@@ -218,18 +218,48 @@ static int jz4740_i2s_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
return 0;
}
+static int jz4740_i2s_get_i2sdiv(unsigned long mclk, unsigned long rate,
+ unsigned long i2sdiv_max)
+{
+ unsigned long div, rate1, rate2, err1, err2;
+
+ div = mclk / (64 * rate);
+ if (div == 0)
+ div = 1;
+
+ rate1 = mclk / (64 * div);
+ rate2 = mclk / (64 * (div + 1));
+
+ err1 = abs(rate1 - rate);
+ err2 = abs(rate2 - rate);
+
+ /*
+ * Choose the divider that produces the smallest error in the
+ * output rate and reject dividers with a 5% or higher error.
+ * In the event that both dividers are outside the acceptable
+ * error margin, reject the rate to prevent distorted audio.
+ * (The number 5% is arbitrary.)
+ */
+ if (div <= i2sdiv_max && err1 <= err2 && err1 < rate/20)
+ return div;
+ if (div < i2sdiv_max && err2 < rate/20)
+ return div + 1;
+
+ return -EINVAL;
+}
+
static int jz4740_i2s_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
{
struct jz4740_i2s *i2s = snd_soc_dai_get_drvdata(dai);
struct regmap_field *div_field;
+ unsigned long i2sdiv_max;
unsigned int sample_size;
- uint32_t ctrl;
- int div;
+ uint32_t ctrl, conf;
+ int div = 1;
regmap_read(i2s->regmap, JZ_REG_AIC_CTRL, &ctrl);
-
- div = clk_get_rate(i2s->clk_i2s) / (64 * params_rate(params));
+ regmap_read(i2s->regmap, JZ_REG_AIC_CONF, &conf);
switch (params_format(params)) {
case SNDRV_PCM_FORMAT_S8:
@@ -258,11 +288,27 @@ static int jz4740_i2s_hw_params(struct snd_pcm_substream *substream,
ctrl &= ~JZ_AIC_CTRL_MONO_TO_STEREO;
div_field = i2s->field_i2sdiv_playback;
+ i2sdiv_max = GENMASK(i2s->soc_info->field_i2sdiv_playback.msb,
+ i2s->soc_info->field_i2sdiv_playback.lsb);
} else {
ctrl &= ~JZ_AIC_CTRL_INPUT_SAMPLE_SIZE;
ctrl |= FIELD_PREP(JZ_AIC_CTRL_INPUT_SAMPLE_SIZE, sample_size);
div_field = i2s->field_i2sdiv_capture;
+ i2sdiv_max = GENMASK(i2s->soc_info->field_i2sdiv_capture.msb,
+ i2s->soc_info->field_i2sdiv_capture.lsb);
+ }
+
+ /*
+ * Only calculate I2SDIV if we're supplying the bit or frame clock.
+ * If the codec is supplying both clocks then the divider output is
+ * unused, and we don't want it to limit the allowed sample rates.
+ */
+ if (conf & (JZ_AIC_CONF_BIT_CLK_MASTER | JZ_AIC_CONF_SYNC_CLK_MASTER)) {
+ div = jz4740_i2s_get_i2sdiv(clk_get_rate(i2s->clk_i2s),
+ params_rate(params), i2sdiv_max);
+ if (div < 0)
+ return div;
}
regmap_write(i2s->regmap, JZ_REG_AIC_CTRL, ctrl);
When the CPU supplies bit/frame clocks, the system clock (clk_i2s) is divided to produce the bit clock. This is a simple 1/N divider with a fairly limited range, so for a given system clock frequency only a few sample rates can be produced. Usually a wider range of sample rates is supported by varying the system clock frequency. The old calculation method was not very robust and could easily produce the wrong clock rate, especially with non-standard rates. For example, if the system clock is 1.99x the target bit clock rate, the divider would be calculated as 1 instead of the more accurate 2. Instead, use a more accurate method that considers two adjacent divider settings and selects the one that produces the least error versus the requested rate. If the error is 5% or higher then the rate setting is rejected to prevent garbled audio. Skip divider calculation when the codec is supplying both the bit and frame clock; in that case, the divider outputs are unused and we don't want to constrain the sample rate. Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> --- sound/soc/jz4740/jz4740-i2s.c | 54 ++++++++++++++++++++++++++++++++--- 1 file changed, 50 insertions(+), 4 deletions(-)