diff mbox

[2/3] mmc: dw_mmc: Generic MMC tuning with the clock phase framework

Message ID 1418943663-10012-3-git-send-email-amstan@chromium.org (mailing list archive)
State New, archived
Headers show

Commit Message

Alexandru M Stan Dec. 18, 2014, 11:01 p.m. UTC
This algorithm will try 5 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing many
tunings yields better results since some tests are run more than once(ex: if the
underlying driver uses 45 degree increments, the tuning code will try the same
angle more than once).

It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.

We do not touch ciu_drive (and by extension define default-drive-phase). Drive
phase is mostly used to define minimum hold times, while one could write some
code to determine what phase meets the minimum hold time (ex 10 degrees) this
will not work with the current clock phase framework (which floors angles, so
we'll get 0 deg, and there's no way to know what resolution the floors happen
at). We assume that the default drive angles set by the hardware are good enough.

If a device has device specific code (like exynos) then that will still take
precedence, otherwise this new code will execute. If the device wants to tune,
but has no sample_clk defined we'll return EIO with an error message.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Doug Anderson <dianders@chromium.org>
---
 drivers/mmc/host/dw_mmc.c  | 189 +++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mmc/dw_mmc.h |   3 +
 2 files changed, 192 insertions(+)

Comments

Doug Anderson Dec. 19, 2014, 12:20 a.m. UTC | #1
Alex,

On Thu, Dec 18, 2014 at 3:01 PM, Alexandru M Stan <amstan@chromium.org> wrote:
> +       blk_test = kmalloc(blksz, GFP_KERNEL);
> +       if (!blk_test)
> +               return -ENOMEM;
> +
> +       ranges = kmalloc(((NUM_PHASES / 2 + 1) * sizeof(ranges)), GFP_KERNEL);

sizeof(*ranges)


Other than that, this looks good to me and you can add my reviewed-by
when the above is fixed.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Ulf Hansson Dec. 19, 2014, 8:51 a.m. UTC | #2
On 19 December 2014 at 00:01, Alexandru M Stan <amstan@chromium.org> wrote:
> This algorithm will try 5 degree increments, since there's no way to tell
> what resolution the underlying phase code uses. As an added bonus, doing many
> tunings yields better results since some tests are run more than once(ex: if the
> underlying driver uses 45 degree increments, the tuning code will try the same
> angle more than once).
>
> It will then construct a list of good phase ranges (even ranges that cross
> 360/0), will pick the biggest range then it will set the sample_clk to the
> middle of that range.
>
> We do not touch ciu_drive (and by extension define default-drive-phase). Drive
> phase is mostly used to define minimum hold times, while one could write some
> code to determine what phase meets the minimum hold time (ex 10 degrees) this
> will not work with the current clock phase framework (which floors angles, so
> we'll get 0 deg, and there's no way to know what resolution the floors happen
> at). We assume that the default drive angles set by the hardware are good enough.
>
> If a device has device specific code (like exynos) then that will still take
> precedence, otherwise this new code will execute. If the device wants to tune,
> but has no sample_clk defined we'll return EIO with an error message.
>
> Signed-off-by: Alexandru M Stan <amstan@chromium.org>
> Suggested-by: Heiko Stuebner <heiko@sntech.de>
> Suggested-by: Doug Anderson <dianders@chromium.org>
> ---
>  drivers/mmc/host/dw_mmc.c  | 189 +++++++++++++++++++++++++++++++++++++++++++++
>  include/linux/mmc/dw_mmc.h |   3 +
>  2 files changed, 192 insertions(+)
>
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 69f0cc6..b59c221 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -984,6 +984,12 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
>         if (drv_data && drv_data->set_ios)
>                 drv_data->set_ios(slot->host, ios);
>
> +       /* Make sure we use phases which we can enumerate with */
> +       if (!IS_ERR(slot->host->sample_clk)) {
> +               clk_set_phase(slot->host->sample_clk,
> +                             slot->host->default_sample_phase);
> +       }
> +
>         /* Slot specific timing and width adjustment */
>         dw_mci_setup_bus(slot, false);
>
> @@ -1187,6 +1193,174 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
>         }
>  }
>
> +static int dw_mci_tuning_test(struct dw_mci_slot *slot, u32 opcode,
> +                              struct dw_mci_tuning_data *tuning_data,
> +                              u8 *blk_test)
> +{
> +       struct dw_mci *host = slot->host;
> +       struct mmc_host *mmc = slot->mmc;
> +       const u8 *blk_pattern = tuning_data->blk_pattern;
> +       unsigned int blksz = tuning_data->blksz;
> +       struct mmc_request mrq = { NULL };
> +       struct mmc_command cmd = {0};
> +       struct mmc_command stop = {0};
> +       struct mmc_data data = {0};
> +       struct scatterlist sg;
> +
> +       memset(blk_test, 0, blksz);
> +
> +       cmd.opcode = opcode;
> +       cmd.arg = 0;
> +       cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
> +
> +       stop.opcode = MMC_STOP_TRANSMISSION;
> +       stop.arg = 0;
> +       stop.flags = MMC_RSP_R1B | MMC_CMD_AC;
> +
> +       data.blksz = blksz;
> +       data.blocks = 1;
> +       data.flags = MMC_DATA_READ;
> +       data.sg = &sg;
> +       data.sg_len = 1;
> +
> +       sg_init_one(&sg, blk_test, blksz);
> +       mrq.cmd = &cmd;
> +       mrq.stop = &stop;
> +       mrq.data = &data;
> +       host->mrq = &mrq;
> +
> +       mci_writel(host, TMOUT, ~0);
> +
> +       mmc_wait_for_req(mmc, &mrq);
> +
> +       if (!cmd.error && !data.error) {
> +               if (!memcmp(blk_pattern, blk_test, blksz))
> +                       return 0;
> +               return -EIO;
> +       } else {
> +               dev_dbg(host->dev,
> +                       "Tuning error: cmd.error:%d, data.error:%d\n",
> +                       cmd.error, data.error);
> +               if (cmd.error)
> +                       return cmd.error;
> +               else
> +                       return data.error;
> +       }

This function should be simplified using mmc_send_tuning().

Now, dw_mmc seems to have some issues that it needs the tuning command
to have a stop command sent as well. That's not according to the eMMC
spec.

Please have a look at this patch:
http://www.spinics.net/lists/linux-mmc/msg29807.html

Kind regards
Uffe

> +}
> +
> +static int dw_mci_execute_generic_tuning(struct dw_mci_slot *slot, u32 opcode,
> +                                        struct dw_mci_tuning_data *tuning_data)
> +{
> +       struct dw_mci *host = slot->host;
> +       unsigned int blksz = tuning_data->blksz;
> +       u8 *blk_test;
> +       int ret = 0;
> +       int i;
> +       bool v, prev_v = 0, first_v;
> +       struct range_t {
> +               int start;
> +               int end; /* inclusive */
> +       };
> +       struct range_t *ranges;
> +       unsigned int range_count = 0;
> +       int longest_range_len = -1;
> +       int longest_range = -1;
> +       int middle_phase;
> +       const int PHASE_INCREMENT = 5;
> +       const int NUM_PHASES = 360 / PHASE_INCREMENT;
> +
> +       if (IS_ERR(host->sample_clk)) {
> +               dev_err(host->dev, "Tuning clock (sample_clk) not defined.\n");
> +               return -EIO;
> +       }
> +
> +       blk_test = kmalloc(blksz, GFP_KERNEL);
> +       if (!blk_test)
> +               return -ENOMEM;
> +
> +       ranges = kmalloc(((NUM_PHASES / 2 + 1) * sizeof(ranges)), GFP_KERNEL);
> +       if (!blk_test) {
> +               ret = -ENOMEM;
> +               goto free_blk_test;
> +       }
> +
> +       /* Try each phase and extract good ranges */
> +       for (i = 0; i < NUM_PHASES; i++) {
> +               clk_set_phase(host->sample_clk, i * PHASE_INCREMENT);
> +
> +               v = !dw_mci_tuning_test(slot, opcode, tuning_data, blk_test);
> +
> +               if ((!prev_v) && v) {
> +                       range_count++;
> +                       ranges[range_count-1].start = i;
> +               }
> +               if (v) {
> +                       ranges[range_count-1].end = i;
> +               }
> +
> +               if (i == 0)
> +                       first_v = v;
> +
> +               prev_v = v;
> +       }
> +
> +       if (range_count == 0) {
> +               dev_info(host->dev, "All phases bad!");
> +               ret = -EIO;
> +               goto free;
> +       }
> +
> +       /* wrap around case, merge the end points */
> +       if ((range_count > 1) && first_v && v) {
> +               ranges[0].start = ranges[range_count-1].start;
> +               range_count--;
> +       }
> +
> +       if ((ranges[0].start == 0) && (ranges[0].end == NUM_PHASES - 1)) {
> +               clk_set_phase(host->sample_clk, host->default_sample_phase);
> +               dev_info(host->dev, "All phases work, using default phase %d.",
> +                       host->default_sample_phase);
> +               goto free;
> +       }
> +
> +       /* Find the longest range */
> +       for (i = 0; i < range_count; i++) {
> +               int len = (ranges[i].end - ranges[i].start + 1);
> +               if (len < 0)
> +                       len += NUM_PHASES;
> +
> +               if (longest_range_len < len) {
> +                       longest_range_len = len;
> +                       longest_range = i;
> +               }
> +
> +               dev_dbg(host->dev, "Good phase range %d-%d (%d len)\n",
> +                       ranges[i].start * PHASE_INCREMENT,
> +                       ranges[i].end * PHASE_INCREMENT,
> +                       len
> +               );
> +       }
> +
> +       dev_dbg(host->dev, "Best phase range %d-%d (%d len)\n",
> +               ranges[longest_range].start * PHASE_INCREMENT,
> +               ranges[longest_range].end * PHASE_INCREMENT,
> +               longest_range_len
> +       );
> +
> +       middle_phase = ranges[longest_range].start + longest_range_len / 2;
> +       middle_phase %= NUM_PHASES;
> +       dev_info(host->dev, "Successfully tuned phase to %d\n",
> +               middle_phase * PHASE_INCREMENT);
> +
> +       clk_set_phase(host->sample_clk, middle_phase * PHASE_INCREMENT);
> +
> +free:
> +       kfree(ranges);
> +free_blk_test:
> +       kfree(blk_test);
> +       return ret;
> +}
> +
>  static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
>  {
>         struct dw_mci_slot *slot = mmc_priv(mmc);
> @@ -1216,6 +1390,8 @@ static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
>
>         if (drv_data && drv_data->execute_tuning)
>                 err = drv_data->execute_tuning(slot, opcode, &tuning_data);
> +       else
> +               err = dw_mci_execute_generic_tuning(slot, opcode, &tuning_data);
>         return err;
>  }
>
> @@ -2492,6 +2668,11 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
>         if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
>                 pdata->bus_hz = clock_frequency;
>
> +       if (of_property_read_u32(np, "default-sample-phase",
> +                                       &host->default_sample_phase)) {
> +               host->default_sample_phase = 0;
> +       }
> +
>         if (drv_data && drv_data->parse_dt) {
>                 ret = drv_data->parse_dt(host);
>                 if (ret)
> @@ -2564,6 +2745,14 @@ int dw_mci_probe(struct dw_mci *host)
>                 host->bus_hz = clk_get_rate(host->ciu_clk);
>         }
>
> +       host->drv_clk = devm_clk_get(host->dev, "ciu_drv");
> +       if (IS_ERR(host->drv_clk))
> +               dev_dbg(host->dev, "ciu_drv not available\n");
> +
> +       host->sample_clk = devm_clk_get(host->dev, "ciu_sample");
> +       if (IS_ERR(host->sample_clk))
> +               dev_dbg(host->dev, "ciu_sample not available\n");
> +
>         if (!host->bus_hz) {
>                 dev_err(host->dev,
>                         "Platform data must supply bus speed\n");
> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> index 0013669..335e2f3 100644
> --- a/include/linux/mmc/dw_mmc.h
> +++ b/include/linux/mmc/dw_mmc.h
> @@ -172,7 +172,10 @@ struct dw_mci {
>         void                    *priv;
>         struct clk              *biu_clk;
>         struct clk              *ciu_clk;
> +       struct clk              *drv_clk;
> +       struct clk              *sample_clk;
>         struct dw_mci_slot      *slot[MAX_MCI_SLOTS];
> +       int                     default_sample_phase;
>
>         /* FIFO push and pull */
>         int                     fifo_depth;
> --
> 2.2.0.rc0.207.ga3a616c
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Stephen Boyd Dec. 19, 2014, 6:29 p.m. UTC | #3
On 12/18/2014 04:20 PM, Doug Anderson wrote:
> Alex,
>
> On Thu, Dec 18, 2014 at 3:01 PM, Alexandru M Stan <amstan@chromium.org> wrote:
>> +       blk_test = kmalloc(blksz, GFP_KERNEL);
>> +       if (!blk_test)
>> +               return -ENOMEM;
>> +
>> +       ranges = kmalloc(((NUM_PHASES / 2 + 1) * sizeof(ranges)), GFP_KERNEL);
> sizeof(*ranges)
>
>
> Other than that, this looks good to me and you can add my reviewed-by
> when the above is fixed.
>
>

Might want to use kmalloc_array() too.
diff mbox

Patch

diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 69f0cc6..b59c221 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -984,6 +984,12 @@  static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	if (drv_data && drv_data->set_ios)
 		drv_data->set_ios(slot->host, ios);
 
+	/* Make sure we use phases which we can enumerate with */
+	if (!IS_ERR(slot->host->sample_clk)) {
+		clk_set_phase(slot->host->sample_clk,
+			      slot->host->default_sample_phase);
+	}
+
 	/* Slot specific timing and width adjustment */
 	dw_mci_setup_bus(slot, false);
 
@@ -1187,6 +1193,174 @@  static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
 	}
 }
 
+static int dw_mci_tuning_test(struct dw_mci_slot *slot, u32 opcode,
+			       struct dw_mci_tuning_data *tuning_data,
+			       u8 *blk_test)
+{
+	struct dw_mci *host = slot->host;
+	struct mmc_host *mmc = slot->mmc;
+	const u8 *blk_pattern = tuning_data->blk_pattern;
+	unsigned int blksz = tuning_data->blksz;
+	struct mmc_request mrq = { NULL };
+	struct mmc_command cmd = {0};
+	struct mmc_command stop = {0};
+	struct mmc_data data = {0};
+	struct scatterlist sg;
+
+	memset(blk_test, 0, blksz);
+
+	cmd.opcode = opcode;
+	cmd.arg = 0;
+	cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+
+	stop.opcode = MMC_STOP_TRANSMISSION;
+	stop.arg = 0;
+	stop.flags = MMC_RSP_R1B | MMC_CMD_AC;
+
+	data.blksz = blksz;
+	data.blocks = 1;
+	data.flags = MMC_DATA_READ;
+	data.sg = &sg;
+	data.sg_len = 1;
+
+	sg_init_one(&sg, blk_test, blksz);
+	mrq.cmd = &cmd;
+	mrq.stop = &stop;
+	mrq.data = &data;
+	host->mrq = &mrq;
+
+	mci_writel(host, TMOUT, ~0);
+
+	mmc_wait_for_req(mmc, &mrq);
+
+	if (!cmd.error && !data.error) {
+		if (!memcmp(blk_pattern, blk_test, blksz))
+			return 0;
+		return -EIO;
+	} else {
+		dev_dbg(host->dev,
+			"Tuning error: cmd.error:%d, data.error:%d\n",
+			cmd.error, data.error);
+		if (cmd.error)
+			return cmd.error;
+		else
+			return data.error;
+	}
+}
+
+static int dw_mci_execute_generic_tuning(struct dw_mci_slot *slot, u32 opcode,
+					 struct dw_mci_tuning_data *tuning_data)
+{
+	struct dw_mci *host = slot->host;
+	unsigned int blksz = tuning_data->blksz;
+	u8 *blk_test;
+	int ret = 0;
+	int i;
+	bool v, prev_v = 0, first_v;
+	struct range_t {
+		int start;
+		int end; /* inclusive */
+	};
+	struct range_t *ranges;
+	unsigned int range_count = 0;
+	int longest_range_len = -1;
+	int longest_range = -1;
+	int middle_phase;
+	const int PHASE_INCREMENT = 5;
+	const int NUM_PHASES = 360 / PHASE_INCREMENT;
+
+	if (IS_ERR(host->sample_clk)) {
+		dev_err(host->dev, "Tuning clock (sample_clk) not defined.\n");
+		return -EIO;
+	}
+
+	blk_test = kmalloc(blksz, GFP_KERNEL);
+	if (!blk_test)
+		return -ENOMEM;
+
+	ranges = kmalloc(((NUM_PHASES / 2 + 1) * sizeof(ranges)), GFP_KERNEL);
+	if (!blk_test) {
+		ret = -ENOMEM;
+		goto free_blk_test;
+	}
+
+	/* Try each phase and extract good ranges */
+	for (i = 0; i < NUM_PHASES; i++) {
+		clk_set_phase(host->sample_clk, i * PHASE_INCREMENT);
+
+		v = !dw_mci_tuning_test(slot, opcode, tuning_data, blk_test);
+
+		if ((!prev_v) && v) {
+			range_count++;
+			ranges[range_count-1].start = i;
+		}
+		if (v) {
+			ranges[range_count-1].end = i;
+		}
+
+		if (i == 0)
+			first_v = v;
+
+		prev_v = v;
+	}
+
+	if (range_count == 0) {
+		dev_info(host->dev, "All phases bad!");
+		ret = -EIO;
+		goto free;
+	}
+
+	/* wrap around case, merge the end points */
+	if ((range_count > 1) && first_v && v) {
+		ranges[0].start = ranges[range_count-1].start;
+		range_count--;
+	}
+
+	if ((ranges[0].start == 0) && (ranges[0].end == NUM_PHASES - 1)) {
+		clk_set_phase(host->sample_clk, host->default_sample_phase);
+		dev_info(host->dev, "All phases work, using default phase %d.",
+			host->default_sample_phase);
+		goto free;
+	}
+
+	/* Find the longest range */
+	for (i = 0; i < range_count; i++) {
+		int len = (ranges[i].end - ranges[i].start + 1);
+		if (len < 0)
+			len += NUM_PHASES;
+
+		if (longest_range_len < len) {
+			longest_range_len = len;
+			longest_range = i;
+		}
+
+		dev_dbg(host->dev, "Good phase range %d-%d (%d len)\n",
+			ranges[i].start * PHASE_INCREMENT,
+			ranges[i].end * PHASE_INCREMENT,
+			len
+		);
+	}
+
+	dev_dbg(host->dev, "Best phase range %d-%d (%d len)\n",
+		ranges[longest_range].start * PHASE_INCREMENT,
+		ranges[longest_range].end * PHASE_INCREMENT,
+		longest_range_len
+	);
+
+	middle_phase = ranges[longest_range].start + longest_range_len / 2;
+	middle_phase %= NUM_PHASES;
+	dev_info(host->dev, "Successfully tuned phase to %d\n",
+		middle_phase * PHASE_INCREMENT);
+
+	clk_set_phase(host->sample_clk, middle_phase * PHASE_INCREMENT);
+
+free:
+	kfree(ranges);
+free_blk_test:
+	kfree(blk_test);
+	return ret;
+}
+
 static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
 {
 	struct dw_mci_slot *slot = mmc_priv(mmc);
@@ -1216,6 +1390,8 @@  static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
 
 	if (drv_data && drv_data->execute_tuning)
 		err = drv_data->execute_tuning(slot, opcode, &tuning_data);
+	else
+		err = dw_mci_execute_generic_tuning(slot, opcode, &tuning_data);
 	return err;
 }
 
@@ -2492,6 +2668,11 @@  static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
 	if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
 		pdata->bus_hz = clock_frequency;
 
+	if (of_property_read_u32(np, "default-sample-phase",
+					&host->default_sample_phase)) {
+		host->default_sample_phase = 0;
+	}
+
 	if (drv_data && drv_data->parse_dt) {
 		ret = drv_data->parse_dt(host);
 		if (ret)
@@ -2564,6 +2745,14 @@  int dw_mci_probe(struct dw_mci *host)
 		host->bus_hz = clk_get_rate(host->ciu_clk);
 	}
 
+	host->drv_clk = devm_clk_get(host->dev, "ciu_drv");
+	if (IS_ERR(host->drv_clk))
+		dev_dbg(host->dev, "ciu_drv not available\n");
+
+	host->sample_clk = devm_clk_get(host->dev, "ciu_sample");
+	if (IS_ERR(host->sample_clk))
+		dev_dbg(host->dev, "ciu_sample not available\n");
+
 	if (!host->bus_hz) {
 		dev_err(host->dev,
 			"Platform data must supply bus speed\n");
diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
index 0013669..335e2f3 100644
--- a/include/linux/mmc/dw_mmc.h
+++ b/include/linux/mmc/dw_mmc.h
@@ -172,7 +172,10 @@  struct dw_mci {
 	void			*priv;
 	struct clk		*biu_clk;
 	struct clk		*ciu_clk;
+	struct clk		*drv_clk;
+	struct clk		*sample_clk;
 	struct dw_mci_slot	*slot[MAX_MCI_SLOTS];
+	int			default_sample_phase;
 
 	/* FIFO push and pull */
 	int			fifo_depth;