@@ -347,6 +347,60 @@
.endm
/*
+ * Switch back from the kernel stack to the entry stack.
+ *
+ * The %esp register must point to pt_regs on the task stack. It will
+ * first calculate the size of the stack-frame to copy, depending on
+ * whether we return to VM86 mode or not. With that it uses 'rep movsl'
+ * to copy the contents of the stack over to the entry stack.
+ *
+ * We must be very careful here, as we can't trust the contents of the
+ * task-stack once we switched to the entry-stack. When an NMI happens
+ * while on the entry-stack, the NMI handler will switch back to the top
+ * of the task stack, overwriting our stack-frame we are about to copy.
+ * Therefore we switch the stack only after everything is copied over.
+ */
+.macro SWITCH_TO_ENTRY_STACK
+
+ ALTERNATIVE "", "jmp .Lend_\@", X86_FEATURE_XENPV
+
+ /* Bytes to copy */
+ movl $PTREGS_SIZE, %ecx
+
+#ifdef CONFIG_VM86
+ testl $(X86_EFLAGS_VM), PT_EFLAGS(%esp)
+ jz .Lcopy_pt_regs_\@
+
+ /* Additional 4 registers to copy when returning to VM86 mode */
+ addl $(4 * 4), %ecx
+
+.Lcopy_pt_regs_\@:
+#endif
+
+ /* Initialize source and destination for movsl */
+ movl PER_CPU_VAR(cpu_tss_rw + TSS_sp0), %edi
+ subl %ecx, %edi
+ movl %esp, %esi
+
+ /* Save future stack pointer in %ebx */
+ movl %edi, %ebx
+
+ /* Copy over the stack-frame */
+ shrl $2, %ecx
+ cld
+ rep movsl
+
+ /*
+ * Switch to entry-stack - needs to happen after everything is
+ * copied because the NMI handler will overwrite the task-stack
+ * when on entry-stack
+ */
+ movl %ebx, %esp
+
+.Lend_\@:
+.endm
+
+/*
* %eax: prev task
* %edx: next task
*/
@@ -586,25 +640,45 @@ ENTRY(entry_SYSENTER_32)
/* Opportunistic SYSEXIT */
TRACE_IRQS_ON /* User mode traces as IRQs on. */
+
+ /*
+ * Setup entry stack - we keep the pointer in %eax and do the
+ * switch after almost all user-state is restored.
+ */
+
+ /* Load entry stack pointer and allocate frame for eflags/eax */
+ movl PER_CPU_VAR(cpu_tss_rw + TSS_sp0), %eax
+ subl $(2*4), %eax
+
+ /* Copy eflags and eax to entry stack */
+ movl PT_EFLAGS(%esp), %edi
+ movl PT_EAX(%esp), %esi
+ movl %edi, (%eax)
+ movl %esi, 4(%eax)
+
+ /* Restore user registers and segments */
movl PT_EIP(%esp), %edx /* pt_regs->ip */
movl PT_OLDESP(%esp), %ecx /* pt_regs->sp */
1: mov PT_FS(%esp), %fs
PTGS_TO_GS
+
popl %ebx /* pt_regs->bx */
addl $2*4, %esp /* skip pt_regs->cx and pt_regs->dx */
popl %esi /* pt_regs->si */
popl %edi /* pt_regs->di */
popl %ebp /* pt_regs->bp */
- popl %eax /* pt_regs->ax */
+
+ /* Switch to entry stack */
+ movl %eax, %esp
/*
* Restore all flags except IF. (We restore IF separately because
* STI gives a one-instruction window in which we won't be interrupted,
* whereas POPF does not.)
*/
- addl $PT_EFLAGS-PT_DS, %esp /* point esp at pt_regs->flags */
btrl $X86_EFLAGS_IF_BIT, (%esp)
popfl
+ popl %eax
/*
* Return back to the vDSO, which will pop ecx and edx.
@@ -673,6 +747,7 @@ ENTRY(entry_INT80_32)
restore_all:
TRACE_IRQS_IRET
+ SWITCH_TO_ENTRY_STACK
.Lrestore_all_notrace:
CHECK_AND_APPLY_ESPFIX
.Lrestore_nocheck: