diff mbox series

[v2] mmc: mtk-sd: Implement Host Software Queue for eMMC and SD Card

Message ID 20240930090156.33537-1-angelogioacchino.delregno@collabora.com (mailing list archive)
State New
Headers show
Series [v2] mmc: mtk-sd: Implement Host Software Queue for eMMC and SD Card | expand

Commit Message

AngeloGioacchino Del Regno Sept. 30, 2024, 9:01 a.m. UTC
Add support for Host Software Queue (HSQ) and enable it when the
controller instance does not have Command Queue Engine HW support.

It was chosen to enable HSQ only for eMMC and SD/MicroSD cards
and not for SDIO as performance improvements are seen only for
the former.

Performance was measured with a SanDisk Extreme Ultra A2 MicroSD
card in a MediaTek MT8195T Acer Chromebook Spin 513 (CP513-2H),
by running FIO (bs=4k) on an ArchLinux userspace.

.... Summarizing ....
Random read:     +24.28% IOPS, +24.29% BW
Sequential read: +3.14%  IOPS, +3.49%  BW
Random RW (avg): +50.53% IOPS, +50.68% BW

Below, more data from the benchmarks.

Before:
 - Random read: IOPS=1643, BW=6574KiB/s
   bw (  KiB/s): min= 4578, max= 7440, per=99.95%, avg=6571.55, stdev=74.16, samples=953
   iops        : min= 1144, max= 1860, avg=1642.14, stdev=18.54, samples=953
   lat (msec)  : 100=0.01%, 250=0.12%, 500=0.38%, 750=97.89%, 1000=1.44%, 2000=0.16%
 - Sequential read: IOPS=19.1k, BW=74.4MiB/s
   bw (  KiB/s): min=12288, max=118483, per=100.00%, avg=76293.38, stdev=1971.42, samples=956
   iops        : min= 3072, max=29620, avg=19072.14, stdev=492.87, samples=956
   lat (msec)  : 4=0.01%, 10=0.01%, 20=0.21%, 50=23.95%, 100=75.67%, 250=0.05%, 500=0.03%, 750=0.08%
 - Random R/W: read: IOPS=282, BW=1129KiB/s (1156kB/s)  write: IOPS=284, BW=1136KiB/s
   read bw (  KiB/s): min=   31, max= 3496, per=100.00%, avg=1703.67, stdev=155.42, samples=630
   read iops        : min=    7, max=  873, avg=425.22, stdev=38.85, samples=630
   wri  bw (  KiB/s): min=   31, max= 3443, per=100.00%, avg=1674.27, stdev=164.23, samples=644
   wri  iops        : min=    7, max=  860, avg=417.87, stdev=41.03, samples=644
   lat (msec)   : 250=0.13%, 500=0.44%, 750=0.84%, 1000=22.29%, 2000=74.01%, >=2000=2.30%

After:
 - Random read: IOPS=2042, BW=8171KiB/s
   bw (  KiB/s): min= 4907, max= 9072, per=99.94%, avg=8166.80, stdev=93.77, samples=954
   iops        : min= 1226, max= 2268, avg=2040.78, stdev=23.41, samples=954
   lat (msec)   : 100=0.03%, 250=0.13%, 500=52.88%, 750=46.64%, 1000=0.32%
 - Sequential read: IOPS=19.7k, BW=77.0MiB/s
   bw (  KiB/s): min=67980, max=94248, per=100.00%, avg=78894.27, stdev=1475.07, samples=956
   iops        : min=16994, max=23562, avg=19722.45, stdev=368.76, samples=956
   lat (msec)   : 4=0.01%, 10=0.01%, 20=0.05%, 50=28.78%, 100=71.14%, 250=0.01%, 500=0.02%
 - Random R/W: read: IOPS=424, BW=1699KiB/s  write: IOPS=428, BW=1714KiB/s
   read bw (  KiB/s): min=  228, max= 2856, per=100.00%, avg=1796.60, stdev=112.59, samples=901
   read iops        : min=   54, max=  712, avg=447.81, stdev=28.21, samples=901
   wri  bw (  KiB/s): min=   28, max= 2904, per=100.00%, avg=1780.11, stdev=128.27, samples=916
   wri  iops        : min=    4, max=  724, avg=443.69, stdev=32.14, samples=916

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---

Changes in v2:
 - Added missing `select MMC_HSQ` for MMC_MTK Kconfig

 drivers/mmc/host/Kconfig  |  1 +
 drivers/mmc/host/mtk-sd.c | 49 +++++++++++++++++++++++++++++++++++++--
 2 files changed, 48 insertions(+), 2 deletions(-)

Comments

Ulf Hansson Oct. 8, 2024, 2:35 p.m. UTC | #1
On Mon, 30 Sept 2024 at 11:01, AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com> wrote:
>
> Add support for Host Software Queue (HSQ) and enable it when the
> controller instance does not have Command Queue Engine HW support.
>
> It was chosen to enable HSQ only for eMMC and SD/MicroSD cards
> and not for SDIO as performance improvements are seen only for
> the former.
>
> Performance was measured with a SanDisk Extreme Ultra A2 MicroSD
> card in a MediaTek MT8195T Acer Chromebook Spin 513 (CP513-2H),
> by running FIO (bs=4k) on an ArchLinux userspace.
>
> .... Summarizing ....
> Random read:     +24.28% IOPS, +24.29% BW
> Sequential read: +3.14%  IOPS, +3.49%  BW
> Random RW (avg): +50.53% IOPS, +50.68% BW
>
> Below, more data from the benchmarks.
>
> Before:
>  - Random read: IOPS=1643, BW=6574KiB/s
>    bw (  KiB/s): min= 4578, max= 7440, per=99.95%, avg=6571.55, stdev=74.16, samples=953
>    iops        : min= 1144, max= 1860, avg=1642.14, stdev=18.54, samples=953
>    lat (msec)  : 100=0.01%, 250=0.12%, 500=0.38%, 750=97.89%, 1000=1.44%, 2000=0.16%
>  - Sequential read: IOPS=19.1k, BW=74.4MiB/s
>    bw (  KiB/s): min=12288, max=118483, per=100.00%, avg=76293.38, stdev=1971.42, samples=956
>    iops        : min= 3072, max=29620, avg=19072.14, stdev=492.87, samples=956
>    lat (msec)  : 4=0.01%, 10=0.01%, 20=0.21%, 50=23.95%, 100=75.67%, 250=0.05%, 500=0.03%, 750=0.08%
>  - Random R/W: read: IOPS=282, BW=1129KiB/s (1156kB/s)  write: IOPS=284, BW=1136KiB/s
>    read bw (  KiB/s): min=   31, max= 3496, per=100.00%, avg=1703.67, stdev=155.42, samples=630
>    read iops        : min=    7, max=  873, avg=425.22, stdev=38.85, samples=630
>    wri  bw (  KiB/s): min=   31, max= 3443, per=100.00%, avg=1674.27, stdev=164.23, samples=644
>    wri  iops        : min=    7, max=  860, avg=417.87, stdev=41.03, samples=644
>    lat (msec)   : 250=0.13%, 500=0.44%, 750=0.84%, 1000=22.29%, 2000=74.01%, >=2000=2.30%
>
> After:
>  - Random read: IOPS=2042, BW=8171KiB/s
>    bw (  KiB/s): min= 4907, max= 9072, per=99.94%, avg=8166.80, stdev=93.77, samples=954
>    iops        : min= 1226, max= 2268, avg=2040.78, stdev=23.41, samples=954
>    lat (msec)   : 100=0.03%, 250=0.13%, 500=52.88%, 750=46.64%, 1000=0.32%
>  - Sequential read: IOPS=19.7k, BW=77.0MiB/s
>    bw (  KiB/s): min=67980, max=94248, per=100.00%, avg=78894.27, stdev=1475.07, samples=956
>    iops        : min=16994, max=23562, avg=19722.45, stdev=368.76, samples=956
>    lat (msec)   : 4=0.01%, 10=0.01%, 20=0.05%, 50=28.78%, 100=71.14%, 250=0.01%, 500=0.02%
>  - Random R/W: read: IOPS=424, BW=1699KiB/s  write: IOPS=428, BW=1714KiB/s
>    read bw (  KiB/s): min=  228, max= 2856, per=100.00%, avg=1796.60, stdev=112.59, samples=901
>    read iops        : min=   54, max=  712, avg=447.81, stdev=28.21, samples=901
>    wri  bw (  KiB/s): min=   28, max= 2904, per=100.00%, avg=1780.11, stdev=128.27, samples=916
>    wri  iops        : min=    4, max=  724, avg=443.69, stdev=32.14, samples=916
>
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Applied for next, thanks!

Kind regards
Uffe


> ---
>
> Changes in v2:
>  - Added missing `select MMC_HSQ` for MMC_MTK Kconfig
>
>  drivers/mmc/host/Kconfig  |  1 +
>  drivers/mmc/host/mtk-sd.c | 49 +++++++++++++++++++++++++++++++++++++--
>  2 files changed, 48 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 7199cb0bd0b9..0ba5a9f769fb 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -1009,6 +1009,7 @@ config MMC_MTK
>         depends on COMMON_CLK
>         select REGULATOR
>         select MMC_CQHCI
> +       select MMC_HSQ
>         help
>           This selects the MediaTek(R) Secure digital and Multimedia card Interface.
>           If you have a machine with a integrated SD/MMC card reader, say Y or M here.
> diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> index 5165a33bf74b..a9a554bd3f44 100644
> --- a/drivers/mmc/host/mtk-sd.c
> +++ b/drivers/mmc/host/mtk-sd.c
> @@ -33,6 +33,7 @@
>  #include <linux/mmc/slot-gpio.h>
>
>  #include "cqhci.h"
> +#include "mmc_hsq.h"
>
>  #define MAX_BD_NUM          1024
>  #define MSDC_NR_CLOCKS      3
> @@ -473,6 +474,7 @@ struct msdc_host {
>         bool hs400_tuning;      /* hs400 mode online tuning */
>         bool internal_cd;       /* Use internal card-detect logic */
>         bool cqhci;             /* support eMMC hw cmdq */
> +       bool hsq_en;            /* Host Software Queue is enabled */
>         struct msdc_save_para save_para; /* used when gate HCLK */
>         struct msdc_tune_para def_tune_para; /* default tune setting */
>         struct msdc_tune_para saved_tune_para; /* tune result of CMD21/CMD19 */
> @@ -1170,7 +1172,9 @@ static void msdc_track_cmd_data(struct msdc_host *host, struct mmc_command *cmd)
>
>  static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
>  {
> +       struct mmc_host *mmc = mmc_from_priv(host);
>         unsigned long flags;
> +       bool hsq_req_done;
>
>         /*
>          * No need check the return value of cancel_delayed_work, as only ONE
> @@ -1178,6 +1182,27 @@ static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
>          */
>         cancel_delayed_work(&host->req_timeout);
>
> +       /*
> +        * If the request was handled from Host Software Queue, there's almost
> +        * nothing to do here, and we also don't need to reset mrq as any race
> +        * condition would not have any room to happen, since HSQ stores the
> +        * "scheduled" mrqs in an internal array of mrq slots anyway.
> +        * However, if the controller experienced an error, we still want to
> +        * reset it as soon as possible.
> +        *
> +        * Note that non-HSQ requests will still be happening at times, even
> +        * though it is enabled, and that's what is going to reset host->mrq.
> +        * Also, msdc_unprepare_data() is going to be called by HSQ when needed
> +        * as HSQ request finalization will eventually call the .post_req()
> +        * callback of this driver which, in turn, unprepares the data.
> +        */
> +       hsq_req_done = host->hsq_en ? mmc_hsq_finalize_request(mmc, mrq) : false;
> +       if (hsq_req_done) {
> +               if (host->error)
> +                       msdc_reset_hw(host);
> +               return;
> +       }
> +
>         spin_lock_irqsave(&host->lock, flags);
>         host->mrq = NULL;
>         spin_unlock_irqrestore(&host->lock, flags);
> @@ -1187,7 +1212,7 @@ static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
>                 msdc_unprepare_data(host, mrq->data);
>         if (host->error)
>                 msdc_reset_hw(host);
> -       mmc_request_done(mmc_from_priv(host), mrq);
> +       mmc_request_done(mmc, mrq);
>         if (host->dev_comp->recheck_sdio_irq)
>                 msdc_recheck_sdio_irq(host);
>  }
> @@ -1347,7 +1372,7 @@ static void msdc_ops_request(struct mmc_host *mmc, struct mmc_request *mrq)
>         struct msdc_host *host = mmc_priv(mmc);
>
>         host->error = 0;
> -       WARN_ON(host->mrq);
> +       WARN_ON(!host->hsq_en && host->mrq);
>         host->mrq = mrq;
>
>         if (mrq->data)
> @@ -2916,6 +2941,19 @@ static int msdc_drv_probe(struct platform_device *pdev)
>                 mmc->max_seg_size = 64 * 1024;
>                 /* Reduce CIT to 0x40 that corresponds to 2.35us */
>                 msdc_cqe_cit_cal(host, 2350);
> +       } else if (mmc->caps2 & MMC_CAP2_NO_SDIO) {
> +               /* Use HSQ on eMMC/SD (but not on SDIO) if HW CQE not supported */
> +               struct mmc_hsq *hsq = devm_kzalloc(&pdev->dev, sizeof(*hsq), GFP_KERNEL);
> +               if (!hsq) {
> +                       ret = -ENOMEM;
> +                       goto release;
> +               }
> +
> +               ret = mmc_hsq_init(hsq, mmc);
> +               if (ret)
> +                       goto release;
> +
> +               host->hsq_en = true;
>         }
>
>         ret = devm_request_irq(&pdev->dev, host->irq, msdc_irq,
> @@ -3043,6 +3081,9 @@ static int __maybe_unused msdc_runtime_suspend(struct device *dev)
>         struct mmc_host *mmc = dev_get_drvdata(dev);
>         struct msdc_host *host = mmc_priv(mmc);
>
> +       if (host->hsq_en)
> +               mmc_hsq_suspend(mmc);
> +
>         msdc_save_reg(host);
>
>         if (sdio_irq_claimed(mmc)) {
> @@ -3073,6 +3114,10 @@ static int __maybe_unused msdc_runtime_resume(struct device *dev)
>                 pinctrl_select_state(host->pinctrl, host->pins_uhs);
>                 enable_irq(host->irq);
>         }
> +
> +       if (host->hsq_en)
> +               mmc_hsq_resume(mmc);
> +
>         return 0;
>  }
>
> --
> 2.46.1
>
diff mbox series

Patch

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 7199cb0bd0b9..0ba5a9f769fb 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -1009,6 +1009,7 @@  config MMC_MTK
 	depends on COMMON_CLK
 	select REGULATOR
 	select MMC_CQHCI
+	select MMC_HSQ
 	help
 	  This selects the MediaTek(R) Secure digital and Multimedia card Interface.
 	  If you have a machine with a integrated SD/MMC card reader, say Y or M here.
diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 5165a33bf74b..a9a554bd3f44 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -33,6 +33,7 @@ 
 #include <linux/mmc/slot-gpio.h>
 
 #include "cqhci.h"
+#include "mmc_hsq.h"
 
 #define MAX_BD_NUM          1024
 #define MSDC_NR_CLOCKS      3
@@ -473,6 +474,7 @@  struct msdc_host {
 	bool hs400_tuning;	/* hs400 mode online tuning */
 	bool internal_cd;	/* Use internal card-detect logic */
 	bool cqhci;		/* support eMMC hw cmdq */
+	bool hsq_en;		/* Host Software Queue is enabled */
 	struct msdc_save_para save_para; /* used when gate HCLK */
 	struct msdc_tune_para def_tune_para; /* default tune setting */
 	struct msdc_tune_para saved_tune_para; /* tune result of CMD21/CMD19 */
@@ -1170,7 +1172,9 @@  static void msdc_track_cmd_data(struct msdc_host *host, struct mmc_command *cmd)
 
 static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
 {
+	struct mmc_host *mmc = mmc_from_priv(host);
 	unsigned long flags;
+	bool hsq_req_done;
 
 	/*
 	 * No need check the return value of cancel_delayed_work, as only ONE
@@ -1178,6 +1182,27 @@  static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
 	 */
 	cancel_delayed_work(&host->req_timeout);
 
+	/*
+	 * If the request was handled from Host Software Queue, there's almost
+	 * nothing to do here, and we also don't need to reset mrq as any race
+	 * condition would not have any room to happen, since HSQ stores the
+	 * "scheduled" mrqs in an internal array of mrq slots anyway.
+	 * However, if the controller experienced an error, we still want to
+	 * reset it as soon as possible.
+	 *
+	 * Note that non-HSQ requests will still be happening at times, even
+	 * though it is enabled, and that's what is going to reset host->mrq.
+	 * Also, msdc_unprepare_data() is going to be called by HSQ when needed
+	 * as HSQ request finalization will eventually call the .post_req()
+	 * callback of this driver which, in turn, unprepares the data.
+	 */
+	hsq_req_done = host->hsq_en ? mmc_hsq_finalize_request(mmc, mrq) : false;
+	if (hsq_req_done) {
+		if (host->error)
+			msdc_reset_hw(host);
+		return;
+	}
+
 	spin_lock_irqsave(&host->lock, flags);
 	host->mrq = NULL;
 	spin_unlock_irqrestore(&host->lock, flags);
@@ -1187,7 +1212,7 @@  static void msdc_request_done(struct msdc_host *host, struct mmc_request *mrq)
 		msdc_unprepare_data(host, mrq->data);
 	if (host->error)
 		msdc_reset_hw(host);
-	mmc_request_done(mmc_from_priv(host), mrq);
+	mmc_request_done(mmc, mrq);
 	if (host->dev_comp->recheck_sdio_irq)
 		msdc_recheck_sdio_irq(host);
 }
@@ -1347,7 +1372,7 @@  static void msdc_ops_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	struct msdc_host *host = mmc_priv(mmc);
 
 	host->error = 0;
-	WARN_ON(host->mrq);
+	WARN_ON(!host->hsq_en && host->mrq);
 	host->mrq = mrq;
 
 	if (mrq->data)
@@ -2916,6 +2941,19 @@  static int msdc_drv_probe(struct platform_device *pdev)
 		mmc->max_seg_size = 64 * 1024;
 		/* Reduce CIT to 0x40 that corresponds to 2.35us */
 		msdc_cqe_cit_cal(host, 2350);
+	} else if (mmc->caps2 & MMC_CAP2_NO_SDIO) {
+		/* Use HSQ on eMMC/SD (but not on SDIO) if HW CQE not supported */
+		struct mmc_hsq *hsq = devm_kzalloc(&pdev->dev, sizeof(*hsq), GFP_KERNEL);
+		if (!hsq) {
+			ret = -ENOMEM;
+			goto release;
+		}
+
+		ret = mmc_hsq_init(hsq, mmc);
+		if (ret)
+			goto release;
+
+		host->hsq_en = true;
 	}
 
 	ret = devm_request_irq(&pdev->dev, host->irq, msdc_irq,
@@ -3043,6 +3081,9 @@  static int __maybe_unused msdc_runtime_suspend(struct device *dev)
 	struct mmc_host *mmc = dev_get_drvdata(dev);
 	struct msdc_host *host = mmc_priv(mmc);
 
+	if (host->hsq_en)
+		mmc_hsq_suspend(mmc);
+
 	msdc_save_reg(host);
 
 	if (sdio_irq_claimed(mmc)) {
@@ -3073,6 +3114,10 @@  static int __maybe_unused msdc_runtime_resume(struct device *dev)
 		pinctrl_select_state(host->pinctrl, host->pins_uhs);
 		enable_irq(host->irq);
 	}
+
+	if (host->hsq_en)
+		mmc_hsq_resume(mmc);
+
 	return 0;
 }