| Message ID | 20230215155410.80944-2-andriy.shevchenko@linux.intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v1,1/2] mmc: atmel-mci: Get rid of external platform data | expand |
+ Arnd, Balamanikandan On Wed, 15 Feb 2023 at 16:53, Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote: > > The of_gpio.h is going to be removed. In preparation of that convert > the driver to the agnostic API. > > Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> This is the third attempt to get this done, within this release cycle. :-) Arnd's: https://lore.kernel.org/netdev/20230126135034.3320638-1-arnd@kernel.org/ Balamanikandan's: https://lore.kernel.org/all/20221226073908.17317-1-balamanikandan.gunasundar@microchip.com/ Actually, Balamanikandan's version was acked already in December by Linus Walleij and Ludovic, but I failed to apply it so I was requesting a rebase. That said, I think we should give BalaBalamanikandan some more time for a re-spin (unless someone is willing to help him out in this regard), as it's getting late for v6.3 anyway. Kind regards Uffe > --- > drivers/mmc/host/atmel-mci.c | 106 ++++++++++++++++------------------- > 1 file changed, 48 insertions(+), 58 deletions(-) > > diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c > index fad5e6b4c654..79876e3152e6 100644 > --- a/drivers/mmc/host/atmel-mci.c > +++ b/drivers/mmc/host/atmel-mci.c > @@ -11,7 +11,7 @@ > #include <linux/dmaengine.h> > #include <linux/dma-mapping.h> > #include <linux/err.h> > -#include <linux/gpio.h> > +#include <linux/gpio/consumer.h> > #include <linux/init.h> > #include <linux/interrupt.h> > #include <linux/io.h> > @@ -19,7 +19,6 @@ > #include <linux/module.h> > #include <linux/of.h> > #include <linux/of_device.h> > -#include <linux/of_gpio.h> > #include <linux/platform_device.h> > #include <linux/scatterlist.h> > #include <linux/seq_file.h> > @@ -44,8 +43,8 @@ > /** > * struct mci_slot_pdata - board-specific per-slot configuration > * @bus_width: Number of data lines wired up the slot > - * @detect_pin: GPIO pin wired to the card detect switch > - * @wp_pin: GPIO pin wired to the write protect sensor > + * @wp_gpio: GPIO pin wired to the write protect sensor > + * @detect_gpio: GPIO pin wired to the card detect switch > * @detect_is_active_high: The state of the detect pin when it is active > * @non_removable: The slot is not removable, only detect once > * > @@ -60,8 +59,8 @@ > */ > struct mci_slot_pdata { > unsigned int bus_width; > - int detect_pin; > - int wp_pin; > + struct gpio_desc *wp_gpio; > + struct gpio_desc *detect_gpio; > bool detect_is_active_high; > bool non_removable; > }; > @@ -399,12 +398,12 @@ struct atmel_mci { > * &struct atmel_mci. > * @clock: Clock rate configured by set_ios(). Protected by host->lock. > * @flags: Random state bits associated with the slot. > - * @detect_pin: GPIO pin used for card detection, or negative if not > - * available. > - * @wp_pin: GPIO pin used for card write protect sending, or negative > + * @wp_gpio: GPIO pin used for card write protect sending, or NULL > * if not available. > + * @detect_gpio: GPIO pin used for card detection, or negative if not > + * available. > * @detect_is_active_high: The state of the detect pin when it is active. > - * @detect_timer: Timer used for debouncing @detect_pin interrupts. > + * @detect_timer: Timer used for debouncing @detect_gpio interrupts. > */ > struct atmel_mci_slot { > struct mmc_host *mmc; > @@ -422,8 +421,9 @@ struct atmel_mci_slot { > #define ATMCI_CARD_NEED_INIT 1 > #define ATMCI_SHUTDOWN 2 > > - int detect_pin; > - int wp_pin; > + struct gpio_desc *wp_gpio; > + > + struct gpio_desc *detect_gpio; > bool detect_is_active_high; > > struct timer_list detect_timer; > @@ -637,7 +637,8 @@ MODULE_DEVICE_TABLE(of, atmci_dt_ids); > static struct mci_platform_data* > atmci_of_init(struct platform_device *pdev) > { > - struct device_node *np = pdev->dev.of_node; > + struct device *dev = &pdev->dev; > + struct device_node *np = dev->of_node; > struct device_node *cnp; > struct mci_platform_data *pdata; > u32 slot_id; > @@ -669,8 +670,10 @@ atmci_of_init(struct platform_device *pdev) > &pdata->slot[slot_id].bus_width)) > pdata->slot[slot_id].bus_width = 1; > > - pdata->slot[slot_id].detect_pin = > - of_get_named_gpio(cnp, "cd-gpios", 0); > + pdata->slot[slot_id].detect_gpio = devm_gpiod_get_optional(dev, "cd", GPIOD_IN); > + if (!pdata->slot[slot_id].detect_gpio) > + dev_dbg(dev, "no detect pin available\n"); > + gpiod_set_consumer_name(pdata->slot[slot_id].detect_gpio, "mmc_detect"); > > pdata->slot[slot_id].detect_is_active_high = > of_property_read_bool(cnp, "cd-inverted"); > @@ -678,8 +681,10 @@ atmci_of_init(struct platform_device *pdev) > pdata->slot[slot_id].non_removable = > of_property_read_bool(cnp, "non-removable"); > > - pdata->slot[slot_id].wp_pin = > - of_get_named_gpio(cnp, "wp-gpios", 0); > + pdata->slot[slot_id].wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_IN); > + if (!pdata->slot[slot_id].wp_gpio) > + dev_dbg(dev, "no WP pin available\n"); > + gpiod_set_consumer_name(pdata->slot[slot_id].wp_gpio, "mmc_wp"); > } > > return pdata; > @@ -1535,8 +1540,8 @@ static int atmci_get_ro(struct mmc_host *mmc) > int read_only = -ENOSYS; > struct atmel_mci_slot *slot = mmc_priv(mmc); > > - if (gpio_is_valid(slot->wp_pin)) { > - read_only = gpio_get_value(slot->wp_pin); > + if (slot->wp_gpio) { > + read_only = gpiod_get_value(slot->wp_gpio); > dev_dbg(&mmc->class_dev, "card is %s\n", > read_only ? "read-only" : "read-write"); > } > @@ -1544,14 +1549,18 @@ static int atmci_get_ro(struct mmc_host *mmc) > return read_only; > } > > +static bool is_card_present(struct atmel_mci_slot *slot) > +{ > + return !(gpiod_get_raw_value(slot->detect_gpio) ^ slot->detect_is_active_high); > +} > + > static int atmci_get_cd(struct mmc_host *mmc) > { > int present = -ENOSYS; > struct atmel_mci_slot *slot = mmc_priv(mmc); > > - if (gpio_is_valid(slot->detect_pin)) { > - present = !(gpio_get_value(slot->detect_pin) ^ > - slot->detect_is_active_high); > + if (slot->detect_gpio) { > + present = is_card_present(slot); > dev_dbg(&mmc->class_dev, "card is %spresent\n", > present ? "" : "not "); > } > @@ -1663,9 +1672,8 @@ static void atmci_detect_change(struct timer_list *t) > if (test_bit(ATMCI_SHUTDOWN, &slot->flags)) > return; > > - enable_irq(gpio_to_irq(slot->detect_pin)); > - present = !(gpio_get_value(slot->detect_pin) ^ > - slot->detect_is_active_high); > + enable_irq(gpiod_to_irq(slot->detect_gpio)); > + present = is_card_present(slot); > present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags); > > dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n", > @@ -2254,18 +2262,18 @@ static int atmci_init_slot(struct atmel_mci *host, > slot = mmc_priv(mmc); > slot->mmc = mmc; > slot->host = host; > - slot->detect_pin = slot_data->detect_pin; > - slot->wp_pin = slot_data->wp_pin; > + slot->wp_gpio = slot_data->wp_gpio; > + slot->detect_gpio = slot_data->detect_gpio; > slot->detect_is_active_high = slot_data->detect_is_active_high; > slot->sdc_reg = sdc_reg; > slot->sdio_irq = sdio_irq; > > dev_dbg(&mmc->class_dev, > - "slot[%u]: bus_width=%u, detect_pin=%d, " > - "detect_is_active_high=%s, wp_pin=%d\n", > - id, slot_data->bus_width, slot_data->detect_pin, > + "slot[%u]: bus_width=%u, detect_gpio=%d, " > + "detect_is_active_high=%s, wp_gpio=%d\n", > + id, slot_data->bus_width, desc_to_gpio(slot_data->detect_gpio), > slot_data->detect_is_active_high ? "true" : "false", > - slot_data->wp_pin); > + desc_to_gpio(slot_data->wp_gpio)); > > mmc->ops = &atmci_ops; > mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512); > @@ -2301,32 +2309,16 @@ static int atmci_init_slot(struct atmel_mci *host, > > /* Assume card is present initially */ > set_bit(ATMCI_CARD_PRESENT, &slot->flags); > - if (gpio_is_valid(slot->detect_pin)) { > - if (devm_gpio_request(&host->pdev->dev, slot->detect_pin, > - "mmc_detect")) { > - dev_dbg(&mmc->class_dev, "no detect pin available\n"); > - slot->detect_pin = -EBUSY; > - } else if (gpio_get_value(slot->detect_pin) ^ > - slot->detect_is_active_high) { > + if (slot->detect_gpio) { > + if (!is_card_present(slot)) > clear_bit(ATMCI_CARD_PRESENT, &slot->flags); > - } > - } > - > - if (!gpio_is_valid(slot->detect_pin)) { > + } else { > if (slot_data->non_removable) > mmc->caps |= MMC_CAP_NONREMOVABLE; > else > mmc->caps |= MMC_CAP_NEEDS_POLL; > } > > - if (gpio_is_valid(slot->wp_pin)) { > - if (devm_gpio_request(&host->pdev->dev, slot->wp_pin, > - "mmc_wp")) { > - dev_dbg(&mmc->class_dev, "no WP pin available\n"); > - slot->wp_pin = -EBUSY; > - } > - } > - > host->slot[id] = slot; > mmc_regulator_get_supply(mmc); > ret = mmc_add_host(mmc); > @@ -2335,18 +2327,18 @@ static int atmci_init_slot(struct atmel_mci *host, > return ret; > } > > - if (gpio_is_valid(slot->detect_pin)) { > + if (slot->detect_gpio) { > timer_setup(&slot->detect_timer, atmci_detect_change, 0); > > - ret = request_irq(gpio_to_irq(slot->detect_pin), > + ret = request_irq(gpiod_to_irq(slot->detect_gpio), > atmci_detect_interrupt, > IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, > "mmc-detect", slot); > if (ret) { > dev_dbg(&mmc->class_dev, > "could not request IRQ %d for detect pin\n", > - gpio_to_irq(slot->detect_pin)); > - slot->detect_pin = -EBUSY; > + gpiod_to_irq(slot->detect_gpio)); > + slot->detect_gpio = NULL; > } > } > > @@ -2365,10 +2357,8 @@ static void atmci_cleanup_slot(struct atmel_mci_slot *slot, > > mmc_remove_host(slot->mmc); > > - if (gpio_is_valid(slot->detect_pin)) { > - int pin = slot->detect_pin; > - > - free_irq(gpio_to_irq(pin), slot); > + if (slot->detect_gpio) { > + free_irq(gpiod_to_irq(slot->detect_gpio), slot); > del_timer_sync(&slot->detect_timer); > } > > -- > 2.39.1 >
On Thu, Feb 16, 2023 at 12:09:46PM +0100, Ulf Hansson wrote: > On Wed, 15 Feb 2023 at 16:53, Andy Shevchenko > <andriy.shevchenko@linux.intel.com> wrote: > > > > The of_gpio.h is going to be removed. In preparation of that convert > > the driver to the agnostic API. > > > > Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> > > This is the third attempt to get this done, within this release cycle. :-) > > Arnd's: > https://lore.kernel.org/netdev/20230126135034.3320638-1-arnd@kernel.org/ > > Balamanikandan's: > https://lore.kernel.org/all/20221226073908.17317-1-balamanikandan.gunasundar@microchip.com/ > > Actually, Balamanikandan's version was acked already in December by > Linus Walleij and Ludovic, but I failed to apply it so I was > requesting a rebase. > > That said, I think we should give BalaBalamanikandan some more time > for a re-spin (unless someone is willing to help him out in this > regard), as it's getting late for v6.3 anyway. I see, thanks for heads up! I believe there is still room for improvement in his series (I briefly looked at it). Let's wait for v4 which I would like to review.
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index fad5e6b4c654..79876e3152e6 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -11,7 +11,7 @@ #include <linux/dmaengine.h> #include <linux/dma-mapping.h> #include <linux/err.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/init.h> #include <linux/interrupt.h> #include <linux/io.h> @@ -19,7 +19,6 @@ #include <linux/module.h> #include <linux/of.h> #include <linux/of_device.h> -#include <linux/of_gpio.h> #include <linux/platform_device.h> #include <linux/scatterlist.h> #include <linux/seq_file.h> @@ -44,8 +43,8 @@ /** * struct mci_slot_pdata - board-specific per-slot configuration * @bus_width: Number of data lines wired up the slot - * @detect_pin: GPIO pin wired to the card detect switch - * @wp_pin: GPIO pin wired to the write protect sensor + * @wp_gpio: GPIO pin wired to the write protect sensor + * @detect_gpio: GPIO pin wired to the card detect switch * @detect_is_active_high: The state of the detect pin when it is active * @non_removable: The slot is not removable, only detect once * @@ -60,8 +59,8 @@ */ struct mci_slot_pdata { unsigned int bus_width; - int detect_pin; - int wp_pin; + struct gpio_desc *wp_gpio; + struct gpio_desc *detect_gpio; bool detect_is_active_high; bool non_removable; }; @@ -399,12 +398,12 @@ struct atmel_mci { * &struct atmel_mci. * @clock: Clock rate configured by set_ios(). Protected by host->lock. * @flags: Random state bits associated with the slot. - * @detect_pin: GPIO pin used for card detection, or negative if not - * available. - * @wp_pin: GPIO pin used for card write protect sending, or negative + * @wp_gpio: GPIO pin used for card write protect sending, or NULL * if not available. + * @detect_gpio: GPIO pin used for card detection, or negative if not + * available. * @detect_is_active_high: The state of the detect pin when it is active. - * @detect_timer: Timer used for debouncing @detect_pin interrupts. + * @detect_timer: Timer used for debouncing @detect_gpio interrupts. */ struct atmel_mci_slot { struct mmc_host *mmc; @@ -422,8 +421,9 @@ struct atmel_mci_slot { #define ATMCI_CARD_NEED_INIT 1 #define ATMCI_SHUTDOWN 2 - int detect_pin; - int wp_pin; + struct gpio_desc *wp_gpio; + + struct gpio_desc *detect_gpio; bool detect_is_active_high; struct timer_list detect_timer; @@ -637,7 +637,8 @@ MODULE_DEVICE_TABLE(of, atmci_dt_ids); static struct mci_platform_data* atmci_of_init(struct platform_device *pdev) { - struct device_node *np = pdev->dev.of_node; + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; struct device_node *cnp; struct mci_platform_data *pdata; u32 slot_id; @@ -669,8 +670,10 @@ atmci_of_init(struct platform_device *pdev) &pdata->slot[slot_id].bus_width)) pdata->slot[slot_id].bus_width = 1; - pdata->slot[slot_id].detect_pin = - of_get_named_gpio(cnp, "cd-gpios", 0); + pdata->slot[slot_id].detect_gpio = devm_gpiod_get_optional(dev, "cd", GPIOD_IN); + if (!pdata->slot[slot_id].detect_gpio) + dev_dbg(dev, "no detect pin available\n"); + gpiod_set_consumer_name(pdata->slot[slot_id].detect_gpio, "mmc_detect"); pdata->slot[slot_id].detect_is_active_high = of_property_read_bool(cnp, "cd-inverted"); @@ -678,8 +681,10 @@ atmci_of_init(struct platform_device *pdev) pdata->slot[slot_id].non_removable = of_property_read_bool(cnp, "non-removable"); - pdata->slot[slot_id].wp_pin = - of_get_named_gpio(cnp, "wp-gpios", 0); + pdata->slot[slot_id].wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_IN); + if (!pdata->slot[slot_id].wp_gpio) + dev_dbg(dev, "no WP pin available\n"); + gpiod_set_consumer_name(pdata->slot[slot_id].wp_gpio, "mmc_wp"); } return pdata; @@ -1535,8 +1540,8 @@ static int atmci_get_ro(struct mmc_host *mmc) int read_only = -ENOSYS; struct atmel_mci_slot *slot = mmc_priv(mmc); - if (gpio_is_valid(slot->wp_pin)) { - read_only = gpio_get_value(slot->wp_pin); + if (slot->wp_gpio) { + read_only = gpiod_get_value(slot->wp_gpio); dev_dbg(&mmc->class_dev, "card is %s\n", read_only ? "read-only" : "read-write"); } @@ -1544,14 +1549,18 @@ static int atmci_get_ro(struct mmc_host *mmc) return read_only; } +static bool is_card_present(struct atmel_mci_slot *slot) +{ + return !(gpiod_get_raw_value(slot->detect_gpio) ^ slot->detect_is_active_high); +} + static int atmci_get_cd(struct mmc_host *mmc) { int present = -ENOSYS; struct atmel_mci_slot *slot = mmc_priv(mmc); - if (gpio_is_valid(slot->detect_pin)) { - present = !(gpio_get_value(slot->detect_pin) ^ - slot->detect_is_active_high); + if (slot->detect_gpio) { + present = is_card_present(slot); dev_dbg(&mmc->class_dev, "card is %spresent\n", present ? "" : "not "); } @@ -1663,9 +1672,8 @@ static void atmci_detect_change(struct timer_list *t) if (test_bit(ATMCI_SHUTDOWN, &slot->flags)) return; - enable_irq(gpio_to_irq(slot->detect_pin)); - present = !(gpio_get_value(slot->detect_pin) ^ - slot->detect_is_active_high); + enable_irq(gpiod_to_irq(slot->detect_gpio)); + present = is_card_present(slot); present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags); dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n", @@ -2254,18 +2262,18 @@ static int atmci_init_slot(struct atmel_mci *host, slot = mmc_priv(mmc); slot->mmc = mmc; slot->host = host; - slot->detect_pin = slot_data->detect_pin; - slot->wp_pin = slot_data->wp_pin; + slot->wp_gpio = slot_data->wp_gpio; + slot->detect_gpio = slot_data->detect_gpio; slot->detect_is_active_high = slot_data->detect_is_active_high; slot->sdc_reg = sdc_reg; slot->sdio_irq = sdio_irq; dev_dbg(&mmc->class_dev, - "slot[%u]: bus_width=%u, detect_pin=%d, " - "detect_is_active_high=%s, wp_pin=%d\n", - id, slot_data->bus_width, slot_data->detect_pin, + "slot[%u]: bus_width=%u, detect_gpio=%d, " + "detect_is_active_high=%s, wp_gpio=%d\n", + id, slot_data->bus_width, desc_to_gpio(slot_data->detect_gpio), slot_data->detect_is_active_high ? "true" : "false", - slot_data->wp_pin); + desc_to_gpio(slot_data->wp_gpio)); mmc->ops = &atmci_ops; mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512); @@ -2301,32 +2309,16 @@ static int atmci_init_slot(struct atmel_mci *host, /* Assume card is present initially */ set_bit(ATMCI_CARD_PRESENT, &slot->flags); - if (gpio_is_valid(slot->detect_pin)) { - if (devm_gpio_request(&host->pdev->dev, slot->detect_pin, - "mmc_detect")) { - dev_dbg(&mmc->class_dev, "no detect pin available\n"); - slot->detect_pin = -EBUSY; - } else if (gpio_get_value(slot->detect_pin) ^ - slot->detect_is_active_high) { + if (slot->detect_gpio) { + if (!is_card_present(slot)) clear_bit(ATMCI_CARD_PRESENT, &slot->flags); - } - } - - if (!gpio_is_valid(slot->detect_pin)) { + } else { if (slot_data->non_removable) mmc->caps |= MMC_CAP_NONREMOVABLE; else mmc->caps |= MMC_CAP_NEEDS_POLL; } - if (gpio_is_valid(slot->wp_pin)) { - if (devm_gpio_request(&host->pdev->dev, slot->wp_pin, - "mmc_wp")) { - dev_dbg(&mmc->class_dev, "no WP pin available\n"); - slot->wp_pin = -EBUSY; - } - } - host->slot[id] = slot; mmc_regulator_get_supply(mmc); ret = mmc_add_host(mmc); @@ -2335,18 +2327,18 @@ static int atmci_init_slot(struct atmel_mci *host, return ret; } - if (gpio_is_valid(slot->detect_pin)) { + if (slot->detect_gpio) { timer_setup(&slot->detect_timer, atmci_detect_change, 0); - ret = request_irq(gpio_to_irq(slot->detect_pin), + ret = request_irq(gpiod_to_irq(slot->detect_gpio), atmci_detect_interrupt, IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, "mmc-detect", slot); if (ret) { dev_dbg(&mmc->class_dev, "could not request IRQ %d for detect pin\n", - gpio_to_irq(slot->detect_pin)); - slot->detect_pin = -EBUSY; + gpiod_to_irq(slot->detect_gpio)); + slot->detect_gpio = NULL; } } @@ -2365,10 +2357,8 @@ static void atmci_cleanup_slot(struct atmel_mci_slot *slot, mmc_remove_host(slot->mmc); - if (gpio_is_valid(slot->detect_pin)) { - int pin = slot->detect_pin; - - free_irq(gpio_to_irq(pin), slot); + if (slot->detect_gpio) { + free_irq(gpiod_to_irq(slot->detect_gpio), slot); del_timer_sync(&slot->detect_timer); }
The of_gpio.h is going to be removed. In preparation of that convert the driver to the agnostic API. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> --- drivers/mmc/host/atmel-mci.c | 106 ++++++++++++++++------------------- 1 file changed, 48 insertions(+), 58 deletions(-)