@@ -762,6 +762,19 @@ config MMC_DW_PLTFM
If unsure, say Y.
+config MMC_DW_CQE
+ tristate "Synopsys DesignWare Memory Card with CQE Interface"
+ depends on ARC || ARM || ARM64 || MIPS || COMPILE_TEST
+ select MMC_CQHCI
+ help
+ This selects support for the Synopsys DesignWare Mobile Storage IP
+ block after JEDEC Standard version 5.1. Select this option for SD and
+ MMC interfaces that use command queue.
+
+ If you have a controller with this interface, say Y or M here.
+
+ If unsure, say Y.
+
config MMC_DW_BLUEFIELD
tristate "BlueField specific extensions for Synopsys DW Memory Card Interface"
depends on MMC_DW
@@ -55,6 +55,7 @@ obj-$(CONFIG_MMC_DW_K3) += dw_mmc-k3.o
obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
obj-$(CONFIG_MMC_DW_ROCKCHIP) += dw_mmc-rockchip.o
obj-$(CONFIG_MMC_DW_STARFIVE) += dw_mmc-starfive.o
+obj-$(CONFIG_MMC_DW_CQE) += dw_mmc_cqe.o
obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
obj-$(CONFIG_MMC_VUB300) += vub300.o
new file mode 100644
@@ -0,0 +1,1619 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Synopsys DesignWare Multimedia Card Interface driver with CMDQ support
+ * (Based on Synopsys DesignWare Multimedia Card Interface driver)
+ *
+ * Copyright (c) 2023 Realtek Semiconductor Corp
+ */
+
+#include <linux/bitops.h>
+#include <linux/blkdev.h>
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/slot-gpio.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/seq_file.h>
+#include <linux/sizes.h>
+#include <linux/slab.h>
+#include <linux/stat.h>
+
+#include "dw_mmc_cqe.h"
+#include "cqhci.h"
+
+#define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
+#define DW_MCI_FREQ_MIN 100000 /* unit: HZ */
+#define DW_MCI_CMDQ_DISABLED 0x30f0001
+#define DW_MCI_CMDQ_ENABLED 0x30f0101
+#define DW_MCI_POWEROFF 0x3220301
+#define DW_MCI_DESC_LEN 0x100000
+#define DW_MCI_MAX_SCRIPT_BLK 128
+#define DW_MCI_TIMEOUT_Ms 200
+#define DW_MCI_TIMEOUT 200000
+#define TUNING_ERR 531
+#define DW_MCI_NOT_READY 9999
+
+DECLARE_COMPLETION(dw_mci_wait);
+
+#if defined(CONFIG_DEBUG_FS)
+static int dw_mci_cqe_req_show(struct seq_file *s, void *v)
+{
+ struct dw_mci_slot *slot = s->private;
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_command *stop;
+ struct mmc_data *data;
+
+ /* Make sure we get a consistent snapshot */
+ spin_lock_bh(&slot->host->lock);
+ mrq = slot->mrq;
+
+ if (mrq) {
+ cmd = mrq->cmd;
+ data = mrq->data;
+ stop = mrq->stop;
+
+ if (cmd)
+ seq_printf(s,
+ "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
+ cmd->opcode, cmd->arg, cmd->flags,
+ cmd->resp[0], cmd->resp[1], cmd->resp[2],
+ cmd->resp[2], cmd->error);
+ if (data)
+ seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
+ data->bytes_xfered, data->blocks,
+ data->blksz, data->flags, data->error);
+ if (stop)
+ seq_printf(s,
+ "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
+ stop->opcode, stop->arg, stop->flags,
+ stop->resp[0], stop->resp[1], stop->resp[2],
+ stop->resp[2], stop->error);
+ }
+
+ spin_unlock_bh(&slot->host->lock);
+
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(dw_mci_cqe_req);
+#endif /* defined(CONFIG_DEBUG_FS) */
+
+static int dw_mci_cqe_regs_show(struct dw_mci *host,
+ struct mmc_command *cmd, u32 cmd_flags)
+{
+ dev_err(host->dev, "opcode = %d, arg = 0x%x, cmdflags = 0x%x\n",
+ cmd->opcode, cmd->arg, cmd_flags);
+ dev_err(host->dev, "status_int = 0x%x\n", host->normal_interrupt);
+ dev_err(host->dev, "error_int = 0x%x\n", host->error_interrupt);
+ dev_err(host->dev, "auto_error_int = 0x%x\n", host->auto_error_interrupt);
+
+ return 0;
+}
+
+static void dw_mci_cqe_dumpregs(struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ dev_info(host->dev, "%s: cmd idx 0x%08x\n", __func__, mcq_readw(host, CMD_R));
+}
+
+static void dw_mci_cqe_setup_tran_desc(struct mmc_data *data,
+ struct cqhci_host *cq_host,
+ u8 *desc,
+ int sg_count)
+{
+ struct scatterlist *sg;
+ u32 cur_blk_cnt, remain_blk_cnt;
+ unsigned int begin, end;
+ int i, len;
+ bool last = false;
+ bool dma64 = cq_host->dma64;
+ dma_addr_t addr;
+
+ for_each_sg(data->sg, sg, sg_count, i) {
+ addr = sg_dma_address(sg);
+ len = sg_dma_len(sg);
+ remain_blk_cnt = len >> 9;
+
+ while (remain_blk_cnt) {
+ /*DW_MCI_MAX_SCRIPT_BLK is tha max for each descriptor record*/
+ if (remain_blk_cnt > DW_MCI_MAX_SCRIPT_BLK)
+ cur_blk_cnt = DW_MCI_MAX_SCRIPT_BLK;
+ else
+ cur_blk_cnt = remain_blk_cnt;
+
+ /* In Synopsys DesignWare Databook Page 84,
+ * They mentioned the DMA 128MB restriction
+ */
+ begin = addr / SZ_128M;
+ end = (addr + cur_blk_cnt * SZ_512) / SZ_128M;
+
+ if (begin != end)
+ cur_blk_cnt = (end * SZ_128M - addr) / SZ_512;
+
+ if ((i+1) == sg_count && (remain_blk_cnt == cur_blk_cnt))
+ last = true;
+
+ cqhci_set_tran_desc(desc, addr,
+ (cur_blk_cnt << 9), last, dma64);
+
+ addr = addr + (cur_blk_cnt << 9);
+ remain_blk_cnt -= cur_blk_cnt;
+ desc += cq_host->trans_desc_len;
+ }
+ }
+}
+
+static void dw_mci_cqe_enable(struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ /*clear data path SW_RST_R.SW_RST_DAT = 1*/
+ mcq_writeb(host, SW_RST_R, SDMMC_RST_DAT);
+ /*0x9801200c*/
+ mcq_writew(host, XFER_MODE_R,
+ ((1 << SDMMC_MULTI_BLK_SEL) | SDMMC_BLOCK_COUNT_ENABLE | SDMMC_DMA_ENABLE));
+
+ /*Set DMA_SEL to ADMA2 only mode in the HOST_CTRL1_R*/
+ mcq_writeb(host, HOST_CTRL1_R,
+ (mcq_readb(host, HOST_CTRL1_R) & 0xe7) | (SDMMC_ADMA2_32 << SDMMC_DMA_SEL));
+ mcq_writew(host, BLOCKSIZE_R, 0x200);
+ mcq_writew(host, BLOCKCOUNT_R, 0);
+
+ /*Set SDMASA_R (while using 32 bits) to 0*/
+ mcq_writel(host, SDMASA_R, 0);
+ /*we set this register additionally to enhance the IO perofrmance*/
+
+ cqhci_writel(host->cqe, 0x10, CQHCI_SSC1);
+ cqhci_writel(host->cqe, 0, CQHCI_CTL);
+
+ if (cqhci_readl(host->cqe, CQHCI_CTL) && CQHCI_HALT) {
+ dev_err(host->dev, "%s: cqhci: CQE failed to exit halt state\n",
+ mmc_hostname(mmc));
+ }
+
+ /*cmdq interrupt mode*/
+ dw_mci_clr_signal_int(host);
+ dw_mci_en_cqe_int(host);
+}
+
+static void dw_mci_cqe_pre_enable(struct mmc_host *mmc)
+{
+ struct cqhci_host *cq_host = mmc->cqe_private;
+ u32 reg;
+
+ reg = cqhci_readl(cq_host, CQHCI_CFG);
+ reg |= CQHCI_ENABLE;
+ cqhci_writel(cq_host, reg, CQHCI_CFG);
+}
+
+static void dw_mci_cqe_post_disable(struct mmc_host *mmc)
+{
+ struct cqhci_host *cq_host = mmc->cqe_private;
+ u32 reg;
+
+ reg = cqhci_readl(cq_host, CQHCI_CFG);
+ reg &= ~CQHCI_ENABLE;
+ cqhci_writel(cq_host, reg, CQHCI_CFG);
+}
+
+static const struct cqhci_host_ops dw_mci_cqhci_host_ops = {
+ .enable = dw_mci_cqe_enable,
+ .dumpregs = dw_mci_cqe_dumpregs,
+ .pre_enable = dw_mci_cqe_pre_enable,
+ .post_disable = dw_mci_cqe_post_disable,
+ .setup_tran_desc = dw_mci_cqe_setup_tran_desc,
+};
+
+static void dw_mci_cqe_reset(struct dw_mci *host)
+{
+ int ret;
+ u32 status;
+ /*check the cmd line*/
+ if (mcq_readw(host, ERROR_INT_STAT_R) & SDMMC_CMD_ERR) {
+ /*Perform a software reset*/
+ mcq_writeb(host, SW_RST_R, SDMMC_RST_CMD);
+
+ ret = readl_poll_timeout(host->regs + SDMMC_CLK_CTRL_R, status,
+ (status & SW_RST_CMD_DONE) == 0x0, 10, DW_MCI_TIMEOUT);
+ if (ret)
+ dev_err(host->dev, "Timeout resetting CMD line\n");
+ }
+ /*check data line*/
+ if (mcq_readw(host, ERROR_INT_STAT_R) & SDMMC_DATA_ERR) {
+ mcq_writeb(host, SW_RST_R, SDMMC_RST_DAT);
+
+ ret = readl_poll_timeout(host->regs + SDMMC_CLK_CTRL_R, status,
+ (status & SW_RST_DATA_DONE) == 0x0, 10, DW_MCI_TIMEOUT);
+ if (ret)
+ dev_err(host->dev, "Timeout resetting DATA line\n");
+ }
+}
+
+static void dw_mci_cqe_read_rsp(struct dw_mci *host, struct mmc_command *cmd, u32 *rsp)
+{
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ /*R2 long response*/
+ u32 rsp_tmp[4];
+
+ rsp_tmp[3] = mcq_readl(host, RESP01_R);
+ rsp_tmp[2] = mcq_readl(host, RESP23_R);
+ rsp_tmp[1] = mcq_readl(host, RESP45_R);
+ rsp_tmp[0] = mcq_readl(host, RESP67_R);
+
+ /* dw_mmc_databook shift Response field to 08 - 139 bits*/
+ rsp[3] = (rsp_tmp[3] & 0x00ffffff) << 8;
+ rsp[2] = ((rsp_tmp[2] & 0x00ffffff) << 8)
+ | ((rsp_tmp[3] & 0xff000000) >> 24);
+ rsp[1] = ((rsp_tmp[1] & 0x00ffffff) << 8)
+ | ((rsp_tmp[2] & 0xff000000) >> 24);
+ rsp[0] = ((rsp_tmp[0] & 0x00ffffff) << 8)
+ | ((rsp_tmp[1] & 0xff000000) >> 24);
+ } else {
+ /*Short response*/
+ rsp[0] = rsp[1] = rsp[2] = rsp[3] = 0;
+ rsp[0] = mcq_readl(host, RESP01_R);
+ }
+ }
+}
+
+static u32 dw_mci_cqe_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
+{
+ u32 cmdr;
+
+ cmd->error = -EINPROGRESS;
+ cmdr = (cmd->opcode << 8);
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136)
+ cmdr |= SDMMC_RESP_LEN_136;
+ else {
+ if (cmd->flags & MMC_RSP_BUSY)
+ cmdr |= SDMMC_RESP_LEN_48B;
+ else
+ cmdr |= SDMMC_RESP_LEN_48;
+ }
+ }
+
+ cmdr |= SDMMC_CMD_CHK_RESP_CRC;
+ if (cmd->opcode == MMC_GO_IDLE_STATE ||
+ cmd->opcode == MMC_SEND_OP_COND ||
+ (cmd->opcode == MMC_SELECT_CARD && cmd->flags == (MMC_RSP_NONE | MMC_CMD_AC)))
+ cmdr &= ~SDMMC_CMD_CHK_RESP_CRC;
+
+ cmdr |= SDMMC_CMD_IDX_CHK_ENABLE;
+ if (cmd->opcode == MMC_GO_IDLE_STATE ||
+ cmd->opcode == MMC_SEND_OP_COND ||
+ cmd->opcode == MMC_SEND_CSD ||
+ cmd->opcode == MMC_SEND_CID ||
+ cmd->opcode == MMC_ALL_SEND_CID ||
+ (cmd->opcode == MMC_SELECT_CARD && cmd->flags == (MMC_RSP_NONE | MMC_CMD_AC)))
+ cmdr &= ~SDMMC_CMD_IDX_CHK_ENABLE;
+
+ if (cmd->data)
+ cmdr |= SDMMC_DATA;
+
+ if (cmd->opcode == MMC_STOP_TRANSMISSION)
+ cmdr |= (SDMMC_ABORT_CMD << 6);
+
+ return cmdr;
+}
+
+static int dw_mci_cqe_start_command(struct dw_mci *host,
+ struct mmc_command *cmd, u32 cmd_flags)
+{
+ int err = 0;
+ unsigned long end = 0;
+ unsigned long flags;
+ bool xfer_flag = false;
+ int ret;
+ u32 status;
+
+ host->cmd = cmd;
+
+ switch (cmd->opcode) {
+ case MMC_READ_SINGLE_BLOCK:
+ case MMC_READ_MULTIPLE_BLOCK:
+ case MMC_WRITE_BLOCK:
+ case MMC_WRITE_MULTIPLE_BLOCK:
+ case MMC_SEND_EXT_CSD:
+ case MMC_GEN_CMD:
+ case MMC_SLEEP_AWAKE:
+ case MMC_SWITCH:
+ case MMC_SET_WRITE_PROT:
+ case MMC_CLR_WRITE_PROT:
+ case MMC_SEND_WRITE_PROT:
+ case MMC_ERASE:
+ case MMC_SEND_TUNING_BLOCK_HS200:
+ xfer_flag = true;
+ break;
+ default:
+ xfer_flag = false;
+ }
+
+ host->int_waiting = &dw_mci_wait;
+ end = jiffies + msecs_to_jiffies(DW_MCI_TIMEOUT_Ms);
+ mod_timer(&host->timer, end);
+
+ if (host->int_waiting) {
+ dw_mci_clr_signal_int(host);
+ dw_mci_clr_int(host);
+
+ /*command with data, r1b case*/
+ if (xfer_flag == 1)
+ dw_mci_en_xfer_int(host);
+ else
+ dw_mci_en_cd_int(host);
+
+ /*If we use cmd23, we cannot send auto stop command*/
+ if (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
+ cmd->opcode == MMC_READ_MULTIPLE_BLOCK) {
+ if (host->is_sbc) {
+ mcq_writew(host, XFER_MODE_R,
+ mcq_readw(host, XFER_MODE_R) & ~BIT(SDMMC_AUTO_CMD_ENABLE));
+ host->is_sbc = 0;
+ }
+ }
+
+ host->opcode = cmd->opcode;
+ host->arg = cmd->arg;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ mcq_writew(host, CMD_R, cmd_flags);
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+
+ wait_for_completion(host->int_waiting);
+
+ if (xfer_flag == 1) {
+ ret = readl_poll_timeout(host->regs + SDMMC_NORMAL_INT_STAT_R, status,
+ (status & SDMMC_XFER_COMPLETE) == SDMMC_XFER_COMPLETE
+ , 10, DW_MCI_TIMEOUT);
+ if (ret) {
+ /*error interrupt detected*/
+ if ((mcq_readw(host, NORMAL_INT_STAT_R) & SDMMC_ERR_INTERRUPT)
+ && (host->tuning == 1))
+ dev_info(host->dev, "Tuning error ... keep tuning\n");
+ else
+ dev_err(host->dev, "Timeout waiting xfer complete, status = 0x%x\n",
+ (status & 0xffff));
+ }
+ } else {
+ ret = readl_poll_timeout(host->regs + SDMMC_NORMAL_INT_STAT_R, status,
+ (status & SDMMC_CMD_COMPLETE) == SDMMC_CMD_COMPLETE,
+ 10, DW_MCI_TIMEOUT);
+ if (ret)
+ dev_err(host->dev, "Timeout waiting cmd request complete\n");
+ }
+
+ if (host->normal_interrupt & SDMMC_ERR_INTERRUPT) {
+ if (host->tuning != 1)
+ dw_mci_cqe_regs_show(host, cmd, cmd_flags);
+ err = -1;
+ }
+ }
+
+ return err;
+}
+
+static void dw_mci_cqe_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
+{
+
+ struct mmc_command stop;
+ u32 cmdr;
+ /*Stop command only use after data command*/
+ if (!cmd->data)
+ return;
+
+ memset(&stop, 0, sizeof(struct mmc_command));
+
+ if (cmd->opcode == MMC_READ_SINGLE_BLOCK ||
+ cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
+ cmd->opcode == MMC_WRITE_BLOCK ||
+ cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
+ cmd->opcode == MMC_SEND_TUNING_BLOCK ||
+ cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200) {
+ stop.opcode = MMC_STOP_TRANSMISSION;
+ stop.arg = 0;
+ stop.flags = MMC_RSP_R1 | MMC_CMD_AC;
+ } else if (cmd->opcode == SD_IO_RW_EXTENDED) {
+ stop.opcode = SD_IO_RW_DIRECT;
+ stop.arg |= (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
+ ((cmd->arg >> 28) & 0x7);
+ stop.flags = MMC_RSP_SPI_R5 | MMC_RSP_R5 | MMC_CMD_AC;
+ } else {
+ return;
+ }
+
+ cmdr = (stop.opcode << 8) | SDMMC_RESP_LEN_48 |
+ SDMMC_CMD_CHK_RESP_CRC | SDMMC_CMD_IDX_CHK_ENABLE;
+ cmdr |= (SDMMC_ABORT_CMD << 6);
+ mcq_writew(host, XFER_MODE_R, 0);
+ mcq_writel(host, ARGUMENT_R, stop.arg);
+ dw_mci_cqe_start_command(host, &stop, cmdr);
+}
+
+static int dw_mci_cqe_wait_status(struct dw_mci *host, struct mmc_command *cmd, u32 *status)
+{
+ struct mmc_command wait;
+ u32 cmdr;
+ u32 cur_state;
+ unsigned long timeend;
+ int err = 0;
+
+ /* According to Synopsys userguide, we need to send wait command after
+ * stop cmd to check current status
+ */
+
+ wait = host->stat_ready;
+ memset(&wait, 0, sizeof(struct mmc_command));
+
+ timeend = jiffies + msecs_to_jiffies(500);
+ do {
+ wait.opcode = MMC_SEND_STATUS;
+ wait.arg = 1 << 16;
+ wait.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC;
+ wait.data = NULL;
+ cmdr = (wait.opcode << 8) | SDMMC_RESP_LEN_48 |
+ SDMMC_CMD_CHK_RESP_CRC | SDMMC_CMD_IDX_CHK_ENABLE;
+
+ mcq_writew(host, XFER_MODE_R, 0);
+ mcq_writel(host, ARGUMENT_R, wait.arg);
+ err = dw_mci_cqe_start_command(host, &wait, cmdr);
+ if (err) {
+ dw_mci_cqe_reset(host);
+ break;
+ }
+
+ dw_mci_cqe_read_rsp(host, &wait, wait.resp);
+ *status = wait.resp[0];
+ cur_state = R1_CURRENT_STATE(wait.resp[0]);
+ err = -DW_MCI_NOT_READY;
+ if (cur_state == R1_STATE_TRAN) {
+ if (wait.resp[0] & R1_READY_FOR_DATA) {
+ err = 0;
+ break;
+ }
+ }
+ } while (time_before(jiffies, timeend));
+
+ return err;
+}
+
+static void dw_mci_cqe_stop_dma(struct dw_mci *host, struct mmc_data *data)
+{
+ u32 dir = 0;
+
+ if (data->flags & MMC_DATA_READ)
+ dir = DMA_FROM_DEVICE;
+ else
+ dir = DMA_TO_DEVICE;
+
+ dma_unmap_sg(mmc_dev(host->slot->mmc), data->sg, data->sg_len, dir);
+ host->sg = NULL;
+}
+
+static void dw_mci_cqe_prepare_desc64(struct dw_mci *host, struct mmc_data *data,
+ struct scatterlist *sg)
+{
+ dev_info(host->dev, "Currently, the 64bit DMA mode is not implemented yet.\n");
+}
+
+
+static void dw_mci_cqe_prepare_desc32(struct dw_mci *host, struct mmc_data *data,
+ struct scatterlist *sg)
+{
+ u32 blk_cnt, cur_blk_cnt, remain_blk_cnt;
+ u32 tmp_val;
+ u32 *desc_base = host->sg_cpu;
+ u32 dma_len = 0;
+ u32 dma_addr;
+ u32 i;
+ unsigned int begin, end;
+
+ for (i = 0; i < host->dma_nents; i++, sg++) {
+ dma_len = sg_dma_len(sg);
+
+ /*blk_cnt must be the multiple of 512(0x200)*/
+ if (dma_len < SZ_512)
+ blk_cnt = 1;
+ else
+ blk_cnt = dma_len >> 9;
+
+ remain_blk_cnt = blk_cnt;
+ dma_addr = sg_dma_address(sg);
+
+ while (remain_blk_cnt) {
+ /*DW_MCI_MAX_SCRIPT_BLK is the max
+ * for each descriptor record
+ */
+ if (remain_blk_cnt > DW_MCI_MAX_SCRIPT_BLK)
+ cur_blk_cnt = DW_MCI_MAX_SCRIPT_BLK;
+ else
+ cur_blk_cnt = remain_blk_cnt;
+
+ /* In Synopsys DesignWare Databook Page 84,
+ * They mentioned the DMA 128MB restriction
+ */
+ begin = dma_addr / SZ_128M;
+ end = (dma_addr + cur_blk_cnt * SZ_512) / SZ_128M;
+
+ /*If begin and end in the different 128MB memory zone*/
+ if (begin != end)
+ cur_blk_cnt = (end * SZ_128M - dma_addr) / SZ_512;
+
+ if (dma_len < SZ_512)
+ tmp_val = ((dma_len) << 16) | VALID(0x1) | ACT(0x4);
+ else
+ tmp_val = ((cur_blk_cnt & 0x7f) << 25) | VALID(0x1) | ACT(0x4);
+
+ /*Last descriptor*/
+ if (i == host->dma_nents - 1 && remain_blk_cnt == cur_blk_cnt)
+ tmp_val |= END(0x1);
+
+ desc_base[0] = tmp_val;
+ desc_base[1] = dma_addr;
+
+ dma_addr = dma_addr + (cur_blk_cnt << 9);
+ remain_blk_cnt -= cur_blk_cnt;
+ desc_base += 2;
+ }
+ }
+}
+
+static int dw_mci_cqe_get_cd(struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ int gpio_cd = mmc_gpio_get_cd(mmc);
+ int present = -1;
+
+ /* Use platform get_cd function, else try onboard card detect */
+ if (((mmc->caps & MMC_CAP_NEEDS_POLL)
+ || !mmc_card_is_removable(mmc))) {
+ present = 1;
+
+ if (!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
+ if (mmc->caps & MMC_CAP_NEEDS_POLL) {
+ dev_info(&mmc->class_dev,
+ "card is polling.\n");
+ } else {
+ dev_info(&mmc->class_dev,
+ "card is non-removable.\n");
+ }
+ set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ }
+
+ return present;
+ } else if (gpio_cd >= 0) {
+ present = gpio_cd;
+ } else {
+ /*SD card detect using IP regs is todo*/
+ dev_err(&mmc->class_dev, "SD card detect using IP regs is ToDo.\n");
+ }
+
+ spin_lock_bh(&host->lock);
+
+ if (present && !test_and_set_bit(DW_MMC_CARD_PRESENT, &slot->flags))
+ dev_dbg(&mmc->class_dev, "card is present\n");
+ else if (!present &&
+ !test_and_clear_bit(DW_MMC_CARD_PRESENT, &slot->flags))
+ dev_dbg(&mmc->class_dev, "card is not present\n");
+
+ spin_unlock_bh(&host->lock);
+
+ return present;
+}
+
+static void dw_mci_cqe_submit_data_dma(struct dw_mci *host)
+{
+ if (host->dma_64bit_address == 1)
+ dw_mci_cqe_prepare_desc64(host, host->data, host->sg);
+ else
+ dw_mci_cqe_prepare_desc32(host, host->data, host->sg);
+
+}
+
+static void dw_mci_cqe_submit_data(struct dw_mci *host, struct mmc_data *data)
+{
+ u32 dir = 0;
+
+ host->sg = NULL;
+ host->data = data;
+
+ if (data->flags & MMC_DATA_READ)
+ dir = DMA_FROM_DEVICE;
+ else
+ dir = DMA_TO_DEVICE;
+
+ host->dma_nents = dma_map_sg(mmc_dev(host->slot->mmc),
+ data->sg, data->sg_len, dir);
+ host->sg = data->sg;
+
+ host->using_dma = 1;
+
+ dw_mci_cqe_submit_data_dma(host);
+}
+
+static void dw_mci_cqe_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
+{
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ unsigned int clock = slot->clock;
+ u32 div = 0;
+
+ slot->mmc->actual_clock = 0;
+
+ if (clock != host->current_speed || force_clkinit) {
+ div = host->bus_hz / clock;
+ if (host->bus_hz % clock)
+ div += 1;
+
+ if (clock != slot->__clk_old) {
+ /* Silent the verbose log if calling from PM context */
+ dev_info(&slot->mmc->class_dev,
+ "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
+ slot->id, host->bus_hz, clock, host->bus_hz / div, div);
+ }
+
+ slot->__clk_old = clock;
+ slot->mmc->actual_clock = host->bus_hz / div;
+
+ if (drv_data && drv_data->set_ios)
+ drv_data->set_ios(slot, &slot->mmc->ios);
+ }
+}
+
+
+static void dw_mci_cqe_err_handle(struct dw_mci *host, struct mmc_command *cmd)
+{
+ u32 status = 0;
+ int pstat_rty = 0;
+ int ret;
+ int err = 0;
+ int rty_cnt = 0;
+
+ do {
+ mcq_writew(host, ERROR_INT_STAT_R,
+ mcq_readw(host, ERROR_INT_STAT_R) & 0xffff);
+ /*synchronous abort: stop host dma*/
+ mcq_writeb(host, BGAP_CTRL_R, SDMMC_STOP_BG_REQ);
+
+ ret = readl_poll_timeout(host->regs + SDMMC_NORMAL_INT_STAT_R, status,
+ (status & SDMMC_XFER_COMPLETE) == SDMMC_XFER_COMPLETE, 10, DW_MCI_TIMEOUT);
+ if (ret) {
+ if ((mcq_readw(host, NORMAL_INT_STAT_R) & SDMMC_ERR_INTERRUPT) != 0)
+ dev_info(host->dev, "status = 0x%x\n", (status & 0xffff));
+ else
+ dev_err(host->dev, "Timeout waiting err_handle xfer complete\n");
+ }
+
+ mcq_writew(host, NORMAL_INT_STAT_R, SDMMC_XFER_COMPLETE);
+
+ if (cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200) {
+ dw_mci_cqe_prep_stop_abort(host, cmd);
+ mdelay(1);
+
+ err = dw_mci_cqe_wait_status(host, cmd, &status);
+ rty_cnt++;
+ if (rty_cnt > 100) {
+ if (err == -DW_MCI_NOT_READY) {
+ dev_err(host->dev, "status check failed, err = %d, status = 0x%x\n",
+ err, status);
+ break;
+ }
+ }
+ } else {
+ break;
+ }
+
+ mcq_writeb(host, SW_RST_R, SDMMC_RST_CMD | SDMMC_RST_DAT);
+
+ ret = readl_poll_timeout(host->regs + SDMMC_CLK_CTRL_R, status,
+ (status & SW_RST_BOTH_DONE) == 0x0, 10, DW_MCI_TIMEOUT);
+ ret = readl_poll_timeout(host->regs + SDMMC_PSTATE_REG, status,
+ (status & 0x3) == 0x0, 10, DW_MCI_TIMEOUT);
+ if (ret)
+ dev_err(host->dev, "Waiting error handling done timeout\n");
+
+ udelay(40);
+
+ pstat_rty++;
+ if (pstat_rty > 5000) {
+ dev_err(host->dev, "wait pstate register data line ready timeout\n");
+ break;
+ }
+ } while ((mcq_readl(host, PSTATE_REG) & 0xf00000) != 0xf00000 ||
+ (mcq_readl(host, PSTATE_REG) & 0xf0) != 0xf0);
+}
+
+static void dw_mci_cqe_send_stop_abort(struct dw_mci *host,
+ struct dw_mci_slot *slot,
+ struct mmc_command *cmd)
+{
+ dw_mci_cqe_reset(host);
+
+ if (cmd->data)
+ dw_mci_cqe_err_handle(host, cmd);
+ else
+ return;
+}
+
+static u32 dw_mci_cqe_prepare_data_flags(struct mmc_command *cmd)
+{
+ u32 dataflags;
+ int read_flag = 1;
+ int mul_blk_flag = 0;
+ int auto_stop_flag = 0;
+
+ if (cmd->opcode == MMC_WRITE_BLOCK ||
+ cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
+ cmd->opcode == MMC_LOCK_UNLOCK ||
+ (cmd->opcode == MMC_GEN_CMD && cmd->arg == 0))
+ read_flag = 0;
+
+ if (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
+ cmd->opcode == MMC_READ_MULTIPLE_BLOCK) {
+ mul_blk_flag = 1;
+ auto_stop_flag = 1;
+ }
+
+ dataflags = (mul_blk_flag << SDMMC_MULTI_BLK_SEL) |
+ (read_flag << SDMMC_DATA_XFER_DIR) |
+ (auto_stop_flag << SDMMC_AUTO_CMD_ENABLE) |
+ (SDMMC_BLOCK_COUNT_ENABLE) |
+ (SDMMC_DMA_ENABLE);
+
+ return dataflags;
+}
+
+static int dw_mci_cqe_command_complete(struct dw_mci *host, u16 interrupt,
+ int *cmd_error)
+{
+ if (interrupt & (SDMMC_CMD_IDX_ERR | SDMMC_CMD_END_BIT_ERR
+ | SDMMC_CMD_CRC_ERR)) {
+ if (host->tuning)
+ *cmd_error = -TUNING_ERR;
+ else
+ *cmd_error = -EILSEQ;
+ } else if (interrupt & SDMMC_CMD_TOUT_ERR) {
+ if (host->tuning)
+ *cmd_error = -TUNING_ERR;
+ else
+ *cmd_error = -ETIMEDOUT;
+ } else {
+ *cmd_error = 0;
+ }
+
+ return *cmd_error;
+}
+
+static int dw_mci_cqe_data_complete(struct dw_mci *host, u16 interrupt,
+ int *data_error)
+{
+ if (interrupt & (SDMMC_DATA_END_BIT_ERR | SDMMC_DATA_CRC_ERR)) {
+ if (host->tuning)
+ *data_error = -TUNING_ERR;
+ else
+ *data_error = -EILSEQ;
+ } else if (interrupt & SDMMC_DATA_TOUT_ERR) {
+ if (host->tuning)
+ *data_error = -TUNING_ERR;
+ else
+ *data_error = -ETIMEDOUT;
+ } else if (interrupt & SDMMC_ADMA_ERR) {
+ *data_error = -EIO;
+ } else {
+ *data_error = 0;
+ }
+
+ return *data_error;
+}
+
+static void __dw_mci_cqe_start_request(struct dw_mci *host,
+ struct dw_mci_slot *slot,
+ struct mmc_command *cmd)
+{
+ struct mmc_data *data;
+ u32 cmdflags;
+ u32 dataflags;
+ int ret = 0;
+
+ data = cmd->data;
+
+ if (data) {
+ mcq_writew(host, BLOCKCOUNT_R, data->blocks);
+ mcq_writel(host, BLOCKSIZE_R, data->blksz);
+ mcq_writel(host, ADMA_SA_LOW_R, host->sg_dma);
+
+ dataflags = dw_mci_cqe_prepare_data_flags(cmd);
+
+ mcq_writew(host, XFER_MODE_R, dataflags);
+ } else {
+ if (cmd->opcode == MMC_SET_BLOCK_COUNT)
+ host->is_sbc = 1;
+ else
+ host->is_sbc = 0;
+
+ mcq_writew(host, XFER_MODE_R, 0);
+ }
+
+ mcq_writel(host, ARGUMENT_R, cmd->arg);
+
+ cmdflags = dw_mci_cqe_prepare_command(slot->mmc, cmd);
+
+ if (data) {
+ data->bytes_xfered = 0;
+ if (host->use_dma == TRANS_MODE_DMA) {
+ dw_mci_cqe_submit_data(host, data);
+ wmb(); /* drain writebuffer */
+ } else {
+ /*Using PIO mode*/
+ dev_err(host->dev, "pio mode is not supported currently\n");
+ }
+ }
+
+ ret = dw_mci_cqe_start_command(host, cmd, cmdflags);
+
+ if (ret == 0) {
+ dw_mci_cqe_read_rsp(host, cmd, cmd->resp);
+
+ if (data)
+ data->bytes_xfered += (data->blocks * data->blksz);
+ }
+
+ dw_mci_cqe_command_complete(host, host->error_interrupt, &cmd->error);
+ if (data) {
+ dw_mci_cqe_data_complete(host, host->error_interrupt, &data->error);
+ if (host->use_dma == TRANS_MODE_DMA)
+ dw_mci_cqe_stop_dma(host, data);
+ else {
+ /*Using PIO mode*/
+ dev_err(host->dev, "pio mode is not supported currently\n");
+ }
+ }
+
+ if (ret != 0)
+ dw_mci_cqe_send_stop_abort(host, slot, cmd);
+
+ if (cmd->opcode == SD_SWITCH_VOLTAGE) {
+ /*
+ * If cmd11 needs to be dealt with specially, put in here.
+ */
+ }
+}
+
+static void dw_mci_cqe_start_request(struct dw_mci *host,
+ struct dw_mci_slot *slot)
+{
+ struct mmc_request *mrq = slot->mrq;
+
+ if (mrq->sbc)
+ __dw_mci_cqe_start_request(host, slot, mrq->sbc);
+
+ if (mrq->cmd)
+ __dw_mci_cqe_start_request(host, slot, mrq->cmd);
+}
+
+static void dw_mci_cqe_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ WARN_ON(slot->mrq);
+
+ /*
+ * The check for card presence and queueing of the request must be
+ * atomic, otherwise the card could be removed in between and the
+ * request wouldn't fail until another card was inserted.
+ */
+
+ if (!dw_mci_cqe_get_cd(mmc)) {
+ mrq->cmd->error = -ENOMEDIUM;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+
+ down_write(&host->cr_rw_sem);
+
+ slot->mrq = mrq;
+ host->mrq = mrq;
+
+ dw_mci_cqe_start_request(host, slot);
+
+ tasklet_schedule(&host->tasklet);
+
+ up_write(&host->cr_rw_sem);
+}
+
+static void dw_mci_cqe_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
+
+ switch (ios->timing) {
+ case MMC_TIMING_MMC_HS400:
+ mcq_writew(host, HOST_CTRL2_R,
+ (mcq_readw(host, HOST_CTRL2_R)
+ & SDMMC_UHS_MODE_SEL_MASK) | SDMMC_HS400);
+ break;
+ case MMC_TIMING_MMC_HS200:
+ mcq_writew(host, HOST_CTRL2_R,
+ (mcq_readw(host, HOST_CTRL2_R)
+ & SDMMC_UHS_MODE_SEL_MASK) | SDMMC_HS200);
+ break;
+ case MMC_TIMING_MMC_HS:
+ mcq_writew(host, HOST_CTRL2_R,
+ (mcq_readw(host, HOST_CTRL2_R)
+ & SDMMC_UHS_MODE_SEL_MASK) | SDMMC_SDR);
+ break;
+ default:
+ /*MMC_TIMING_LEGACY case*/
+ mcq_writew(host, HOST_CTRL2_R,
+ (mcq_readw(host, HOST_CTRL2_R)
+ & SDMMC_UHS_MODE_SEL_MASK) | SDMMC_LEGACY);
+ }
+
+ slot->clock = ios->clock;
+
+ if (drv_data && drv_data->set_ios)
+ drv_data->set_ios(slot, ios);
+
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_4:
+ mcq_writeb(host, HOST_CTRL1_R,
+ (mcq_readb(host, HOST_CTRL1_R) &
+ (SDMMC_EXT_DAT_XFER_MASK & SDMMC_DAT_XFER_WIDTH_MASK))
+ |SDMMC_BUS_WIDTH_4);
+ break;
+ case MMC_BUS_WIDTH_8:
+ mcq_writeb(host, HOST_CTRL1_R,
+ (mcq_readb(host, HOST_CTRL1_R) &
+ SDMMC_EXT_DAT_XFER_MASK) | SDMMC_BUS_WIDTH_8);
+ break;
+ default:
+ /* set default 1 bit mode */
+ mcq_writeb(host, HOST_CTRL1_R,
+ (mcq_readb(host, HOST_CTRL1_R) &
+ (SDMMC_EXT_DAT_XFER_MASK &
+ SDMMC_DAT_XFER_WIDTH_MASK)) | SDMMC_BUS_WIDTH_1);
+ }
+}
+
+static int dw_mci_cqe_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ if (drv_data && drv_data->switch_voltage)
+ return drv_data->switch_voltage(mmc, ios);
+
+ return 0;
+}
+
+static int dw_mci_cqe_get_ro(struct mmc_host *mmc)
+{
+ int read_only = 0;
+ int gpio_ro;
+
+ gpio_ro = mmc_gpio_get_ro(mmc);
+
+ /* Use platform get_ro function, else try on board write protect */
+ if (gpio_ro >= 0)
+ read_only = gpio_ro;
+ else
+ /*Need to read the IP register to judge if ro*/
+ dev_err(&mmc->class_dev, "IP get_ro feature is not implemented currently.\n");
+
+ dev_dbg(&mmc->class_dev, "card is %s\n",
+ read_only ? "read-only" : "read-write");
+
+ return read_only;
+}
+
+static int dw_mci_cqe_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int err = -EINVAL;
+
+ if (drv_data && drv_data->execute_tuning)
+ err = drv_data->execute_tuning(slot, opcode);
+ return err;
+
+}
+
+static int dw_mci_cqe_prepare_hs400_tuning(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ if (drv_data && drv_data->prepare_hs400_tuning)
+ return drv_data->prepare_hs400_tuning(host, ios);
+
+ return 0;
+}
+
+static void dw_mci_cqe_hs400_complete(struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ if (drv_data && drv_data->hs400_complete)
+ drv_data->hs400_complete(mmc);
+}
+
+static void dw_mci_cqe_init_card(struct mmc_host *mmc, struct mmc_card *card)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ /*
+ * Add any quirks for this synopsys IP here or
+ * deal with something special for some specific
+ * vendors' SOC platform by calling drv_data->init_card().
+ */
+ if (drv_data && drv_data->init_card)
+ drv_data->init_card(mmc, card);
+}
+
+static const struct mmc_host_ops dw_mci_ops = {
+ .request = dw_mci_cqe_request,
+ .set_ios = dw_mci_cqe_set_ios,
+ .get_ro = dw_mci_cqe_get_ro,
+ .get_cd = dw_mci_cqe_get_cd,
+ .execute_tuning = dw_mci_cqe_execute_tuning,
+ .start_signal_voltage_switch = dw_mci_cqe_switch_voltage,
+ .init_card = dw_mci_cqe_init_card,
+ .prepare_hs400_tuning = dw_mci_cqe_prepare_hs400_tuning,
+ .hs400_complete = dw_mci_cqe_hs400_complete,
+};
+
+static void dw_mci_cqe_tasklet_func(unsigned long priv)
+{
+ struct dw_mci *host = (struct dw_mci *)priv;
+ struct mmc_host *prev_mmc = host->slot->mmc;
+ struct mmc_request *mrq;
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+
+ host->cmd = NULL;
+ host->data = NULL;
+ mrq = host->mrq;
+ host->slot->mrq = NULL;
+ host->mrq = NULL;
+
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+
+ mmc_request_done(prev_mmc, mrq);
+}
+
+static irqreturn_t dw_mci_cqe_interrupt(int irq, void *dev_id)
+{
+ struct dw_mci *host = dev_id;
+ struct mmc_host *mmc = host->slot->mmc;
+ struct cqhci_host *cq_host = NULL;
+ int cmd_error = 0, data_error = 0;
+
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE))
+ cq_host = mmc->cqe_private;
+
+ dw_mci_get_int(host);
+
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE)) {
+ if (mmc->cqe_on == false && cq_host->activated == false)
+ dw_mci_clr_signal_int(host);
+ } else {
+ dw_mci_clr_signal_int(host);
+ }
+ /*if run the cmdq mode*/
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE) &&
+ mmc->cqe_on == true && cq_host->activated == true) {
+ if (host->normal_interrupt & SDMMC_ERR_INTERRUPT) {
+ dev_err(host->dev, "cmdq error: interrupt status=%08x, error interrupt=0x%08x, CQIS=0x%x, CQTCN=0x%x\n",
+ host->normal_interrupt, host->error_interrupt,
+ readl(host->cqe->mmio + CQHCI_IS),
+ readl(host->cqe->mmio + CQHCI_TCN));
+
+ dw_mci_cqe_command_complete(host, host->error_interrupt, &cmd_error);
+ dw_mci_cqe_data_complete(host, host->error_interrupt, &data_error);
+ }
+ cqhci_irq(mmc, (u32)(host->normal_interrupt), cmd_error, data_error);
+ dw_mci_clr_int(host);
+
+ return IRQ_HANDLED;
+ }
+
+ if (host->int_waiting) {
+ del_timer(&host->timer);
+ complete(host->int_waiting);
+ }
+
+ return IRQ_HANDLED;
+
+}
+
+static void dw_mci_cqe_setup(struct dw_mci *host)
+{
+ mcq_writeb(host, SW_RST_R, (SDMMC_RST_ALL|SDMMC_RST_CMD|SDMMC_RST_DAT));
+ mcq_writeb(host, TOUT_CTRL_R, 0xe);
+ mcq_writew(host, HOST_CTRL2_R, SDMMC_HOST_VER4_ENABLE|SDMMC_SIGNALING_EN);
+ mcq_writew(host, NORMAL_INT_STAT_EN_R, 0xffff);
+ mcq_writew(host, ERROR_INT_STAT_EN_R, SDMMC_ALL_ERR_STAT_EN);
+ /*Card detect will be enabled in the last*/
+ mcq_writew(host, NORMAL_INT_SIGNAL_EN_R, (~(SDMMC_CARD_INSERTION_SIGNAL_EN |
+ SDMMC_CARD_REMOVAL_SIGNAL_EN | SDMMC_CARD_INTERRUPT_SIGNAL_EN) & 0xffff));
+ mcq_writew(host, ERROR_INT_SIGNAL_EN_R, SDMMC_ALL_ERR_SIGNAL_EN);
+ mcq_writeb(host, CTRL_R, SDMMC_RST_N_OE|SDMMC_RST_N|SDMMC_CARD_IS_EMMC);
+ mcq_writeb(host, HOST_CTRL1_R,
+ (mcq_readb(host, HOST_CTRL1_R)&0xe7) | (SDMMC_ADMA2_32 << SDMMC_DMA_SEL));
+ mcq_writeb(host, MSHC_CTRL_R, mcq_readb(host, MSHC_CTRL_R) & (~SDMMC_CMD_CONFLICT_CHECK));
+ mcq_writew(host, CLK_CTRL_R, mcq_readw(host, CLK_CTRL_R)|SDMMC_INTERNAL_CLK_EN);
+}
+
+static int dw_mci_cqe_init_slot_caps(struct dw_mci_slot *slot)
+{
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ struct mmc_host *mmc = slot->mmc;
+ int ctrl_id;
+
+ if (host->pdata->caps)
+ mmc->caps = host->pdata->caps;
+
+ if (host->pdata->pm_caps)
+ mmc->pm_caps = host->pdata->pm_caps;
+
+ if (host->dev->of_node) {
+ ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
+ if (ctrl_id < 0)
+ ctrl_id = 0;
+ } else {
+ ctrl_id = to_platform_device(host->dev)->id;
+ }
+
+ if (drv_data && drv_data->caps) {
+ if (ctrl_id >= drv_data->num_caps) {
+ dev_err(host->dev, "invalid controller id %d\n",
+ ctrl_id);
+ return -EINVAL;
+ }
+ mmc->caps |= drv_data->caps[ctrl_id];
+ }
+
+ if (host->pdata->caps2)
+ mmc->caps2 = host->pdata->caps2;
+
+ mmc->f_min = DW_MCI_FREQ_MIN;
+ if (!mmc->f_max)
+ mmc->f_max = DW_MCI_FREQ_MAX;
+
+ /* Process SDIO IRQs through the sdio_irq_work. */
+ if (mmc->caps & MMC_CAP_SDIO_IRQ)
+ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
+
+ return 0;
+}
+
+static int dw_mci_cqe_init_slot(struct dw_mci *host)
+{
+ struct mmc_host *mmc;
+ struct dw_mci_slot *slot;
+ int ret;
+
+ mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
+ if (!mmc)
+ return -ENOMEM;
+
+ slot = mmc_priv(mmc);
+ slot->id = 0;
+ slot->sdio_id = host->sdio_id0 + slot->id;
+ slot->mmc = mmc;
+ slot->host = host;
+ host->slot = slot;
+
+ mmc->ops = &dw_mci_ops;
+
+ /*if there are external regulators, get them*/
+ ret = mmc_regulator_get_supply(mmc);
+ if (ret)
+ goto err_host_allocated;
+
+ if (!mmc->ocr_avail)
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+ dev_info(host->dev, "regulator support volage ocr_avail=0x%x\n",
+ mmc->ocr_avail);
+
+ ret = mmc_of_parse(mmc);
+ if (ret)
+ goto err_host_allocated;
+
+ ret = dw_mci_cqe_init_slot_caps(slot);
+ if (ret)
+ goto err_host_allocated;
+
+ /* Useful defaults if platform data is unset. */
+ if (host->use_dma == TRANS_MODE_DMA) {
+ mmc->max_segs = 256;
+ mmc->max_blk_size = 512;
+ mmc->max_seg_size = 0x1000;
+ mmc->max_req_size = mmc->max_seg_size * mmc->max_segs;
+ mmc->max_blk_count = mmc->max_req_size / 512;
+ } else {
+ dev_info(host->dev, "dw-mmc-cqe pio mode is ToDo.\n");
+ /* To DO, TRANS_MODE_PIO */
+ }
+
+ dw_mci_cqe_get_cd(mmc);
+
+ ret = mmc_add_host(mmc);
+ if (ret)
+ goto err_host_allocated;
+
+ return 0;
+
+err_host_allocated:
+ mmc_free_host(mmc);
+ return ret;
+}
+
+static void dw_mci_cqe_cleanup_slot(struct dw_mci_slot *slot)
+{
+ /* Debugfs stuff is cleaned up by mmc core */
+ mmc_remove_host(slot->mmc);
+ slot->host->slot = NULL;
+ mmc_free_host(slot->mmc);
+}
+
+static void dw_mci_cqe_init_dma(struct dw_mci *host)
+{
+ host->use_dma = TRANS_MODE_DMA;
+
+ /* Determine which DMA interface to use */
+ /* using 32bit DMA by default,
+ * user can modify this setting by drv_data->init()
+ */
+ if (host->use_dma == TRANS_MODE_DMA) {
+ host->dma_64bit_address = 0;
+ dev_info(host->dev, "IDMAC supports 32-bit address mode.\n");
+ }
+
+ /* Alloc memory for sg translation */
+ host->sg_cpu = dma_alloc_coherent(host->dev,
+ DW_MCI_DESC_LEN,
+ &host->sg_dma, GFP_KERNEL);
+ if (!host->sg_cpu) {
+ dev_err(host->dev,
+ "%s: could not alloc DMA memory\n",
+ __func__);
+ goto no_dma;
+ }
+
+ return;
+
+no_dma:
+ dev_info(host->dev, "Using PIO mode.\n");
+ host->use_dma = TRANS_MODE_PIO;
+}
+
+#ifdef CONFIG_OF
+static struct dw_mci_board *dw_mci_cqe_parse_dt(struct dw_mci *host)
+{
+ struct dw_mci_board *pdata;
+ struct device *dev = host->dev;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int ret;
+ u32 clock_frequency;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM);
+
+ /* find reset controller when exist */
+ pdata->rstc = devm_reset_control_get_optional(dev, "reset");
+ if (IS_ERR(pdata->rstc)) {
+ if (PTR_ERR(pdata->rstc) == -EPROBE_DEFER)
+ return ERR_PTR(-EPROBE_DEFER);
+ }
+
+ device_property_read_u32(dev, "card-detect-delay",
+ &pdata->detect_delay_ms);
+
+ if (!device_property_read_u32(dev, "clock-frequency", &clock_frequency))
+ pdata->bus_hz = clock_frequency;
+
+ if (drv_data && drv_data->parse_dt) {
+ ret = drv_data->parse_dt(host);
+ if (ret)
+ return ERR_PTR(ret);
+ }
+
+ return pdata;
+}
+
+#else /* CONFIG_OF */
+static struct dw_mci_board *dw_mci_cqe_parse_dt(struct dw_mci *host)
+{
+ return ERR_PTR(-EINVAL);
+}
+#endif /* CONFIG_OF */
+
+static void dw_mci_cqe_cto_timer(struct timer_list *t)
+{
+ struct dw_mci *host = from_timer(host, t, timer);
+
+ if (host->int_waiting) {
+ dev_err(host->dev, "fired, opcode=%d, arg=0x%x, irq status=0x%x, err irq=0x%x, auto err irq=0x%x\n",
+ host->opcode, host->arg,
+ host->normal_interrupt, host->error_interrupt,
+ host->auto_error_interrupt);
+
+ dw_mci_clr_signal_int(host);
+ dw_mci_get_int(host);
+
+ complete(host->int_waiting);
+ }
+}
+
+static void dw_mci_cqhci_init(struct dw_mci *host)
+{
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE)) {
+ host->cqe = cqhci_pltfm_init(host->pdev);
+ if (PTR_ERR(host->cqe) == -EINVAL ||
+ PTR_ERR(host->cqe) == -ENOMEM ||
+ PTR_ERR(host->cqe) == -EBUSY) {
+ dev_err(host->dev, "Unable to get the cmdq related attribute,err = %ld\n",
+ PTR_ERR(host->cqe));
+ host->cqe = 0;
+ host->pdata->caps2 &= ~(MMC_CAP2_CQE|MMC_CAP2_CQE_DCMD);
+ } else {
+ host->cqe->ops = &dw_mci_cqhci_host_ops;
+ cqhci_init(host->cqe, host->slot->mmc, 0);
+ }
+ }
+}
+
+int dw_mci_cqe_probe(struct dw_mci *host)
+{
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int ret = 0;
+
+ if (!host->pdata) {
+ host->pdata = dw_mci_cqe_parse_dt(host);
+ if (PTR_ERR(host->pdata) == -EPROBE_DEFER) {
+ return -EPROBE_DEFER;
+ } else if (IS_ERR(host->pdata)) {
+ dev_err(host->dev, "platform data not available\n");
+ return -EINVAL;
+ }
+ }
+
+ host->biu_clk = devm_clk_get(host->dev, "biu");
+ if (IS_ERR(host->biu_clk)) {
+ dev_dbg(host->dev, "biu clock not available\n");
+ } else {
+ ret = clk_prepare_enable(host->biu_clk);
+ if (ret) {
+ dev_err(host->dev, "failed to enable biu clock\n");
+ return ret;
+ }
+ }
+
+ host->ciu_clk = devm_clk_get(host->dev, "ciu");
+ if (IS_ERR(host->ciu_clk)) {
+ dev_dbg(host->dev, "ciu clock not available\n");
+ host->bus_hz = host->pdata->bus_hz;
+ } else {
+ ret = clk_prepare_enable(host->ciu_clk);
+ if (ret) {
+ dev_err(host->dev, "failed to enable ciu clock\n");
+ goto err_clk_biu;
+ }
+
+ if (host->pdata->bus_hz) {
+ ret = clk_set_rate(host->ciu_clk, host->pdata->bus_hz);
+ if (ret)
+ dev_warn(host->dev,
+ "Unable to set bus rate to %uHz\n",
+ host->pdata->bus_hz);
+ }
+ host->bus_hz = clk_get_rate(host->ciu_clk);
+ }
+
+ if (!host->bus_hz) {
+ dev_err(host->dev,
+ "Platform data must supply bus speed\n");
+ ret = -ENODEV;
+ goto err_clk_ciu;
+ }
+
+ if (!IS_ERR(host->pdata->rstc)) {
+ reset_control_assert(host->pdata->rstc);
+ usleep_range(10, 50);
+ reset_control_deassert(host->pdata->rstc);
+ }
+
+ timer_setup(&host->timer, dw_mci_cqe_cto_timer, 0);
+
+ spin_lock_init(&host->lock);
+ spin_lock_init(&host->irq_lock);
+ init_rwsem(&host->cr_rw_sem);
+ tasklet_init(&host->tasklet, dw_mci_cqe_tasklet_func, (unsigned long)host);
+
+ /*pio mode's parameters should be initialized here*/
+
+ /*Initialize the eMMC IP related attribute*/
+ dw_mci_cqe_setup(host);
+
+ dw_mci_cqe_init_dma(host);
+
+ /* This flag will be set 1 when doing tuning,
+ * we add this flag because
+ * some vendors might use other cmd instead of 21
+ * to tune phase under high speed interface.
+ * we use this flag to recognize if the system is under tuning stage.
+ */
+ host->tuning = 0;
+
+ /*Timing_setting is to avoid sending command
+ *before setting phase in hs200, hs400
+ */
+ host->current_speed = 0;
+
+ /*Do the rest of init for specific*/
+ if (drv_data && drv_data->init) {
+ ret = drv_data->init(host);
+ if (ret) {
+ dev_err(host->dev,
+ "implementation specific init failed\n");
+ goto err_dmaunmap;
+ }
+ }
+
+ ret = dw_mci_cqe_init_slot(host);
+ if (ret) {
+ dev_err(host->dev, "slot 0 init failed\n");
+ goto err_dmaunmap;
+ }
+
+ ret = devm_request_irq(host->dev, host->irq, dw_mci_cqe_interrupt,
+ host->irq_flags, "dw-mci-cqe", host);
+ if (ret)
+ goto err_dmaunmap;
+
+ /*After the slot initialization,
+ *now we have mmc data and can initialize cmdq if user enabled
+ */
+ dw_mci_cqhci_init(host);
+
+ return 0;
+
+err_dmaunmap:
+ if (!IS_ERR(host->pdata->rstc))
+ reset_control_assert(host->pdata->rstc);
+err_clk_ciu:
+ clk_disable_unprepare(host->ciu_clk);
+
+err_clk_biu:
+ clk_disable_unprepare(host->biu_clk);
+
+ return ret;
+}
+EXPORT_SYMBOL(dw_mci_cqe_probe);
+
+void dw_mci_cqe_remove(struct dw_mci *host)
+{
+ dev_dbg(host->dev, "remove slot\n");
+ if (host->slot)
+ dw_mci_cqe_cleanup_slot(host->slot);
+
+ if (!IS_ERR(host->pdata->rstc))
+ reset_control_assert(host->pdata->rstc);
+
+ clk_disable_unprepare(host->ciu_clk);
+ clk_disable_unprepare(host->biu_clk);
+
+}
+EXPORT_SYMBOL(dw_mci_cqe_remove);
+
+#ifdef CONFIG_PM
+int dw_mci_cqe_runtime_suspend(struct device *dev)
+{
+ struct dw_mci *host = dev_get_drvdata(dev);
+ int ret = 0;
+
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE)) {
+ if (host->slot) {
+ dev_info(host->dev, "cqe suspend\n");
+ ret = cqhci_suspend(host->slot->mmc);
+ if (ret) {
+ dev_err(host->dev, "cqe suspend failed\n");
+ return ret;
+ }
+ }
+ }
+
+ clk_disable_unprepare(host->ciu_clk);
+
+ return ret;
+}
+EXPORT_SYMBOL(dw_mci_cqe_runtime_suspend);
+
+int dw_mci_cqe_runtime_resume(struct device *dev)
+{
+ struct dw_mci *host = dev_get_drvdata(dev);
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int ret = 0;
+
+ clk_prepare_enable(host->ciu_clk);
+
+ dw_mci_cqe_setup(host);
+ if (drv_data && drv_data->init) {
+ ret = drv_data->init(host);
+ if (ret)
+ dev_err(host->dev, "implementation specific init failed\n");
+ }
+
+ init_completion(host->int_waiting);
+
+ if (host->pdata && (host->pdata->caps2 & MMC_CAP2_CQE)) {
+ if (host->slot) {
+ dev_info(host->dev, "cqe resume\n");
+ ret = cqhci_resume(host->slot->mmc);
+ if (ret)
+ dev_err(host->dev, "cqe resume failed\n");
+ }
+ }
+
+ dw_mci_cqe_setup_bus(host->slot, true);
+
+ return ret;
+}
+EXPORT_SYMBOL(dw_mci_cqe_runtime_resume);
+#endif /* CONFIG_PM */
+
+static int __init dw_mci_cqe_init(void)
+{
+ pr_info("Synopsys Designware Multimedia Card Interface Driver\n");
+ return 0;
+}
+
+static void __exit dw_mci_cqe_exit(void)
+{
+}
+
+module_init(dw_mci_cqe_init);
+module_exit(dw_mci_cqe_exit);
+
+MODULE_DESCRIPTION("DW Multimedia Card CMDQ Interface driver");
+MODULE_AUTHOR("<jyanchou@realtek.com>");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,444 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2023 Realtek Semiconductors, All Rights Reserved.
+ *
+ */
+
+#ifndef __DW_MMC_CQE_H
+#define __DW_MMC_CQE_H
+
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/mmc/core.h>
+#include <linux/reset.h>
+#include <linux/scatterlist.h>
+
+struct dw_mci {
+ spinlock_t lock;
+ spinlock_t irq_lock;
+ struct tasklet_struct tasklet;
+ struct rw_semaphore cr_rw_sem;
+
+ void __iomem *regs;
+ resource_size_t phy_regs;
+
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_command stop_abort;
+ struct mmc_command stat_ready;
+ struct mmc_data *data;
+
+ struct clk *biu_clk;
+ struct clk *ciu_clk;
+ struct dw_mci_slot *slot;
+ struct timer_list timer;
+ struct completion *int_waiting;
+
+ unsigned int *desc_vaddr;
+ unsigned int *sg_cpu;
+ dma_addr_t sg_dma;
+ int use_dma;
+
+ struct platform_device *pdev;
+ struct device *dev;
+ struct dw_mci_board *pdata;
+ const struct dw_mci_drv_data *drv_data;
+ void *priv;
+
+ u32 opcode;
+ u32 arg;
+ u16 normal_interrupt;
+ u16 error_interrupt;
+ u16 auto_error_interrupt;
+
+ u32 bus_hz;
+ u32 current_speed;
+ u32 stop_cmdr;
+ bool is_sbc;
+ int dma_64bit_address;
+ int using_dma;
+
+ unsigned long irq_flags; /* IRQ flags */
+ int irq;
+ int sdio_id0;
+
+ struct scatterlist *sg;
+ u32 dma_nents;
+
+ u8 tuning;
+ struct cqhci_host *cqe;
+};
+
+enum {
+ TRANS_MODE_PIO = 0,
+ TRANS_MODE_DMA,
+};
+
+enum dw_mci_cookie {
+ COOKIE_UNMAPPED,
+ COOKIE_PRE_MAPPED, /* mapped by pre_req() of dwmmc */
+ COOKIE_MAPPED, /* mapped by prepare_data() of dwmmc */
+};
+/* eMMC control register definition */
+#define SDMMC_SDMASA_R 0x000
+#define SDMMC_BLOCKSIZE_R 0x004
+#define SDMMC_BLOCKCOUNT_R 0x006
+#define SDMMC_ARGUMENT_R 0x008
+#define SDMMC_XFER_MODE_R 0x00c
+#define SDMMC_CMD_R 0x00e
+#define SDMMC_RESP01_R 0x010
+#define SDMMC_RESP23_R 0x014
+#define SDMMC_RESP45_R 0x018
+#define SDMMC_RESP67_R 0x01c
+#define SDMMC_BUF_DATA_R 0x020
+#define SDMMC_PSTATE_REG 0x024
+#define SDMMC_HOST_CTRL1_R 0x028
+#define SDMMC_PWR_CTRL_R 0x029
+#define SDMMC_BGAP_CTRL_R 0x02a
+#define SDMMC_CLK_CTRL_R 0x02c
+#define SDMMC_TOUT_CTRL_R 0x02e
+#define SDMMC_SW_RST_R 0x02f
+#define SDMMC_NORMAL_INT_STAT_R 0x030
+#define SDMMC_ERROR_INT_STAT_R 0x032
+#define SDMMC_NORMAL_INT_STAT_EN_R 0x034
+#define SDMMC_ERROR_INT_STAT_EN_R 0x036
+#define SDMMC_NORMAL_INT_SIGNAL_EN_R 0x038
+#define SDMMC_ERROR_INT_SIGNAL_EN_R 0x03a
+#define SDMMC_AUTO_CMD_STAT_R 0x03c
+#define SDMMC_HOST_CTRL2_R 0x03e
+#define SDMMC_ADMA_ERR_STAT_R 0x054
+#define SDMMC_ADMA_SA_LOW_R 0x058
+
+#define SDMMC_MSHC_CTRL_R 0x208
+#define SDMMC_CTRL_R 0x22c
+
+#define SDMMC_CMD_CONFLICT_CHECK BIT(0)
+#define CMD_IDX_MASK(x) ((x >> 8)&0x3f)
+
+/*0xc*/
+#define SDMMC_MULTI_BLK_SEL 5
+#define SDMMC_DATA_XFER_DIR 4
+#define SDMMC_BLOCK_COUNT_ENABLE BIT(1)
+#define SDMMC_DMA_ENABLE BIT(0)
+#define SDMMC_AUTO_CMD_ENABLE 2
+#define SDMMC_AUTO_CMD_DISABLED 0x0
+#define SDMMC_AUTO_CMD12_ENABLED 0x1
+#define SDMMC_AUTO_CMD23_ENABLED 0x2
+#define SDMMC_AUTO_CMD_SEL 0x3
+
+/*0xe*/
+#define SDMMC_RESP_TYPE_SELECT 0
+#define SDMMC_CMD_TYPE 6
+#define SDMMC_NO_RESP 0x0
+#define SDMMC_RESP_LEN_136 0x1
+#define SDMMC_RESP_LEN_48 0x2
+#define SDMMC_RESP_LEN_48B 0x3
+#define SDMMC_CMD_CHK_RESP_CRC BIT(3)
+#define SDMMC_CMD_IDX_CHK_ENABLE BIT(4)
+#define SDMMC_DATA BIT(5)
+#define SDMMC_ABORT_CMD 0x3
+#define SDMMC_RESUME_CMD 0x2
+#define SDMMC_SUSPEND_CMD 0x1
+#define SDMMC_NORMAL_CMD 0x0
+
+/*0x24 PSTATE*/
+#define SDMMC_CMD_INHIBIT BIT(0)
+#define SDMMC_CMD_INHIBIT_DAT BIT(1)
+#define SDMMC_DAT_3_0 (0xf << 20)
+#define SDMMC_DAT_7_4 (0xf << 4)
+
+/*0x28*/
+#define SDMMC_DMA_SEL 3
+#define SDMMC_SDMA (0x0)
+#define SDMMC_ADMA2_32 (0x2)
+#define SDMMC_ADMA2_64 (0x3)
+#define SDMMC_EXT_DAT_XFER BIT(5)
+#define SDMMC_EXT_DAT_XFER_MASK (~SDMMC_EXT_DAT_XFER & 0xff)
+#define SDMMC_HIGH_SPEED_EN BIT(2)
+#define SDMMC_HIGH_SPEED_MASK ((~BIT(2)) & 0xff)
+#define SDMMC_UHS_MODE_SEL_MASK ((~(BIT(0)|BIT(1)|BIT(2))) & 0xffff)
+#define SDMMC_DAT_XFER_WIDTH BIT(1)
+#define SDMMC_DAT_XFER_WIDTH_MASK (~SDMMC_DAT_XFER_WIDTH & 0xff)
+#define SDMMC_BUS_WIDTH_8 SDMMC_EXT_DAT_XFER
+#define SDMMC_BUS_WIDTH_4 SDMMC_DAT_XFER_WIDTH
+#define SDMMC_BUS_WIDTH_1 0
+#define SDMMC_DMA_SEL_CLR (0xff & (~(0x3<<SDMMC_DMA_SEL)))
+#define SDMMC_DATA_XFER_CLR ((0xff & (~SDMMC_EXT_DAT_XFER)) \
+ & (~SDMMC_DAT_XFER_WIDTH))
+
+/*0x2a*/
+#define SDMMC_STOP_BG_REQ BIT(0)
+
+/*0x2f SW_RST_R*/
+#define SDMMC_RST_DAT BIT(2)
+#define SDMMC_RST_CMD BIT(1)
+#define SDMMC_RST_ALL BIT(0)
+
+/*0x30 status bitmap*/
+#define SDMMC_STATUS_ALL 0xffff
+#define SDMMC_ERR_INTERRUPT BIT(15)
+#define SDMMC_CQE_EVENT BIT(14)
+#define SDMMC_FX_EVENT BIT(13)
+#define SDMMC_RE_TUNE_EVENT BIT(12)
+#define SDMMC_INT_C BIT(11)
+#define SDMMC_INT_B BIT(10)
+#define SDMMC_INT_A BIT(9)
+#define SDMMC_CARD_INTERRUPT BIT(8)
+#define SDMMC_CARD_REMOVAL BIT(7)
+#define SDMMC_CARD_INSERTION BIT(6)
+#define SDMMC_BUF_RD_READY BIT(5)
+#define SDMMC_BUF_WR_READY BIT(4)
+#define SDMMC_DMA_INTERRPT BIT(3)
+#define SDMMC_BGAP_EVENT BIT(2)
+#define SDMMC_XFER_COMPLETE BIT(1)
+#define SDMMC_CMD_COMPLETE BIT(0)
+
+/*0x32 error bitmap*/
+#define SDMMC_VENDOR_ERR3 BIT(15)
+#define SDMMC_VENDOR_ERR2 BIT(14)
+#define SDMMC_VENDOR_ERR1 BIT(13)
+#define SDMMC_BOOT_ACK_ERR BIT(12)
+#define SDMMC_RESP_ERR BIT(11)
+#define SDMMC_TUNING_ERR BIT(10)
+#define SDMMC_ADMA_ERR BIT(9)
+#define SDMMC_AUTO_CMD_ERR BIT(8)
+#define SDMMC_CUR_LMT_ERR BIT(7)
+#define SDMMC_DATA_END_BIT_ERR BIT(6)
+#define SDMMC_DATA_CRC_ERR BIT(5)
+#define SDMMC_DATA_TOUT_ERR BIT(4)
+#define SDMMC_CMD_IDX_ERR BIT(3)
+#define SDMMC_CMD_END_BIT_ERR BIT(2)
+#define SDMMC_CMD_CRC_ERR BIT(1)
+#define SDMMC_CMD_TOUT_ERR BIT(0)
+#define SDMMC_CMD_ERR (SDMMC_AUTO_CMD_ERR|SDMMC_CMD_IDX_ERR| \
+ SDMMC_CMD_END_BIT_ERR|SDMMC_CMD_CRC_ERR| \
+ SDMMC_CMD_TOUT_ERR)
+#define SDMMC_DATA_ERR (SDMMC_ADMA_ERR|SDMMC_DATA_END_BIT_ERR| \
+ SDMMC_DATA_CRC_ERR|SDMMC_DATA_TOUT_ERR)
+
+/*0x34 status enable bitmap*/
+#define SDMMC_CQE_EVENT_STAT_EN BIT(14)
+#define SDMMC_FX_EVENT_STAT_EN BIT(13)
+#define SDMMC_RE_TUNE_EVENT_STAT_EN BIT(12)
+#define SDMMC_INT_C_STAT_EN BIT(11)
+#define SDMMC_INT_B_STAT_EN BIT(10)
+#define SDMMC_INT_A_STAT_EN BIT(9)
+#define SDMMC_CARD_INTERRUPT_STAT_EN BIT(8)
+#define SDMMC_CARD_REMOVAL_STAT_EN BIT(7)
+#define SDMMC_CARD_INSERTION_STAT_EN BIT(6)
+#define SDMMC_BUF_RD_READY_STAT_EN BIT(5)
+#define SDMMC_BUF_WR_READY_STAT_EN BIT(4)
+#define SDMMC_DMA_INTERRPT_STAT_EN BIT(3)
+#define SDMMC_BGAP_EVENT_STAT_EN BIT(2)
+#define SDMMC_XFER_COMPLETE_STAT_EN BIT(1)
+#define SDMMC_CMD_COMPLETE_STAT_EN BIT(0)
+
+/*0x36 error status enable bitmap*/
+#define SDMMC_VENDOR_ERR_STAT_EN3 BIT(15)
+#define SDMMC_VENDOR_ERR_STAT_EN2 BIT(14)
+#define SDMMC_VENDOR_ERR_STAT_EN1 BIT(13)
+#define SDMMC_BOOT_ACK_ERR_STAT_EN BIT(12)
+#define SDMMC_RESP_ERR_STAT_EN BIT(11)
+#define SDMMC_TUNING_ERR_STAT_EN BIT(10)
+#define SDMMC_ADMA_ERR_STAT_EN BIT(9)
+#define SDMMC_AUTO_CMD_ERR_STAT_EN BIT(8)
+#define SDMMC_CUR_LMT_ERR_STAT_EN BIT(7)
+#define SDMMC_DATA_END_BIT_ERR_STAT_EN BIT(6)
+#define SDMMC_DATA_CRC_ERR_STAT_EN BIT(5)
+#define SDMMC_DATA_TOUT_ERR_STAT_EN BIT(4)
+#define SDMMC_CMD_IDX_ERR_STAT_EN BIT(3)
+#define SDMMC_CMD_END_BIT_ERR_STAT_EN BIT(2)
+#define SDMMC_CMD_CRC_ERR_STAT_EN BIT(1)
+#define SDMMC_CMD_TOUT_ERR_STAT_EN BIT(0)
+
+/*0x38 signal interrupt enable*/
+#define SDMMC_CQE_EVENT_SIGNAL_EN BIT(14)
+#define SDMMC_FX_EVENT_SIGNAL_EN BIT(13)
+#define SDMMC_RE_TUNE_EVENT_SIGNAL_EN BIT(12)
+#define SDMMC_INT_C_SIGNAL_EN BIT(11)
+#define SDMMC_INT_B_SIGNAL_EN BIT(10)
+#define SDMMC_INT_A_SIGNAL_EN BIT(9)
+#define SDMMC_CARD_INTERRUPT_SIGNAL_EN BIT(8)
+#define SDMMC_CARD_REMOVAL_SIGNAL_EN BIT(7)
+#define SDMMC_CARD_INSERTION_SIGNAL_EN BIT(6)
+#define SDMMC_BUF_RD_READY_SIGNAL_EN BIT(5)
+#define SDMMC_BUF_WR_READY_SIGNAL_EN BIT(4)
+#define SDMMC_DMA_INTERRPT_SIGNAL_EN BIT(3)
+#define SDMMC_BGAP_EVENT_SIGNAL_EN BIT(2)
+#define SDMMC_XFER_COMPLETE_SIGNAL_EN BIT(1)
+#define SDMMC_CMD_COMPLETE_SIGNAL_EN BIT(0)
+#define SDMMC_NORMAL_INT_SIGNAL_CMD_EN_R (~(BIT(6) | BIT(7) | BIT(8) | BIT(1)) & 0xffff)
+#define SDMMC_NORMAL_INT_SIGNAL_DAT_EN_R (~(BIT(6) | BIT(7) | BIT(8) | BIT(0)) & 0xffff)
+#define SDMMC_NORMAL_INT_SIGNAL_CQE_EN_R (~(BIT(6) | BIT(7) | BIT(8) | BIT(1) \
+ | BIT(0)) & 0xffff)
+
+/*0x3a error ssignal enable bitmap*/
+#define SDMMC_VENDOR_ERR_SIGNAL_EN3 BIT(15)
+#define SDMMC_VENDOR_ERR_SIGNAL_EN2 BIT(14)
+#define SDMMC_VENDOR_ERR_SIGNAL_EN1 BIT(13)
+#define SDMMC_BOOT_ACK_ERR_SIGNAL_EN BIT(12)
+#define SDMMC_RESP_ERR_SIGNAL_EN BIT(11)
+#define SDMMC_TUNING_ERR_SIGNAL_EN BIT(10)
+#define SDMMC_ADMA_ERR_SIGNAL_EN BIT(9)
+#define SDMMC_AUTO_CMD_ERR_SIGNAL_EN BIT(8)
+#define SDMMC_CUR_LMT_ERR_SIGNAL_EN BIT(7)
+#define SDMMC_DATA_END_BIT_ERR_SIGNAL_EN BIT(6)
+#define SDMMC_DATA_CRC_ERR_SIGNAL_EN BIT(5)
+#define SDMMC_DATA_TOUT_ERR_SIGNAL_EN BIT(4)
+#define SDMMC_CMD_IDX_ERR_SIGNAL_EN BIT(3)
+#define SDMMC_CMD_END_BIT_ERR_SIGNAL_EN BIT(2)
+#define SDMMC_CMD_CRC_ERR_SIGNAL_EN BIT(1)
+#define SDMMC_CMD_TOUT_ERR_STAT_EN BIT(0)
+
+#define SDMMC_ALL_NORMAL_STAT_EN (0xfeff)
+#define SDMMC_ALL_ERR_STAT_EN (0xffff)
+#define SDMMC_ALL_SIGNAL_STAT_EN (0xfeff)
+#define SDMMC_ALL_ERR_SIGNAL_EN (0xffff)
+
+/*0x3e*/
+#define SDMMC_LEGACY 0x0
+#define SDMMC_SDR 0x1
+#define SDMMC_HS200 0x3
+#define SDMMC_DDR 0x4
+#define SDMMC_HS400 0x7
+#define SDMMC_HOST_VER4_ENABLE BIT(12)
+#define SDMMC_SIGNALING_EN BIT(3)
+
+/*0x22c*/
+#define SDMMC_RST_N_OE BIT(3)
+#define SDMMC_RST_N BIT(2)
+#define SDMMC_CARD_IS_EMMC BIT(0)
+
+#define SDMMC_INTERNAL_CLK_EN BIT(0)
+#define SDMMC_PLL_USABLE BIT(0)
+
+#define VALID(x) ((x & 1) << 0)
+#define END(x) ((x & 1) << 1)
+#define INT(x) ((x & 1) << 2)
+#define ACT(x) ((x & 0x7) << 3)
+#define DAT_LENGTH(x) ((x & 0xFFFF) << 16)
+
+#define SW_RST_CMD_DONE 0x2000000
+#define SW_RST_DATA_DONE 0x4000000
+#define SW_RST_BOTH_DONE 0x6000000
+
+/* Register access macros */
+#define mcq_readl(dev, reg) \
+ readl_relaxed((dev)->regs + SDMMC_##reg)
+#define mcq_writel(dev, reg, value) \
+ writel_relaxed((value), (dev)->regs + SDMMC_##reg)
+
+#define mcq_readw(dev, reg) \
+ readw_relaxed((dev)->regs + SDMMC_##reg)
+#define mcq_writew(dev, reg, value) \
+ writew_relaxed((value), (dev)->regs + SDMMC_##reg)
+
+#define mcq_readb(dev, reg) \
+ readb_relaxed((dev)->regs + SDMMC_##reg)
+#define mcq_writeb(dev, reg, value) \
+ writeb_relaxed((value), (dev)->regs + SDMMC_##reg)
+
+#define dw_mci_get_int(dev) \
+ do { \
+ dev->normal_interrupt = mcq_readw(dev, NORMAL_INT_STAT_R); \
+ dev->error_interrupt = mcq_readw(dev, ERROR_INT_STAT_R); \
+ dev->auto_error_interrupt = mcq_readw(dev, AUTO_CMD_STAT_R); \
+ } while (0)
+
+/*clear status register, we always keep the card interrupt*/
+#define dw_mci_clr_int(dev) \
+ do { \
+ mcq_writew(dev, ERROR_INT_STAT_R, mcq_readw(dev, ERROR_INT_STAT_R) & 0xffff); \
+ mcq_writew(dev, NORMAL_INT_STAT_R, mcq_readw(dev, NORMAL_INT_STAT_R) & 0xffff); \
+ } while (0)
+
+/*mask all emmc interrupts*/
+#define dw_mci_clr_signal_int(dev) \
+ do { \
+ mcq_writew(dev, NORMAL_INT_SIGNAL_EN_R, mcq_readw(dev, NORMAL_INT_SIGNAL_EN_R) \
+ & (BIT(6)|BIT(7))); \
+ mcq_writew(dev, ERROR_INT_SIGNAL_EN_R, 0); \
+ } while (0)
+
+/*for cmdq, we do not need cmd and xfer done, only cqe event*/
+#define dw_mci_en_cqe_int(dev) \
+ do { \
+ mcq_writew(dev, NORMAL_INT_SIGNAL_EN_R, \
+ mcq_readw(dev, NORMAL_INT_SIGNAL_EN_R) | \
+ SDMMC_NORMAL_INT_SIGNAL_CQE_EN_R); \
+ mcq_writew(dev, ERROR_INT_SIGNAL_EN_R, SDMMC_ALL_ERR_SIGNAL_EN); \
+ } while (0)
+
+/*used for data, r1b case, we mask cmd done interrupt*/
+#define dw_mci_en_xfer_int(dev) \
+ do { \
+ mcq_writew(dev, NORMAL_INT_SIGNAL_EN_R, \
+ mcq_readw(dev, NORMAL_INT_SIGNAL_EN_R)|SDMMC_NORMAL_INT_SIGNAL_DAT_EN_R); \
+ mcq_writew(dev, ERROR_INT_SIGNAL_EN_R, SDMMC_ALL_ERR_SIGNAL_EN); \
+ } while (0)
+
+/*used for none-stream case (cmd w/wo/ resp)*/
+#define dw_mci_en_cd_int(dev) \
+ do { \
+ mcq_writew(dev, NORMAL_INT_SIGNAL_EN_R, \
+ mcq_readw(dev, NORMAL_INT_SIGNAL_EN_R)|SDMMC_NORMAL_INT_SIGNAL_CMD_EN_R); \
+ mcq_writew(dev, ERROR_INT_SIGNAL_EN_R, SDMMC_ALL_ERR_SIGNAL_EN); \
+ } while (0)
+
+extern int dw_mci_cqe_probe(struct dw_mci *host);
+extern void dw_mci_cqe_remove(struct dw_mci *host);
+#ifdef CONFIG_PM
+extern int dw_mci_cqe_runtime_suspend(struct device *device);
+extern int dw_mci_cqe_runtime_resume(struct device *device);
+#endif
+irqreturn_t cqhci_irq(struct mmc_host *mmc, u32 intmask, int cmd_error, int data_error);
+void cqhci_set_tran_desc(u8 *desc, dma_addr_t addr, int len, bool end, bool dma64);
+
+/* Board platform data */
+struct dw_mci_board {
+ unsigned int bus_hz; /* Clock speed at the cclk_in pad */
+ u32 caps; /* Capabilities */
+ u32 caps2; /* More capabilities */
+ u32 pm_caps; /* PM capabilities */
+
+ /* delay in mS before detecting cards after interrupt */
+ u32 detect_delay_ms;
+
+ struct reset_control *rstc;
+};
+
+struct dw_mci_slot {
+ struct mmc_host *mmc;
+ struct dw_mci *host;
+
+ struct mmc_request *mrq;
+
+ unsigned int clock;
+ unsigned int __clk_old;
+
+ unsigned long flags;
+#define DW_MMC_CARD_PRESENT 1
+ int id;
+ int sdio_id;
+ u8 switch_partition;
+};
+
+struct dw_mci_drv_data {
+ unsigned long *caps;
+ u32 num_caps;
+ int (*init)(struct dw_mci *host);
+ void (*set_ios)(struct dw_mci_slot *slot, struct mmc_ios *ios);
+ int (*parse_dt)(struct dw_mci *host);
+ int (*execute_tuning)(struct dw_mci_slot *slot, u32 opcode);
+ int (*prepare_hs400_tuning)(struct dw_mci *host,
+ struct mmc_ios *ios);
+ int (*switch_voltage)(struct mmc_host *mmc,
+ struct mmc_ios *ios);
+ void (*hs400_complete)(struct mmc_host *mmc);
+ void (*init_card)(struct mmc_host *host,
+ struct mmc_card *card);
+ void (*shift_rsp)(struct dw_mci *host, struct mmc_command *cmd, u32 *rsp);
+};
+
+void dw_mci_cqe_wait_done(struct dw_mci *host, u32 *addr, u32 mask, u32 value);
+#endif
We implemented cmdq feature on Synopsys DesignWare mmc driver. The difference between dw_mmc.c and dw_mmc_cqe.c were distinct register definitions, mmc user flow and the addition of cmdq. New version of User Guide had modify mmc driver's usage flow, we may need to renew code to precisely follow user guide. More over, We added a wait status function to satisfy synopsys user guide's description, since this flow might be specific in synopsys host driver only. Signed-off-by: Jyan Chou <jyanchou@realtek.com> —-- v0 -> v1: - Seperate different support into single patch. - Fix the compiler complains. v1 -> v2: - Remove dw_mci_cqe_set_tran_desc due to the duplicated function. - Add ->pre_enable() / ->post_disable() --- --- drivers/mmc/host/Kconfig | 13 + drivers/mmc/host/Makefile | 1 + drivers/mmc/host/dw_mmc_cqe.c | 1619 +++++++++++++++++++++++++++++++++ drivers/mmc/host/dw_mmc_cqe.h | 444 +++++++++ 4 files changed, 2077 insertions(+) create mode 100644 drivers/mmc/host/dw_mmc_cqe.c create mode 100644 drivers/mmc/host/dw_mmc_cqe.h