| Message ID | 1386263677-7733-2-git-send-email-dinguyen@altera.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thursday 05 December 2013, dinguyen@altera.com wrote: > From: Dinh Nguyen <dinguyen@altera.com> > > Re-use the "rockchip,rk2928-dw-mshc" binding that will support SD/MMC on > Altera's SOCFPGA platform. > > Signed-off-by: Dinh Nguyen <dinguyen@altera.com> > --- > v3: Re-use "rockchip,rk2928-dw-mshc" binding > v3: none > v2: none > --- > arch/arm/boot/dts/socfpga.dtsi | 11 +++++++++++ > arch/arm/boot/dts/socfpga_arria5.dtsi | 12 ++++++++++++ > arch/arm/boot/dts/socfpga_cyclone5.dtsi | 12 ++++++++++++ > arch/arm/boot/dts/socfpga_vt.dts | 12 ++++++++++++ > 4 files changed, 47 insertions(+) > > diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi > index f936476..3d9f01b 100644 > --- a/arch/arm/boot/dts/socfpga.dtsi > +++ b/arch/arm/boot/dts/socfpga.dtsi > @@ -469,6 +469,17 @@ > cache-level = <2>; > }; > > + mmc: dwmmc0@ff704000 { > + compatible = "rockchip,rk2928-dw-mshc"; > + reg = <0xff704000 0x1000>; > + interrupts = <0 139 4>; > + fifo-depth = <0x400>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&l4_mp_clk>, <&sdmmc_clk>; > + clock-names = "biu", "ciu"; > + }; I think it's great that you can reuse the existing driver, but I'd recommend using a generic compatible string here in addition to one that identifies your specific implementation. You can list "rockchip,rk2928-dw-mshc" as well, but that is probably not necessary. What I'd expect to see here is either compatible = "altr,socfpga-dw-mshc", "rockchip,rk2928-dw-mshc", "snps,dw-mshc"; or compatible = "altr,socfpga-dw-mshc", "rockchip,rk2928-dw-mshc", "snps,dw-mshc"; It's probably not too late to generalize the SDMMC_CMD_USE_HOLD_REG handling, which is currently the only difference between the generic "snps,dw-mshc" and the newer "rockchip,rk2928-dw-mshc" variant. It's quite likely that all implementations should actually set SDMMC_CMD_USE_HOLD_REG (if both rockchips and altera set it) and you don't need to have any distinction in the dw_mmc-pltfm.c driver at all. If it's actually needed on some but not others, you could add a binary DT property to tell the driver about it rather than keying it off of the compatible string. If it's needed only on older (or only on newer) versions of the dw-mshc design, it could be encoded as a version in the string, such as "snps,dw-mshc-1.234". Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, 2013-12-05 at 22:08 +0100, Arnd Bergmann wrote: > On Thursday 05 December 2013, dinguyen@altera.com wrote: > > From: Dinh Nguyen <dinguyen@altera.com> > > > > Re-use the "rockchip,rk2928-dw-mshc" binding that will support SD/MMC on > > Altera's SOCFPGA platform. > > > > Signed-off-by: Dinh Nguyen <dinguyen@altera.com> > > --- > > v3: Re-use "rockchip,rk2928-dw-mshc" binding > > v3: none > > v2: none > > --- > > arch/arm/boot/dts/socfpga.dtsi | 11 +++++++++++ > > arch/arm/boot/dts/socfpga_arria5.dtsi | 12 ++++++++++++ > > arch/arm/boot/dts/socfpga_cyclone5.dtsi | 12 ++++++++++++ > > arch/arm/boot/dts/socfpga_vt.dts | 12 ++++++++++++ > > 4 files changed, 47 insertions(+) > > > > diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi > > index f936476..3d9f01b 100644 > > --- a/arch/arm/boot/dts/socfpga.dtsi > > +++ b/arch/arm/boot/dts/socfpga.dtsi > > @@ -469,6 +469,17 @@ > > cache-level = <2>; > > }; > > > > + mmc: dwmmc0@ff704000 { > > + compatible = "rockchip,rk2928-dw-mshc"; > > + reg = <0xff704000 0x1000>; > > + interrupts = <0 139 4>; > > + fifo-depth = <0x400>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + clocks = <&l4_mp_clk>, <&sdmmc_clk>; > > + clock-names = "biu", "ciu"; > > + }; > > > I think it's great that you can reuse the existing driver, but I'd recommend > using a generic compatible string here in addition to one that identifies > your specific implementation. You can list "rockchip,rk2928-dw-mshc" as > well, but that is probably not necessary. > > What I'd expect to see here is either > > compatible = "altr,socfpga-dw-mshc", "rockchip,rk2928-dw-mshc", "snps,dw-mshc"; > > or > > compatible = "altr,socfpga-dw-mshc", "rockchip,rk2928-dw-mshc", "snps,dw-mshc"; > > > It's probably not too late to generalize the SDMMC_CMD_USE_HOLD_REG > handling, which is currently the only difference between the generic > "snps,dw-mshc" and the newer "rockchip,rk2928-dw-mshc" variant. Ok, I will try to generalize the driver. > > It's quite likely that all implementations should actually set > SDMMC_CMD_USE_HOLD_REG (if both rockchips and altera set it) and you > don't need to have any distinction in the dw_mmc-pltfm.c driver at all. > > If it's actually needed on some but not others, you could add a binary > DT property to tell the driver about it rather than keying it off of > the compatible string. If it's needed only on older (or only on newer) > versions of the dw-mshc design, it could be encoded as a version in the > string, such as "snps,dw-mshc-1.234". Perhaps Seungwon and Chris might have an opinion on this: From the Synopsys databook for this IP, using the SDMMC_CMD_USE_HOLD_REG is not recommended for SDR104, SDR50 and DDR50 speed modes. For other speeds, SDR12, and SDR25, it would be necessary to use SDMMC_CMD_USE_HOLD_REG. I am referencing v2.50a of the Synopsys DesignWare Cores Mobile Storage Host Databook. So I think a binary DT property should suffice? Thanks, Dinh > > Arnd > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thursday 05 December 2013, Dinh Nguyen wrote: > Perhaps Seungwon and Chris might have an opinion on this: > > From the Synopsys databook for this IP, using the SDMMC_CMD_USE_HOLD_REG > is not recommended for SDR104, SDR50 and DDR50 speed modes. For other > speeds, SDR12, and SDR25, it would be necessary to use > SDMMC_CMD_USE_HOLD_REG. > > I am referencing v2.50a of the Synopsys DesignWare Cores Mobile Storage > Host Databook. > > So I think a binary DT property should suffice? Well, if it depends on the interface speed, it is something the driver should actually be able to figure out itself, since it knows the speed that is used. That way, you don't even need a property or per-platform compatible string. Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index f936476..3d9f01b 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -469,6 +469,17 @@ cache-level = <2>; }; + mmc: dwmmc0@ff704000 { + compatible = "rockchip,rk2928-dw-mshc"; + reg = <0xff704000 0x1000>; + interrupts = <0 139 4>; + fifo-depth = <0x400>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&l4_mp_clk>, <&sdmmc_clk>; + clock-names = "biu", "ciu"; + }; + /* Local timer */ timer@fffec600 { compatible = "arm,cortex-a9-twd-timer"; diff --git a/arch/arm/boot/dts/socfpga_arria5.dtsi b/arch/arm/boot/dts/socfpga_arria5.dtsi index a85b404..0feb15f 100644 --- a/arch/arm/boot/dts/socfpga_arria5.dtsi +++ b/arch/arm/boot/dts/socfpga_arria5.dtsi @@ -27,6 +27,18 @@ }; }; + dwmmc0@ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + samsung,dw-mshc-sdr-timing = <3 0>; + + slot@0 { + reg = <0>; + bus-width = <4>; + }; + }; + serial0@ffc02000 { clock-frequency = <100000000>; }; diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dtsi b/arch/arm/boot/dts/socfpga_cyclone5.dtsi index a8716f6..4ef4fa4 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5.dtsi +++ b/arch/arm/boot/dts/socfpga_cyclone5.dtsi @@ -28,6 +28,18 @@ }; }; + dwmmc0@ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + samsung,dw-mshc-sdr-timing = <3 0>; + + slot@0 { + reg = <0>; + bus-width = <4>; + }; + }; + ethernet@ff702000 { phy-mode = "rgmii"; phy-addr = <0xffffffff>; /* probe for phy addr */ diff --git a/arch/arm/boot/dts/socfpga_vt.dts b/arch/arm/boot/dts/socfpga_vt.dts index d1ec0ca..25b2653 100644 --- a/arch/arm/boot/dts/socfpga_vt.dts +++ b/arch/arm/boot/dts/socfpga_vt.dts @@ -41,6 +41,18 @@ }; }; + dwmmc0@ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + samsung,dw-mshc-sdr-timing = <3 0>; + + slot@0 { + reg = <0>; + bus-width = <4>; + }; + }; + ethernet@ff700000 { phy-mode = "gmii"; status = "okay";