| Message ID | 20221116193940.67445-1-blarson@amd.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | None | expand |
On Wed, Nov 16, 2022 at 11:39:40AM -0800, Brad Larson wrote: > Add support for the AMD Pensando Elba SoC System Resource chip > using the SPI interface. > > Signed-off-by: Brad Larson <blarson@amd.com> > --- > > v8: > - Apply review request changes and picked the two unique examples > for the 4 chip-selects as one has the reset control support and > the other an interrupt. Missed the --in-reply-to in git > send-email for v7, included in this update. No, you haven't. By default in git, you don't have to do anything. See --thread and --no-chain-reply-to options. If you are messing with --in-reply-to, you are doing it wrong. Please resend the whole series properly threaded. > > v7: > - Use system-controller for the device with four chip-selects > connected over spi. > - Delete child by moving reset-controller into the parent. > - Updated and used dtschema-2022.11 and yamllint-1.28.0 > > v6: > - Expand description, rename nodes and change compatible usage > > v5: > - Change to AMD Pensando instead of Pensando > > v4: > - Change Maintained to Supported > > .../bindings/mfd/amd,pensando-elbasr.yaml | 60 +++++++++++++++++++ > 1 file changed, 60 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > > diff --git a/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > new file mode 100644 > index 000000000000..622c93402a86 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > @@ -0,0 +1,60 @@ > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mfd/amd,pensando-elbasr.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: AMD Pensando Elba SoC Resource Controller > + > +description: | > + AMD Pensando Elba SoC Resource Controller functions are > + accessed with four chip-selects. Reset control is on CS0. One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' Hard to say more because I don't have the whole thread nor remember what exactly we discussed before. That was 100s of bindings ago... > + > +maintainers: > + - Brad Larson <blarson@amd.com> > + > +properties: > + compatible: > + enum: > + - amd,pensando-elbasr > + > + "#reset-cells": > + const: 1 > + > + interrupts: > + maxItems: 1 > + > +required: > + - compatible > + - reg > + - spi-max-frequency > + > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + > + spi { > + #address-cells = <1>; > + #size-cells = <0>; > + num-cs = <4>; > + > + system-controller@0 { > + compatible = "amd,pensando-elbasr"; > + reg = <0>; > + spi-max-frequency = <12000000>; > + #reset-cells = <1>; > + }; > + > + system-controller@2 { > + compatible = "amd,pensando-elbasr"; > + reg = <2>; > + spi-max-frequency = <12000000>; > + interrupt-parent = <&porta>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + }; > + }; > -- > 2.17.1 > >
[AMD Official Use Only - General] From: Rob Herring <robh@kernel.org> Sent: Wednesday, November 16, 2022 2:30 PM >> v8: >> - Apply review request changes and picked the two unique examples >> for the 4 chip-selects as one has the reset control support and >> the other an interrupt. Missed the --in-reply-to in git >> send-email for v7, included in this update. > >No, you haven't. By default in git, you don't have to do anything. See >--thread and --no-chain-reply-to options. If you are messing with >--in-reply-to, you are doing it wrong. > >Please resend the whole series properly threaded. Will resend the series >> diff --git a/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml >> new file mode 100644 >> index 000000000000..622c93402a86 >> --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml >> @@ -0,0 +1,60 @@ ... >> + >> +title: AMD Pensando Elba SoC Resource Controller >> + >> +description: | >> + AMD Pensando Elba SoC Resource Controller functions are >> + accessed with four chip-selects. Reset control is on CS0. > > One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' > > Hard to say more because I don't have the whole thread nor remember what > exactly we discussed before. That was 100s of bindings ago... I agree and the example for v7 had all 4 chip-selects shown. This is not a pick and choose device on what functions to use for a usable system. Krzysztof requested only showing two chip-selects in the example. ... >> +examples: >> + - | >> + #include <dt-bindings/interrupt-controller/arm-gic.h> >> + >> + spi { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + num-cs = <4>; >> + >> + system-controller@0 { >> + compatible = "amd,pensando-elbasr"; >> + reg = <0>; >> + spi-max-frequency = <12000000>; >> + #reset-cells = <1>; >> + }; >> + >> + system-controller@2 { >> + compatible = "amd,pensando-elbasr"; >> + reg = <2>; >> + spi-max-frequency = <12000000>; >> + interrupt-parent = <&porta>; >> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; >> + }; >> + }; Regards, Brad
On 17/11/2022 01:41, Larson, Bradley wrote: > [AMD Official Use Only - General] > > From: Rob Herring <robh@kernel.org> > Sent: Wednesday, November 16, 2022 2:30 PM > >>> v8: >>> - Apply review request changes and picked the two unique examples >>> for the 4 chip-selects as one has the reset control support and >>> the other an interrupt. Missed the --in-reply-to in git >>> send-email for v7, included in this update. >> >> No, you haven't. By default in git, you don't have to do anything. See >> --thread and --no-chain-reply-to options. If you are messing with >> --in-reply-to, you are doing it wrong. >> >> Please resend the whole series properly threaded. > > Will resend the series > >>> diff --git a/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml >>> new file mode 100644 >>> index 000000000000..622c93402a86 >>> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml >>> @@ -0,0 +1,60 @@ > ... >>> + >>> +title: AMD Pensando Elba SoC Resource Controller >>> + >>> +description: | >>> + AMD Pensando Elba SoC Resource Controller functions are >>> + accessed with four chip-selects. Reset control is on CS0. >> >> One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' >> >> Hard to say more because I don't have the whole thread nor remember what >> exactly we discussed before. That was 100s of bindings ago... > > I agree and the example for v7 had all 4 chip-selects shown. This is not a pick and > choose device on what functions to use for a usable system. Krzysztof requested > only showing two chip-selects in the example. The problem is that you describe here SPI controller (and its chip selects) but binding is for the SPI device. The example is not the problem... > ... >>> +examples: >>> + - | >>> + #include <dt-bindings/interrupt-controller/arm-gic.h> >>> + >>> + spi { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + num-cs = <4>; Drop this property as well, unless it is necessary to explain "amd,pensando-elbasr" device. >>> + >>> + system-controller@0 { >>> + compatible = "amd,pensando-elbasr"; >>> + reg = <0>; >>> + spi-max-frequency = <12000000>; >>> + #reset-cells = <1>; >>> + }; Best regards, Krzysztof
On Wed, Nov 16, 2022 at 6:41 PM Larson, Bradley <Bradley.Larson@amd.com> wrote: > > [AMD Official Use Only - General] > > From: Rob Herring <robh@kernel.org> > Sent: Wednesday, November 16, 2022 2:30 PM > > >> v8: > >> - Apply review request changes and picked the two unique examples > >> for the 4 chip-selects as one has the reset control support and > >> the other an interrupt. Missed the --in-reply-to in git > >> send-email for v7, included in this update. > > > >No, you haven't. By default in git, you don't have to do anything. See > >--thread and --no-chain-reply-to options. If you are messing with > >--in-reply-to, you are doing it wrong. > > > >Please resend the whole series properly threaded. > > Will resend the series > > >> diff --git a/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > >> new file mode 100644 > >> index 000000000000..622c93402a86 > >> --- /dev/null > > +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > >> @@ -0,0 +1,60 @@ > ... > >> + > >> +title: AMD Pensando Elba SoC Resource Controller > >> + > >> +description: | > >> + AMD Pensando Elba SoC Resource Controller functions are > >> + accessed with four chip-selects. Reset control is on CS0. > > > > One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' > > > > Hard to say more because I don't have the whole thread nor remember what > > exactly we discussed before. That was 100s of bindings ago... > > I agree and the example for v7 had all 4 chip-selects shown. That is not what I said. Look at 'reg' above again. You have 1 device, but you have 4 nodes which looks like separate 4 devices. The exception would be if what's on each chip select is independent from each other. Describe what your h/w has/is/does so we can provide better guidance. Rob
[AMD Official Use Only - General] Hi Rob and Krzysztof, > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > > ... > > > > + > > > > +title: AMD Pensando Elba SoC Resource Controller > > > > + > > > > +description: | > > > > + AMD Pensando Elba SoC Resource Controller functions are > > > > + accessed with four chip-selects. Reset control is on CS0. > > > > > > One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' > > > > > > Hard to say more because I don't have the whole thread nor remember what > > > exactly we discussed before. That was 100s of bindings ago... > > > > I agree and the example for v7 had all 4 chip-selects shown. > > That is not what I said. Look at 'reg' above again. You have 1 device, > but you have 4 nodes which looks like separate 4 devices. The > exception would be if what's on each chip select is independent from > each other. > > Describe what your h/w has/is/does so we can provide better guidance. This is the hardware design for every implementation with the Elba SoC Elba <-- spi --> One FPGA or CPLD (4 chip-selects) where there are four functions in the FPGA accessed by userspace applications except for emmc reset control which is a bit in a CS0 register. The IP at CS0 is a bunch of miscellaneous mgmt registers. CS1 is a designware I2C master/slave. CS2 is a Lattice dual I2C master. CS3 is internal storage for the CPLD or FPGA depending on the hardware implementation. 'reg = <0 1 2 3>' in the dt fragment below is indicating the chip-select which is what other bindings appear to be doing. Maybe one answer is delete this and add our compatible to spidev.c in the patchset we provide to customers. Adding our compatible to spidev.c was nack'ed. Recommendation? Not including 'reg' results in this compile warning: DTC arch/arm64/boot/dts/amd/elba-asic.dtb arch/arm64/boot/dts/amd/elba-asic-common.dtsi:73.28-78.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@0: missing or empty reg property arch/arm64/boot/dts/amd/elba-asic-common.dtsi:80.22-84.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@1: missing or empty reg property arch/arm64/boot/dts/amd/elba-asic-common.dtsi:86.22-92.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@2: missing or empty reg property arch/arm64/boot/dts/amd/elba-asic-common.dtsi:94.22-98.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@3: missing or empty reg property CALL scripts/atomic/check-atomics.sh &emmc { bus-width = <8>; cap-mmc-hw-reset; reset-names = "hw"; resets = <&rstc 0>; status = "okay"; }; &spi0 { #address-cells = <1>; #size-cells = <0>; num-cs = <4>; cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>, <&porta 7 GPIO_ACTIVE_LOW>; status = "okay"; rstc: system-controller@0 { compatible = "amd,pensando-elbasr"; reg = <0>; spi-max-frequency = <12000000>; #reset-cells = <1>; }; system-controller@1 { compatible = "amd,pensando-elbasr"; reg = <1>; spi-max-frequency = <12000000>; }; system-controller@2 { compatible = "amd,pensando-elbasr"; reg = <2>; spi-max-frequency = <12000000>; interrupt-parent = <&porta>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; system-controller@3 { compatible = "amd,pensando-elbasr"; reg = <3>; spi-max-frequency = <12000000>; }; }; Regards, Brad
Hi Brad, On Thu, Nov 17, 2022 at 7:39 PM Larson, Bradley <Bradley.Larson@amd.com> wrote: > > > > > --- /dev/null > > > > > +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml > > > ... > > > > > + > > > > > +title: AMD Pensando Elba SoC Resource Controller > > > > > + > > > > > +description: | > > > > > + AMD Pensando Elba SoC Resource Controller functions are > > > > > + accessed with four chip-selects. Reset control is on CS0. > > > > > > > > One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' > > > > > > > > Hard to say more because I don't have the whole thread nor remember what > > > > exactly we discussed before. That was 100s of bindings ago... > > > > > > I agree and the example for v7 had all 4 chip-selects shown. > > > > That is not what I said. Look at 'reg' above again. You have 1 device, > > but you have 4 nodes which looks like separate 4 devices. The > > exception would be if what's on each chip select is independent from > > each other. > > > > Describe what your h/w has/is/does so we can provide better guidance. > > This is the hardware design for every implementation with the Elba SoC > > Elba <-- spi --> One FPGA or CPLD (4 chip-selects) > > where there are four functions in the FPGA accessed by userspace applications except for emmc reset control which is a bit in a CS0 register. The IP at CS0 is a bunch of miscellaneous mgmt registers. CS1 is a designware I2C master/slave. CS2 is a Lattice dual I2C master. CS3 is internal storage for the CPLD or FPGA depending on the hardware implementation. > > 'reg = <0 1 2 3>' in the dt fragment below is indicating the chip-select which is what other bindings appear to be doing. Maybe one answer is delete this and add our compatible to spidev.c in the patchset we provide to customers. Adding our compatible to spidev.c was nack'ed. Recommendation? The fragment below does not have "reg = <0 1 2 3>", but individual subnodes, each with their own "reg" property. > Not including 'reg' results in this compile warning: > > DTC arch/arm64/boot/dts/amd/elba-asic.dtb > arch/arm64/boot/dts/amd/elba-asic-common.dtsi:73.28-78.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@0: missing or empty reg property > arch/arm64/boot/dts/amd/elba-asic-common.dtsi:80.22-84.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@1: missing or empty reg property > arch/arm64/boot/dts/amd/elba-asic-common.dtsi:86.22-92.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@2: missing or empty reg property > arch/arm64/boot/dts/amd/elba-asic-common.dtsi:94.22-98.4: Warning (spi_bus_reg): /soc/spi@2800/system-controller@3: missing or empty reg property > CALL scripts/atomic/check-atomics.sh > > &emmc { > bus-width = <8>; > cap-mmc-hw-reset; > reset-names = "hw"; > resets = <&rstc 0>; > status = "okay"; > }; > > &spi0 { > #address-cells = <1>; > #size-cells = <0>; > num-cs = <4>; > cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>, > <&porta 7 GPIO_ACTIVE_LOW>; > status = "okay"; > > rstc: system-controller@0 { > compatible = "amd,pensando-elbasr"; > reg = <0>; > spi-max-frequency = <12000000>; > #reset-cells = <1>; > }; > > system-controller@1 { > compatible = "amd,pensando-elbasr"; > reg = <1>; > spi-max-frequency = <12000000>; > }; > > system-controller@2 { > compatible = "amd,pensando-elbasr"; > reg = <2>; > spi-max-frequency = <12000000>; > interrupt-parent = <&porta>; > interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > }; > > system-controller@3 { > compatible = "amd,pensando-elbasr"; > reg = <3>; > spi-max-frequency = <12000000>; > }; The above describes 4 individual but further identical (they have the same compatible value) devices, while above you say they are not identical: The IP at CS0 is a bunch of miscellaneous mgmt registers. CS1 is a designware I2C master/slave. CS2 is a Lattice dual I2C master. CS3 is internal storage for the CPLD or FPGA depending on the hardware implementation. So either this should be modelled as a single subnode with 4 chip selects[*]: system-controller@0 { compatible = "amd,pensando-elbasr"; reg = <0 1 2 3 4>; spi-max-frequency = <12000000>; #reset-cells = <1>; }; or as 4 separate subnodes, each using 4 different compatible values. Giving the wildly different functionalities provided by each, you also need 4 binding documents. [*] I'm not sure the Linux SPI core actually supports this yet. > }; Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
[AMD Official Use Only - General] Hi Geert, From: Geert Uytterhoeven <geert@linux-m68k.org> Sent: Friday, November 18, 2022 12:42 AM > ... > > &spi0 { > > #address-cells = <1>; > > #size-cells = <0>; > > num-cs = <4>; > > cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>, > > <&porta 7 GPIO_ACTIVE_LOW>; > > status = "okay"; > > > > rstc: system-controller@0 { > > compatible = "amd,pensando-elbasr"; > > reg = <0>; > > spi-max-frequency = <12000000>; > > #reset-cells = <1>; > > }; > > > > system-controller@1 { > > compatible = "amd,pensando-elbasr"; > > reg = <1>; > > spi-max-frequency = <12000000>; > > }; > > > > system-controller@2 { > > compatible = "amd,pensando-elbasr"; > > reg = <2>; > > spi-max-frequency = <12000000>; > > interrupt-parent = <&porta>; > > interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > > }; > > > > system-controller@3 { > > compatible = "amd,pensando-elbasr"; > > reg = <3>; > > spi-max-frequency = <12000000>; > > }; > > The above describes 4 individual but further identical (they have the > same compatible value) devices, while above you say they are not identical: > > The IP at CS0 is a bunch of miscellaneous mgmt registers. > CS1 is a designware I2C master/slave. > CS2 is a Lattice dual I2C master. > CS3 is internal storage for the CPLD or FPGA depending on the > hardware implementation. > > So either this should be modelled as a single subnode with 4 chip > selects[*]: > > system-controller@0 { > compatible = "amd,pensando-elbasr"; > reg = <0 1 2 3 4>; > spi-max-frequency = <12000000>; > #reset-cells = <1>; > }; > > or as 4 separate subnodes, each using 4 different compatible values. > Giving the wildly different functionalities provided by each, you also need > 4 binding documents. > > [*] I'm not sure the Linux SPI core actually supports this yet. Thanks, I was unfamiliar with reg <0 ...> with differences between the nodes such as reset-cells for one and interrupts on another. Below dts boots ok and will change binding and driver as needed. &spi0 { #address-cells = <1>; #size-cells = <0>; num-cs = <4>; cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>, <&porta 7 GPIO_ACTIVE_LOW>; status = "okay"; rstc: system-controller@0 { compatible = "amd,pensando-elbasr"; reg = <0 1 2 3>; spi-max-frequency = <12000000>; interrupt-parent = <&porta>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; #reset-cells = <1>; }; }; Regards, Brad
Hi Rob, On Wednesday, November 16, 2022 2:30 PM, Rob Herring wrote: >On Wed, Nov 16, 2022 at 11:39:40AM -0800, Brad Larson wrote: >> Add support for the AMD Pensando Elba SoC System Resource chip >> using the SPI interface. > > Please resend the whole series properly threaded. Series sent as v9 >> +description: | >> + AMD Pensando Elba SoC Resource Controller functions are >> + accessed with four chip-selects. Reset control is on CS0. > > One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' > > Hard to say more because I don't have the whole thread nor remember what > exactly we discussed before. That was 100s of bindings ago... This has been changed to one device and four chip selects. This binding error is occuring for snps,dw-apb-ssi.yaml using reg for the chip selects. Any guidance on how to fix? $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml LINT Documentation/devicetree/bindings CHKDT Documentation/devicetree/bindings/processed-schema.json SCHEMA Documentation/devicetree/bindings/processed-schema.json DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: system-controller@0:reg: [[0], [1], [2], [3]] is too long From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml Binding: --- /dev/null +++ b/Documentation/devicetree/bindings/spi/amd,pensando-sr.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/amd,pensando-sr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AMD Pensando SoC Resource Controller + +description: | + AMD Pensando SoC Resource Controller is a set of control/status + registers accessed on four chip-selects. This device is present + in all Pensando SoC based designs. + + CS0 is a set of miscellaneous control/status registers to + include reset control. CS1/CS2 are for I2C peripherals. + CS3 is to access resource controller internal storage. + +maintainers: + - Brad Larson <blarson@amd.com> + +properties: + compatible: + const: amd,pensando-sr + + reg: + maxItems: 4 + minimum: 0 + maximum: 3 + description: + Device chip select number + + '#reset-cells': + const: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - spi-max-frequency + - '#reset-cells' + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <4>; + + system-controller@0 { + compatible = "amd,pensando-sr"; + reg = <0 1 2 3>; + spi-max-frequency = <12000000>; + interrupt-parent = <&porta>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + #reset-cells = <1>; + }; + }; + +... DT node, single device and using reg for four chip-selects &spi0 { #address-cells = <1>; #size-cells = <0>; num-cs = <4>; cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>, <&porta 7 GPIO_ACTIVE_LOW>; status = "okay"; rstc: system-controller@0 { compatible = "amd,pensando-sr"; reg = <0 1 2 3>; spi-max-frequency = <12000000>; interrupt-parent = <&porta>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; #reset-cells = <1>; }; }; Regards, Brad
On 30/01/2023 20:12, Brad Larson wrote: > Hi Rob, > > On Wednesday, November 16, 2022 2:30 PM, Rob Herring wrote: >> On Wed, Nov 16, 2022 at 11:39:40AM -0800, Brad Larson wrote: >>> Add support for the AMD Pensando Elba SoC System Resource chip >>> using the SPI interface. >> >> Please resend the whole series properly threaded. > > Series sent as v9 > >>> +description: | >>> + AMD Pensando Elba SoC Resource Controller functions are >>> + accessed with four chip-selects. Reset control is on CS0. >> >> One device with 4 chip-selects? Then I'd expect 'reg = <0 1 2 3>;' >> >> Hard to say more because I don't have the whole thread nor remember what >> exactly we discussed before. That was 100s of bindings ago... > > This has been changed to one device and four chip selects. This binding error > is occuring for snps,dw-apb-ssi.yaml using reg for the chip selects. Any > guidance on how to fix? > > $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml > LINT Documentation/devicetree/bindings > CHKDT Documentation/devicetree/bindings/processed-schema.json > SCHEMA Documentation/devicetree/bindings/processed-schema.json > DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb > /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: system-controller@0:reg: [[0], [1], [2], [3]] is too long > From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml Maybe this would work in snps,dw-apb-ssi for children: reg: items: minimum: 0 maximum: 3 Best regards, Krzysztof
Hi Krzysztof, On 01/02/2023 10:57, Krzysztof Kozlowski wrote: >On 30/01/2023 20:12, Brad Larson wrote: ... >> This has been changed to one device and four chip selects. This binding error >> is occuring for snps,dw-apb-ssi.yaml using reg for the chip selects. Any >> guidance on how to fix? >> >> $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml >> LINT Documentation/devicetree/bindings >> CHKDT Documentation/devicetree/bindings/processed-schema.json >> SCHEMA Documentation/devicetree/bindings/processed-schema.json >> DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb >> /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: system-controller@0:reg: [[0], [1], [2], [3]] is too long >> From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml > > Maybe this would work in snps,dw-apb-ssi for children: > > reg: > items: > minimum: 0 > maximum: 3 With the above change here in snps,dw-apb-ssi.yaml: - if: properties: compatible: contains: const: amd,pensando-elba-spi then: properties: reg: items: minimum: 0 maximum: 3 required: - amd,pensando-elba-syscon else: properties: amd,pensando-elba-syscon: false this is the result: $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml LINT Documentation/devicetree/bindings CHKDT Documentation/devicetree/bindings/processed-schema.json SCHEMA Documentation/devicetree/bindings/processed-schema.json DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: reg:0: [0, 10240, 0, 256] is too long From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: system-controller@0:reg: [[0], [1], [2], [3]] is too long From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml The binding snps,dw-apb-ssi.yaml has patternProperties defined this way: patternProperties: "^.*@[0-9a-f]+$": type: object properties: reg: minimum: 0 maximum: 3 - Removing patternProperties makes the error go away indicating an issue with minimum/maximum regex check and the number of items in the reg property which shouldn't be related. - Changing patternProperties to this makes the error go away. patternProperties: "^.*@[0-9a-f]+$": type: object properties: reg: maxItems: 4 - Using spmi.yaml as a reference and changing patternProperties to the following: patternProperties: "^.*@[0-9a-f]+$": type: object properties: reg: items: - maxItems: 4 items: - minimum: 0 - maximum: 3 required: - reg results in: $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml arch/arm64/Makefile:36: Detected assembler with broken .inst; disassembly will be unreliable LINT Documentation/devicetree/bindings CHKDT Documentation/devicetree/bindings/processed-schema.json /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml: patternProperties:^.*@[0-9a-f]+$:properties:reg:items: 'oneOf' conditional failed, one must be fixed: [{'maxItems': 4, 'items': [{'minimum': 0}, {'maximum': 3}]}] is not of type 'object' {'maxItems': 4, 'items': [{'minimum': 0}, {'maximum': 3}]} should not be valid under {'required': ['maxItems']} hint: "maxItems" is not needed with an "items" list from schema $id: http://devicetree.org/meta-schemas/keywords.yaml# SCHEMA Documentation/devicetree/bindings/processed-schema.json DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb - With this version for patternProperties, to retain minimum/maximum, the original error occurs: patternProperties: "^.*@[0-9a-f]+$": type: object properties: reg: items: - minItems: 1 items: - minimum: 0 - maximum: 3 required: - reg $ make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml arch/arm64/Makefile:36: Detected assembler with broken .inst; disassembly will be unreliable LINT Documentation/devicetree/bindings CHKDT Documentation/devicetree/bindings/processed-schema.json SCHEMA Documentation/devicetree/bindings/processed-schema.json DTC_CHK arch/arm64/boot/dts/amd/elba-asic.dtb /home/brad/linux.v10/arch/arm64/boot/dts/amd/elba-asic.dtb: spi@2800: system-controller@0:reg: [[0], [1], [2], [3]] is too long From schema: /home/brad/linux.v10/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml Regards, Brad
diff --git a/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml new file mode 100644 index 000000000000..622c93402a86 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/amd,pensando-elbasr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AMD Pensando Elba SoC Resource Controller + +description: | + AMD Pensando Elba SoC Resource Controller functions are + accessed with four chip-selects. Reset control is on CS0. + +maintainers: + - Brad Larson <blarson@amd.com> + +properties: + compatible: + enum: + - amd,pensando-elbasr + + "#reset-cells": + const: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - spi-max-frequency + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <4>; + + system-controller@0 { + compatible = "amd,pensando-elbasr"; + reg = <0>; + spi-max-frequency = <12000000>; + #reset-cells = <1>; + }; + + system-controller@2 { + compatible = "amd,pensando-elbasr"; + reg = <2>; + spi-max-frequency = <12000000>; + interrupt-parent = <&porta>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; + };
Add support for the AMD Pensando Elba SoC System Resource chip using the SPI interface. Signed-off-by: Brad Larson <blarson@amd.com> --- v8: - Apply review request changes and picked the two unique examples for the 4 chip-selects as one has the reset control support and the other an interrupt. Missed the --in-reply-to in git send-email for v7, included in this update. v7: - Use system-controller for the device with four chip-selects connected over spi. - Delete child by moving reset-controller into the parent. - Updated and used dtschema-2022.11 and yamllint-1.28.0 v6: - Expand description, rename nodes and change compatible usage v5: - Change to AMD Pensando instead of Pensando v4: - Change Maintained to Supported .../bindings/mfd/amd,pensando-elbasr.yaml | 60 +++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/amd,pensando-elbasr.yaml