new file mode 100644
@@ -0,0 +1,83 @@
+* Qualcomm SDHCI controller (sdhci-msm)
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-msm driver.
+
+Required properties:
+- compatible: Should contain "qcom,sdhci-msm".
+- reg: Base address and length of the register set listed in reg-names.
+- reg-names: Should contain the following:
+ "hc_mem" - Host controller register map
+ "core_mem" - SD Core register map
+- interrupts: Should contain an interrupt-specifiers for the interrupts listed in interrupt-names.
+- interrupt-names: Should contain the following:
+ "hc_irq" - Host controller interrupt
+ "pwr_irq" - PMIC interrupt
+- vdd-supply: Phandle to the regulator for the vdd (core voltage) supply.
+- vdd-io-supply: Phandle to the regulator for the vdd-io (i/o voltage) supply.
+- pinctrl-names: Should contain only one value - "default".
+- pinctrl-0: Should specify pin control groups used for this controller.
+- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
+- clock-names: Should contain the following:
+ "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required)
+ "core" - SDC MMC clock (MCLK) (required)
+ "bus" - SDCC bus voter clock (optional)
+
+Optional properties:
+
+- qcom,vdd-voltage-min - Specifies the minimum core voltage supported by the device in microvolts.
+- qcom,vdd-voltage-max - Specifies the maximum core voltage supported by the device in microvolts.
+- qcom,vdd-io-voltage-min - Specifies the minimum i/o voltage supported by the device in microvolts.
+- qcom,vdd-io-voltage-max - Specifies the maximum i/o voltage supported by the device in microvolts.
+
+Example:
+
+ sdhc_1: sdhci@f9824900 {
+ compatible = "qcom,sdhci-msm";
+ reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+ interrupts = <0 123 0>, <0 138 0>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ bus-width = <8>;
+ non-removable;
+
+ vdd-supply = <&pm8941_l20>;
+ vdd-io-supply = <&pm8941_s3>;
+
+ qcom,vdd-voltage-min = <2950000>;
+ qcom,vdd-voltage-max = <2950000>;
+ qcom,vdd-io-voltage-min = <1800000>;
+ qcom,vdd-io-voltage-max = <1800000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc1_clk &sdc1_cmd &sdc1_data>;
+
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
+ clock-names = "core", "iface";
+ };
+
+ sdhc_2: sdhci@f98a4900 {
+ compatible = "qcom,sdhci-msm";
+ reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+ interrupts = <0 1 2>;
+ #interrupt-cells = <1>;
+ interrupt-map = <0 &intc 0 125 0
+ 1 &intc 0 221 0>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ bus-width = <4>;
+
+ vdd-supply = <&pm8941_l21>;
+ vdd-io-supply = <&pm8941_l13>;
+
+ qcom,vdd-voltage-min = <2950000>;
+ qcom,vdd-voltage-max = <2950000>;
+ qcom,vdd-io-voltage-min = <1800000>;
+ qcom,vdd-io-voltage-max = <2950000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data>;
+
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
+ clock-names = "core", "iface";
+ };
This patch adds the device-tree binding documentation for Qualcomm SDHCI driver. It contains the differences between the core properties in mmc.txt and the properties used by the sdhci-msm driver. Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com> --- .../devicetree/bindings/mmc/sdhci-msm.txt | 83 ++++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-msm.txt