@@ -929,6 +929,7 @@ static void sdhci_finish_data(struct sdhci_host *host)
data = host->data;
host->data = NULL;
+ host->data_cmd = NULL;
if ((host->flags & (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA)) ==
(SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA))
@@ -1014,6 +1015,10 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
host->cmd = cmd;
host->busy_handle = 0;
+ if (cmd->data || cmd->flags & MMC_RSP_BUSY) {
+ WARN_ON(host->data_cmd);
+ host->data_cmd = cmd;
+ }
sdhci_prepare_data(host, cmd);
@@ -2218,6 +2223,7 @@ static void sdhci_tasklet_finish(unsigned long param)
host->mrq = NULL;
host->cmd = NULL;
host->data = NULL;
+ host->data_cmd = NULL;
sdhci_led_deactivate(host);
@@ -2359,14 +2365,19 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
}
if (!host->data) {
+ struct mmc_command *data_cmd = host->data_cmd;
+
+ if (data_cmd)
+ host->data_cmd = NULL;
+
/*
* The "data complete" interrupt is also used to
* indicate that a busy state has ended. See comment
* above in sdhci_cmd_irq().
*/
- if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
+ if (data_cmd && (data_cmd->flags & MMC_RSP_BUSY)) {
if (intmask & SDHCI_INT_DATA_TIMEOUT) {
- host->cmd->error = -ETIMEDOUT;
+ data_cmd->error = -ETIMEDOUT;
tasklet_schedule(&host->finish_tasklet);
return;
}
@@ -2441,7 +2452,7 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
}
if (intmask & SDHCI_INT_DATA_END) {
- if (host->cmd) {
+ if (host->cmd == host->data_cmd) {
/*
* Data managed to finish before the
* command completed. Make sure we do
@@ -463,6 +463,7 @@ struct sdhci_host {
struct mmc_request *mrq; /* Current request */
struct mmc_command *cmd; /* Current command */
+ struct mmc_command *data_cmd; /* Current data command */
struct mmc_data *data; /* Current data request */
unsigned int data_early:1; /* Data finished before cmd */
unsigned int busy_handle:1; /* Handling the order of Busy-end */
In order to support commands during data transfer, there must be a distinction between the command that is using the command line (and for which a command interrupt is expected) and the command that is using the data lines (for which a data interrupt is expected). There is host->cmd for the command line, but there is only host->data for the data lines, which is a different structure, does not represent the command in use, and is anyway NULL in the case of commands that use the data lines for busy signalling instead of data transfer. Introduce host->data_cmd to record what command is using the data lines, and use that instead of host->cmd when referring to the data command. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> --- drivers/mmc/host/sdhci.c | 17 ++++++++++++++--- drivers/mmc/host/sdhci.h | 1 + 2 files changed, 15 insertions(+), 3 deletions(-)