@@ -11,6 +11,7 @@ platform-$(CONFIG_CAVIUM_OCTEON_SOC) += cavium-octeon/
platform-$(CONFIG_EYEQ) += mobileye/
platform-$(CONFIG_MIPS_COBALT) += cobalt/
platform-$(CONFIG_MACH_DECSTATION) += dec/
+platform-$(CONFIG_ECONET) += econet/
platform-$(CONFIG_MIPS_GENERIC) += generic/
platform-$(CONFIG_MACH_JAZZ) += jazz/
platform-$(CONFIG_LANTIQ) += lantiq/
@@ -390,6 +390,30 @@ config MACH_DECSTATION
otherwise choose R3000.
+config ECONET
+ bool "EcoNet MIPS family"
+ select BOOT_RAW
+ select CPU_BIG_ENDIAN
+ select DEBUG_ZBOOT
+ select EARLY_PRINTK_8250
+ select ECONET_EN751221_TIMER
+ select SERIAL_OF_PLATFORM
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select SYS_HAS_CPU_MIPS32_R1
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_HAS_EARLY_PRINTK
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_MIPS16
+ select SYS_SUPPORTS_ZBOOT_UART16550
+ select USE_GENERIC_EARLY_PRINTK_8250
+ select USE_OF
+ help
+ EcoNet EN75xx MIPS devices are big endian MIPS machines used
+ in XPON (fiber) and DSL applications. They have SPI, PCI, USB,
+ GPIO, and Ethernet, with optional XPON, DSL, and VoIP DSP cores.
+ Don't confuse these with the Airoha ARM devices sometimes referred
+ to as "EcoNet", this family is for MIPS based devices only.
+
config MACH_JAZZ
bool "Jazz family of machines"
select ARC_MEMORY
@@ -1019,6 +1043,7 @@ source "arch/mips/ath79/Kconfig"
source "arch/mips/bcm47xx/Kconfig"
source "arch/mips/bcm63xx/Kconfig"
source "arch/mips/bmips/Kconfig"
+source "arch/mips/econet/Kconfig"
source "arch/mips/generic/Kconfig"
source "arch/mips/ingenic/Kconfig"
source "arch/mips/jazz/Kconfig"
@@ -20,6 +20,11 @@
#define PORT(offset) (CKSEG1ADDR(INGENIC_UART_BASE_ADDR) + (4 * offset))
#endif
+#ifdef CONFIG_ECONET
+#define EN75_UART_BASE 0x1fbf0003
+#define PORT(offset) (CKSEG1ADDR(EN75_UART_BASE) + (4 * (offset)))
+#endif
+
#ifndef IOTYPE
#define IOTYPE char
#endif
new file mode 100644
@@ -0,0 +1,37 @@
+# SPDX-License-Identifier: GPL-2.0
+if ECONET
+
+choice
+ prompt "EcoNet SoC selection"
+ default SOC_ECONET_EN751221
+ help
+ Select EcoNet MIPS SoC type. Individual SoCs within a family are
+ very similar, so is it enough to select the right family, and
+ then customize to the specific SoC using the device tree only.
+
+ config SOC_ECONET_EN751221
+ bool "EN751221 family"
+ select COMMON_CLK
+ select ECONET_EN751221_INTC
+ select IRQ_MIPS_CPU
+ select SMP
+ select SMP_UP
+ select SYS_SUPPORTS_SMP
+ help
+ The EN751221 family includes EN7512, RN7513, EN7521, EN7526.
+ They are based on single core MIPS 34Kc processors. To boot
+ this kernel, you will need a device tree such as
+ MIPS_RAW_APPENDED_DTB=y, and a root filesystem.
+endchoice
+
+choice
+ prompt "Devicetree selection"
+ default DTB_ECONET_NONE
+ help
+ Select the devicetree.
+
+ config DTB_ECONET_NONE
+ bool "None"
+endchoice
+
+endif
new file mode 100644
@@ -0,0 +1,2 @@
+
+obj-y := init.o
new file mode 100644
@@ -0,0 +1,5 @@
+# To address a 7.2MB kernel size limit in the EcoNet SDK bootloader,
+# we put the load address well above where the bootloader loads and then use
+# zboot. So please set CONFIG_ZBOOT_LOAD_ADDRESS to the address where your
+# bootloader actually places the kernel.
+load-$(CONFIG_ECONET) += 0xffffffff81000000
new file mode 100644
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * EcoNet setup code
+ *
+ * Copyright (C) 2025 Caleb James DeLisle <cjd@cjdns.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/of_clk.h>
+#include <linux/irqchip.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+#include <asm/smp-ops.h>
+#include <asm/reboot.h>
+
+#define CR_AHB_RSTCR ((void __iomem *)CKSEG1ADDR(0x1fb00040))
+#define RESET BIT(31)
+
+#define UART_BASE CKSEG1ADDR(0x1fbf0003)
+#define UART_REG_SHIFT 2
+
+static void hw_reset(char *command)
+{
+ iowrite32(RESET, CR_AHB_RSTCR);
+}
+
+/* 1. Bring up early printk. */
+void __init prom_init(void)
+{
+ setup_8250_early_printk_port(UART_BASE, UART_REG_SHIFT, 0);
+ _machine_restart = hw_reset;
+}
+
+/* 2. Parse the DT and find memory */
+void __init plat_mem_setup(void)
+{
+ void *dtb;
+
+ set_io_port_base(KSEG1);
+
+ dtb = get_fdt();
+ if (!dtb)
+ panic("no dtb found");
+
+ __dt_setup_arch(dtb);
+
+ early_init_dt_scan_memory();
+}
+
+/* 3. Overload __weak device_tree_init(), add SMP_UP ops */
+void __init device_tree_init(void)
+{
+ unflatten_and_copy_device_tree();
+
+ register_up_smp_ops();
+}
+
+const char *get_system_type(void)
+{
+ return "EcoNet-EN75xx";
+}
+
+/* 4. Initialize the IRQ subsystem */
+void __init arch_init_irq(void)
+{
+ irqchip_init();
+}
+
+/* 5. Timers */
+void __init plat_time_init(void)
+{
+ of_clk_init(NULL);
+ timer_probe();
+}
Add platform support for EcoNet MIPS SoCs. Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr> --- arch/mips/Kbuild.platforms | 1 + arch/mips/Kconfig | 25 +++++++++ arch/mips/boot/compressed/uart-16550.c | 5 ++ arch/mips/econet/Kconfig | 37 ++++++++++++ arch/mips/econet/Makefile | 2 + arch/mips/econet/Platform | 5 ++ arch/mips/econet/init.c | 78 ++++++++++++++++++++++++++ 7 files changed, 153 insertions(+) create mode 100644 arch/mips/econet/Kconfig create mode 100644 arch/mips/econet/Makefile create mode 100644 arch/mips/econet/Platform create mode 100644 arch/mips/econet/init.c