@@ -1148,6 +1148,9 @@ static u16 sdhci_get_preset_value(struct sdhci_host *host)
case MMC_TIMING_UHS_DDR50:
preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
break;
+ case MMC_TIMING_MMC_HS400:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_HS400);
+ break;
default:
pr_warn("%s: Invalid UHS-I mode selected\n",
mmc_hostname(host->mmc));
@@ -1475,6 +1478,8 @@ void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
else if ((timing == MMC_TIMING_UHS_DDR50) ||
(timing == MMC_TIMING_MMC_DDR52))
ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
+ else if (timing == MMC_TIMING_MMC_HS400)
+ ctrl_2 |= SDHCI_CTRL_HS400; /* Non-standard */
sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
}
EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
@@ -1546,7 +1551,8 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
u16 clk, ctrl_2;
/* In case of UHS-I modes, set High Speed Enable */
- if ((ios->timing == MMC_TIMING_MMC_HS200) ||
+ if ((ios->timing == MMC_TIMING_MMC_HS400) ||
+ (ios->timing == MMC_TIMING_MMC_HS200) ||
(ios->timing == MMC_TIMING_MMC_DDR52) ||
(ios->timing == MMC_TIMING_UHS_SDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR104) ||
@@ -1893,6 +1899,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
* tuning function has to be executed.
*/
switch (host->timing) {
+ case MMC_TIMING_MMC_HS400:
case MMC_TIMING_MMC_HS200:
case MMC_TIMING_UHS_SDR104:
break;
@@ -3120,6 +3127,10 @@ int sdhci_add_host(struct sdhci_host *host)
} else if (caps[1] & SDHCI_SUPPORT_SDR50)
mmc->caps |= MMC_CAP_UHS_SDR50;
+ if (host->quirks2 & SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 &&
+ (caps[1] & SDHCI_SUPPORT_HS400))
+ mmc->caps2 |= MMC_CAP2_HS400;
+
if ((mmc->caps2 & MMC_CAPS2_HSX00_1_2V) &&
(IS_ERR(mmc->supply.vqmmc) ||
!regulator_is_supported_voltage(mmc->supply.vqmmc, 1100000,
@@ -161,6 +161,7 @@
#define SDHCI_CTRL_UHS_SDR50 0x0002
#define SDHCI_CTRL_UHS_SDR104 0x0003
#define SDHCI_CTRL_UHS_DDR50 0x0004
+#define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
#define SDHCI_CTRL_VDD_180 0x0008
#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
#define SDHCI_CTRL_DRV_TYPE_B 0x0000
@@ -203,6 +204,7 @@
#define SDHCI_RETUNING_MODE_SHIFT 14
#define SDHCI_CLOCK_MUL_MASK 0x00FF0000
#define SDHCI_CLOCK_MUL_SHIFT 16
+#define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */
#define SDHCI_CAPABILITIES_1 0x44
@@ -235,6 +237,7 @@
#define SDHCI_PRESET_FOR_SDR50 0x6A
#define SDHCI_PRESET_FOR_SDR104 0x6C
#define SDHCI_PRESET_FOR_DDR50 0x6E
+#define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
#define SDHCI_PRESET_DRV_MASK 0xC000
#define SDHCI_PRESET_DRV_SHIFT 14
#define SDHCI_PRESET_CLKGEN_SEL_MASK 0x400
@@ -104,6 +104,8 @@ struct sdhci_host {
#define SDHCI_QUIRK2_BROKEN_64_BIT_DMA (1<<9)
/* need clear transfer mode register before send cmd */
#define SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD (1<<10)
+/* Capability register bit-63 indicates HS400 support */
+#define SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 (1<<11)
int irq; /* Device IRQ */
void __iomem *ioaddr; /* Mapped address */
MMC core already has support for HS400. Add HS400 support to SDHCI driver. The SDHC Standard specification does not define HS400 so consequently HS400 support is non-standard. However HS400 is not selected without the host controller setting the corresponding capability flags so host controllers not yet supporting HS400 will not be affected. To support that, a quirk SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to enable the use of capabilities register reserved bit-63 to indicate HS400 support. Because HS400 is non-standard for SDHCI, it is possible that different vendors will do things in different ways. However HS200 support faced the same issue but currently there is only one solution. As such, no attempt has been made to provide for alternate HS400 solutions except for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> --- drivers/mmc/host/sdhci.c | 13 ++++++++++++- drivers/mmc/host/sdhci.h | 3 +++ include/linux/mmc/sdhci.h | 2 ++ 3 files changed, 17 insertions(+), 1 deletion(-)