.h>
+
+u32 cpu_clock_freq;
+EXPORT_SYMBOL(cpu_clock_freq);
+
+unsigned long long smp_group[4];
+
+#define parse_even_earlier(res, option, p) \
+do { \
+ unsigned int tmp __maybe_unused; \
+ \
+ if (strncmp(option, (char *)p, strlen(option)) == 0) \
+ tmp = kstrtou32((char *)p + strlen(option"="), 10, &res); \
+} while (0)
+
+void __init prom_init_env(void)
+{
+ /* pmon passes arguments in 32bit pointers */
+ unsigned int processor_id;
+ int *_prom_envp;
+ long l;
+
+ /* firmware arguments are initialized in head.S */
+ _prom_envp = (int *)fw_arg2;
+
+ l = (long)*_prom_envp;
+ while (l != 0) {
+ parse_even_earlier(cpu_clock_freq, "cpuclock", l);
+ parse_even_earlier(memsize, "memsize", l);
+ parse_even_earlier(highmemsize, "highmemsize", l);
+ _prom_envp++;
+ l = (long)*_prom_envp;
+ }
+ if (memsize == 0)
+ memsize = 256;
+
+ pr_info("memsize=%u, highmemsize=%u\n", memsize, highmemsize);
+
+ if (cpu_clock_freq == 0) {
+ processor_id = (¤t_cpu_data)->processor_id;
+ switch (processor_id & PRID_REV_MASK) {
+ case PRID_REV_LOONGSON2E:
+ cpu_clock_freq = 533080000;
+ break;
+ case PRID_REV_LOONGSON2F:
+ cpu_clock_freq = 797000000;
+ break;
+ default:
+ cpu_clock_freq = 100000000;
+ break;
+ }
+ }
+ pr_info("CpuClock = %u\n", cpu_clock_freq);
+}
similarity index 90%
rename from arch/mips/loongson64/common/init.c
rename to arch/mips/loongson2ef/common/init.c
@@ -10,7 +10,7 @@
#include <asm/smp-ops.h>
#include <asm/cacheflush.h>
-#include <loongson.h>
+#include <loongson2ef.h>
/* Loongson CPU address windows config space base address */
unsigned long __maybe_unused _loongson_addrwincfg_base;
@@ -39,15 +39,10 @@ void __init prom_init(void)
set_io_port_base((unsigned long)
ioremap(LOONGSON_PCIIO_BASE, LOONGSON_PCIIO_SIZE));
-#ifdef CONFIG_NUMA
- prom_init_numa_memory();
-#else
prom_init_memory();
-#endif
/*init the uart base address */
prom_init_uart_base();
- register_smp_ops(&loongson3_smp_ops);
board_nmi_handler_setup = mips_nmi_setup;
}
similarity index 98%
rename from arch/mips/loongson64/common/irq.c
rename to arch/mips/loongson2ef/common/irq.c
@@ -6,7 +6,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
-#include <loongson.h>
+#include <loongson2ef.h>
/*
* the first level int-handler will jump here if it is a bonito irq
*/
similarity index 94%
rename from arch/mips/loongson64/common/machtype.c
rename to arch/mips/loongson2ef/common/machtype.c
@@ -8,7 +8,7 @@
#include <linux/errno.h>
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <machine.h>
/* please ensure the length of the machtype string is less than 50 */
@@ -23,7 +23,6 @@ static const char *system_types[] = {
[MACH_DEXXON_GDIUM2F10] = "dexxon-gdium-2f",
[MACH_LEMOTE_NAS] = "lemote-nas-2f",
[MACH_LEMOTE_LL2F] = "lemote-lynloong-2f",
- [MACH_LOONGSON_GENERIC] = "generic-loongson-machine",
[MACH_LOONGSON_END] = NULL,
};
similarity index 72%
rename from arch/mips/loongson64/common/mem.c
rename to arch/mips/loongson2ef/common/mem.c
@@ -7,12 +7,10 @@
#include <asm/bootinfo.h>
-#include <loongson.h>
-#include <boot_param.h>
+#include <loongson2ef.h>
#include <mem.h>
#include <pci.h>
-#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
u32 memsize, highmemsize;
@@ -51,42 +49,6 @@ void __init prom_init_memory(void)
#endif /* !CONFIG_64BIT */
}
-#else /* CONFIG_LEFI_FIRMWARE_INTERFACE */
-
-void __init prom_init_memory(void)
-{
- int i;
- u32 node_id;
- u32 mem_type;
-
- /* parse memory information */
- for (i = 0; i < loongson_memmap->nr_map; i++) {
- node_id = loongson_memmap->map[i].node_id;
- mem_type = loongson_memmap->map[i].mem_type;
-
- if (node_id == 0) {
- switch (mem_type) {
- case SYSTEM_RAM_LOW:
- add_memory_region(loongson_memmap->map[i].mem_start,
- (u64)loongson_memmap->map[i].mem_size << 20,
- BOOT_MEM_RAM);
- break;
- case SYSTEM_RAM_HIGH:
- add_memory_region(loongson_memmap->map[i].mem_start,
- (u64)loongson_memmap->map[i].mem_size << 20,
- BOOT_MEM_RAM);
- break;
- case SYSTEM_RAM_RESERVED:
- add_memory_region(loongson_memmap->map[i].mem_start,
- (u64)loongson_memmap->map[i].mem_size << 20,
- BOOT_MEM_RESERVED);
- break;
- }
- }
- }
-}
-
-#endif /* CONFIG_LEFI_FIRMWARE_INTERFACE */
/* override of arch/mips/mm/cache.c: __uncached_access */
int __uncached_access(struct file *file, unsigned long addr)
similarity index 89%
rename from arch/mips/loongson64/common/pci.c
rename to arch/mips/loongson2ef/common/pci.c
@@ -6,8 +6,7 @@
#include <linux/pci.h>
#include <pci.h>
-#include <loongson.h>
-#include <boot_param.h>
+#include <loongson2ef.h>
static struct resource loongson_pci_mem_resource = {
.name = "pci memory space",
@@ -81,16 +80,8 @@ static int __init pcibios_init(void)
setup_pcimap();
loongson_pci_controller.io_map_base = mips_io_port_base;
-#ifdef CONFIG_LEFI_FIRMWARE_INTERFACE
- loongson_pci_mem_resource.start = loongson_sysconf.pci_mem_start_addr;
- loongson_pci_mem_resource.end = loongson_sysconf.pci_mem_end_addr;
-#endif
register_pci_controller(&loongson_pci_controller);
-#ifdef CONFIG_CPU_LOONGSON64
- sbx00_acpi_init();
-#endif
-
return 0;
}
similarity index 100%
rename from arch/mips/loongson64/common/platform.c
rename to arch/mips/loongson2ef/common/platform.c
similarity index 99%
rename from arch/mips/loongson64/common/pm.c
rename to arch/mips/loongson2ef/common/pm.c
@@ -12,7 +12,7 @@
#include <asm/i8259.h>
#include <asm/mipsregs.h>
-#include <loongson.h>
+#include <loongson2ef.h>
static unsigned int __maybe_unused cached_master_mask; /* i8259A */
static unsigned int __maybe_unused cached_slave_mask;
similarity index 77%
rename from arch/mips/loongson64/common/reset.c
rename to arch/mips/loongson2ef/common/reset.c
@@ -12,8 +12,7 @@
#include <asm/idle.h>
#include <asm/reboot.h>
-#include <loongson.h>
-#include <boot_param.h>
+#include <loongson2ef.h>
static inline void loongson_reboot(void)
{
@@ -35,26 +34,15 @@ static inline void loongson_reboot(void)
static void loongson_restart(char *command)
{
-#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
/* do preparation for reboot */
mach_prepare_reboot();
/* reboot via jumping to boot base address */
loongson_reboot();
-#else
- void (*fw_restart)(void) = (void *)loongson_sysconf.restart_addr;
-
- fw_restart();
- while (1) {
- if (cpu_wait)
- cpu_wait();
- }
-#endif
}
static void loongson_poweroff(void)
{
-#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
mach_prepare_shutdown();
/*
@@ -62,15 +50,6 @@ static void loongson_poweroff(void)
* a generic delay loop, machine_hang(), so simply return.
*/
return;
-#else
- void (*fw_poweroff)(void) = (void *)loongson_sysconf.poweroff_addr;
-
- fw_poweroff();
- while (1) {
- if (cpu_wait)
- cpu_wait();
- }
-#endif
}
static void loongson_halt(void)
similarity index 100%
rename from arch/mips/loongson64/common/rtc.c
rename to arch/mips/loongson2ef/common/rtc.c
similarity index 63%
rename from arch/mips/loongson64/common/serial.c
rename to arch/mips/loongson2ef/common/serial.c
@@ -16,7 +16,7 @@
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <machine.h>
#define PORT(int, clk) \
@@ -38,7 +38,7 @@
.regshift = 0, \
}
-static struct plat_serial8250_port uart8250_data[][MAX_UARTS + 1] = {
+static struct plat_serial8250_port uart8250_data[][16] = {
[MACH_LOONGSON_UNKNOWN] = {},
[MACH_LEMOTE_FL2E] = {PORT(4, 1843200), {} },
[MACH_LEMOTE_FL2F] = {PORT(3, 1843200), {} },
@@ -47,7 +47,6 @@ static struct plat_serial8250_port uart8250_data[][MAX_UARTS + 1] = {
[MACH_DEXXON_GDIUM2F10] = {PORT_M(3, 3686400), {} },
[MACH_LEMOTE_NAS] = {PORT_M(3, 3686400), {} },
[MACH_LEMOTE_LL2F] = {PORT(3, 1843200), {} },
- [MACH_LOONGSON_GENERIC] = {PORT_M(2, 25000000), {} },
[MACH_LOONGSON_END] = {},
};
@@ -58,7 +57,6 @@ static struct platform_device uart8250_device = {
static int __init serial_init(void)
{
- int i;
unsigned char iotype;
iotype = uart8250_data[mips_machtype][0].iotype;
@@ -73,36 +71,7 @@ static int __init serial_init(void)
uart8250_data[mips_machtype][0].iobase =
loongson_uart_base[0] - LOONGSON_PCIIO_BASE;
- if (loongson_sysconf.uarts[0].uartclk)
- uart8250_data[mips_machtype][0].uartclk =
- loongson_sysconf.uarts[0].uartclk;
-
- for (i = 1; i < loongson_sysconf.nr_uarts; i++) {
- iotype = loongson_sysconf.uarts[i].iotype;
- uart8250_data[mips_machtype][i].iotype = iotype;
- loongson_uart_base[i] = loongson_sysconf.uarts[i].uart_base;
-
- if (UPIO_MEM == iotype) {
- uart8250_data[mips_machtype][i].irq =
- MIPS_CPU_IRQ_BASE + loongson_sysconf.uarts[i].int_offset;
- uart8250_data[mips_machtype][i].mapbase =
- loongson_uart_base[i];
- uart8250_data[mips_machtype][i].membase =
- ioremap_nocache(loongson_uart_base[i], 8);
- } else if (UPIO_PORT == iotype) {
- uart8250_data[mips_machtype][i].irq =
- loongson_sysconf.uarts[i].int_offset;
- uart8250_data[mips_machtype][i].iobase =
- loongson_uart_base[i] - LOONGSON_PCIIO_BASE;
- }
-
- uart8250_data[mips_machtype][i].uartclk =
- loongson_sysconf.uarts[i].uartclk;
- uart8250_data[mips_machtype][i].flags =
- UPF_BOOT_AUTOCONF | UPF_SKIP_TEST;
- }
-
- memset(&uart8250_data[mips_machtype][loongson_sysconf.nr_uarts],
+ memset(&uart8250_data[mips_machtype][1],
0, sizeof(struct plat_serial8250_port));
uart8250_device.dev.platform_data = uart8250_data[mips_machtype];
similarity index 97%
rename from arch/mips/loongson64/common/setup.c
rename to arch/mips/loongson2ef/common/setup.c
@@ -9,7 +9,7 @@
#include <asm/wbflush.h>
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#ifdef CONFIG_VT
#include <linux/console.h>
similarity index 96%
rename from arch/mips/loongson64/common/time.c
rename to arch/mips/loongson2ef/common/time.c
@@ -10,7 +10,7 @@
#include <asm/time.h>
#include <asm/hpet.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <cs5536/cs5536_mfgpt.h>
void __init plat_time_init(void)
similarity index 77%
rename from arch/mips/loongson64/common/uart_base.c
rename to arch/mips/loongson2ef/common/uart_base.c
@@ -7,12 +7,12 @@
#include <linux/export.h>
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
/* raw */
-unsigned long loongson_uart_base[MAX_UARTS] = {};
+unsigned long loongson_uart_base[16] = {};
/* ioremapped */
-unsigned long _loongson_uart_base[MAX_UARTS] = {};
+unsigned long _loongson_uart_base[16] = {};
EXPORT_SYMBOL(loongson_uart_base);
EXPORT_SYMBOL(_loongson_uart_base);
@@ -20,10 +20,6 @@ EXPORT_SYMBOL(_loongson_uart_base);
void prom_init_loongson_uart_base(void)
{
switch (mips_machtype) {
- case MACH_LOONGSON_GENERIC:
- /* The CPU provided serial port (CPU) */
- loongson_uart_base[0] = LOONGSON_REG_BASE + 0x1e0;
- break;
case MACH_LEMOTE_FL2E:
loongson_uart_base[0] = LOONGSON_PCIIO_BASE + 0x3f8;
break;
similarity index 100%
rename from arch/mips/loongson64/fuloong-2e/Makefile
rename to arch/mips/loongson2ef/fuloong-2e/Makefile
similarity index 100%
rename from arch/mips/loongson64/fuloong-2e/dma.c
rename to arch/mips/loongson2ef/fuloong-2e/dma.c
similarity index 98%
rename from arch/mips/loongson64/fuloong-2e/irq.c
rename to arch/mips/loongson2ef/fuloong-2e/irq.c
@@ -8,7 +8,7 @@
#include <asm/irq_cpu.h>
#include <asm/i8259.h>
-#include <loongson.h>
+#include <loongson2ef.h>
static void i8259_irqdispatch(void)
{
similarity index 93%
rename from arch/mips/loongson64/fuloong-2e/reset.c
rename to arch/mips/loongson2ef/fuloong-2e/reset.c
@@ -6,7 +6,7 @@
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*/
-#include <loongson.h>
+#include <loongson2ef.h>
void mach_prepare_reboot(void)
{
similarity index 100%
rename from arch/mips/loongson64/lemote-2f/Makefile
rename to arch/mips/loongson2ef/lemote-2f/Makefile
similarity index 98%
rename from arch/mips/loongson64/lemote-2f/clock.c
rename to arch/mips/loongson2ef/lemote-2f/clock.c
@@ -15,7 +15,7 @@
#include <linux/spinlock.h>
#include <asm/clock.h>
-#include <asm/mach-loongson64/loongson.h>
+#include <asm/mach-loongson2ef/loongson2ef.h>
static LIST_HEAD(clock_list);
static DEFINE_SPINLOCK(clock_lock);
similarity index 100%
rename from arch/mips/loongson64/lemote-2f/dma.c
rename to arch/mips/loongson2ef/lemote-2f/dma.c
similarity index 100%
rename from arch/mips/loongson64/lemote-2f/ec_kb3310b.c
rename to arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c
similarity index 100%
rename from arch/mips/loongson64/lemote-2f/ec_kb3310b.h
rename to arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h
similarity index 99%
rename from arch/mips/loongson64/lemote-2f/irq.c
rename to arch/mips/loongson2ef/lemote-2f/irq.c
@@ -12,7 +12,7 @@
#include <asm/i8259.h>
#include <asm/mipsregs.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <machine.h>
#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7) /* cpu timer */
similarity index 98%
rename from arch/mips/loongson64/lemote-2f/machtype.c
rename to arch/mips/loongson2ef/lemote-2f/machtype.c
@@ -5,7 +5,7 @@
*/
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
void __init mach_prom_init_machtype(void)
{
similarity index 99%
rename from arch/mips/loongson64/lemote-2f/pm.c
rename to arch/mips/loongson2ef/lemote-2f/pm.c
@@ -16,7 +16,7 @@
#include <asm/mipsregs.h>
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <cs5536/cs5536_mfgpt.h>
#include "ec_kb3310b.h"
similarity index 99%
rename from arch/mips/loongson64/lemote-2f/reset.c
rename to arch/mips/loongson2ef/lemote-2f/reset.c
@@ -13,7 +13,7 @@
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <cs5536/cs5536.h>
#include "ec_kb3310b.h"
@@ -1,119 +1,9 @@
# SPDX-License-Identifier: GPL-2.0
if MACH_LOONGSON64
-choice
- prompt "Machine Type"
-
-config LEMOTE_FULOONG2E
- bool "Lemote Fuloong(2e) mini-PC"
- select ARCH_SPARSEMEM_ENABLE
- select ARCH_MIGHT_HAVE_PC_PARPORT
- select ARCH_MIGHT_HAVE_PC_SERIO
- select CEVT_R4K
- select CSRC_R4K
- select SYS_HAS_CPU_LOONGSON2E
- select DMA_NONCOHERENT
- select BOOT_ELF32
- select BOARD_SCACHE
- select HAVE_PCI
- select I8259
- select ISA
- select IRQ_MIPS_CPU
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_HIGHMEM
- select SYS_HAS_EARLY_PRINTK
- select GENERIC_ISA_DMA_SUPPORT_BROKEN
- select CPU_HAS_WB
- select LOONGSON_MC146818
- help
- Lemote Fuloong(2e) mini-PC board based on the Chinese Loongson-2E CPU and
- an FPGA northbridge
-
- Lemote Fuloong(2e) mini PC have a VIA686B south bridge.
-
-config LEMOTE_MACH2F
- bool "Lemote Loongson 2F family machines"
- select ARCH_SPARSEMEM_ENABLE
- select ARCH_MIGHT_HAVE_PC_PARPORT
- select ARCH_MIGHT_HAVE_PC_SERIO
- select BOARD_SCACHE
- select BOOT_ELF32
- select CEVT_R4K if ! MIPS_EXTERNAL_TIMER
- select CPU_HAS_WB
- select CS5536
- select CSRC_R4K if ! MIPS_EXTERNAL_TIMER
- select DMA_NONCOHERENT
- select GENERIC_ISA_DMA_SUPPORT_BROKEN
- select HAVE_CLK
- select HAVE_PCI
- select I8259
- select IRQ_MIPS_CPU
- select ISA
- select SYS_HAS_CPU_LOONGSON2F
- select SYS_HAS_EARLY_PRINTK
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select LOONGSON_MC146818
- help
- Lemote Loongson 2F family machines utilize the 2F revision of
- Loongson processor and the AMD CS5536 south bridge.
-
- These family machines include fuloong2f mini PC, yeeloong2f notebook,
- LingLoong allinone PC and so forth.
-
-config LOONGSON_MACH3X
- bool "Generic Loongson 3 family machines"
- select ARCH_SPARSEMEM_ENABLE
- select ARCH_MIGHT_HAVE_PC_PARPORT
- select ARCH_MIGHT_HAVE_PC_SERIO
- select GENERIC_ISA_DMA_SUPPORT_BROKEN
- select BOOT_ELF32
- select BOARD_SCACHE
- select CSRC_R4K
- select CEVT_R4K
- select CPU_HAS_WB
- select FORCE_PCI
- select ISA
- select I8259
- select IRQ_MIPS_CPU
- select NR_CPUS_DEFAULT_4
- select SYS_HAS_CPU_LOONGSON64
- select SYS_HAS_EARLY_PRINTK
- select SYS_SUPPORTS_SMP
- select SYS_SUPPORTS_HOTPLUG_CPU
- select SYS_SUPPORTS_NUMA
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select LOONGSON_MC146818
- select ZONE_DMA32
- select LEFI_FIRMWARE_INTERFACE
- help
- Generic Loongson 3 family machines utilize the 3A/3B revision
- of Loongson processor and RS780/SBX00 chipset.
-endchoice
-
-config CS5536
- bool
-
-config CS5536_MFGPT
- bool "CS5536 MFGPT Timer"
- depends on CS5536 && !HIGH_RES_TIMERS
- select MIPS_EXTERNAL_TIMER
- help
- This option enables the mfgpt0 timer of AMD CS5536. With this timer
- switched on you can not use high resolution timers.
-
- If you want to enable the Loongson2 CPUFreq Driver, Please enable
- this option at first, otherwise, You will get wrong system time.
-
- If unsure, say Yes.
-
config RS780_HPET
bool "RS780/SBX00 HPET Timer"
- depends on LOONGSON_MACH3X
+ depends on MACH_LOONGSON64
select MIPS_EXTERNAL_TIMER
help
This option enables the hpet timer of AMD RS780/SBX00.
@@ -123,16 +13,4 @@ config RS780_HPET
If unsure, say Yes.
-config LOONGSON_UART_BASE
- bool
- default y
- depends on EARLY_PRINTK || SERIAL_8250
-
-config LOONGSON_MC146818
- bool
- default n
-
-config LEFI_FIRMWARE_INTERFACE
- bool
-
-endif # MACH_LOONGSON64
+endif
@@ -1,24 +1,11 @@
# SPDX-License-Identifier: GPL-2.0-only
#
-# Common code for all Loongson based systems
+# Makefile for Loongson64 family machines
#
+obj-y += irq.o cop2-ex.o platform.o acpi_init.o dma.o env.o platform.o reset.o setup.o pci.o
-obj-$(CONFIG_MACH_LOONGSON64) += common/
+obj-$(CONFIG_SMP) += smp.o
-#
-# Lemote Fuloong mini-PC (Loongson 2E-based)
-#
-
-obj-$(CONFIG_LEMOTE_FULOONG2E) += fuloong-2e/
-
-#
-# Lemote loongson2f family machines
-#
-
-obj-$(CONFIG_LEMOTE_MACH2F) += lemote-2f/
-
-#
-# All Loongson-3 family machines
-#
+obj-$(CONFIG_NUMA) += numa.o
-obj-$(CONFIG_CPU_LOONGSON64) += loongson-3/
+obj-$(CONFIG_RS780_HPET) += hpet.o
@@ -1,27 +1,7 @@
#
-# Loongson Processors' Support
+# Loongson64 Processors' Support
#
-# Only gcc >= 4.4 have Loongson specific support
-cflags-$(CONFIG_CPU_LOONGSON2EF) += -Wa,--trap
-cflags-$(CONFIG_CPU_LOONGSON2E) += \
- $(call cc-option,-march=loongson2e,-march=r4600)
-cflags-$(CONFIG_CPU_LOONGSON2F) += \
- $(call cc-option,-march=loongson2f,-march=r4600)
-# Enable the workarounds for Loongson2f
-ifdef CONFIG_CPU_LOONGSON2F_WORKAROUNDS
- ifeq ($(call as-option,-Wa$(comma)-mfix-loongson2f-nop,),)
- $(error only binutils >= 2.20.2 have needed option -mfix-loongson2f-nop)
- else
- cflags-$(CONFIG_CPU_NOP_WORKAROUNDS) += -Wa$(comma)-mfix-loongson2f-nop
- endif
- ifeq ($(call as-option,-Wa$(comma)-mfix-loongson2f-jump,),)
- $(error only binutils >= 2.20.2 have needed option -mfix-loongson2f-jump)
- else
- cflags-$(CONFIG_CPU_JUMP_WORKAROUNDS) += -Wa$(comma)-mfix-loongson2f-jump
- endif
-endif
-
cflags-$(CONFIG_CPU_LOONGSON64) += -Wa,--trap
#
@@ -72,6 +52,4 @@ endif
platform-$(CONFIG_MACH_LOONGSON64) += loongson64/
cflags-$(CONFIG_MACH_LOONGSON64) += -I$(srctree)/arch/mips/include/asm/mach-loongson64 -mno-branch-likely
-load-$(CONFIG_LEMOTE_FULOONG2E) += 0xffffffff80100000
-load-$(CONFIG_LEMOTE_MACH2F) += 0xffffffff80200000
-load-$(CONFIG_LOONGSON_MACH3X) += 0xffffffff80200000
+load-$(CONFIG_MACH_LOONGSON64) += 0xffffffff80200000
similarity index 99%
rename from arch/mips/loongson64/loongson-3/acpi_init.c
rename to arch/mips/loongson64/acpi_init.c
@@ -99,7 +99,8 @@ void acpi_registers_setup(void)
pm_iowrite(0x2f, ACPI_END >> 8);
/* IO Decode: When AcpiDecodeEnable set, South-Bridge uses the contents
- * of the PM registers at index 0x20~0x2B to decode ACPI I/O address. */
+ * of the PM registers at index 0x20~0x2B to decode ACPI I/O address.
+ */
pm_iowrite(0x0e, 1 << 3);
/* SCI_EN set */
similarity index 88%
rename from arch/mips/loongson64/loongson-3/cop2-ex.c
rename to arch/mips/loongson64/cop2-ex.c
@@ -1,8 +1,5 @@
+// SPDX-License-Identifier: GPL-2.0
/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
* Copyright (C) 2014 Lemote Corporation.
* written by Huacai Chen <chenhc@lemote.com>
*
similarity index 82%
rename from arch/mips/loongson64/loongson-3/dma.c
rename to arch/mips/loongson64/dma.c
@@ -6,7 +6,8 @@
dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
{
/* We extract 2bit node id (bit 44~47, only bit 44~45 used now) from
- * Loongson-3's 48bit address space and embed it into 40bit */
+ * Loongson-3's 48bit address space and embed it into 40bit
+ */
long nid = (paddr >> 44) & 0x3;
return ((nid << 44) ^ paddr) | (nid << 37);
}
@@ -14,7 +15,8 @@ dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t daddr)
{
/* We extract 2bit node id (bit 44~47, only bit 44~45 used now) from
- * Loongson-3's 48bit address space and embed it into 40bit */
+ * Loongson-3's 48bit address space and embed it into 40bit
+ */
long nid = (daddr >> 37) & 0x3;
return ((nid << 37) ^ daddr) | (nid << 44);
}
similarity index 79%
rename from arch/mips/loongson64/common/env.c
rename to arch/mips/loongson64/env.c
@@ -15,7 +15,10 @@
*/
#include <linux/export.h>
#include <asm/bootinfo.h>
-#include <loongson.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+
+#include <loongson64.h>
#include <boot_param.h>
#include <workarounds.h>
@@ -30,45 +33,17 @@ u64 loongson_freqctrl[MAX_PACKAGES];
unsigned long long smp_group[4];
-#define parse_even_earlier(res, option, p) \
-do { \
- unsigned int tmp __maybe_unused; \
- \
- if (strncmp(option, (char *)p, strlen(option)) == 0) \
- tmp = kstrtou32((char *)p + strlen(option"="), 10, &res); \
-} while (0)
-void __init prom_init_env(void)
+void __init prom_init_lefi(void)
{
/* pmon passes arguments in 32bit pointers */
unsigned int processor_id;
-#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
- int *_prom_envp;
- long l;
-
- /* firmware arguments are initialized in head.S */
- _prom_envp = (int *)fw_arg2;
-
- l = (long)*_prom_envp;
- while (l != 0) {
- parse_even_earlier(cpu_clock_freq, "cpuclock", l);
- parse_even_earlier(memsize, "memsize", l);
- parse_even_earlier(highmemsize, "highmemsize", l);
- _prom_envp++;
- l = (long)*_prom_envp;
- }
- if (memsize == 0)
- memsize = 256;
-
- loongson_sysconf.nr_uarts = 1;
-
- pr_info("memsize=%u, highmemsize=%u\n", memsize, highmemsize);
-#else
struct boot_params *boot_p;
struct loongson_params *loongson_p;
struct system_loongson *esys;
struct efi_cpuinfo_loongson *ecpu;
+ struct board_devices *eboard;
struct irq_source_routing_table *eirq_source;
/* firmware arguments are initialized in head.S */
@@ -79,12 +54,15 @@ void __init prom_init_env(void)
((u64)loongson_p + loongson_p->system_offset);
ecpu = (struct efi_cpuinfo_loongson *)
((u64)loongson_p + loongson_p->cpu_offset);
+ eboard = (struct board_devices *)
+ ((u64)loongson_p + loongson_p->boarddev_table_offset);
eirq_source = (struct irq_source_routing_table *)
((u64)loongson_p + loongson_p->irq_offset);
loongson_memmap = (struct efi_memory_map_loongson *)
((u64)loongson_p + loongson_p->memory_offset);
cpu_clock_freq = ecpu->cpu_clock_freq;
+ mips_hpt_frequency = cpu_clock_freq / 2;
loongson_sysconf.cputype = ecpu->cputype;
switch (ecpu->cputype) {
case Legacy_3A:
@@ -151,6 +129,7 @@ void __init prom_init_env(void)
loongson_sysconf.pci_mem_start_addr = eirq_source->pci_mem_start_addr;
loongson_sysconf.pci_mem_end_addr = eirq_source->pci_mem_end_addr;
loongson_sysconf.pci_io_base = eirq_source->pci_io_start_addr;
+ set_io_port_base(loongson_sysconf.pci_io_base);
loongson_sysconf.dma_mask_bits = eirq_source->dma_mask_bits;
if (loongson_sysconf.dma_mask_bits < 32 ||
loongson_sysconf.dma_mask_bits > 64)
@@ -165,6 +144,9 @@ void __init prom_init_env(void)
loongson_sysconf.poweroff_addr, loongson_sysconf.restart_addr,
loongson_sysconf.vgabios_addr);
+ if (eboard->name)
+ mips_set_machine_name(eboard->name);
+
memset(loongson_sysconf.ecname, 0, 32);
if (esys->has_ec)
memcpy(loongson_sysconf.ecname, esys->ec_name, 32);
@@ -182,31 +164,7 @@ void __init prom_init_env(void)
if (loongson_sysconf.nr_sensors)
memcpy(loongson_sysconf.sensors, esys->sensors,
sizeof(struct sensor_device) * loongson_sysconf.nr_sensors);
-#endif
- if (cpu_clock_freq == 0) {
- processor_id = (¤t_cpu_data)->processor_id;
- switch (processor_id & PRID_REV_MASK) {
- case PRID_REV_LOONGSON2E:
- cpu_clock_freq = 533080000;
- break;
- case PRID_REV_LOONGSON2F:
- cpu_clock_freq = 797000000;
- break;
- case PRID_REV_LOONGSON3A_R1:
- case PRID_REV_LOONGSON3A_R2_0:
- case PRID_REV_LOONGSON3A_R2_1:
- case PRID_REV_LOONGSON3A_R3_0:
- case PRID_REV_LOONGSON3A_R3_1:
- cpu_clock_freq = 900000000;
- break;
- case PRID_REV_LOONGSON3B_R1:
- case PRID_REV_LOONGSON3B_R2:
- cpu_clock_freq = 1000000000;
- break;
- default:
- cpu_clock_freq = 100000000;
- break;
- }
- }
+ processor_id = (¤t_cpu_data)->processor_id;
+
pr_info("CpuClock = %u\n", cpu_clock_freq);
}
similarity index 100%
rename from arch/mips/loongson64/loongson-3/hpet.c
rename to arch/mips/loongson64/hpet.c
similarity index 77%
rename from arch/mips/loongson64/loongson-3/irq.c
rename to arch/mips/loongson64/irq.c
@@ -1,5 +1,5 @@
// SPDX-License-Identifier: GPL-2.0
-#include <loongson.h>
+#include <loongson64.h>
#include <irq.h>
#include <linux/interrupt.h>
#include <linux/init.h>
@@ -10,6 +10,19 @@
#include "smp.h"
+/* ICU Configuration Regs - r/w */
+
+#define LOONGSON_INTEDGE LOONGSON_REG(LOONGSON_REGBASE + 0x24)
+#define LOONGSON_INTSTEER LOONGSON_REG(LOONGSON_REGBASE + 0x28)
+#define LOONGSON_INTPOL LOONGSON_REG(LOONGSON_REGBASE + 0x2c)
+
+/* ICU Enable Regs - IntEn & IntISR are r/o. */
+
+#define LOONGSON_INTENSET LOONGSON_REG(LOONGSON_REGBASE + 0x30)
+#define LOONGSON_INTENCLR LOONGSON_REG(LOONGSON_REGBASE + 0x34)
+#define LOONGSON_INTEN LOONGSON_REG(LOONGSON_REGBASE + 0x38)
+#define LOONGSON_INTISR LOONGSON_REG(LOONGSON_REGBASE + 0x3c)
+
extern void loongson3_send_irq_by_ipi(int cpu, int irqs);
unsigned int irq_cpu[16] = {[0 ... 15] = -1};
@@ -78,13 +91,17 @@ static void ht_irqdispatch(void)
#define UNUSED_IPS (CAUSEF_IP5 | CAUSEF_IP4 | CAUSEF_IP1 | CAUSEF_IP0)
-void mach_irq_dispatch(unsigned int pending)
+asmlinkage void plat_irq_dispatch(void)
{
+ unsigned int pending;
+
+ pending = read_c0_cause() & read_c0_status() & ST0_IM;
+
if (pending & CAUSEF_IP7)
do_IRQ(LOONGSON_TIMER_IRQ);
#if defined(CONFIG_SMP)
if (pending & CAUSEF_IP6)
- loongson3_ipi_interrupt(NULL);
+ loongson3_ipi_interrupt();
#endif
if (pending & CAUSEF_IP3)
ht_irqdispatch();
@@ -127,10 +144,25 @@ void irq_router_init(void)
LOONGSON_INT_ROUTER_INTEN | (0xffff << 16) | 0x1 << 10;
}
-void __init mach_init_irq(void)
+void __init arch_init_irq(void)
{
struct irq_chip *chip;
+ /*
+ * Clear all of the interrupts while we change the able around a bit.
+ * int-handler is not on bootstrap
+ */
+ clear_c0_status(ST0_IM | ST0_BEV);
+
+ /* no steer */
+ LOONGSON_INTSTEER = 0;
+
+ /*
+ * Mask out all interrupt by writing "1" to all bit position in
+ * the interrupt reset reg.
+ */
+ LOONGSON_INTENCLR = ~0;
+
clear_c0_status(ST0_IM | ST0_BEV);
irq_router_init();
deleted file mode 100644
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-#
-# Makefile for Loongson-3 family machines
-#
-obj-y += irq.o cop2-ex.o platform.o acpi_init.o dma.o
-
-obj-$(CONFIG_SMP) += smp.o
-
-obj-$(CONFIG_NUMA) += numa.o
-
-obj-$(CONFIG_RS780_HPET) += hpet.o
similarity index 98%
rename from arch/mips/loongson64/loongson-3/numa.c
rename to arch/mips/loongson64/numa.c
@@ -98,6 +98,7 @@ static void __init init_topology_matrix(void)
static unsigned long nid_to_addroffset(unsigned int nid)
{
unsigned long result;
+
switch (nid) {
case 0:
default:
@@ -119,7 +120,7 @@ static unsigned long nid_to_addroffset(unsigned int nid)
static void __init szmem(unsigned int node)
{
u32 i, mem_type;
- static unsigned long num_physpages = 0;
+ static unsigned long num_physpages;
u64 node_id, node_psize, start_pfn, end_pfn, mem_start, mem_size;
/* Parse memory information and activate */
@@ -276,4 +277,3 @@ void __init prom_init_numa_memory(void)
enable_lpa();
prom_meminit();
}
-EXPORT_SYMBOL(prom_init_numa_memory);
new file mode 100644
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/pci.h>
+
+#include <pci.h>
+#include <loongson64.h>
+
+static struct resource loongson_pci_mem_resource = {
+ .name = "PCI Memory Space",
+ .flags = IORESOURCE_MEM,
+};
+
+static struct resource loongson_pci_io_resource = {
+ .name = "PCI IO Space",
+ .end = IO_SPACE_LIMIT,
+ .flags = IORESOURCE_IO,
+};
+
+static struct pci_controller loongson_pci_controller = {
+ .pci_ops = &loongson_pci_ops,
+ .io_resource = &loongson_pci_io_resource,
+ .mem_resource = &loongson_pci_mem_resource,
+ .mem_offset = 0x00000000UL,
+ .io_offset = 0x00000000UL,
+};
+
+extern int sbx00_acpi_init(void);
+
+static int __init pcibios_init(void)
+{
+ loongson_pci_controller.io_map_base = mips_io_port_base;
+ loongson_pci_mem_resource.start = loongson_sysconf.pci_mem_start_addr;
+ loongson_pci_mem_resource.end = loongson_sysconf.pci_mem_end_addr;
+
+ register_pci_controller(&loongson_pci_controller);
+
+ sbx00_acpi_init();
+
+ return 0;
+}
+
+arch_initcall(pcibios_init);
similarity index 100%
rename from arch/mips/loongson64/loongson-3/platform.c
rename to arch/mips/loongson64/platform.c
new file mode 100644
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Zhangjin Wu, wuzhangjin@gmail.com
+ */
+#include <linux/init.h>
+#include <linux/pm.h>
+
+#include <asm/idle.h>
+#include <asm/reboot.h>
+
+#include <loongson64.h>
+#include <boot_param.h>
+
+static void loongson_restart(char *command)
+{
+ void (*fw_restart)(void) = (void *)loongson_sysconf.restart_addr;
+
+ fw_restart();
+ while (1) {
+ if (cpu_wait)
+ cpu_wait();
+ }
+}
+
+static void loongson_poweroff(void)
+{
+ void (*fw_poweroff)(void) = (void *)loongson_sysconf.poweroff_addr;
+
+ fw_poweroff();
+ while (1) {
+ if (cpu_wait)
+ cpu_wait();
+ }
+}
+
+static void loongson_halt(void)
+{
+ pr_notice("\n\n** You can safely turn off the power now **\n\n");
+ while (1) {
+ if (cpu_wait)
+ cpu_wait();
+ }
+}
+
+static int __init mips_reboot_setup(void)
+{
+ _machine_restart = loongson_restart;
+ _machine_halt = loongson_halt;
+ pm_power_off = loongson_poweroff;
+
+ return 0;
+}
+
+arch_initcall(mips_reboot_setup);
new file mode 100644
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#include <asm/bootinfo.h>
+#include <linux/memblock.h>
+#include <asm/bootinfo.h>
+#include <asm/prom.h>
+#include <asm/traps.h>
+#include <asm/setup.h>
+#include <asm/smp-ops.h>
+#include <asm/cacheflush.h>
+
+#include <loongson64.h>
+
+static void wbflush_loongson(void)
+{
+ asm(".set\tpush\n\t"
+ ".set\tnoreorder\n\t"
+ ".set mips3\n\t"
+ "sync\n\t"
+ "nop\n\t"
+ ".set\tpop\n\t"
+ ".set mips0\n\t");
+}
+
+void (*__wbflush)(void) = wbflush_loongson;
+EXPORT_SYMBOL(__wbflush);
+
+const char *get_system_type(void)
+{
+ return mips_get_machine_name();
+}
+
+static void __init mips_nmi_setup(void)
+{
+ void *base;
+ extern char except_vec_nmi;
+
+ base = (void *)(CAC_BASE + 0x380);
+ memcpy(base, &except_vec_nmi, 0x80);
+ flush_icache_range((unsigned long)base, (unsigned long)base + 0x80);
+}
+
+void __init prom_init_cmdline(void)
+{
+ int prom_argc;
+ /* pmon passes arguments in 32bit pointers */
+ int *_prom_argv;
+ int i;
+ long l;
+
+ /* firmware arguments are initialized in head.S */
+ prom_argc = fw_arg0;
+ _prom_argv = (int *)fw_arg1;
+
+ /* arg[0] is "g", the rest is boot parameters */
+ arcs_cmdline[0] = '\0';
+ for (i = 1; i < prom_argc; i++) {
+ l = (long)_prom_argv[i];
+ if (strlen(arcs_cmdline) + strlen(((char *)l) + 1)
+ >= sizeof(arcs_cmdline))
+ break;
+ strcat(arcs_cmdline, ((char *)l));
+ strcat(arcs_cmdline, " ");
+ }
+}
+
+void __init prom_init(void)
+{
+ prom_init_cmdline();
+ setup_8250_early_printk_port(CKSEG1ADDR(LOONGSON_REG_BASE + 0x1e0), 0, 0);
+
+ prom_init_lefi();
+ prom_init_numa_memory();
+
+ register_smp_ops(&loongson3_smp_ops);
+ board_nmi_handler_setup = mips_nmi_setup;
+}
+
+void __init prom_free_prom_memory(void)
+{
+}
+
+void __init plat_mem_setup(void)
+{
+}
+
+void __init plat_time_init(void)
+{
+#ifdef CONFIG_RS780_HPET
+ setup_hpet_timer();
+#endif
+}
+
similarity index 99%
rename from arch/mips/loongson64/loongson-3/smp.c
rename to arch/mips/loongson64/smp.c
@@ -17,7 +17,7 @@
#include <asm/clock.h>
#include <asm/tlbflush.h>
#include <asm/cacheflush.h>
-#include <loongson.h>
+#include <loongson64.h>
#include <workarounds.h>
#include "smp.h"
@@ -252,7 +252,7 @@ void loongson3_send_irq_by_ipi(int cpu, int irqs)
loongson3_ipi_write32(irqs << IPI_IRQ_OFFSET, ipi_set0_regs[cpu_logical_map(cpu)]);
}
-void loongson3_ipi_interrupt(struct pt_regs *regs)
+void loongson3_ipi_interrupt()
{
int i, cpu = smp_processor_id();
unsigned int action, c0count, irqs;
similarity index 100%
rename from arch/mips/loongson64/loongson-3/smp.h
rename to arch/mips/loongson64/smp.h
@@ -13,7 +13,7 @@
#include <linux/oprofile.h>
#include <linux/interrupt.h>
-#include <loongson.h> /* LOONGSON2_PERFCNT_IRQ */
+#include <loongson2ef.h> /* LOONGSON2_PERFCNT_IRQ */
#include "op_impl.h"
#define LOONGSON2_CPU_TYPE "mips/loongson2"
@@ -13,7 +13,7 @@
#include <linux/interrupt.h>
#include <linux/uaccess.h>
#include <irq.h>
-#include <loongson.h>
+#include <loongson64.h>
#include "op_impl.h"
#define LOONGSON3_PERFCNT_OVERFLOW (1ULL << 63)
@@ -35,7 +35,7 @@ obj-$(CONFIG_LASAT) += pci-lasat.o
obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o
obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o
obj-$(CONFIG_LEMOTE_MACH2F) += fixup-lemote2f.o ops-loongson2.o
-obj-$(CONFIG_LOONGSON_MACH3X) += fixup-loongson3.o ops-loongson3.o
+obj-$(CONFIG_MACH_LOONGSON64) += fixup-loongson3.o ops-loongson3.o
obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o pci-malta.o
obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
@@ -10,7 +10,7 @@
#include <linux/init.h>
#include <linux/pci.h>
-#include <loongson.h>
+#include <loongson2ef.h>
/* South bridge slot number is set by the pci probe process */
static u8 sb_slot = 5;
@@ -10,7 +10,7 @@
#include <linux/init.h>
#include <linux/pci.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#include <cs5536/cs5536.h>
#include <cs5536/cs5536_pci.h>
@@ -13,7 +13,7 @@
#include <linux/kernel.h>
#include <linux/export.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#ifdef CONFIG_CS5536
#include <cs5536/cs5536_pci.h>
@@ -5,7 +5,7 @@
#include <asm/mips-boards/bonito64.h>
-#include <loongson.h>
+#include <loongson64.h>
#define PCI_ACCESS_READ 0
#define PCI_ACCESS_WRITE 1
@@ -23,7 +23,7 @@
#include <asm/clock.h>
#include <asm/idle.h>
-#include <asm/mach-loongson64/loongson.h>
+#include <asm/mach-loongson2ef/loongson2ef.h>
static uint nowait;
@@ -17,7 +17,7 @@
#include <linux/platform_device.h>
#include <linux/bitops.h>
#include <asm/types.h>
-#include <loongson.h>
+#include <loongson2ef.h>
#define STLS2F_N_GPIO 4
#define STLS3A_N_GPIO 16
@@ -6,7 +6,7 @@
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
-#include <loongson.h>
+#include <loongson64.h>
#include <boot_param.h>
#include <loongson_hwmon.h>
As later model of GSx64 family processors including 2-series-soc have similar design with initial loongson3a while loongson2e/f seems less identical, we separate loongson2e/f support code out of mach-loongson64 to make our life easier. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> --- arch/mips/Kbuild.platforms | 1 + arch/mips/Kconfig | 51 +++++-- arch/mips/include/asm/bootinfo.h | 1 - .../mach-loongson2ef/cpu-feature-overrides.h | 45 +++++++ .../cs5536/cs5536.h | 0 .../cs5536/cs5536_mfgpt.h | 0 .../cs5536/cs5536_pci.h | 0 .../cs5536/cs5536_vsm.h | 0 .../loongson2ef.h} | 29 +--- .../machine.h | 6 - .../mc146818rtc.h | 5 +- .../mem.h | 6 +- arch/mips/include/asm/mach-loongson2ef/pci.h | 43 ++++++ .../include/asm/mach-loongson2ef/spaces.h | 10 ++ .../mach-loongson64/cpu-feature-overrides.h | 3 - arch/mips/include/asm/mach-loongson64/irq.h | 7 +- .../asm/mach-loongson64/kernel-entry-init.h | 74 ---------- .../include/asm/mach-loongson64/loongson64.h | 48 +++++++ .../mips/include/asm/mach-loongson64/mmzone.h | 16 --- arch/mips/include/asm/mach-loongson64/pci.h | 41 +----- .../include/asm/mach-loongson64/workarounds.h | 4 +- arch/mips/loongson2ef/Kconfig | 93 +++++++++++++ arch/mips/loongson2ef/Makefile | 18 +++ arch/mips/loongson2ef/Platform | 32 +++++ .../common/Makefile | 0 .../common/bonito-irq.c | 2 +- .../common/cmdline.c | 2 +- .../common/cs5536/Makefile | 0 .../common/cs5536/cs5536_acc.c | 0 .../common/cs5536/cs5536_ehci.c | 0 .../common/cs5536/cs5536_ide.c | 0 .../common/cs5536/cs5536_isa.c | 0 .../common/cs5536/cs5536_mfgpt.c | 0 .../common/cs5536/cs5536_ohci.c | 0 .../common/cs5536/cs5536_pci.c | 0 .../common/early_printk.c | 2 +- arch/mips/loongson2ef/common/env.c | 71 ++++++++++ .../{loongson64 => loongson2ef}/common/init.c | 7 +- .../{loongson64 => loongson2ef}/common/irq.c | 2 +- .../common/machtype.c | 3 +- .../{loongson64 => loongson2ef}/common/mem.c | 40 +----- .../{loongson64 => loongson2ef}/common/pci.c | 11 +- .../common/platform.c | 0 .../{loongson64 => loongson2ef}/common/pm.c | 2 +- .../common/reset.c | 23 +--- .../{loongson64 => loongson2ef}/common/rtc.c | 0 .../common/serial.c | 37 +---- .../common/setup.c | 2 +- .../{loongson64 => loongson2ef}/common/time.c | 2 +- .../common/uart_base.c | 10 +- .../fuloong-2e/Makefile | 0 .../fuloong-2e/dma.c | 0 .../fuloong-2e/irq.c | 2 +- .../fuloong-2e/reset.c | 2 +- .../lemote-2f/Makefile | 0 .../lemote-2f/clock.c | 2 +- .../lemote-2f/dma.c | 0 .../lemote-2f/ec_kb3310b.c | 0 .../lemote-2f/ec_kb3310b.h | 0 .../lemote-2f/irq.c | 2 +- .../lemote-2f/machtype.c | 2 +- .../lemote-2f/pm.c | 2 +- .../lemote-2f/reset.c | 2 +- arch/mips/loongson64/Kconfig | 126 +----------------- arch/mips/loongson64/Makefile | 23 +--- arch/mips/loongson64/Platform | 26 +--- .../loongson64/{loongson-3 => }/acpi_init.c | 3 +- .../loongson64/{loongson-3 => }/cop2-ex.c | 5 +- arch/mips/loongson64/{loongson-3 => }/dma.c | 6 +- arch/mips/loongson64/{common => }/env.c | 72 +++------- arch/mips/loongson64/{loongson-3 => }/hpet.c | 0 arch/mips/loongson64/{loongson-3 => }/irq.c | 40 +++++- arch/mips/loongson64/loongson-3/Makefile | 11 -- arch/mips/loongson64/{loongson-3 => }/numa.c | 4 +- arch/mips/loongson64/pci.c | 45 +++++++ .../loongson64/{loongson-3 => }/platform.c | 0 arch/mips/loongson64/reset.c | 58 ++++++++ arch/mips/loongson64/setup.c | 92 +++++++++++++ arch/mips/loongson64/{loongson-3 => }/smp.c | 4 +- arch/mips/loongson64/{loongson-3 => }/smp.h | 0 arch/mips/oprofile/op_model_loongson2.c | 2 +- arch/mips/oprofile/op_model_loongson3.c | 2 +- arch/mips/pci/Makefile | 2 +- arch/mips/pci/fixup-fuloong2e.c | 2 +- arch/mips/pci/fixup-lemote2f.c | 2 +- arch/mips/pci/ops-loongson2.c | 2 +- arch/mips/pci/ops-loongson3.c | 2 +- drivers/cpufreq/loongson2_cpufreq.c | 2 +- drivers/gpio/gpio-loongson.c | 2 +- drivers/platform/mips/cpu_hwmon.c | 2 +- 90 files changed, 720 insertions(+), 578 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson2ef/cpu-feature-overrides.h rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/cs5536/cs5536.h (100%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/cs5536/cs5536_mfgpt.h (100%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/cs5536/cs5536_pci.h (100%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/cs5536/cs5536_vsm.h (100%) rename arch/mips/include/asm/{mach-loongson64/loongson.h => mach-loongson2ef/loongson2ef.h} (91%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/machine.h (80%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/mc146818rtc.h (80%) rename arch/mips/include/asm/{mach-loongson64 => mach-loongson2ef}/mem.h (86%) create mode 100644 arch/mips/include/asm/mach-loongson2ef/pci.h create mode 100644 arch/mips/include/asm/mach-loongson2ef/spaces.h delete mode 100644 arch/mips/include/asm/mach-loongson64/kernel-entry-init.h create mode 100644 arch/mips/include/asm/mach-loongson64/loongson64.h create mode 100644 arch/mips/loongson2ef/Kconfig create mode 100644 arch/mips/loongson2ef/Makefile create mode 100644 arch/mips/loongson2ef/Platform rename arch/mips/{loongson64 => loongson2ef}/common/Makefile (100%) rename arch/mips/{loongson64 => loongson2ef}/common/bonito-irq.c (97%) rename arch/mips/{loongson64 => loongson2ef}/common/cmdline.c (97%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/Makefile (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_acc.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_ehci.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_ide.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_isa.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_mfgpt.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_ohci.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/cs5536/cs5536_pci.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/early_printk.c (97%) create mode 100644 arch/mips/loongson2ef/common/env.c rename arch/mips/{loongson64 => loongson2ef}/common/init.c (90%) rename arch/mips/{loongson64 => loongson2ef}/common/irq.c (98%) rename arch/mips/{loongson64 => loongson2ef}/common/machtype.c (94%) rename arch/mips/{loongson64 => loongson2ef}/common/mem.c (72%) rename arch/mips/{loongson64 => loongson2ef}/common/pci.c (89%) rename arch/mips/{loongson64 => loongson2ef}/common/platform.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/pm.c (99%) rename arch/mips/{loongson64 => loongson2ef}/common/reset.c (77%) rename arch/mips/{loongson64 => loongson2ef}/common/rtc.c (100%) rename arch/mips/{loongson64 => loongson2ef}/common/serial.c (63%) rename arch/mips/{loongson64 => loongson2ef}/common/setup.c (97%) rename arch/mips/{loongson64 => loongson2ef}/common/time.c (96%) rename arch/mips/{loongson64 => loongson2ef}/common/uart_base.c (77%) rename arch/mips/{loongson64 => loongson2ef}/fuloong-2e/Makefile (100%) rename arch/mips/{loongson64 => loongson2ef}/fuloong-2e/dma.c (100%) rename arch/mips/{loongson64 => loongson2ef}/fuloong-2e/irq.c (98%) rename arch/mips/{loongson64 => loongson2ef}/fuloong-2e/reset.c (93%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/Makefile (100%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/clock.c (98%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/dma.c (100%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/ec_kb3310b.c (100%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/ec_kb3310b.h (100%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/irq.c (99%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/machtype.c (98%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/pm.c (99%) rename arch/mips/{loongson64 => loongson2ef}/lemote-2f/reset.c (99%) rename arch/mips/loongson64/{loongson-3 => }/acpi_init.c (99%) rename arch/mips/loongson64/{loongson-3 => }/cop2-ex.c (88%) rename arch/mips/loongson64/{loongson-3 => }/dma.c (82%) rename arch/mips/loongson64/{common => }/env.c (79%) rename arch/mips/loongson64/{loongson-3 => }/hpet.c (100%) rename arch/mips/loongson64/{loongson-3 => }/irq.c (77%) delete mode 100644 arch/mips/loongson64/loongson-3/Makefile rename arch/mips/loongson64/{loongson-3 => }/numa.c (98%) create mode 100644 arch/mips/loongson64/pci.c rename arch/mips/loongson64/{loongson-3 => }/platform.c (100%) create mode 100644 arch/mips/loongson64/reset.c create mode 100644 arch/mips/loongson64/setup.c rename arch/mips/loongson64/{loongson-3 => }/smp.c (99%) rename arch/mips/loongson64/{loongson-3 => }/smp.h (100%)