| Message ID | 1468309584-3591-13-git-send-email-aisheng.dong@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 12/07/16 10:46, Dong Aisheng wrote: > Move all hw related static initializations into a separate function > which helps concentrate the hw related initialization code. > And that function could also be called by other places later as a > basic hw state restore. > e.g. suspend/resume where the hw state is possible to lost due to > low power mode. > > Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> > --- > drivers/mmc/host/sdhci-esdhc-imx.c | 72 +++++++++++++++++++++----------------- > 1 file changed, 40 insertions(+), 32 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c > index bbb0bd4eac28..5a0e5dee977f 100644 > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > @@ -979,6 +979,44 @@ static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = { > .ops = &sdhci_esdhc_ops, > }; > > +static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); > + > + if (esdhc_is_usdhc(imx_data)) { > + /* > + * The imx6q ROM code will change the default watermark > + * level setting to something insane. Change it back here. > + */ > + writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); > + > + /* > + * ROM code will change the bit burst_length_enable setting > + * to zero if this usdhc is choosed to boot system. Change > + * it back here, otherwise it will impact the performance a > + * lot. This bit is used to enable/disable the burst length > + * for the external AHB2AXI bridge, it's usefully especially > + * for INCR transfer because without burst length indicator, > + * the AHB2AXI bridge does not know the burst length in > + * advance. And without burst length indicator, AHB INCR > + * transfer can only be converted to singles on the AXI side. > + */ > + writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) > + | ESDHC_BURST_LEN_EN_INCR, > + host->ioaddr + SDHCI_HOST_CONTROL); > + /* > + * errata ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL > + * TO1.1, it's harmless for MX6SL > + */ > + writel(readl(host->ioaddr + 0x6c) | BIT(7), > + host->ioaddr + 0x6c); > + > + /* disable DLL_CTRL delay line settings */ > + writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); > + } > +} > + > #ifdef CONFIG_OF > static int > sdhci_esdhc_imx_probe_dt(struct platform_device *pdev, > @@ -1176,43 +1214,11 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev) > host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK > | SDHCI_QUIRK_BROKEN_ADMA; > > - /* > - * The imx6q ROM code will change the default watermark level setting > - * to something insane. Change it back here. > - */ > if (esdhc_is_usdhc(imx_data)) { > - writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); > - > host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN; > host->mmc->caps |= MMC_CAP_1_8V_DDR; > - > - /* > - * ROM code will change the bit burst_length_enable setting > - * to zero if this usdhc is choosed to boot system. Change > - * it back here, otherwise it will impact the performance a > - * lot. This bit is used to enable/disable the burst length > - * for the external AHB2AXI bridge, it's usefully especially > - * for INCR transfer because without burst length indicator, > - * the AHB2AXI bridge does not know the burst length in > - * advance. And without burst length indicator, AHB INCR > - * transfer can only be converted to singles on the AXI side. > - */ > - writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) > - | ESDHC_BURST_LEN_EN_INCR, > - host->ioaddr + SDHCI_HOST_CONTROL); > - > if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200)) > host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200; > - > - /* > - * errata ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL > - * TO1.1, it's harmless for MX6SL > - */ > - writel(readl(host->ioaddr + 0x6c) | BIT(7), > - host->ioaddr + 0x6c); > - > - /* disable DLL_CTRL delay line settings */ > - writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); > } > > if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) > @@ -1237,6 +1243,8 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev) > if (err) > goto disable_clk; > > + sdhci_esdhc_imx_hwinit(host); > + > err = sdhci_add_host(host); > if (err) > goto disable_clk; > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index bbb0bd4eac28..5a0e5dee977f 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -979,6 +979,44 @@ static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = { .ops = &sdhci_esdhc_ops, }; +static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); + + if (esdhc_is_usdhc(imx_data)) { + /* + * The imx6q ROM code will change the default watermark + * level setting to something insane. Change it back here. + */ + writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); + + /* + * ROM code will change the bit burst_length_enable setting + * to zero if this usdhc is choosed to boot system. Change + * it back here, otherwise it will impact the performance a + * lot. This bit is used to enable/disable the burst length + * for the external AHB2AXI bridge, it's usefully especially + * for INCR transfer because without burst length indicator, + * the AHB2AXI bridge does not know the burst length in + * advance. And without burst length indicator, AHB INCR + * transfer can only be converted to singles on the AXI side. + */ + writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) + | ESDHC_BURST_LEN_EN_INCR, + host->ioaddr + SDHCI_HOST_CONTROL); + /* + * errata ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL + * TO1.1, it's harmless for MX6SL + */ + writel(readl(host->ioaddr + 0x6c) | BIT(7), + host->ioaddr + 0x6c); + + /* disable DLL_CTRL delay line settings */ + writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); + } +} + #ifdef CONFIG_OF static int sdhci_esdhc_imx_probe_dt(struct platform_device *pdev, @@ -1176,43 +1214,11 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev) host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK | SDHCI_QUIRK_BROKEN_ADMA; - /* - * The imx6q ROM code will change the default watermark level setting - * to something insane. Change it back here. - */ if (esdhc_is_usdhc(imx_data)) { - writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); - host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN; host->mmc->caps |= MMC_CAP_1_8V_DDR; - - /* - * ROM code will change the bit burst_length_enable setting - * to zero if this usdhc is choosed to boot system. Change - * it back here, otherwise it will impact the performance a - * lot. This bit is used to enable/disable the burst length - * for the external AHB2AXI bridge, it's usefully especially - * for INCR transfer because without burst length indicator, - * the AHB2AXI bridge does not know the burst length in - * advance. And without burst length indicator, AHB INCR - * transfer can only be converted to singles on the AXI side. - */ - writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) - | ESDHC_BURST_LEN_EN_INCR, - host->ioaddr + SDHCI_HOST_CONTROL); - if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200)) host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200; - - /* - * errata ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL - * TO1.1, it's harmless for MX6SL - */ - writel(readl(host->ioaddr + 0x6c) | BIT(7), - host->ioaddr + 0x6c); - - /* disable DLL_CTRL delay line settings */ - writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); } if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) @@ -1237,6 +1243,8 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev) if (err) goto disable_clk; + sdhci_esdhc_imx_hwinit(host); + err = sdhci_add_host(host); if (err) goto disable_clk;
Move all hw related static initializations into a separate function which helps concentrate the hw related initialization code. And that function could also be called by other places later as a basic hw state restore. e.g. suspend/resume where the hw state is possible to lost due to low power mode. Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> --- drivers/mmc/host/sdhci-esdhc-imx.c | 72 +++++++++++++++++++++----------------- 1 file changed, 40 insertions(+), 32 deletions(-)