@@ -102,6 +102,7 @@ config MMC_SDHCI_PCI
tristate "SDHCI support on PCI bus"
depends on MMC_SDHCI && PCI
select MMC_CQHCI
+ select MMC_SDHCI_UHS2
select IOSF_MBI if X86
select MMC_SDHCI_IO_ACCESSORS
help
@@ -17,6 +17,7 @@
#include "sdhci.h"
#include "sdhci-pci.h"
#include "cqhci.h"
+#include "sdhci-uhs2.h"
/* Genesys Logic extra registers */
#define SDHCI_GLI_9750_WT 0x800
@@ -138,9 +139,36 @@
#define PCI_GLI_9755_PLLSSC 0x68
#define PCI_GLI_9755_PLLSSC_PPM GENMASK(15, 0)
+#define PCI_GLI_9755_PLLSSC_RTL BIT(24)
+#define GLI_9755_PLLSSC_RTL_VALUE 0x1
+#define PCI_GLI_9755_PLLSSC_TRANS_PASS BIT(27)
+#define GLI_9755_PLLSSC_TRANS_PASS_VALUE 0x1
+#define PCI_GLI_9755_PLLSSC_RECV GENMASK(29, 28)
+#define GLI_9755_PLLSSC_RECV_VALUE 0x3
+#define PCI_GLI_9755_PLLSSC_TRAN GENMASK(31, 30)
+#define GLI_9755_PLLSSC_TRAN_VALUE 0x3
+
+#define PCI_GLI_9755_UHS2_PLL 0x6C
+#define PCI_GLI_9755_UHS2_PLL_SSC GENMASK(9, 8)
+#define GLI_9755_UHS2_PLL_SSC_VALUE 0x0
+#define PCI_GLI_9755_UHS2_PLL_DELAY BIT(18)
+#define GLI_9755_UHS2_PLL_DELAY_VALUE 0x1
+#define PCI_GLI_9755_UHS2_PLL_PDRST BIT(27)
+#define GLI_9755_UHS2_PLL_PDRST_VALUE 0x1
#define PCI_GLI_9755_SerDes 0x70
+#define PCI_GLI_9755_UHS2_SERDES_INTR GENMASK(2, 0)
+#define GLI_9755_UHS2_SERDES_INTR_VALUE 0x3
+#define PCI_GLI_9755_UHS2_SERDES_ZC1 BIT(3)
+#define GLI_9755_UHS2_SERDES_ZC1_VALUE 0x0
+#define PCI_GLI_9755_UHS2_SERDES_ZC2 GENMASK(7, 4)
+#define GLI_9755_UHS2_SERDES_ZC2_DEFAULT 0xB
+#define GLI_9755_UHS2_SERDES_ZC2_SANDISK 0x0
#define PCI_GLI_9755_SCP_DIS BIT(19)
+#define PCI_GLI_9755_UHS2_SERDES_TRAN GENMASK(27, 24)
+#define GLI_9755_UHS2_SERDES_TRAN_VALUE 0xC
+#define PCI_GLI_9755_UHS2_SERDES_RECV GENMASK(31, 28)
+#define GLI_9755_UHS2_SERDES_RECV_VALUE 0xF
#define PCI_GLI_9755_MISC 0x78
#define PCI_GLI_9755_MISC_SSC_OFF BIT(26)
@@ -692,6 +720,276 @@ static void gl9755_hw_setting(struct sdhci_pci_slot *slot)
gl9755_wt_off(pdev);
}
+static void gl9755_vendor_init(struct sdhci_host *host)
+{
+ struct sdhci_pci_slot *slot = sdhci_priv(host);
+ struct pci_dev *pdev = slot->chip->pdev;
+ u32 serdes;
+ u32 pllssc;
+ u32 uhs2_pll;
+
+ gl9755_wt_on(pdev);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_SerDes, &serdes);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_TRAN;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_TRAN,
+ GLI_9755_UHS2_SERDES_TRAN_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_RECV;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_RECV,
+ GLI_9755_UHS2_SERDES_RECV_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_INTR;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_INTR,
+ GLI_9755_UHS2_SERDES_INTR_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC1;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC1,
+ GLI_9755_UHS2_SERDES_ZC1_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC2;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2,
+ GLI_9755_UHS2_SERDES_ZC2_DEFAULT);
+ pci_write_config_dword(pdev, PCI_GLI_9755_SerDes, serdes);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, &uhs2_pll);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_SSC;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_SSC,
+ GLI_9755_UHS2_PLL_SSC_VALUE);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_DELAY;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_DELAY,
+ GLI_9755_UHS2_PLL_DELAY_VALUE);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_PDRST;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_PDRST,
+ GLI_9755_UHS2_PLL_PDRST_VALUE);
+ pci_write_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, uhs2_pll);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_PLLSSC, &pllssc);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_RTL;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RTL,
+ GLI_9755_PLLSSC_RTL_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_TRANS_PASS;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRANS_PASS,
+ GLI_9755_PLLSSC_TRANS_PASS_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_RECV;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RECV,
+ GLI_9755_PLLSSC_RECV_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_TRAN;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRAN,
+ GLI_9755_PLLSSC_TRAN_VALUE);
+ pci_write_config_dword(pdev, PCI_GLI_9755_PLLSSC, pllssc);
+
+ gl9755_wt_off(pdev);
+}
+
+static void gl9755_pre_detect_init(struct sdhci_host *host)
+{
+ /* GL9755 need more time on UHS2 detect flow */
+ sdhci_writeb(host, 0xA7, SDHCI_UHS2_TIMER_CTRL);
+}
+
+static void gl9755_post_attach_sd(struct sdhci_host *host)
+{
+ struct pci_dev *pdev;
+ struct sdhci_pci_chip *chip;
+ struct sdhci_pci_slot *slot;
+ u32 serdes;
+
+ slot = sdhci_priv(host);
+ chip = slot->chip;
+ pdev = chip->pdev;
+
+ gl9755_wt_on(pdev);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_SerDes, &serdes);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC1;
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC2;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC1,
+ GLI_9755_UHS2_SERDES_ZC1_VALUE);
+
+ /* the manfid of sandisk card is 0x3 */
+ if (host->mmc->card->cid.manfid == 0x3)
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2,
+ GLI_9755_UHS2_SERDES_ZC2_SANDISK);
+ else
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2,
+ GLI_9755_UHS2_SERDES_ZC2_DEFAULT);
+
+ pci_write_config_dword(pdev, PCI_GLI_9755_SerDes, serdes);
+
+ gl9755_wt_off(pdev);
+}
+
+static void gl9755_overcurrent_event_enable(struct sdhci_host *host,
+ bool enable)
+{
+ u32 mask;
+
+ mask = sdhci_readl(host, SDHCI_SIGNAL_ENABLE);
+ if (enable)
+ mask |= SDHCI_INT_BUS_POWER;
+ else
+ mask &= ~SDHCI_INT_BUS_POWER;
+
+ sdhci_writel(host, mask, SDHCI_SIGNAL_ENABLE);
+
+ mask = sdhci_readl(host, SDHCI_INT_ENABLE);
+ if (enable)
+ mask |= SDHCI_INT_BUS_POWER;
+ else
+ mask &= ~SDHCI_INT_BUS_POWER;
+
+ sdhci_writel(host, mask, SDHCI_INT_ENABLE);
+}
+
+static void gl9755_set_power(struct sdhci_host *host, unsigned char mode,
+ unsigned short vdd)
+{
+ u8 pwr = 0;
+
+ if (mode != MMC_POWER_OFF) {
+ switch (1 << vdd) {
+ case MMC_VDD_165_195:
+ /*
+ * Without a regulator, SDHCI does not support 2.0v
+ * so we only get here if the driver deliberately
+ * added the 2.0v range to ocr_avail. Map it to 1.8v
+ * for the purpose of turning on the power.
+ */
+ case MMC_VDD_20_21:
+ pwr = SDHCI_POWER_180;
+ break;
+ case MMC_VDD_29_30:
+ case MMC_VDD_30_31:
+ pwr = SDHCI_POWER_300;
+ break;
+ case MMC_VDD_32_33:
+ case MMC_VDD_33_34:
+ pwr = SDHCI_POWER_330;
+ break;
+ default:
+ WARN(1, "%s: Invalid vdd %#x\n",
+ mmc_hostname(host->mmc), vdd);
+ break;
+ }
+
+ pwr |= SDHCI_VDD2_POWER_180;
+ }
+
+ if (host->pwr == pwr)
+ return;
+
+ host->pwr = pwr;
+
+ if (pwr == 0) {
+ gl9755_overcurrent_event_enable(host, false);
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+ } else {
+ gl9755_overcurrent_event_enable(host, false);
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+
+ pwr |= (SDHCI_POWER_ON | SDHCI_VDD2_POWER_ON);
+
+ sdhci_writeb(host, pwr & 0xf, SDHCI_POWER_CONTROL);
+ /* wait stable */
+ mdelay(5);
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+ /* wait stable */
+ mdelay(5);
+ gl9755_overcurrent_event_enable(host, true);
+ }
+}
+
+static bool sdhci_wait_clock_stable(struct sdhci_host *host)
+{
+ u16 clk = 0;
+ ktime_t timeout;
+
+ /* Wait max 20 ms */
+ timeout = ktime_add_ms(ktime_get(), 20);
+ while (1) {
+ bool timedout = ktime_after(ktime_get(), timeout);
+
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ if (clk & SDHCI_CLOCK_INT_STABLE)
+ break;
+ if (timedout) {
+ pr_err("%s: Internal clock never stabilised.\n",
+ mmc_hostname(host->mmc));
+ sdhci_dumpregs(host);
+ return false;
+ }
+ udelay(10);
+ }
+ return true;
+}
+
+static void gl9755_uhs2_reset_sd_tran(struct sdhci_host *host)
+{
+ /* do this on UHS2 mode */
+ if (host->mmc->flags & MMC_UHS2_INITIALIZED) {
+ sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_SD);
+ sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
+ sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
+ sdhci_uhs2_clear_set_irqs(host,
+ SDHCI_INT_ALL_MASK,
+ SDHCI_UHS2_ERR_INT_STATUS_MASK);
+ }
+}
+
+static void sdhci_gl9755_reset(struct sdhci_host *host, u8 mask)
+{
+ ktime_t timeout;
+ u16 ctrl2;
+ u16 clk_ctrl;
+
+ /* need internal clock */
+ if (mask & SDHCI_RESET_ALL) {
+ ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ clk_ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+
+ if ((ctrl2 & SDHCI_CTRL_V4_MODE) &&
+ (ctrl2 & SDHCI_CTRL_UHS2_INTERFACE_EN)) {
+ sdhci_writew(host,
+ SDHCI_CLOCK_INT_EN,
+ SDHCI_CLOCK_CONTROL);
+ } else {
+ sdhci_writew(host,
+ SDHCI_CLOCK_INT_EN,
+ SDHCI_CLOCK_CONTROL);
+ sdhci_wait_clock_stable(host);
+ sdhci_writew(host,
+ SDHCI_CTRL_V4_MODE,
+ SDHCI_HOST_CONTROL2);
+ }
+ }
+
+ sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
+
+ /* reset sd-tran on UHS2 mode if need to reset cmd/data */
+ if ((mask & SDHCI_RESET_CMD) | (mask & SDHCI_RESET_DATA))
+ gl9755_uhs2_reset_sd_tran(host);
+
+ if (mask & SDHCI_RESET_ALL)
+ host->clock = 0;
+
+ /* Wait max 100 ms */
+ timeout = ktime_add_ms(ktime_get(), 100);
+
+ /* hw clears the bit when it's done */
+ while (1) {
+ bool timedout = ktime_after(ktime_get(), timeout);
+
+ if (!(sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask))
+ break;
+ if (timedout) {
+ pr_err("%s: Reset 0x%x never completed.\n",
+ mmc_hostname(host->mmc), (int)mask);
+ sdhci_dumpregs(host);
+ /* manual clear */
+ sdhci_writeb(host, 0, SDHCI_SOFTWARE_RESET);
+ return;
+ }
+ udelay(10);
+ }
+}
+
static int gli_probe_slot_gl9750(struct sdhci_pci_slot *slot)
{
struct sdhci_host *host = slot->host;
@@ -700,6 +998,7 @@ static int gli_probe_slot_gl9750(struct sdhci_pci_slot *slot)
gli_pcie_enable_msi(slot);
slot->host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
sdhci_enable_v4_mode(host);
+ gl9755_vendor_init(host);
return 0;
}
@@ -1092,18 +1391,26 @@ static const struct sdhci_ops sdhci_gl9755_ops = {
.read_w = sdhci_gli_readw,
.read_b = sdhci_gli_readb,
.set_clock = sdhci_gl9755_set_clock,
+ .set_power = gl9755_set_power,
.enable_dma = sdhci_pci_enable_dma,
.set_bus_width = sdhci_set_bus_width,
- .reset = sdhci_reset,
+ .reset = sdhci_gl9755_reset,
.set_uhs_signaling = sdhci_set_uhs_signaling,
.voltage_switch = sdhci_gli_voltage_switch,
.uhs2_reset = sdhci_uhs2_reset,
+ .dump_uhs2_regs = sdhci_uhs2_dump_regs,
+ .set_timeout = sdhci_uhs2_set_timeout,
+ .irq = sdhci_uhs2_irq,
+ .uhs2_pre_detect_init = gl9755_pre_detect_init,
+ .uhs2_post_attach_sd = gl9755_post_attach_sd,
};
const struct sdhci_pci_fixes sdhci_gl9755 = {
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_BROKEN_DDR50,
.probe_slot = gli_probe_slot_gl9755,
+ .add_host = sdhci_pci_uhs2_add_host,
+ .remove_host = sdhci_pci_uhs2_remove_host,
.ops = &sdhci_gl9755_ops,
#ifdef CONFIG_PM_SLEEP
.resume = sdhci_pci_gli_resume,