| Message ID | 20231108-fix-mips-nand-v1-5-5fc5586d04de@linaro.org (mailing list archive) |
|---|---|
| State | Handled Elsewhere |
| Headers | show |
| Series | Fix polarity and bindings for GPIO-based NAND drivers | expand |
Hi Linus, linus.walleij@linaro.org wrote on Wed, 08 Nov 2023 15:33:53 +0100: > The standard property for describing the band width of a NAND > memory is "nand-bus-width" not "bank-width". The new bindings > support both so make Linux check both in priority order. > > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > drivers/mtd/nand/raw/gpio.c | 10 +++++++++- > 1 file changed, 9 insertions(+), 1 deletion(-) > > diff --git a/drivers/mtd/nand/raw/gpio.c b/drivers/mtd/nand/raw/gpio.c > index 5553101c709c..d5bd245b0c0d 100644 > --- a/drivers/mtd/nand/raw/gpio.c > +++ b/drivers/mtd/nand/raw/gpio.c > @@ -183,7 +183,15 @@ static int gpio_nand_get_config(struct device *dev, > { > u32 val; > > - if (!device_property_read_u32(dev, "bank-width", &val)) { > + /* The preferred binding takes precedence */ > + if (!device_property_read_u32(dev, "nand-bus-width", &val)) { > + if (val == 16) { > + chip->options |= NAND_BUSWIDTH_16; > + } else if (val != 8) { > + dev_err(dev, "invalid nand-bus-width %u\n", val); > + return -EINVAL; > + } > + } else if (!device_property_read_u32(dev, "bank-width", &val)) { > if (val == 2) { > chip->options |= NAND_BUSWIDTH_16; > } else if (val != 1) { > I'm not sure this is actually needed. I believe of_get_nand_bus_width is already called (nand_scan_ident -> rawnand_dt_init) and will set the NAND_BUSWIDTH_16 flag automatically. So the above 'if' is already a fallback. Maybe you can add a comment if you want to make this more explicit that the real property is nand-bus-width and the property parsed in the driver is for backward compatibility only? Thanks, Miquèl
diff --git a/drivers/mtd/nand/raw/gpio.c b/drivers/mtd/nand/raw/gpio.c index 5553101c709c..d5bd245b0c0d 100644 --- a/drivers/mtd/nand/raw/gpio.c +++ b/drivers/mtd/nand/raw/gpio.c @@ -183,7 +183,15 @@ static int gpio_nand_get_config(struct device *dev, { u32 val; - if (!device_property_read_u32(dev, "bank-width", &val)) { + /* The preferred binding takes precedence */ + if (!device_property_read_u32(dev, "nand-bus-width", &val)) { + if (val == 16) { + chip->options |= NAND_BUSWIDTH_16; + } else if (val != 8) { + dev_err(dev, "invalid nand-bus-width %u\n", val); + return -EINVAL; + } + } else if (!device_property_read_u32(dev, "bank-width", &val)) { if (val == 2) { chip->options |= NAND_BUSWIDTH_16; } else if (val != 1) {
The standard property for describing the band width of a NAND memory is "nand-bus-width" not "bank-width". The new bindings support both so make Linux check both in priority order. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/mtd/nand/raw/gpio.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)