diff mbox series

[RFC,v3.1,09/27] mmc: sdhci: add UHS-II related definitions in headers

Message ID 20201106022726.19831-10-takahiro.akashi@linaro.org (mailing list archive)
State New, archived
Headers show
Series Add support UHS-II for GL9755 | expand

Commit Message

AKASHI Takahiro Nov. 6, 2020, 2:27 a.m. UTC
Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.

Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
---
 drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sdhci.h      |  73 +++++++++++-
 2 files changed, 282 insertions(+), 1 deletion(-)
 create mode 100644 drivers/mmc/host/sdhci-uhs2.h

Comments

Adrian Hunter Nov. 26, 2020, 8:15 a.m. UTC | #1
On 6/11/20 4:27 am, AKASHI Takahiro wrote:
> Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.
> 
> Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
> ---
>  drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++
>  drivers/mmc/host/sdhci.h      |  73 +++++++++++-
>  2 files changed, 282 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> 
> diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> new file mode 100644
> index 000000000000..3b157df9c89c
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-uhs2.h
> @@ -0,0 +1,210 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + *  linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
> + *  Interface driver
> + *
> + * Header file for Host Controller UHS2 related registers and I/O accessors.
> + *
> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> + */
> +#ifndef __SDHCI_UHS2_H
> +#define __SDHCI_UHS2_H
> +
> +#include <linux/bits.h>
> +
> +/*
> + * UHS-II Controller registers
> + * 0x74 preset in sdhci.h
> + * 0x80
> + * 0x84-0xB4
> + * 0xB8-0xCF
> + * 0xE0-0xE7
> + */
> +/* UHS2 */
> +#define SDHCI_UHS2_BLOCK_SIZE	0x80
> +#define  SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \
> +	((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
> +
> +#define SDHCI_UHS2_BLOCK_COUNT	0x84
> +
> +#define SDHCI_UHS2_CMD_PACKET	0x88
> +#define  SDHCI_UHS2_CMD_PACK_MAX_LEN	20
> +
> +#define SDHCI_UHS2_TRANS_MODE	0x9C
> +#define  SDHCI_UHS2_TRNS_DMA		BIT(0)
> +#define  SDHCI_UHS2_TRNS_BLK_CNT_EN	BIT(1)
> +#define  SDHCI_UHS2_TRNS_DATA_TRNS_WRT	BIT(4)
> +#define  SDHCI_UHS2_TRNS_BLK_BYTE_MODE	BIT(5)
> +#define  SDHCI_UHS2_TRNS_RES_R5		BIT(6)
> +#define  SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN	BIT(7)
> +#define  SDHCI_UHS2_TRNS_RES_INT_DIS	BIT(8)
> +#define  SDHCI_UHS2_TRNS_WAIT_EBSY	BIT(14)
> +#define  SDHCI_UHS2_TRNS_2L_HD		BIT(15)
> +
> +#define SDHCI_UHS2_COMMAND	0x9E
> +#define  SDHCI_UHS2_COMMAND_SUB_CMD	0x0004
> +#define  SDHCI_UHS2_COMMAND_DATA	0x0020
> +#define  SDHCI_UHS2_COMMAND_TRNS_ABORT	0x0040
> +#define  SDHCI_UHS2_COMMAND_CMD12	0x0080
> +#define  SDHCI_UHS2_COMMAND_DORMANT	0x00C0
> +#define  SDHCI_UHS2_COMMAND_PACK_LEN_MASK	GENMASK(12,8)
> +#define  SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT	8
> +
> +#define SDHCI_UHS2_RESPONSE	0xA0
> +#define  SDHCI_UHS2_RESPONSE_MAX_LEN	20
> +
> +#define SDHCI_UHS2_MSG_SELECT	0xB4
> +#define SDHCI_UHS2_MSG_SELECT_CURR	0x0
> +#define SDHCI_UHS2_MSG_SELECT_ONE	0x1
> +#define SDHCI_UHS2_MSG_SELECT_TWO	0x2
> +#define SDHCI_UHS2_MSG_SELECT_THREE	0x3
> +
> +#define SDHCI_UHS2_MSG		0xB8
> +
> +#define SDHCI_UHS2_DEV_INT_STATUS	0xBC
> +
> +#define SDHCI_UHS2_DEV_SELECT	0xBE
> +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK	GENMASK(3,0)
> +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN	BIT(7)
> +
> +#define SDHCI_UHS2_DEV_INT_CODE	0xBF
> +
> +#define SDHCI_UHS2_SW_RESET	0xC0
> +#define SDHCI_UHS2_SW_RESET_FULL	0x0001
> +#define SDHCI_UHS2_SW_RESET_SD		0x0002
> +
> +#define SDHCI_UHS2_TIMER_CTRL	0xC2
> +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT	4
> +
> +#define SDHCI_UHS2_ERR_INT_STATUS		0xC4
> +#define SDHCI_UHS2_ERR_INT_STATUS_EN		0xC8
> +#define SDHCI_UHS2_ERR_INT_SIG_EN		0xCC
> +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER	BIT(0)
> +#define SDHCI_UHS2_ERR_INT_STATUS_RES		BIT(1)
> +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP	BIT(2)
> +#define SDHCI_UHS2_ERR_INT_STATUS_CRC		BIT(3)
> +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME		BIT(4)
> +#define SDHCI_UHS2_ERR_INT_STATUS_TID		BIT(5)
> +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER	BIT(7)
> +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY		BIT(8)
> +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA		BIT(15)
> +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT	BIT(16)
> +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT	BIT(17)
> +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR	BIT(27)
> +#define SDHCI_UHS2_ERR_INT_STATUS_MASK	\
> +		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK	\
> +		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT)
> +/* CRC Error occurs during a packet receiving */
> +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK	\
> +		(SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
> +		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
> +		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> +
> +#define SDHCI_UHS2_SET_PTR	0xE0
> +#define   SDHCI_UHS2_GEN_SET_POWER_LOW		0x0001
> +#define   SDHCI_UHS2_GEN_SET_N_LANES_POS	8
> +#define   SDHCI_UHS2_GEN_SET_2L_FD_HD		0x0
> +#define   SDHCI_UHS2_GEN_SET_2D1U_FD		0x2
> +#define   SDHCI_UHS2_GEN_SET_1D2U_FD		0x3
> +#define   SDHCI_UHS2_GEN_SET_2D2U_FD		0x4
> +
> +#define   SDHCI_UHS2_PHY_SET_SPEED_POS		6
> +#define   SDHCI_UHS2_PHY_SET_HIBER_EN		BIT(12)
> +#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK	GENMASK(19,16)
> +#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS	16
> +#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK	GENMASK(23,20)
> +#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS	20
> +
> +#define   SDHCI_UHS2_TRAN_SET_N_FCU_MASK	GENMASK(15,8)
> +#define   SDHCI_UHS2_TRAN_SET_N_FCU_POS		8
> +#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK	GENMASK(17,16)
> +#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS	16
> +
> +#define   SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK	GENMASK(7,0)
> +
> +#define SDHCI_UHS2_HOST_CAPS_PTR	0xE2
> +#define  SDHCI_UHS2_HOST_CAPS_GEN_OFFSET	0
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK	GENMASK(3,0)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK	GENMASK(7,4)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap)	((gap) * 360)
> +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK	GENMASK(13,8)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT	8
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD	1
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD	2
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD	4
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD	8
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64	BIT(14)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BOOT		BIT(15)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK	GENMASK(17,16)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT	16
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV	0
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB	1
> +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV	2
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK		GENMASK(21,18)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT	18
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK	GENMASK(23,22)
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT	22
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P		0
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING	1
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB		2
> +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING	3
> +
> +#define  SDHCI_UHS2_HOST_CAPS_PHY_OFFSET	4
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK		GENMASK(5,0)
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK		GENMASK(7,6)
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT		6
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A		0
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B		1
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK	GENMASK(19,16)
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT	16
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK	GENMASK(23,20)
> +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT	20
> +#define  SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET	8
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK	GENMASK(5,0)
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK		GENMASK(15,8)
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT		8
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK	GENMASK(18,16)
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT	16
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK	GENMASK(31,20)
> +#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT	20
> +
> +#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET	12
> +#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK	GENMASK(7,0)
> +
> +#define SDHCI_UHS2_TEST_PTR	0xE4
> +#define  SDHCI_UHS2_TEST_ERR_HEADER	BIT(0)
> +#define  SDHCI_UHS2_TEST_ERR_RES	BIT(1)
> +#define  SDHCI_UHS2_TEST_ERR_RETRY_EXP	BIT(2)
> +#define  SDHCI_UHS2_TEST_ERR_CRC	BIT(3)
> +#define  SDHCI_UHS2_TEST_ERR_FRAME	BIT(4)
> +#define  SDHCI_UHS2_TEST_ERR_TID	BIT(5)
> +#define  SDHCI_UHS2_TEST_ERR_UNRECOVER	BIT(7)
> +#define  SDHCI_UHS2_TEST_ERR_EBUSY	BIT(8)
> +#define  SDHCI_UHS2_TEST_ERR_ADMA	BIT(15)
> +#define  SDHCI_UHS2_TEST_ERR_RES_TIMEOUT	BIT(16)
> +#define  SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT	BIT(17)
> +#define  SDHCI_UHS2_TEST_ERR_VENDOR	BIT(27)
> +
> +#define SDHCI_UHS2_EMBED_CTRL	0xE6
> +#define SDHCI_UHS2_VENDOR	0xE8
> +
> +#endif /* __SDHCI_UHS2_H */
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index 0770c036e2ff..d9d7a76cedc1 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -43,8 +43,27 @@
>  #define  SDHCI_TRNS_READ	0x10
>  #define  SDHCI_TRNS_MULTI	0x20
>  
> +/*
> + * Defined in Host Version 4.10.
> + * 1 - R5 (SDIO)
> + * 0 - R1 (Memory)
> + */
> +#define  SDHCI_TRNS_RES_TYPE		0x40
> +#define  SDHCI_TRNS_RES_ERR_CHECK	0x80
> +#define  SDHCI_TRNS_RES_INT_DIS		0x0100
> +
>  #define SDHCI_COMMAND		0x0E
>  #define  SDHCI_CMD_RESP_MASK	0x03
> +
> +/*
> + * Host Version 4.10 adds this bit to distinguish a main command or
> + * sub command.
> + * CMD53(SDIO) - main command
> + * CMD52(SDIO) - sub command which doesn't have data block or doesn't
> + * indicate busy.
> + */
> +#define  SDHCI_CMD_SUB_CMD	0x04
> +
>  #define  SDHCI_CMD_CRC		0x08
>  #define  SDHCI_CMD_INDEX	0x10
>  #define  SDHCI_CMD_DATA		0x20
> @@ -60,11 +79,19 @@
>  
>  #define SDHCI_RESPONSE		0x10
>  
> +#define  SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET	0x10
> +#define  SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE	4
> +#define  SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET	0x18
> +#define  SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE	8

I would prefer to have all the UHS2 definitions in sdhci-uhs2.  If they
belong to an existing register, just put a comment saying what register.


> +
>  #define SDHCI_BUFFER		0x20
>  
>  #define SDHCI_PRESENT_STATE	0x24
>  #define  SDHCI_CMD_INHIBIT	0x00000001
>  #define  SDHCI_DATA_INHIBIT	0x00000002
> +
> +#define  SDHCI_DATA_HIGH_LVL_MASK	0x000000F0
> +
>  #define  SDHCI_DOING_WRITE	0x00000100
>  #define  SDHCI_DOING_READ	0x00000200
>  #define  SDHCI_SPACE_AVAILABLE	0x00000400
> @@ -80,6 +107,13 @@
>  #define   SDHCI_DATA_0_LVL_MASK	0x00100000
>  #define  SDHCI_CMD_LVL		0x01000000
>  
> +#define  SDHCI_HOST_REGULATOR_STABLE	0x02000000
> +#define  SDHCI_CMD_NOT_ISSUE_ERR	0x08000000
> +#define  SDHCI_SUB_CMD_STATUS		0x10000000
> +#define  SDHCI_UHS2_IN_DORMANT_STATE	0x20000000
> +#define  SDHCI_UHS2_LANE_SYNC		0x40000000
> +#define  SDHCI_UHS2_IF_DETECT		0x80000000
> +
>  #define SDHCI_HOST_CONTROL	0x28
>  #define  SDHCI_CTRL_LED		0x01
>  #define  SDHCI_CTRL_4BITBUS	0x02
> @@ -100,6 +134,11 @@
>  #define  SDHCI_POWER_300	0x0C
>  #define  SDHCI_POWER_330	0x0E
>  
> +/* VDD2 - UHS2 */
> +#define  SDHCI_VDD2_POWER_ON		0x10
> +#define  SDHCI_VDD2_POWER_180		0xA0
> +#define  SDHCI_VDD2_POWER_120		0x80
> +
>  #define SDHCI_BLOCK_GAP_CONTROL	0x2A
>  
>  #define SDHCI_WAKE_UP_CONTROL	0x2B
> @@ -110,7 +149,7 @@
>  #define SDHCI_CLOCK_CONTROL	0x2C
>  #define  SDHCI_DIVIDER_SHIFT	8
>  #define  SDHCI_DIVIDER_HI_SHIFT	6
> -#define  SDHCI_DIV_MASK	0xFF
> +#define  SDHCI_DIV_MASK		0xFF
>  #define  SDHCI_DIV_MASK_LEN	8
>  #define  SDHCI_DIV_HI_MASK	0x300
>  #define  SDHCI_PROG_CLOCK_MODE	0x0020
> @@ -139,6 +178,10 @@
>  #define  SDHCI_INT_CARD_REMOVE	0x00000080
>  #define  SDHCI_INT_CARD_INT	0x00000100
>  #define  SDHCI_INT_RETUNE	0x00001000
> +
> +/* Host Version 4.10 */
> +#define  SDHCI_INT_FX_EVENT	0x00002000
> +
>  #define  SDHCI_INT_CQE		0x00004000
>  #define  SDHCI_INT_ERROR	0x00008000
>  #define  SDHCI_INT_TIMEOUT	0x00010000
> @@ -152,6 +195,9 @@
>  #define  SDHCI_INT_AUTO_CMD_ERR	0x01000000
>  #define  SDHCI_INT_ADMA_ERROR	0x02000000
>  
> +/* Host Version 4.0 */
> +#define  SDHCI_INT_RESPONSE_ERROR	0x08000000
> +
>  #define  SDHCI_INT_NORMAL_MASK	0x00007FFF
>  #define  SDHCI_INT_ERROR_MASK	0xFFFF8000
>  
> @@ -178,6 +224,9 @@
>  #define  SDHCI_AUTO_CMD_END_BIT	0x00000008
>  #define  SDHCI_AUTO_CMD_INDEX	0x00000010
>  
> +/* Host Version 4.10 */
> +#define  SDHCI_ACMD_RESPONSE_ERROR	0x0020
> +
>  #define SDHCI_HOST_CONTROL2		0x3E
>  #define  SDHCI_CTRL_UHS_MASK		0x0007
>  #define   SDHCI_CTRL_UHS_SDR12		0x0000
> @@ -186,6 +235,7 @@
>  #define   SDHCI_CTRL_UHS_SDR104		0x0003
>  #define   SDHCI_CTRL_UHS_DDR50		0x0004
>  #define   SDHCI_CTRL_HS400		0x0005 /* Non-standard */
> +#define   SDHCI_CTRL_UHS_2		0x0007 /* UHS-2 */
>  #define  SDHCI_CTRL_VDD_180		0x0008
>  #define  SDHCI_CTRL_DRV_TYPE_MASK	0x0030
>  #define   SDHCI_CTRL_DRV_TYPE_B		0x0000
> @@ -194,9 +244,12 @@
>  #define   SDHCI_CTRL_DRV_TYPE_D		0x0030
>  #define  SDHCI_CTRL_EXEC_TUNING		0x0040
>  #define  SDHCI_CTRL_TUNED_CLK		0x0080
> +#define  SDHCI_CTRL_UHS2_INTERFACE_EN	0x0100 /* UHS-2 */
> +#define  SDHCI_CTRL_ADMA2_LEN_MODE	0x0400
>  #define  SDHCI_CMD23_ENABLE		0x0800
>  #define  SDHCI_CTRL_V4_MODE		0x1000
>  #define  SDHCI_CTRL_64BIT_ADDR		0x2000
> +#define  SDHCI_CTRL_ASYNC_INT_EN	0x4000
>  #define  SDHCI_CTRL_PRESET_VAL_ENABLE	0x8000
>  
>  #define SDHCI_CAPABILITIES	0x40
> @@ -217,11 +270,13 @@
>  #define  SDHCI_CAN_VDD_180	0x04000000
>  #define  SDHCI_CAN_64BIT_V4	0x08000000
>  #define  SDHCI_CAN_64BIT	0x10000000
> +#define  SDHCI_CAN_ASYNC_INT	0x20000000
>  
>  #define SDHCI_CAPABILITIES_1	0x44
>  #define  SDHCI_SUPPORT_SDR50	0x00000001
>  #define  SDHCI_SUPPORT_SDR104	0x00000002
>  #define  SDHCI_SUPPORT_DDR50	0x00000004
> +#define  SDHCI_SUPPORT_UHS2	0x00000008 /* UHS-2 support */
>  #define  SDHCI_DRIVER_TYPE_A	0x00000010
>  #define  SDHCI_DRIVER_TYPE_C	0x00000020
>  #define  SDHCI_DRIVER_TYPE_D	0x00000040
> @@ -230,19 +285,28 @@
>  #define  SDHCI_RETUNING_MODE_MASK		GENMASK(15, 14)
>  #define  SDHCI_CLOCK_MUL_MASK			GENMASK(23, 16)
>  #define  SDHCI_CAN_DO_ADMA3	0x08000000
> +#define  SDHCI_SUPPORT_VDD2_180	0x10000000 /* UHS-2 1.8V VDD2 */
> +#define  SDHCI_RSVD_FOR_VDD2    0x20000000 /* Rsvd for future VDD2 */
>  #define  SDHCI_SUPPORT_HS400	0x80000000 /* Non-standard */
>  
>  #define SDHCI_MAX_CURRENT		0x48
> +#define SDHCI_MAX_CURRENT_1		0x4C
>  #define  SDHCI_MAX_CURRENT_LIMIT	GENMASK(7, 0)
>  #define  SDHCI_MAX_CURRENT_330_MASK	GENMASK(7, 0)
>  #define  SDHCI_MAX_CURRENT_300_MASK	GENMASK(15, 8)
>  #define  SDHCI_MAX_CURRENT_180_MASK	GENMASK(23, 16)
> +#define  SDHCI_MAX_CURRENT_VDD2_180_MASK	GENMASK(7, 0) /* UHS2 */
>  #define   SDHCI_MAX_CURRENT_MULTIPLIER	4
>  
>  /* 4C-4F reserved for more max current */
>  
>  #define SDHCI_SET_ACMD12_ERROR	0x50
> +/* Host Version 4.10 */
> +#define SDHCI_SET_ACMD_RESPONSE_ERROR	0x20
>  #define SDHCI_SET_INT_ERROR	0x52
> +/* Host Version 4.10 */
> +#define SDHCI_SET_INT_TUNING_ERROR	0x0400
> +#define SDHCI_SET_INT_RESPONSE_ERROR	0x0800
>  
>  #define SDHCI_ADMA_ERROR	0x54
>  
> @@ -259,10 +323,16 @@
>  #define SDHCI_PRESET_FOR_SDR104        0x6C
>  #define SDHCI_PRESET_FOR_DDR50 0x6E
>  #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
> +
> +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */
> +/* UHS2 */
> +#define SDHCI_PRESET_FOR_UHS2  0x74
>  #define SDHCI_PRESET_DRV_MASK		GENMASK(15, 14)
>  #define SDHCI_PRESET_CLKGEN_SEL		BIT(10)
>  #define SDHCI_PRESET_SDCLK_FREQ_MASK	GENMASK(9, 0)
>  
> +#define SDHCI_ADMA3_ADDRESS	0x78
> +
>  #define SDHCI_SLOT_INT_STATUS	0xFC
>  
>  #define SDHCI_HOST_VERSION	0xFE
> @@ -652,6 +722,7 @@ struct sdhci_ops {
>  	void	(*request_done)(struct sdhci_host *host,
>  				struct mmc_request *mrq);
>  	void    (*dump_vendor_regs)(struct sdhci_host *host);
> +	void	(*dump_uhs2_regs)(struct sdhci_host *host);
>  };
>  
>  #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
>
AKASHI Takahiro Nov. 30, 2020, 5:21 a.m. UTC | #2
On Thu, Nov 26, 2020 at 10:15:29AM +0200, Adrian Hunter wrote:
> On 6/11/20 4:27 am, AKASHI Takahiro wrote:
> > Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.
> > 
> > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
> > ---
> >  drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++
> >  drivers/mmc/host/sdhci.h      |  73 +++++++++++-
> >  2 files changed, 282 insertions(+), 1 deletion(-)
> >  create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> > 
> > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> > new file mode 100644
> > index 000000000000..3b157df9c89c
> > --- /dev/null
> > +++ b/drivers/mmc/host/sdhci-uhs2.h
> > @@ -0,0 +1,210 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + *  linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
> > + *  Interface driver
> > + *
> > + * Header file for Host Controller UHS2 related registers and I/O accessors.
> > + *
> > + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> > + */
> > +#ifndef __SDHCI_UHS2_H
> > +#define __SDHCI_UHS2_H
> > +
> > +#include <linux/bits.h>
> > +
> > +/*
> > + * UHS-II Controller registers
> > + * 0x74 preset in sdhci.h
> > + * 0x80
> > + * 0x84-0xB4
> > + * 0xB8-0xCF
> > + * 0xE0-0xE7
> > + */
> > +/* UHS2 */
> > +#define SDHCI_UHS2_BLOCK_SIZE	0x80
> > +#define  SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \
> > +	((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
> > +
> > +#define SDHCI_UHS2_BLOCK_COUNT	0x84
> > +
> > +#define SDHCI_UHS2_CMD_PACKET	0x88
> > +#define  SDHCI_UHS2_CMD_PACK_MAX_LEN	20
> > +
> > +#define SDHCI_UHS2_TRANS_MODE	0x9C
> > +#define  SDHCI_UHS2_TRNS_DMA		BIT(0)
> > +#define  SDHCI_UHS2_TRNS_BLK_CNT_EN	BIT(1)
> > +#define  SDHCI_UHS2_TRNS_DATA_TRNS_WRT	BIT(4)
> > +#define  SDHCI_UHS2_TRNS_BLK_BYTE_MODE	BIT(5)
> > +#define  SDHCI_UHS2_TRNS_RES_R5		BIT(6)
> > +#define  SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN	BIT(7)
> > +#define  SDHCI_UHS2_TRNS_RES_INT_DIS	BIT(8)
> > +#define  SDHCI_UHS2_TRNS_WAIT_EBSY	BIT(14)
> > +#define  SDHCI_UHS2_TRNS_2L_HD		BIT(15)
> > +
> > +#define SDHCI_UHS2_COMMAND	0x9E
> > +#define  SDHCI_UHS2_COMMAND_SUB_CMD	0x0004
> > +#define  SDHCI_UHS2_COMMAND_DATA	0x0020
> > +#define  SDHCI_UHS2_COMMAND_TRNS_ABORT	0x0040
> > +#define  SDHCI_UHS2_COMMAND_CMD12	0x0080
> > +#define  SDHCI_UHS2_COMMAND_DORMANT	0x00C0
> > +#define  SDHCI_UHS2_COMMAND_PACK_LEN_MASK	GENMASK(12,8)
> > +#define  SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT	8
> > +
> > +#define SDHCI_UHS2_RESPONSE	0xA0
> > +#define  SDHCI_UHS2_RESPONSE_MAX_LEN	20
> > +
> > +#define SDHCI_UHS2_MSG_SELECT	0xB4
> > +#define SDHCI_UHS2_MSG_SELECT_CURR	0x0
> > +#define SDHCI_UHS2_MSG_SELECT_ONE	0x1
> > +#define SDHCI_UHS2_MSG_SELECT_TWO	0x2
> > +#define SDHCI_UHS2_MSG_SELECT_THREE	0x3
> > +
> > +#define SDHCI_UHS2_MSG		0xB8
> > +
> > +#define SDHCI_UHS2_DEV_INT_STATUS	0xBC
> > +
> > +#define SDHCI_UHS2_DEV_SELECT	0xBE
> > +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK	GENMASK(3,0)
> > +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN	BIT(7)
> > +
> > +#define SDHCI_UHS2_DEV_INT_CODE	0xBF
> > +
> > +#define SDHCI_UHS2_SW_RESET	0xC0
> > +#define SDHCI_UHS2_SW_RESET_FULL	0x0001
> > +#define SDHCI_UHS2_SW_RESET_SD		0x0002
> > +
> > +#define SDHCI_UHS2_TIMER_CTRL	0xC2
> > +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT	4
> > +
> > +#define SDHCI_UHS2_ERR_INT_STATUS		0xC4
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EN		0xC8
> > +#define SDHCI_UHS2_ERR_INT_SIG_EN		0xCC
> > +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER	BIT(0)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES		BIT(1)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP	BIT(2)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CRC		BIT(3)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME		BIT(4)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_TID		BIT(5)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER	BIT(7)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY		BIT(8)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA		BIT(15)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT	BIT(16)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT	BIT(17)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR	BIT(27)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_MASK	\
> > +		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK	\
> > +		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT)
> > +/* CRC Error occurs during a packet receiving */
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK	\
> > +		(SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
> > +		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
> > +		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +
> > +#define SDHCI_UHS2_SET_PTR	0xE0
> > +#define   SDHCI_UHS2_GEN_SET_POWER_LOW		0x0001
> > +#define   SDHCI_UHS2_GEN_SET_N_LANES_POS	8
> > +#define   SDHCI_UHS2_GEN_SET_2L_FD_HD		0x0
> > +#define   SDHCI_UHS2_GEN_SET_2D1U_FD		0x2
> > +#define   SDHCI_UHS2_GEN_SET_1D2U_FD		0x3
> > +#define   SDHCI_UHS2_GEN_SET_2D2U_FD		0x4
> > +
> > +#define   SDHCI_UHS2_PHY_SET_SPEED_POS		6
> > +#define   SDHCI_UHS2_PHY_SET_HIBER_EN		BIT(12)
> > +#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK	GENMASK(19,16)
> > +#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS	16
> > +#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK	GENMASK(23,20)
> > +#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS	20
> > +
> > +#define   SDHCI_UHS2_TRAN_SET_N_FCU_MASK	GENMASK(15,8)
> > +#define   SDHCI_UHS2_TRAN_SET_N_FCU_POS		8
> > +#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK	GENMASK(17,16)
> > +#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS	16
> > +
> > +#define   SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK	GENMASK(7,0)
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_PTR	0xE2
> > +#define  SDHCI_UHS2_HOST_CAPS_GEN_OFFSET	0
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK	GENMASK(3,0)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK	GENMASK(7,4)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap)	((gap) * 360)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK	GENMASK(13,8)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT	8
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD	1
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD	2
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD	4
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD	8
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64	BIT(14)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BOOT		BIT(15)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK	GENMASK(17,16)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT	16
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV	0
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB	1
> > +#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV	2
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK		GENMASK(21,18)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT	18
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK	GENMASK(23,22)
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT	22
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P		0
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING	1
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB		2
> > +#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING	3
> > +
> > +#define  SDHCI_UHS2_HOST_CAPS_PHY_OFFSET	4
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK		GENMASK(5,0)
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK		GENMASK(7,6)
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT		6
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A		0
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B		1
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK	GENMASK(19,16)
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT	16
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK	GENMASK(23,20)
> > +#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT	20
> > +#define  SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET	8
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK	GENMASK(5,0)
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK		GENMASK(15,8)
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT		8
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK	GENMASK(18,16)
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT	16
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK	GENMASK(31,20)
> > +#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT	20
> > +
> > +#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET	12
> > +#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK	GENMASK(7,0)
> > +
> > +#define SDHCI_UHS2_TEST_PTR	0xE4
> > +#define  SDHCI_UHS2_TEST_ERR_HEADER	BIT(0)
> > +#define  SDHCI_UHS2_TEST_ERR_RES	BIT(1)
> > +#define  SDHCI_UHS2_TEST_ERR_RETRY_EXP	BIT(2)
> > +#define  SDHCI_UHS2_TEST_ERR_CRC	BIT(3)
> > +#define  SDHCI_UHS2_TEST_ERR_FRAME	BIT(4)
> > +#define  SDHCI_UHS2_TEST_ERR_TID	BIT(5)
> > +#define  SDHCI_UHS2_TEST_ERR_UNRECOVER	BIT(7)
> > +#define  SDHCI_UHS2_TEST_ERR_EBUSY	BIT(8)
> > +#define  SDHCI_UHS2_TEST_ERR_ADMA	BIT(15)
> > +#define  SDHCI_UHS2_TEST_ERR_RES_TIMEOUT	BIT(16)
> > +#define  SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT	BIT(17)
> > +#define  SDHCI_UHS2_TEST_ERR_VENDOR	BIT(27)
> > +
> > +#define SDHCI_UHS2_EMBED_CTRL	0xE6
> > +#define SDHCI_UHS2_VENDOR	0xE8
> > +
> > +#endif /* __SDHCI_UHS2_H */
> > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> > index 0770c036e2ff..d9d7a76cedc1 100644
> > --- a/drivers/mmc/host/sdhci.h
> > +++ b/drivers/mmc/host/sdhci.h
> > @@ -43,8 +43,27 @@
> >  #define  SDHCI_TRNS_READ	0x10
> >  #define  SDHCI_TRNS_MULTI	0x20
> >  
> > +/*
> > + * Defined in Host Version 4.10.
> > + * 1 - R5 (SDIO)
> > + * 0 - R1 (Memory)
> > + */
> > +#define  SDHCI_TRNS_RES_TYPE		0x40
> > +#define  SDHCI_TRNS_RES_ERR_CHECK	0x80
> > +#define  SDHCI_TRNS_RES_INT_DIS		0x0100
> > +
> >  #define SDHCI_COMMAND		0x0E
> >  #define  SDHCI_CMD_RESP_MASK	0x03
> > +
> > +/*
> > + * Host Version 4.10 adds this bit to distinguish a main command or
> > + * sub command.
> > + * CMD53(SDIO) - main command
> > + * CMD52(SDIO) - sub command which doesn't have data block or doesn't
> > + * indicate busy.
> > + */
> > +#define  SDHCI_CMD_SUB_CMD	0x04
> > +
> >  #define  SDHCI_CMD_CRC		0x08
> >  #define  SDHCI_CMD_INDEX	0x10
> >  #define  SDHCI_CMD_DATA		0x20
> > @@ -60,11 +79,19 @@
> >  
> >  #define SDHCI_RESPONSE		0x10
> >  
> > +#define  SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET	0x10
> > +#define  SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE	4
> > +#define  SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET	0x18
> > +#define  SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE	8
> 
> I would prefer to have all the UHS2 definitions in sdhci-uhs2.  If they
> belong to an existing register, just put a comment saying what register.

I would disagree, but if you really want, I'd defer to you.

-Takahiro Akashi

> 
> > +
> >  #define SDHCI_BUFFER		0x20
> >  
> >  #define SDHCI_PRESENT_STATE	0x24
> >  #define  SDHCI_CMD_INHIBIT	0x00000001
> >  #define  SDHCI_DATA_INHIBIT	0x00000002
> > +
> > +#define  SDHCI_DATA_HIGH_LVL_MASK	0x000000F0
> > +
> >  #define  SDHCI_DOING_WRITE	0x00000100
> >  #define  SDHCI_DOING_READ	0x00000200
> >  #define  SDHCI_SPACE_AVAILABLE	0x00000400
> > @@ -80,6 +107,13 @@
> >  #define   SDHCI_DATA_0_LVL_MASK	0x00100000
> >  #define  SDHCI_CMD_LVL		0x01000000
> >  
> > +#define  SDHCI_HOST_REGULATOR_STABLE	0x02000000
> > +#define  SDHCI_CMD_NOT_ISSUE_ERR	0x08000000
> > +#define  SDHCI_SUB_CMD_STATUS		0x10000000
> > +#define  SDHCI_UHS2_IN_DORMANT_STATE	0x20000000
> > +#define  SDHCI_UHS2_LANE_SYNC		0x40000000
> > +#define  SDHCI_UHS2_IF_DETECT		0x80000000
> > +
> >  #define SDHCI_HOST_CONTROL	0x28
> >  #define  SDHCI_CTRL_LED		0x01
> >  #define  SDHCI_CTRL_4BITBUS	0x02
> > @@ -100,6 +134,11 @@
> >  #define  SDHCI_POWER_300	0x0C
> >  #define  SDHCI_POWER_330	0x0E
> >  
> > +/* VDD2 - UHS2 */
> > +#define  SDHCI_VDD2_POWER_ON		0x10
> > +#define  SDHCI_VDD2_POWER_180		0xA0
> > +#define  SDHCI_VDD2_POWER_120		0x80
> > +
> >  #define SDHCI_BLOCK_GAP_CONTROL	0x2A
> >  
> >  #define SDHCI_WAKE_UP_CONTROL	0x2B
> > @@ -110,7 +149,7 @@
> >  #define SDHCI_CLOCK_CONTROL	0x2C
> >  #define  SDHCI_DIVIDER_SHIFT	8
> >  #define  SDHCI_DIVIDER_HI_SHIFT	6
> > -#define  SDHCI_DIV_MASK	0xFF
> > +#define  SDHCI_DIV_MASK		0xFF
> >  #define  SDHCI_DIV_MASK_LEN	8
> >  #define  SDHCI_DIV_HI_MASK	0x300
> >  #define  SDHCI_PROG_CLOCK_MODE	0x0020
> > @@ -139,6 +178,10 @@
> >  #define  SDHCI_INT_CARD_REMOVE	0x00000080
> >  #define  SDHCI_INT_CARD_INT	0x00000100
> >  #define  SDHCI_INT_RETUNE	0x00001000
> > +
> > +/* Host Version 4.10 */
> > +#define  SDHCI_INT_FX_EVENT	0x00002000
> > +
> >  #define  SDHCI_INT_CQE		0x00004000
> >  #define  SDHCI_INT_ERROR	0x00008000
> >  #define  SDHCI_INT_TIMEOUT	0x00010000
> > @@ -152,6 +195,9 @@
> >  #define  SDHCI_INT_AUTO_CMD_ERR	0x01000000
> >  #define  SDHCI_INT_ADMA_ERROR	0x02000000
> >  
> > +/* Host Version 4.0 */
> > +#define  SDHCI_INT_RESPONSE_ERROR	0x08000000
> > +
> >  #define  SDHCI_INT_NORMAL_MASK	0x00007FFF
> >  #define  SDHCI_INT_ERROR_MASK	0xFFFF8000
> >  
> > @@ -178,6 +224,9 @@
> >  #define  SDHCI_AUTO_CMD_END_BIT	0x00000008
> >  #define  SDHCI_AUTO_CMD_INDEX	0x00000010
> >  
> > +/* Host Version 4.10 */
> > +#define  SDHCI_ACMD_RESPONSE_ERROR	0x0020
> > +
> >  #define SDHCI_HOST_CONTROL2		0x3E
> >  #define  SDHCI_CTRL_UHS_MASK		0x0007
> >  #define   SDHCI_CTRL_UHS_SDR12		0x0000
> > @@ -186,6 +235,7 @@
> >  #define   SDHCI_CTRL_UHS_SDR104		0x0003
> >  #define   SDHCI_CTRL_UHS_DDR50		0x0004
> >  #define   SDHCI_CTRL_HS400		0x0005 /* Non-standard */
> > +#define   SDHCI_CTRL_UHS_2		0x0007 /* UHS-2 */
> >  #define  SDHCI_CTRL_VDD_180		0x0008
> >  #define  SDHCI_CTRL_DRV_TYPE_MASK	0x0030
> >  #define   SDHCI_CTRL_DRV_TYPE_B		0x0000
> > @@ -194,9 +244,12 @@
> >  #define   SDHCI_CTRL_DRV_TYPE_D		0x0030
> >  #define  SDHCI_CTRL_EXEC_TUNING		0x0040
> >  #define  SDHCI_CTRL_TUNED_CLK		0x0080
> > +#define  SDHCI_CTRL_UHS2_INTERFACE_EN	0x0100 /* UHS-2 */
> > +#define  SDHCI_CTRL_ADMA2_LEN_MODE	0x0400
> >  #define  SDHCI_CMD23_ENABLE		0x0800
> >  #define  SDHCI_CTRL_V4_MODE		0x1000
> >  #define  SDHCI_CTRL_64BIT_ADDR		0x2000
> > +#define  SDHCI_CTRL_ASYNC_INT_EN	0x4000
> >  #define  SDHCI_CTRL_PRESET_VAL_ENABLE	0x8000
> >  
> >  #define SDHCI_CAPABILITIES	0x40
> > @@ -217,11 +270,13 @@
> >  #define  SDHCI_CAN_VDD_180	0x04000000
> >  #define  SDHCI_CAN_64BIT_V4	0x08000000
> >  #define  SDHCI_CAN_64BIT	0x10000000
> > +#define  SDHCI_CAN_ASYNC_INT	0x20000000
> >  
> >  #define SDHCI_CAPABILITIES_1	0x44
> >  #define  SDHCI_SUPPORT_SDR50	0x00000001
> >  #define  SDHCI_SUPPORT_SDR104	0x00000002
> >  #define  SDHCI_SUPPORT_DDR50	0x00000004
> > +#define  SDHCI_SUPPORT_UHS2	0x00000008 /* UHS-2 support */
> >  #define  SDHCI_DRIVER_TYPE_A	0x00000010
> >  #define  SDHCI_DRIVER_TYPE_C	0x00000020
> >  #define  SDHCI_DRIVER_TYPE_D	0x00000040
> > @@ -230,19 +285,28 @@
> >  #define  SDHCI_RETUNING_MODE_MASK		GENMASK(15, 14)
> >  #define  SDHCI_CLOCK_MUL_MASK			GENMASK(23, 16)
> >  #define  SDHCI_CAN_DO_ADMA3	0x08000000
> > +#define  SDHCI_SUPPORT_VDD2_180	0x10000000 /* UHS-2 1.8V VDD2 */
> > +#define  SDHCI_RSVD_FOR_VDD2    0x20000000 /* Rsvd for future VDD2 */
> >  #define  SDHCI_SUPPORT_HS400	0x80000000 /* Non-standard */
> >  
> >  #define SDHCI_MAX_CURRENT		0x48
> > +#define SDHCI_MAX_CURRENT_1		0x4C
> >  #define  SDHCI_MAX_CURRENT_LIMIT	GENMASK(7, 0)
> >  #define  SDHCI_MAX_CURRENT_330_MASK	GENMASK(7, 0)
> >  #define  SDHCI_MAX_CURRENT_300_MASK	GENMASK(15, 8)
> >  #define  SDHCI_MAX_CURRENT_180_MASK	GENMASK(23, 16)
> > +#define  SDHCI_MAX_CURRENT_VDD2_180_MASK	GENMASK(7, 0) /* UHS2 */
> >  #define   SDHCI_MAX_CURRENT_MULTIPLIER	4
> >  
> >  /* 4C-4F reserved for more max current */
> >  
> >  #define SDHCI_SET_ACMD12_ERROR	0x50
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_ACMD_RESPONSE_ERROR	0x20
> >  #define SDHCI_SET_INT_ERROR	0x52
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_INT_TUNING_ERROR	0x0400
> > +#define SDHCI_SET_INT_RESPONSE_ERROR	0x0800
> >  
> >  #define SDHCI_ADMA_ERROR	0x54
> >  
> > @@ -259,10 +323,16 @@
> >  #define SDHCI_PRESET_FOR_SDR104        0x6C
> >  #define SDHCI_PRESET_FOR_DDR50 0x6E
> >  #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
> > +
> > +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */
> > +/* UHS2 */
> > +#define SDHCI_PRESET_FOR_UHS2  0x74
> >  #define SDHCI_PRESET_DRV_MASK		GENMASK(15, 14)
> >  #define SDHCI_PRESET_CLKGEN_SEL		BIT(10)
> >  #define SDHCI_PRESET_SDCLK_FREQ_MASK	GENMASK(9, 0)
> >  
> > +#define SDHCI_ADMA3_ADDRESS	0x78
> > +
> >  #define SDHCI_SLOT_INT_STATUS	0xFC
> >  
> >  #define SDHCI_HOST_VERSION	0xFE
> > @@ -652,6 +722,7 @@ struct sdhci_ops {
> >  	void	(*request_done)(struct sdhci_host *host,
> >  				struct mmc_request *mrq);
> >  	void    (*dump_vendor_regs)(struct sdhci_host *host);
> > +	void	(*dump_uhs2_regs)(struct sdhci_host *host);
> >  };
> >  
> >  #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
> > 
>
diff mbox series

Patch

diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
new file mode 100644
index 000000000000..3b157df9c89c
--- /dev/null
+++ b/drivers/mmc/host/sdhci-uhs2.h
@@ -0,0 +1,210 @@ 
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
+ *  Interface driver
+ *
+ * Header file for Host Controller UHS2 related registers and I/O accessors.
+ *
+ *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
+ */
+#ifndef __SDHCI_UHS2_H
+#define __SDHCI_UHS2_H
+
+#include <linux/bits.h>
+
+/*
+ * UHS-II Controller registers
+ * 0x74 preset in sdhci.h
+ * 0x80
+ * 0x84-0xB4
+ * 0xB8-0xCF
+ * 0xE0-0xE7
+ */
+/* UHS2 */
+#define SDHCI_UHS2_BLOCK_SIZE	0x80
+#define  SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \
+	((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
+
+#define SDHCI_UHS2_BLOCK_COUNT	0x84
+
+#define SDHCI_UHS2_CMD_PACKET	0x88
+#define  SDHCI_UHS2_CMD_PACK_MAX_LEN	20
+
+#define SDHCI_UHS2_TRANS_MODE	0x9C
+#define  SDHCI_UHS2_TRNS_DMA		BIT(0)
+#define  SDHCI_UHS2_TRNS_BLK_CNT_EN	BIT(1)
+#define  SDHCI_UHS2_TRNS_DATA_TRNS_WRT	BIT(4)
+#define  SDHCI_UHS2_TRNS_BLK_BYTE_MODE	BIT(5)
+#define  SDHCI_UHS2_TRNS_RES_R5		BIT(6)
+#define  SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN	BIT(7)
+#define  SDHCI_UHS2_TRNS_RES_INT_DIS	BIT(8)
+#define  SDHCI_UHS2_TRNS_WAIT_EBSY	BIT(14)
+#define  SDHCI_UHS2_TRNS_2L_HD		BIT(15)
+
+#define SDHCI_UHS2_COMMAND	0x9E
+#define  SDHCI_UHS2_COMMAND_SUB_CMD	0x0004
+#define  SDHCI_UHS2_COMMAND_DATA	0x0020
+#define  SDHCI_UHS2_COMMAND_TRNS_ABORT	0x0040
+#define  SDHCI_UHS2_COMMAND_CMD12	0x0080
+#define  SDHCI_UHS2_COMMAND_DORMANT	0x00C0
+#define  SDHCI_UHS2_COMMAND_PACK_LEN_MASK	GENMASK(12,8)
+#define  SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT	8
+
+#define SDHCI_UHS2_RESPONSE	0xA0
+#define  SDHCI_UHS2_RESPONSE_MAX_LEN	20
+
+#define SDHCI_UHS2_MSG_SELECT	0xB4
+#define SDHCI_UHS2_MSG_SELECT_CURR	0x0
+#define SDHCI_UHS2_MSG_SELECT_ONE	0x1
+#define SDHCI_UHS2_MSG_SELECT_TWO	0x2
+#define SDHCI_UHS2_MSG_SELECT_THREE	0x3
+
+#define SDHCI_UHS2_MSG		0xB8
+
+#define SDHCI_UHS2_DEV_INT_STATUS	0xBC
+
+#define SDHCI_UHS2_DEV_SELECT	0xBE
+#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK	GENMASK(3,0)
+#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN	BIT(7)
+
+#define SDHCI_UHS2_DEV_INT_CODE	0xBF
+
+#define SDHCI_UHS2_SW_RESET	0xC0
+#define SDHCI_UHS2_SW_RESET_FULL	0x0001
+#define SDHCI_UHS2_SW_RESET_SD		0x0002
+
+#define SDHCI_UHS2_TIMER_CTRL	0xC2
+#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT	4
+
+#define SDHCI_UHS2_ERR_INT_STATUS		0xC4
+#define SDHCI_UHS2_ERR_INT_STATUS_EN		0xC8
+#define SDHCI_UHS2_ERR_INT_SIG_EN		0xCC
+#define SDHCI_UHS2_ERR_INT_STATUS_HEADER	BIT(0)
+#define SDHCI_UHS2_ERR_INT_STATUS_RES		BIT(1)
+#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP	BIT(2)
+#define SDHCI_UHS2_ERR_INT_STATUS_CRC		BIT(3)
+#define SDHCI_UHS2_ERR_INT_STATUS_FRAME		BIT(4)
+#define SDHCI_UHS2_ERR_INT_STATUS_TID		BIT(5)
+#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER	BIT(7)
+#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY		BIT(8)
+#define SDHCI_UHS2_ERR_INT_STATUS_ADMA		BIT(15)
+#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT	BIT(16)
+#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT	BIT(17)
+#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR	BIT(27)
+#define SDHCI_UHS2_ERR_INT_STATUS_MASK	\
+		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
+		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
+		SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
+		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
+		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
+		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
+		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
+		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
+		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
+		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT |	\
+		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
+#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK	\
+		(SDHCI_UHS2_ERR_INT_STATUS_HEADER |	\
+		SDHCI_UHS2_ERR_INT_STATUS_RES |		\
+		SDHCI_UHS2_ERR_INT_STATUS_FRAME |	\
+		SDHCI_UHS2_ERR_INT_STATUS_TID |		\
+		SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT)
+/* CRC Error occurs during a packet receiving */
+#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK	\
+		(SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP |	\
+		SDHCI_UHS2_ERR_INT_STATUS_CRC |		\
+		SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER |	\
+		SDHCI_UHS2_ERR_INT_STATUS_EBUSY |	\
+		SDHCI_UHS2_ERR_INT_STATUS_ADMA |	\
+		SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
+
+#define SDHCI_UHS2_SET_PTR	0xE0
+#define   SDHCI_UHS2_GEN_SET_POWER_LOW		0x0001
+#define   SDHCI_UHS2_GEN_SET_N_LANES_POS	8
+#define   SDHCI_UHS2_GEN_SET_2L_FD_HD		0x0
+#define   SDHCI_UHS2_GEN_SET_2D1U_FD		0x2
+#define   SDHCI_UHS2_GEN_SET_1D2U_FD		0x3
+#define   SDHCI_UHS2_GEN_SET_2D2U_FD		0x4
+
+#define   SDHCI_UHS2_PHY_SET_SPEED_POS		6
+#define   SDHCI_UHS2_PHY_SET_HIBER_EN		BIT(12)
+#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK	GENMASK(19,16)
+#define   SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS	16
+#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK	GENMASK(23,20)
+#define   SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS	20
+
+#define   SDHCI_UHS2_TRAN_SET_N_FCU_MASK	GENMASK(15,8)
+#define   SDHCI_UHS2_TRAN_SET_N_FCU_POS		8
+#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK	GENMASK(17,16)
+#define   SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS	16
+
+#define   SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK	GENMASK(7,0)
+
+#define SDHCI_UHS2_HOST_CAPS_PTR	0xE2
+#define  SDHCI_UHS2_HOST_CAPS_GEN_OFFSET	0
+#define   SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK	GENMASK(3,0)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK	GENMASK(7,4)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap)	((gap) * 360)
+#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4
+#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK	GENMASK(13,8)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT	8
+#define    SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD	1
+#define    SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD	2
+#define    SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD	4
+#define    SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD	8
+#define   SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64	BIT(14)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BOOT		BIT(15)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK	GENMASK(17,16)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT	16
+#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV	0
+#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB	1
+#define    SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV	2
+#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK		GENMASK(21,18)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT	18
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK	GENMASK(23,22)
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT	22
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P		0
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING	1
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB		2
+#define   SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING	3
+
+#define  SDHCI_UHS2_HOST_CAPS_PHY_OFFSET	4
+#define   SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK		GENMASK(5,0)
+#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK		GENMASK(7,6)
+#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT		6
+#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A		0
+#define   SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B		1
+#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK	GENMASK(19,16)
+#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT	16
+#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK	GENMASK(23,20)
+#define   SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT	20
+#define  SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET	8
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK	GENMASK(5,0)
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK		GENMASK(15,8)
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT		8
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK	GENMASK(18,16)
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT	16
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK	GENMASK(31,20)
+#define   SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT	20
+
+#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET	12
+#define  SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK	GENMASK(7,0)
+
+#define SDHCI_UHS2_TEST_PTR	0xE4
+#define  SDHCI_UHS2_TEST_ERR_HEADER	BIT(0)
+#define  SDHCI_UHS2_TEST_ERR_RES	BIT(1)
+#define  SDHCI_UHS2_TEST_ERR_RETRY_EXP	BIT(2)
+#define  SDHCI_UHS2_TEST_ERR_CRC	BIT(3)
+#define  SDHCI_UHS2_TEST_ERR_FRAME	BIT(4)
+#define  SDHCI_UHS2_TEST_ERR_TID	BIT(5)
+#define  SDHCI_UHS2_TEST_ERR_UNRECOVER	BIT(7)
+#define  SDHCI_UHS2_TEST_ERR_EBUSY	BIT(8)
+#define  SDHCI_UHS2_TEST_ERR_ADMA	BIT(15)
+#define  SDHCI_UHS2_TEST_ERR_RES_TIMEOUT	BIT(16)
+#define  SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT	BIT(17)
+#define  SDHCI_UHS2_TEST_ERR_VENDOR	BIT(27)
+
+#define SDHCI_UHS2_EMBED_CTRL	0xE6
+#define SDHCI_UHS2_VENDOR	0xE8
+
+#endif /* __SDHCI_UHS2_H */
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 0770c036e2ff..d9d7a76cedc1 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -43,8 +43,27 @@ 
 #define  SDHCI_TRNS_READ	0x10
 #define  SDHCI_TRNS_MULTI	0x20
 
+/*
+ * Defined in Host Version 4.10.
+ * 1 - R5 (SDIO)
+ * 0 - R1 (Memory)
+ */
+#define  SDHCI_TRNS_RES_TYPE		0x40
+#define  SDHCI_TRNS_RES_ERR_CHECK	0x80
+#define  SDHCI_TRNS_RES_INT_DIS		0x0100
+
 #define SDHCI_COMMAND		0x0E
 #define  SDHCI_CMD_RESP_MASK	0x03
+
+/*
+ * Host Version 4.10 adds this bit to distinguish a main command or
+ * sub command.
+ * CMD53(SDIO) - main command
+ * CMD52(SDIO) - sub command which doesn't have data block or doesn't
+ * indicate busy.
+ */
+#define  SDHCI_CMD_SUB_CMD	0x04
+
 #define  SDHCI_CMD_CRC		0x08
 #define  SDHCI_CMD_INDEX	0x10
 #define  SDHCI_CMD_DATA		0x20
@@ -60,11 +79,19 @@ 
 
 #define SDHCI_RESPONSE		0x10
 
+#define  SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET	0x10
+#define  SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE	4
+#define  SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET	0x18
+#define  SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE	8
+
 #define SDHCI_BUFFER		0x20
 
 #define SDHCI_PRESENT_STATE	0x24
 #define  SDHCI_CMD_INHIBIT	0x00000001
 #define  SDHCI_DATA_INHIBIT	0x00000002
+
+#define  SDHCI_DATA_HIGH_LVL_MASK	0x000000F0
+
 #define  SDHCI_DOING_WRITE	0x00000100
 #define  SDHCI_DOING_READ	0x00000200
 #define  SDHCI_SPACE_AVAILABLE	0x00000400
@@ -80,6 +107,13 @@ 
 #define   SDHCI_DATA_0_LVL_MASK	0x00100000
 #define  SDHCI_CMD_LVL		0x01000000
 
+#define  SDHCI_HOST_REGULATOR_STABLE	0x02000000
+#define  SDHCI_CMD_NOT_ISSUE_ERR	0x08000000
+#define  SDHCI_SUB_CMD_STATUS		0x10000000
+#define  SDHCI_UHS2_IN_DORMANT_STATE	0x20000000
+#define  SDHCI_UHS2_LANE_SYNC		0x40000000
+#define  SDHCI_UHS2_IF_DETECT		0x80000000
+
 #define SDHCI_HOST_CONTROL	0x28
 #define  SDHCI_CTRL_LED		0x01
 #define  SDHCI_CTRL_4BITBUS	0x02
@@ -100,6 +134,11 @@ 
 #define  SDHCI_POWER_300	0x0C
 #define  SDHCI_POWER_330	0x0E
 
+/* VDD2 - UHS2 */
+#define  SDHCI_VDD2_POWER_ON		0x10
+#define  SDHCI_VDD2_POWER_180		0xA0
+#define  SDHCI_VDD2_POWER_120		0x80
+
 #define SDHCI_BLOCK_GAP_CONTROL	0x2A
 
 #define SDHCI_WAKE_UP_CONTROL	0x2B
@@ -110,7 +149,7 @@ 
 #define SDHCI_CLOCK_CONTROL	0x2C
 #define  SDHCI_DIVIDER_SHIFT	8
 #define  SDHCI_DIVIDER_HI_SHIFT	6
-#define  SDHCI_DIV_MASK	0xFF
+#define  SDHCI_DIV_MASK		0xFF
 #define  SDHCI_DIV_MASK_LEN	8
 #define  SDHCI_DIV_HI_MASK	0x300
 #define  SDHCI_PROG_CLOCK_MODE	0x0020
@@ -139,6 +178,10 @@ 
 #define  SDHCI_INT_CARD_REMOVE	0x00000080
 #define  SDHCI_INT_CARD_INT	0x00000100
 #define  SDHCI_INT_RETUNE	0x00001000
+
+/* Host Version 4.10 */
+#define  SDHCI_INT_FX_EVENT	0x00002000
+
 #define  SDHCI_INT_CQE		0x00004000
 #define  SDHCI_INT_ERROR	0x00008000
 #define  SDHCI_INT_TIMEOUT	0x00010000
@@ -152,6 +195,9 @@ 
 #define  SDHCI_INT_AUTO_CMD_ERR	0x01000000
 #define  SDHCI_INT_ADMA_ERROR	0x02000000
 
+/* Host Version 4.0 */
+#define  SDHCI_INT_RESPONSE_ERROR	0x08000000
+
 #define  SDHCI_INT_NORMAL_MASK	0x00007FFF
 #define  SDHCI_INT_ERROR_MASK	0xFFFF8000
 
@@ -178,6 +224,9 @@ 
 #define  SDHCI_AUTO_CMD_END_BIT	0x00000008
 #define  SDHCI_AUTO_CMD_INDEX	0x00000010
 
+/* Host Version 4.10 */
+#define  SDHCI_ACMD_RESPONSE_ERROR	0x0020
+
 #define SDHCI_HOST_CONTROL2		0x3E
 #define  SDHCI_CTRL_UHS_MASK		0x0007
 #define   SDHCI_CTRL_UHS_SDR12		0x0000
@@ -186,6 +235,7 @@ 
 #define   SDHCI_CTRL_UHS_SDR104		0x0003
 #define   SDHCI_CTRL_UHS_DDR50		0x0004
 #define   SDHCI_CTRL_HS400		0x0005 /* Non-standard */
+#define   SDHCI_CTRL_UHS_2		0x0007 /* UHS-2 */
 #define  SDHCI_CTRL_VDD_180		0x0008
 #define  SDHCI_CTRL_DRV_TYPE_MASK	0x0030
 #define   SDHCI_CTRL_DRV_TYPE_B		0x0000
@@ -194,9 +244,12 @@ 
 #define   SDHCI_CTRL_DRV_TYPE_D		0x0030
 #define  SDHCI_CTRL_EXEC_TUNING		0x0040
 #define  SDHCI_CTRL_TUNED_CLK		0x0080
+#define  SDHCI_CTRL_UHS2_INTERFACE_EN	0x0100 /* UHS-2 */
+#define  SDHCI_CTRL_ADMA2_LEN_MODE	0x0400
 #define  SDHCI_CMD23_ENABLE		0x0800
 #define  SDHCI_CTRL_V4_MODE		0x1000
 #define  SDHCI_CTRL_64BIT_ADDR		0x2000
+#define  SDHCI_CTRL_ASYNC_INT_EN	0x4000
 #define  SDHCI_CTRL_PRESET_VAL_ENABLE	0x8000
 
 #define SDHCI_CAPABILITIES	0x40
@@ -217,11 +270,13 @@ 
 #define  SDHCI_CAN_VDD_180	0x04000000
 #define  SDHCI_CAN_64BIT_V4	0x08000000
 #define  SDHCI_CAN_64BIT	0x10000000
+#define  SDHCI_CAN_ASYNC_INT	0x20000000
 
 #define SDHCI_CAPABILITIES_1	0x44
 #define  SDHCI_SUPPORT_SDR50	0x00000001
 #define  SDHCI_SUPPORT_SDR104	0x00000002
 #define  SDHCI_SUPPORT_DDR50	0x00000004
+#define  SDHCI_SUPPORT_UHS2	0x00000008 /* UHS-2 support */
 #define  SDHCI_DRIVER_TYPE_A	0x00000010
 #define  SDHCI_DRIVER_TYPE_C	0x00000020
 #define  SDHCI_DRIVER_TYPE_D	0x00000040
@@ -230,19 +285,28 @@ 
 #define  SDHCI_RETUNING_MODE_MASK		GENMASK(15, 14)
 #define  SDHCI_CLOCK_MUL_MASK			GENMASK(23, 16)
 #define  SDHCI_CAN_DO_ADMA3	0x08000000
+#define  SDHCI_SUPPORT_VDD2_180	0x10000000 /* UHS-2 1.8V VDD2 */
+#define  SDHCI_RSVD_FOR_VDD2    0x20000000 /* Rsvd for future VDD2 */
 #define  SDHCI_SUPPORT_HS400	0x80000000 /* Non-standard */
 
 #define SDHCI_MAX_CURRENT		0x48
+#define SDHCI_MAX_CURRENT_1		0x4C
 #define  SDHCI_MAX_CURRENT_LIMIT	GENMASK(7, 0)
 #define  SDHCI_MAX_CURRENT_330_MASK	GENMASK(7, 0)
 #define  SDHCI_MAX_CURRENT_300_MASK	GENMASK(15, 8)
 #define  SDHCI_MAX_CURRENT_180_MASK	GENMASK(23, 16)
+#define  SDHCI_MAX_CURRENT_VDD2_180_MASK	GENMASK(7, 0) /* UHS2 */
 #define   SDHCI_MAX_CURRENT_MULTIPLIER	4
 
 /* 4C-4F reserved for more max current */
 
 #define SDHCI_SET_ACMD12_ERROR	0x50
+/* Host Version 4.10 */
+#define SDHCI_SET_ACMD_RESPONSE_ERROR	0x20
 #define SDHCI_SET_INT_ERROR	0x52
+/* Host Version 4.10 */
+#define SDHCI_SET_INT_TUNING_ERROR	0x0400
+#define SDHCI_SET_INT_RESPONSE_ERROR	0x0800
 
 #define SDHCI_ADMA_ERROR	0x54
 
@@ -259,10 +323,16 @@ 
 #define SDHCI_PRESET_FOR_SDR104        0x6C
 #define SDHCI_PRESET_FOR_DDR50 0x6E
 #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
+
+/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */
+/* UHS2 */
+#define SDHCI_PRESET_FOR_UHS2  0x74
 #define SDHCI_PRESET_DRV_MASK		GENMASK(15, 14)
 #define SDHCI_PRESET_CLKGEN_SEL		BIT(10)
 #define SDHCI_PRESET_SDCLK_FREQ_MASK	GENMASK(9, 0)
 
+#define SDHCI_ADMA3_ADDRESS	0x78
+
 #define SDHCI_SLOT_INT_STATUS	0xFC
 
 #define SDHCI_HOST_VERSION	0xFE
@@ -652,6 +722,7 @@  struct sdhci_ops {
 	void	(*request_done)(struct sdhci_host *host,
 				struct mmc_request *mrq);
 	void    (*dump_vendor_regs)(struct sdhci_host *host);
+	void	(*dump_uhs2_regs)(struct sdhci_host *host);
 };
 
 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS