@@ -1093,3 +1093,12 @@ config MMC_OWL
config MMC_SDHCI_EXTERNAL_DMA
bool
+
+config MMC_LITEX
+ tristate "LiteX MMC Host Controller support"
+ depends on OF
+ depends on PPC_MICROWATT || LITEX || COMPILE_TEST
+ help
+ This selects support for the MMC Host Controller found in LiteX SoCs.
+
+ If unsure, say N.
@@ -101,6 +101,7 @@ obj-$(CONFIG_MMC_CQHCI) += cqhci.o
cqhci-y += cqhci-core.o
cqhci-$(CONFIG_MMC_CRYPTO) += cqhci-crypto.o
obj-$(CONFIG_MMC_HSQ) += mmc_hsq.o
+obj-$(CONFIG_MMC_LITEX) += litex_mmc.o
ifeq ($(CONFIG_CB710_DEBUG),y)
CFLAGS-cb710-mmc += -DDEBUG
new file mode 100644
@@ -0,0 +1,644 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * LiteX LiteSDCard driver
+ *
+ * Copyright (C) 2019-2020 Antmicro <contact@antmicro.com>
+ * Copyright (C) 2019-2020 Kamil Rakoczy <krakoczy@antmicro.com>
+ * Copyright (C) 2019-2020 Maciej Dudek <mdudek@internships.antmicro.com>
+ * Copyright (C) 2020 Paul Mackerras <paulus@ozlabs.org>
+ * Copyright (C) 2020-2021 Gabriel Somlo <gsomlo@gmail.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/litex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/host.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+
+#define LITEX_PHY_CARDDETECT 0x00
+#define LITEX_PHY_CLOCKERDIV 0x04
+#define LITEX_PHY_INITIALIZE 0x08
+#define LITEX_PHY_WRITESTATUS 0x0C
+#define LITEX_CORE_CMDARG 0x00
+#define LITEX_CORE_CMDCMD 0x04
+#define LITEX_CORE_CMDSND 0x08
+#define LITEX_CORE_CMDRSP 0x0C
+#define LITEX_CORE_CMDEVT 0x1C
+#define LITEX_CORE_DATAEVT 0x20
+#define LITEX_CORE_BLKLEN 0x24
+#define LITEX_CORE_BLKCNT 0x28
+#define LITEX_BLK2MEM_BASE 0x00
+#define LITEX_BLK2MEM_LEN 0x08
+#define LITEX_BLK2MEM_ENA 0x0C
+#define LITEX_BLK2MEM_DONE 0x10
+#define LITEX_BLK2MEM_LOOP 0x14
+#define LITEX_MEM2BLK_BASE 0x00
+#define LITEX_MEM2BLK_LEN 0x08
+#define LITEX_MEM2BLK_ENA 0x0C
+#define LITEX_MEM2BLK_DONE 0x10
+#define LITEX_MEM2BLK_LOOP 0x14
+#define LITEX_MEM2BLK 0x18
+#define LITEX_IRQ_STATUS 0x00
+#define LITEX_IRQ_PENDING 0x04
+#define LITEX_IRQ_ENABLE 0x08
+
+#define SDCARD_CTRL_DATA_TRANSFER_NONE 0
+#define SDCARD_CTRL_DATA_TRANSFER_READ 1
+#define SDCARD_CTRL_DATA_TRANSFER_WRITE 2
+
+#define SDCARD_CTRL_RESPONSE_NONE 0
+#define SDCARD_CTRL_RESPONSE_SHORT 1
+#define SDCARD_CTRL_RESPONSE_LONG 2
+#define SDCARD_CTRL_RESPONSE_SHORT_BUSY 3
+
+#define SD_BIT_DONE BIT(0)
+#define SD_BIT_WR_ERR BIT(1)
+#define SD_BIT_TIMEOUT BIT(2)
+#define SD_BIT_CRC_ERR BIT(3)
+
+#define SD_SLEEP_US 5
+#define SD_TIMEOUT_US 20000
+
+#define SDIRQ_CARD_DETECT 1
+#define SDIRQ_SD_TO_MEM_DONE 2
+#define SDIRQ_MEM_TO_SD_DONE 4
+#define SDIRQ_CMD_DONE 8
+
+struct litex_mmc_host {
+ struct mmc_host *mmc;
+ struct platform_device *dev;
+
+ void __iomem *sdphy;
+ void __iomem *sdcore;
+ void __iomem *sdreader;
+ void __iomem *sdwriter;
+ void __iomem *sdirq;
+
+ void *buffer;
+ size_t buf_size;
+ dma_addr_t dma;
+
+ struct completion cmd_done;
+ int irq;
+
+ unsigned int ref_clk;
+ unsigned int sd_clk;
+ bool is_bus_width_set;
+ bool app_cmd;
+
+ u32 resp[4];
+ u16 rca;
+};
+
+static int litex_mmc_sdcard_wait_done(void __iomem *reg)
+{
+ u8 evt;
+ int ret;
+
+ ret = readx_poll_timeout(litex_read8, reg, evt, (evt & SD_BIT_DONE),
+ SD_SLEEP_US, SD_TIMEOUT_US);
+ if (ret || (evt & SD_BIT_TIMEOUT))
+ return -ETIMEDOUT;
+ if (evt == SD_BIT_DONE)
+ return 0;
+ if (evt & SD_BIT_WR_ERR)
+ return -EIO;
+ if (evt & SD_BIT_CRC_ERR)
+ return -EILSEQ;
+ pr_err("%s: unknown error evt=%x\n", __func__, evt);
+ return -EINVAL;
+}
+
+static int litex_mmc_send_cmd(struct litex_mmc_host *host,
+ u8 cmd, u32 arg, u8 response_len, u8 transfer)
+{
+ struct device *dev = mmc_dev(host->mmc);
+ void __iomem *reg;
+ int ret;
+ u8 evt;
+
+ litex_write32(host->sdcore + LITEX_CORE_CMDARG, arg);
+ litex_write32(host->sdcore + LITEX_CORE_CMDCMD,
+ cmd << 8 | transfer << 5 | response_len);
+ litex_write8(host->sdcore + LITEX_CORE_CMDSND, 1);
+
+ /* Wait for an interrupt if we have an interrupt and either there is
+ * data to be transferred, or if the card can report busy via DAT0.
+ */
+ if (host->irq > 0 &&
+ (transfer != SDCARD_CTRL_DATA_TRANSFER_NONE ||
+ response_len == SDCARD_CTRL_RESPONSE_SHORT_BUSY)) {
+ reinit_completion(&host->cmd_done);
+ litex_write32(host->sdirq + LITEX_IRQ_ENABLE,
+ SDIRQ_CMD_DONE | SDIRQ_CARD_DETECT);
+ wait_for_completion(&host->cmd_done);
+ }
+
+ ret = litex_mmc_sdcard_wait_done(host->sdcore + LITEX_CORE_CMDEVT);
+ if (ret) {
+ dev_err(dev, "Command (cmd %d) error, status %d\n", cmd, ret);
+ return ret;
+ }
+
+ if (response_len != SDCARD_CTRL_RESPONSE_NONE) {
+ int i;
+
+ reg = host->sdcore + LITEX_CORE_CMDRSP;
+ for (i = 0; i < 4; i++) {
+ host->resp[i] = litex_read32(reg);
+ reg += sizeof(u32);
+ }
+ }
+
+ if (!host->app_cmd && cmd == SD_SEND_RELATIVE_ADDR)
+ host->rca = (host->resp[3] >> 16) & 0xffff;
+
+ host->app_cmd = (cmd == MMC_APP_CMD);
+
+ if (transfer == SDCARD_CTRL_DATA_TRANSFER_NONE)
+ return ret; /* OK from prior litex_mmc_sdcard_wait_done() */
+
+ ret = litex_mmc_sdcard_wait_done(host->sdcore + LITEX_CORE_DATAEVT);
+ if (ret) {
+ dev_err(dev, "Data xfer (cmd %d) error, status %d\n", cmd, ret);
+ return ret;
+ }
+
+ /* wait for completion of (read or write) DMA transfer */
+ reg = (transfer == SDCARD_CTRL_DATA_TRANSFER_READ) ?
+ host->sdreader + LITEX_BLK2MEM_DONE :
+ host->sdwriter + LITEX_MEM2BLK_DONE;
+ ret = readx_poll_timeout(litex_read8, reg, evt, (evt & SD_BIT_DONE),
+ SD_SLEEP_US, SD_TIMEOUT_US);
+ if (ret)
+ dev_err(dev, "DMA timeout (cmd %d)\n", cmd);
+
+ return ret;
+}
+
+static int litex_mmc_send_app_cmd(struct litex_mmc_host *host)
+{
+ return litex_mmc_send_cmd(host, MMC_APP_CMD, host->rca << 16,
+ SDCARD_CTRL_RESPONSE_SHORT,
+ SDCARD_CTRL_DATA_TRANSFER_NONE);
+}
+
+static int litex_mmc_send_set_bus_w_cmd(struct litex_mmc_host *host, u32 width)
+{
+ return litex_mmc_send_cmd(host, SD_APP_SET_BUS_WIDTH, width,
+ SDCARD_CTRL_RESPONSE_SHORT,
+ SDCARD_CTRL_DATA_TRANSFER_NONE);
+}
+
+static int litex_mmc_set_bus_width(struct litex_mmc_host *host)
+{
+ bool app_cmd_sent = host->app_cmd; /* was preceding command app_cmd? */
+ int ret;
+
+ /* ensure 'app_cmd' precedes 'app_set_bus_width_cmd' */
+ if (!app_cmd_sent) {
+ ret = litex_mmc_send_app_cmd(host);
+ if (ret)
+ goto out;
+ }
+
+ /* litesdcard only supports 4-bit bus width */
+ ret = litex_mmc_send_set_bus_w_cmd(host, MMC_BUS_WIDTH_4);
+ if (ret)
+ goto out;
+
+ /* re-send 'app_cmd' if necessary */
+ if (app_cmd_sent)
+ ret = litex_mmc_send_app_cmd(host);
+
+out:
+ return ret;
+}
+
+static int litex_mmc_get_cd(struct mmc_host *mmc)
+{
+ struct litex_mmc_host *host = mmc_priv(mmc);
+ int ret;
+
+ if (!mmc_card_is_removable(mmc))
+ return 1;
+
+ ret = !litex_read8(host->sdphy + LITEX_PHY_CARDDETECT);
+
+ /* ensure bus width will be set (again) upon card (re)insertion */
+ if (ret == 0)
+ host->is_bus_width_set = false;
+
+ return ret;
+}
+
+static irqreturn_t litex_mmc_interrupt(int irq, void *arg)
+{
+ struct mmc_host *mmc = arg;
+ struct litex_mmc_host *host = mmc_priv(mmc);
+ u32 pending = litex_read32(host->sdirq + LITEX_IRQ_PENDING);
+
+ /* Check for card change interrupt */
+ if (pending & SDIRQ_CARD_DETECT) {
+ litex_write32(host->sdirq + LITEX_IRQ_PENDING,
+ SDIRQ_CARD_DETECT);
+ mmc_detect_change(mmc, msecs_to_jiffies(10));
+ }
+
+ /* Check for command completed */
+ if (pending & SDIRQ_CMD_DONE) {
+ /* Disable it so it doesn't keep interrupting */
+ litex_write32(host->sdirq + LITEX_IRQ_ENABLE,
+ SDIRQ_CARD_DETECT);
+ complete(&host->cmd_done);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static u32 litex_mmc_response_len(struct mmc_command *cmd)
+{
+ if (cmd->flags & MMC_RSP_136)
+ return SDCARD_CTRL_RESPONSE_LONG;
+ if (!(cmd->flags & MMC_RSP_PRESENT))
+ return SDCARD_CTRL_RESPONSE_NONE;
+ if (cmd->flags & MMC_RSP_BUSY)
+ return SDCARD_CTRL_RESPONSE_SHORT_BUSY;
+ return SDCARD_CTRL_RESPONSE_SHORT;
+}
+
+static void litex_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct litex_mmc_host *host = mmc_priv(mmc);
+ struct device *dev = mmc_dev(mmc);
+ struct mmc_command *cmd = mrq->cmd;
+ struct mmc_command *sbc = mrq->sbc;
+ struct mmc_data *data = mrq->data;
+ struct mmc_command *stop = mrq->stop;
+ unsigned int retries = cmd->retries;
+ unsigned int len = 0;
+ bool direct = false;
+ dma_addr_t dma;
+ int sg_count;
+
+ u32 response_len = litex_mmc_response_len(cmd);
+ u32 transfer = SDCARD_CTRL_DATA_TRANSFER_NONE;
+
+ /* First check that the card is still there */
+ if (!litex_mmc_get_cd(mmc)) {
+ cmd->error = -ENOMEDIUM;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+
+ /* Send set-block-count command if needed */
+ if (sbc) {
+ sbc->error = litex_mmc_send_cmd(host, sbc->opcode, sbc->arg,
+ litex_mmc_response_len(sbc),
+ SDCARD_CTRL_DATA_TRANSFER_NONE);
+ if (sbc->error) {
+ host->is_bus_width_set = false;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+ }
+
+ if (data) {
+ /* LiteSDCard only supports 4-bit bus width; therefore, we MUST
+ * inject a SET_BUS_WIDTH (acmd6) before the very first data
+ * transfer, earlier than when the mmc subsystem would normally
+ * get around to it!
+ */
+ if (!host->is_bus_width_set) {
+ cmd->error = litex_mmc_set_bus_width(host);
+ if (cmd->error) {
+ dev_err(dev, "Can't set bus width!\n");
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+ host->is_bus_width_set = true;
+ }
+
+ /* Try to DMA directly to/from the data buffer.
+ * We can do that if the buffer can be mapped for DMA
+ * in one contiguous chunk.
+ */
+ dma = host->dma;
+ len = data->blksz * data->blocks;
+ sg_count = dma_map_sg(dev, data->sg, data->sg_len,
+ mmc_get_dma_dir(data));
+ if (sg_count == 1) {
+ dma = sg_dma_address(data->sg);
+ len = sg_dma_len(data->sg);
+ direct = true;
+ } else if (len > host->buf_size)
+ len = host->buf_size;
+
+ if (data->flags & MMC_DATA_READ) {
+ litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 0);
+ litex_write64(host->sdreader + LITEX_BLK2MEM_BASE, dma);
+ litex_write32(host->sdreader + LITEX_BLK2MEM_LEN, len);
+ litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 1);
+
+ transfer = SDCARD_CTRL_DATA_TRANSFER_READ;
+ } else if (data->flags & MMC_DATA_WRITE) {
+ if (!direct)
+ sg_copy_to_buffer(data->sg, data->sg_len,
+ host->buffer, len);
+
+ litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 0);
+ litex_write64(host->sdwriter + LITEX_MEM2BLK_BASE, dma);
+ litex_write32(host->sdwriter + LITEX_MEM2BLK_LEN, len);
+ litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 1);
+
+ transfer = SDCARD_CTRL_DATA_TRANSFER_WRITE;
+ } else {
+ dev_warn(dev, "Data present w/o read or write flag.\n");
+ /* Continue: set cmd status, mark req done */
+ }
+
+ litex_write16(host->sdcore + LITEX_CORE_BLKLEN, data->blksz);
+ litex_write32(host->sdcore + LITEX_CORE_BLKCNT, data->blocks);
+ }
+
+ do {
+ cmd->error = litex_mmc_send_cmd(host, cmd->opcode, cmd->arg,
+ response_len, transfer);
+ } while (cmd->error && retries-- > 0);
+
+ if (cmd->error) {
+ /* card may be gone; don't assume bus width is still set */
+ host->is_bus_width_set = false;
+ }
+
+ if (response_len == SDCARD_CTRL_RESPONSE_SHORT) {
+ /* pull short response fields from appropriate host registers */
+ cmd->resp[0] = host->resp[3];
+ cmd->resp[1] = host->resp[2] & 0xFF;
+ } else if (response_len == SDCARD_CTRL_RESPONSE_LONG) {
+ cmd->resp[0] = host->resp[0];
+ cmd->resp[1] = host->resp[1];
+ cmd->resp[2] = host->resp[2];
+ cmd->resp[3] = host->resp[3];
+ }
+
+ /* Send stop-transmission command if required */
+ if (stop && (cmd->error || !sbc)) {
+ stop->error = litex_mmc_send_cmd(host, stop->opcode, stop->arg,
+ litex_mmc_response_len(stop),
+ SDCARD_CTRL_DATA_TRANSFER_NONE);
+ if (stop->error)
+ host->is_bus_width_set = false;
+ }
+
+ if (data) {
+ dma_unmap_sg(dev, data->sg, data->sg_len,
+ mmc_get_dma_dir(data));
+ }
+
+ if (!cmd->error && transfer != SDCARD_CTRL_DATA_TRANSFER_NONE) {
+ data->bytes_xfered = min(len, mmc->max_req_size);
+ if (transfer == SDCARD_CTRL_DATA_TRANSFER_READ && !direct) {
+ sg_copy_from_buffer(data->sg, sg_nents(data->sg),
+ host->buffer, data->bytes_xfered);
+ }
+ }
+
+ mmc_request_done(mmc, mrq);
+}
+
+static void litex_mmc_setclk(struct litex_mmc_host *host, unsigned int freq)
+{
+ struct device *dev = mmc_dev(host->mmc);
+ u32 div;
+
+ div = freq ? host->ref_clk / freq : 256U;
+ div = roundup_pow_of_two(div);
+ div = min(max(div, 2U), 256U);
+ dev_dbg(dev, "sd_clk_freq=%d: set to %d via div=%d\n",
+ freq, host->ref_clk / div, div);
+ litex_write16(host->sdphy + LITEX_PHY_CLOCKERDIV, div);
+ host->sd_clk = freq;
+}
+
+static void litex_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct litex_mmc_host *host = mmc_priv(mmc);
+
+ /* NOTE: Ignore any ios->bus_width updates; they occur right after
+ * the mmc core sends its own acmd6 bus-width change notification,
+ * which is redundant since we snoop on the command flow and inject
+ * an early acmd6 before the first data transfer command is sent!
+ */
+
+ /* update sd_clk */
+ if (ios->clock != host->sd_clk)
+ litex_mmc_setclk(host, ios->clock);
+}
+
+static const struct mmc_host_ops litex_mmc_ops = {
+ .get_cd = litex_mmc_get_cd,
+ .request = litex_mmc_request,
+ .set_ios = litex_mmc_set_ios,
+};
+
+static int litex_mmc_irq_init(struct litex_mmc_host *host)
+{
+ struct device *dev = mmc_dev(host->mmc);
+ int ret;
+
+ host->irq = platform_get_irq_optional(host->dev, 0);
+ if (host->irq <= 0) {
+ dev_warn(dev, "Failed to get IRQ, using polling\n");
+ goto use_polling;
+ }
+
+ host->sdirq = devm_platform_ioremap_resource_byname(host->dev, "irq");
+ if (IS_ERR(host->sdirq))
+ return PTR_ERR(host->sdirq);
+
+ ret = request_irq(host->irq, litex_mmc_interrupt, 0,
+ "litex-mmc", host->mmc);
+ if (ret < 0) {
+ dev_warn(dev, "IRQ request error %d, using polling\n", ret);
+ goto use_polling;
+ }
+
+ /* clear & enable card-change interrupts */
+ litex_write32(host->sdirq + LITEX_IRQ_PENDING, SDIRQ_CARD_DETECT);
+ litex_write32(host->sdirq + LITEX_IRQ_ENABLE, SDIRQ_CARD_DETECT);
+
+ return 0;
+
+use_polling:
+ host->mmc->caps |= MMC_CAP_NEEDS_POLL;
+ host->irq = 0;
+ return 0;
+}
+
+static int litex_mmc_probe(struct platform_device *pdev)
+{
+ struct litex_mmc_host *host;
+ struct mmc_host *mmc;
+ struct clk *clk;
+ int ret;
+
+ mmc = mmc_alloc_host(sizeof(struct litex_mmc_host), &pdev->dev);
+ /* NOTE: defaults to max_[req,seg]_size=PAGE_SIZE, max_blk_size=512,
+ * and max_blk_count accordingly set to 8;
+ * If for some reason we need to modify max_blk_count, we must also
+ * re-calculate `max_[req,seg]_size = max_blk_size * max_blk_count;`
+ */
+ if (!mmc)
+ return -ENOMEM;
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->dev = pdev;
+
+ /* initialize clock source */
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk)) {
+ ret = dev_err_probe(&pdev->dev,
+ PTR_ERR(clk), "can't get clock\n");
+ goto err;
+ }
+ host->ref_clk = clk_get_rate(clk);
+ host->sd_clk = 0;
+
+ /* LiteSDCard only supports 4-bit bus width; therefore, we MUST inject
+ * a SET_BUS_WIDTH (acmd6) before the very first data transfer, earlier
+ * than when the mmc subsystem would normally get around to it!
+ */
+ host->is_bus_width_set = false;
+ host->app_cmd = false;
+
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+ /* increase from default 32 on 64-bit-DMA capable architectures */
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+ if (ret)
+ goto err;
+#endif
+
+ host->buf_size = mmc->max_req_size * 2;
+ host->buffer = dmam_alloc_coherent(&pdev->dev, host->buf_size,
+ &host->dma, GFP_DMA);
+ if (host->buffer == NULL) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ host->sdphy = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(host->sdphy)) {
+ ret = PTR_ERR(host->sdphy);
+ goto err;
+ }
+
+ host->sdcore = devm_platform_ioremap_resource_byname(pdev, "core");
+ if (IS_ERR(host->sdcore)) {
+ ret = PTR_ERR(host->sdcore);
+ goto err;
+ }
+
+ host->sdreader = devm_platform_ioremap_resource_byname(pdev, "reader");
+ if (IS_ERR(host->sdreader)) {
+ ret = PTR_ERR(host->sdreader);
+ goto err;
+ }
+
+ host->sdwriter = devm_platform_ioremap_resource_byname(pdev, "writer");
+ if (IS_ERR(host->sdwriter)) {
+ ret = PTR_ERR(host->sdwriter);
+ goto err;
+ }
+
+ /* ensure DMA bus masters are disabled */
+ litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 0);
+ litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 0);
+
+ init_completion(&host->cmd_done);
+ ret = litex_mmc_irq_init(host);
+ if (ret)
+ goto err;
+
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+ mmc->ops = &litex_mmc_ops;
+
+ /* set default sd_clk frequency range based on empirical observations
+ * of LiteSDCard gateware behavior on typical SDCard media
+ */
+ mmc->f_min = 12.5e6;
+ mmc->f_max = 50e6;
+
+ ret = mmc_of_parse(mmc);
+ if (ret)
+ goto err;
+
+ /* force 4-bit bus_width (only width supported by hardware) */
+ mmc->caps &= ~MMC_CAP_8_BIT_DATA;
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+ /* set default capabilities */
+ mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY |
+ MMC_CAP_DRIVER_TYPE_D |
+ MMC_CAP_CMD23;
+ mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT |
+ MMC_CAP2_FULL_PWR_CYCLE |
+ MMC_CAP2_NO_SDIO;
+
+ platform_set_drvdata(pdev, host);
+
+ ret = mmc_add_host(mmc);
+ if (ret < 0)
+ goto err;
+
+ return 0;
+
+err:
+ mmc_free_host(mmc);
+ return ret;
+}
+
+static int litex_mmc_remove(struct platform_device *pdev)
+{
+ struct litex_mmc_host *host = dev_get_drvdata(&pdev->dev);
+
+ if (host->irq > 0)
+ free_irq(host->irq, host->mmc);
+ mmc_remove_host(host->mmc);
+ mmc_free_host(host->mmc);
+
+ return 0;
+}
+
+static const struct of_device_id litex_match[] = {
+ { .compatible = "litex,mmc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, litex_match);
+
+static struct platform_driver litex_mmc_driver = {
+ .probe = litex_mmc_probe,
+ .remove = litex_mmc_remove,
+ .driver = {
+ .name = "litex-mmc",
+ .of_match_table = of_match_ptr(litex_match),
+ },
+};
+module_platform_driver(litex_mmc_driver);
+
+MODULE_DESCRIPTION("LiteX SDCard driver");
+MODULE_AUTHOR("Antmicro <contact@antmicro.com>");
+MODULE_AUTHOR("Kamil Rakoczy <krakoczy@antmicro.com>");
+MODULE_AUTHOR("Maciej Dudek <mdudek@internships.antmicro.com>");
+MODULE_AUTHOR("Paul Mackerras <paulus@ozlabs.org>");
+MODULE_AUTHOR("Gabriel Somlo <gsomlo@gmail.com>");
+MODULE_LICENSE("GPL v2");