| Message ID | 20211016132228.40254-5-paul@crapouillou.net (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | [v2,1/5] mtd: rawnand/davinci: Don't calculate ECC when reading page | expand |
On Sat, 2021-10-16 at 13:22:28 UTC, Paul Cercueil wrote: > The ECC engine on the JZ4740 SoC requires the ECC data to be read before > the page; using the default page reading function does not work. Indeed, > the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag > that existed back then. > > Use the newly created nand_read_page_hwecc_oob_first() to address this > issue. > > This issue was not found when the new ingenic-nand driver was developed, > most likely because the Device Tree used had the nand-ecc-mode set to > "hw_oob_first", which seems to not be supported anymore. > > Cc: <stable@vger.kernel.org> # v5.2 > Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") > Signed-off-by: Paul Cercueil <paul@crapouillou.net> Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next, thanks. Miquel
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c index 0e9d426fe4f2..b18861bdcdc8 100644 --- a/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c +++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c @@ -32,6 +32,7 @@ struct jz_soc_info { unsigned long addr_offset; unsigned long cmd_offset; const struct mtd_ooblayout_ops *oob_layout; + bool oob_first; }; struct ingenic_nand_cs { @@ -240,6 +241,9 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip) if (chip->bbt_options & NAND_BBT_USE_FLASH) chip->bbt_options |= NAND_BBT_NO_OOB; + if (nfc->soc_info->oob_first) + chip->ecc.read_page = nand_read_page_hwecc_oob_first; + /* For legacy reasons we use a different layout on the qi,lb60 board. */ if (of_machine_is_compatible("qi,lb60")) mtd_set_ooblayout(mtd, &qi_lb60_ooblayout_ops); @@ -534,6 +538,7 @@ static const struct jz_soc_info jz4740_soc_info = { .data_offset = 0x00000000, .cmd_offset = 0x00008000, .addr_offset = 0x00010000, + .oob_first = true, }; static const struct jz_soc_info jz4725b_soc_info = {
The ECC engine on the JZ4740 SoC requires the ECC data to be read before the page; using the default page reading function does not work. Indeed, the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag that existed back then. Use the newly created nand_read_page_hwecc_oob_first() to address this issue. This issue was not found when the new ingenic-nand driver was developed, most likely because the Device Tree used had the nand-ecc-mode set to "hw_oob_first", which seems to not be supported anymore. Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> --- drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c | 5 +++++ 1 file changed, 5 insertions(+)