diff mbox

[v2,1/2] ARM: OMAP4: MMC: increase delay for pbias

Message ID 1306926923-3398-2-git-send-email-balajitk@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

Balaji T K June 1, 2011, 11:15 a.m. UTC 
4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.

Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"

Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>
---
v2:
replace usleep by usleep_range

 arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
 1 files changed, 10 insertions(+), 3 deletions(-)

Comments

Tony Lindgren June 1, 2011, 11:49 a.m. UTC | #1 
* Balaji T K <balajitk@ti.com> [110601 04:13]:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
> 
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"

Thanks for updating this, applying to devel-fixes.

Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index b2f30be..24f25c7 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -145,6 +145,7 @@  static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 				 int power_on, int vdd)
 {
 	u32 reg;
+	unsigned long timeout;
 
 	if (power_on) {
 		reg = omap4_ctrl_pad_readl(control_pbias_offset);
@@ -157,9 +158,15 @@  static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 			OMAP4_MMC1_PWRDNZ_MASK |
 			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
-		/* 4 microsec delay for comparator to generate an error*/
-		udelay(4);
-		reg = omap4_ctrl_pad_readl(control_pbias_offset);
+
+		timeout = jiffies + msecs_to_jiffies(5);
+		do {
+			reg = omap4_ctrl_pad_readl(control_pbias_offset);
+			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
+				break;
+			usleep_range(100, 200);
+		} while (!time_after(jiffies, timeout));
+
 		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
 			pr_err("Pbias Voltage is not same as LDO\n");
 			/* Caution : On VMODE_ERROR Power Down MMC IO */