| Message ID | 20241003161007.3485810-1-m.wilczynski@samsung.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | [v1] mmc: sdhci: Prevent stale command and data interrupt handling | expand |
On 3/10/24 19:10, Michal Wilczynski wrote: > While working with the T-Head 1520 LicheePi4A SoC, certain conditions > arose that allowed me to reproduce a race issue in the sdhci code. > > To reproduce the bug, you need to enable the sdio1 controller in the > device tree file > `arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi` as follows: > > &sdio1 { > bus-width = <4>; > max-frequency = <100000000>; > no-sd; > no-mmc; > broken-cd; > cap-sd-highspeed; > post-power-on-delay-ms = <50>; > status = "okay"; > wakeup-source; > keep-power-in-suspend; > }; > > When resetting the SoC using the reset button, the following messages > appear in the dmesg log: > > [ 8.164898] mmc2: Got command interrupt 0x00000001 even though no > command operation was in progress. > [ 8.174054] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== > [ 8.180503] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000005 > [ 8.186950] mmc2: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 > [ 8.193395] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 > [ 8.199841] mmc2: sdhci: Present: 0x03da0000 | Host ctl: 0x00000000 > [ 8.206287] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 > [ 8.212733] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000decf > [ 8.219178] mmc2: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 > [ 8.225622] mmc2: sdhci: Int enab: 0x00ff1003 | Sig enab: 0x00ff1003 > [ 8.232068] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 > [ 8.238513] mmc2: sdhci: Caps: 0x3f69c881 | Caps_1: 0x08008177 > [ 8.244959] mmc2: sdhci: Cmd: 0x00000502 | Max curr: 0x00191919 > [ 8.254115] mmc2: sdhci: Resp[0]: 0x00001009 | Resp[1]: 0x00000000 > [ 8.260561] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 > [ 8.267005] mmc2: sdhci: Host ctl2: 0x00001000 > [ 8.271453] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: > 0x0000000000000000 > [ 8.278594] mmc2: sdhci: ============================================ > > I also enabled some traces to better understand the problem: > > kworker/3:1-62 [003] ..... 8.163538: mmc_request_start: > mmc2: start struct mmc_request[000000000d30cc0c]: cmd_opcode=5 > cmd_arg=0x0 cmd_flags=0x2e1 cmd_retries=0 stop_opcode=0 stop_arg=0x0 > stop_flags=0x0 stop_retries=0 sbc_opcode=0 sbc_arg=0x0 sbc_flags=0x0 > sbc_retires=0 blocks=0 block_size=0 blk_addr=0 data_flags=0x0 tag=0 > can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1 > retune_period=0 > <idle>-0 [000] d.h2. 8.164816: sdhci_cmd_irq: > hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x10000 > intmask_p=0x18000 > irq/24-mmc2-96 [000] ..... 8.164840: sdhci_thread_irq: > msg= > irq/24-mmc2-96 [000] d.h2. 8.164896: sdhci_cmd_irq: > hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x1 > intmask_p=0x1 > irq/24-mmc2-96 [000] ..... 8.285142: mmc_request_done: > mmc2: end struct mmc_request[000000000d30cc0c]: cmd_opcode=5 > cmd_err=-110 cmd_resp=0x0 0x0 0x0 0x0 cmd_retries=0 stop_opcode=0 > stop_err=0 stop_resp=0x0 0x0 0x0 0x0 stop_retries=0 sbc_opcode=0 > sbc_err=0 sbc_resp=0x0 0x0 0x0 0x0 sbc_retries=0 bytes_xfered=0 > data_err=0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0 > hold_retune=1 retune_period=0 > > Here's what happens: the __mmc_start_request function is called with > opcode 5. Since the power to the Wi-Fi card, which resides on this SDIO > bus, is initially off after the reset, an interrupt SDHCI_INT_TIMEOUT is > triggered. Immediately after that, a second interrupt SDHCI_INT_RESPONSE > is triggered. Depending on the exact timing, these conditions can > trigger the following race problem: > > 1) The sdhci_cmd_irq top half handles the command as an error. It sets > host->cmd to NULL and host->pending_reset to true. > 2) The sdhci_thread_irq bottom half is scheduled next and executes faster > than the second interrupt handler for SDHCI_INT_RESPONSE. It clears > host->pending_reset before the SDHCI_INT_RESPONSE handler runs. > 3) The pending interrupt SDHCI_INT_RESPONSE handler gets called, triggering > a code path that prints: "mmc2: Got command interrupt 0x00000001 even > though no command operation was in progress." > > To solve this issue, we need to clear pending interrupts when resetting > host->pending_reset. This ensures that after sdhci_threaded_irq restores > interrupts, there are no pending stale interrupts. > > Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com> > --- > drivers/mmc/host/sdhci.c | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c > index 4b91c9e96635..b91a6076c332 100644 > --- a/drivers/mmc/host/sdhci.c > +++ b/drivers/mmc/host/sdhci.c > @@ -3098,6 +3098,10 @@ static bool sdhci_request_done(struct sdhci_host *host) > sdhci_reset_for(host, REQUEST_ERROR); > > host->pending_reset = false; > + > + /* Clear any pending interrupts after reset */ > + sdhci_writel(host, SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK, > + SDHCI_INT_STATUS); According to SDHCI spec, "Software Reset For CMD Line" clears "Command Complete" in "Normal Interrupt Status register", so the interrupt status should not need to be cleared again. Which SDHCI driver is it? > } > > /*
On 10/7/24 18:09, Adrian Hunter wrote: > On 3/10/24 19:10, Michal Wilczynski wrote: >> While working with the T-Head 1520 LicheePi4A SoC, certain conditions >> arose that allowed me to reproduce a race issue in the sdhci code. >> >> To reproduce the bug, you need to enable the sdio1 controller in the >> device tree file >> `arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi` as follows: >> >> &sdio1 { >> bus-width = <4>; >> max-frequency = <100000000>; >> no-sd; >> no-mmc; >> broken-cd; >> cap-sd-highspeed; >> post-power-on-delay-ms = <50>; >> status = "okay"; >> wakeup-source; >> keep-power-in-suspend; >> }; >> >> When resetting the SoC using the reset button, the following messages >> appear in the dmesg log: >> >> [ 8.164898] mmc2: Got command interrupt 0x00000001 even though no >> command operation was in progress. >> [ 8.174054] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== >> [ 8.180503] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000005 >> [ 8.186950] mmc2: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 >> [ 8.193395] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 >> [ 8.199841] mmc2: sdhci: Present: 0x03da0000 | Host ctl: 0x00000000 >> [ 8.206287] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 >> [ 8.212733] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000decf >> [ 8.219178] mmc2: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 >> [ 8.225622] mmc2: sdhci: Int enab: 0x00ff1003 | Sig enab: 0x00ff1003 >> [ 8.232068] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 >> [ 8.238513] mmc2: sdhci: Caps: 0x3f69c881 | Caps_1: 0x08008177 >> [ 8.244959] mmc2: sdhci: Cmd: 0x00000502 | Max curr: 0x00191919 >> [ 8.254115] mmc2: sdhci: Resp[0]: 0x00001009 | Resp[1]: 0x00000000 >> [ 8.260561] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 >> [ 8.267005] mmc2: sdhci: Host ctl2: 0x00001000 >> [ 8.271453] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: >> 0x0000000000000000 >> [ 8.278594] mmc2: sdhci: ============================================ >> >> I also enabled some traces to better understand the problem: >> >> kworker/3:1-62 [003] ..... 8.163538: mmc_request_start: >> mmc2: start struct mmc_request[000000000d30cc0c]: cmd_opcode=5 >> cmd_arg=0x0 cmd_flags=0x2e1 cmd_retries=0 stop_opcode=0 stop_arg=0x0 >> stop_flags=0x0 stop_retries=0 sbc_opcode=0 sbc_arg=0x0 sbc_flags=0x0 >> sbc_retires=0 blocks=0 block_size=0 blk_addr=0 data_flags=0x0 tag=0 >> can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1 >> retune_period=0 >> <idle>-0 [000] d.h2. 8.164816: sdhci_cmd_irq: >> hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x10000 >> intmask_p=0x18000 >> irq/24-mmc2-96 [000] ..... 8.164840: sdhci_thread_irq: >> msg= >> irq/24-mmc2-96 [000] d.h2. 8.164896: sdhci_cmd_irq: >> hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x1 >> intmask_p=0x1 >> irq/24-mmc2-96 [000] ..... 8.285142: mmc_request_done: >> mmc2: end struct mmc_request[000000000d30cc0c]: cmd_opcode=5 >> cmd_err=-110 cmd_resp=0x0 0x0 0x0 0x0 cmd_retries=0 stop_opcode=0 >> stop_err=0 stop_resp=0x0 0x0 0x0 0x0 stop_retries=0 sbc_opcode=0 >> sbc_err=0 sbc_resp=0x0 0x0 0x0 0x0 sbc_retries=0 bytes_xfered=0 >> data_err=0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0 >> hold_retune=1 retune_period=0 >> >> Here's what happens: the __mmc_start_request function is called with >> opcode 5. Since the power to the Wi-Fi card, which resides on this SDIO >> bus, is initially off after the reset, an interrupt SDHCI_INT_TIMEOUT is >> triggered. Immediately after that, a second interrupt SDHCI_INT_RESPONSE >> is triggered. Depending on the exact timing, these conditions can >> trigger the following race problem: >> >> 1) The sdhci_cmd_irq top half handles the command as an error. It sets >> host->cmd to NULL and host->pending_reset to true. >> 2) The sdhci_thread_irq bottom half is scheduled next and executes faster >> than the second interrupt handler for SDHCI_INT_RESPONSE. It clears >> host->pending_reset before the SDHCI_INT_RESPONSE handler runs. >> 3) The pending interrupt SDHCI_INT_RESPONSE handler gets called, triggering >> a code path that prints: "mmc2: Got command interrupt 0x00000001 even >> though no command operation was in progress." >> >> To solve this issue, we need to clear pending interrupts when resetting >> host->pending_reset. This ensures that after sdhci_threaded_irq restores >> interrupts, there are no pending stale interrupts. >> >> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com> >> --- >> drivers/mmc/host/sdhci.c | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c >> index 4b91c9e96635..b91a6076c332 100644 >> --- a/drivers/mmc/host/sdhci.c >> +++ b/drivers/mmc/host/sdhci.c >> @@ -3098,6 +3098,10 @@ static bool sdhci_request_done(struct sdhci_host *host) >> sdhci_reset_for(host, REQUEST_ERROR); >> >> host->pending_reset = false; >> + >> + /* Clear any pending interrupts after reset */ >> + sdhci_writel(host, SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK, >> + SDHCI_INT_STATUS); > > According to SDHCI spec, "Software Reset For CMD Line" clears > "Command Complete" in "Normal Interrupt Status register", so the > interrupt status should not need to be cleared again. > > Which SDHCI driver is it? > Thank you for your review. The driver in use is located at drivers/mmc/host/sdhci-of-dwcmshc.c, and the .compatible string is thead,th1520-dwcmshc. Based on the specifications, it appears that the specific hardware used in the LicheePi4A SoC may not be fully compliant with the SDHCI standard. Therefore, the appropriate solution might be to add additional clearing code to the th1520_sdhci_reset() function. >> } >> >> /* > >
On 7/10/24 20:00, Michal Wilczynski wrote: > > > On 10/7/24 18:09, Adrian Hunter wrote: >> On 3/10/24 19:10, Michal Wilczynski wrote: >>> While working with the T-Head 1520 LicheePi4A SoC, certain conditions >>> arose that allowed me to reproduce a race issue in the sdhci code. >>> >>> To reproduce the bug, you need to enable the sdio1 controller in the >>> device tree file >>> `arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi` as follows: >>> >>> &sdio1 { >>> bus-width = <4>; >>> max-frequency = <100000000>; >>> no-sd; >>> no-mmc; >>> broken-cd; >>> cap-sd-highspeed; >>> post-power-on-delay-ms = <50>; >>> status = "okay"; >>> wakeup-source; >>> keep-power-in-suspend; >>> }; >>> >>> When resetting the SoC using the reset button, the following messages >>> appear in the dmesg log: >>> >>> [ 8.164898] mmc2: Got command interrupt 0x00000001 even though no >>> command operation was in progress. >>> [ 8.174054] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== >>> [ 8.180503] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000005 >>> [ 8.186950] mmc2: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 >>> [ 8.193395] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 >>> [ 8.199841] mmc2: sdhci: Present: 0x03da0000 | Host ctl: 0x00000000 >>> [ 8.206287] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 >>> [ 8.212733] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000decf >>> [ 8.219178] mmc2: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 >>> [ 8.225622] mmc2: sdhci: Int enab: 0x00ff1003 | Sig enab: 0x00ff1003 >>> [ 8.232068] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 >>> [ 8.238513] mmc2: sdhci: Caps: 0x3f69c881 | Caps_1: 0x08008177 >>> [ 8.244959] mmc2: sdhci: Cmd: 0x00000502 | Max curr: 0x00191919 >>> [ 8.254115] mmc2: sdhci: Resp[0]: 0x00001009 | Resp[1]: 0x00000000 >>> [ 8.260561] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 >>> [ 8.267005] mmc2: sdhci: Host ctl2: 0x00001000 >>> [ 8.271453] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: >>> 0x0000000000000000 >>> [ 8.278594] mmc2: sdhci: ============================================ >>> >>> I also enabled some traces to better understand the problem: >>> >>> kworker/3:1-62 [003] ..... 8.163538: mmc_request_start: >>> mmc2: start struct mmc_request[000000000d30cc0c]: cmd_opcode=5 >>> cmd_arg=0x0 cmd_flags=0x2e1 cmd_retries=0 stop_opcode=0 stop_arg=0x0 >>> stop_flags=0x0 stop_retries=0 sbc_opcode=0 sbc_arg=0x0 sbc_flags=0x0 >>> sbc_retires=0 blocks=0 block_size=0 blk_addr=0 data_flags=0x0 tag=0 >>> can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1 >>> retune_period=0 >>> <idle>-0 [000] d.h2. 8.164816: sdhci_cmd_irq: >>> hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x10000 >>> intmask_p=0x18000 >>> irq/24-mmc2-96 [000] ..... 8.164840: sdhci_thread_irq: >>> msg= >>> irq/24-mmc2-96 [000] d.h2. 8.164896: sdhci_cmd_irq: >>> hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x1 >>> intmask_p=0x1 >>> irq/24-mmc2-96 [000] ..... 8.285142: mmc_request_done: >>> mmc2: end struct mmc_request[000000000d30cc0c]: cmd_opcode=5 >>> cmd_err=-110 cmd_resp=0x0 0x0 0x0 0x0 cmd_retries=0 stop_opcode=0 >>> stop_err=0 stop_resp=0x0 0x0 0x0 0x0 stop_retries=0 sbc_opcode=0 >>> sbc_err=0 sbc_resp=0x0 0x0 0x0 0x0 sbc_retries=0 bytes_xfered=0 >>> data_err=0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0 >>> hold_retune=1 retune_period=0 >>> >>> Here's what happens: the __mmc_start_request function is called with >>> opcode 5. Since the power to the Wi-Fi card, which resides on this SDIO >>> bus, is initially off after the reset, an interrupt SDHCI_INT_TIMEOUT is >>> triggered. Immediately after that, a second interrupt SDHCI_INT_RESPONSE >>> is triggered. Depending on the exact timing, these conditions can >>> trigger the following race problem: >>> >>> 1) The sdhci_cmd_irq top half handles the command as an error. It sets >>> host->cmd to NULL and host->pending_reset to true. >>> 2) The sdhci_thread_irq bottom half is scheduled next and executes faster >>> than the second interrupt handler for SDHCI_INT_RESPONSE. It clears >>> host->pending_reset before the SDHCI_INT_RESPONSE handler runs. >>> 3) The pending interrupt SDHCI_INT_RESPONSE handler gets called, triggering >>> a code path that prints: "mmc2: Got command interrupt 0x00000001 even >>> though no command operation was in progress." >>> >>> To solve this issue, we need to clear pending interrupts when resetting >>> host->pending_reset. This ensures that after sdhci_threaded_irq restores >>> interrupts, there are no pending stale interrupts. >>> >>> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com> >>> --- >>> drivers/mmc/host/sdhci.c | 4 ++++ >>> 1 file changed, 4 insertions(+) >>> >>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c >>> index 4b91c9e96635..b91a6076c332 100644 >>> --- a/drivers/mmc/host/sdhci.c >>> +++ b/drivers/mmc/host/sdhci.c >>> @@ -3098,6 +3098,10 @@ static bool sdhci_request_done(struct sdhci_host *host) >>> sdhci_reset_for(host, REQUEST_ERROR); >>> >>> host->pending_reset = false; >>> + >>> + /* Clear any pending interrupts after reset */ >>> + sdhci_writel(host, SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK, >>> + SDHCI_INT_STATUS); >> >> According to SDHCI spec, "Software Reset For CMD Line" clears >> "Command Complete" in "Normal Interrupt Status register", so the >> interrupt status should not need to be cleared again. >> >> Which SDHCI driver is it? >> > > Thank you for your review. > > The driver in use is located at drivers/mmc/host/sdhci-of-dwcmshc.c, > and the .compatible string is thead,th1520-dwcmshc. > > Based on the specifications, it appears that the specific hardware used in > the LicheePi4A SoC may not be fully compliant with the SDHCI standard. > Therefore, the appropriate solution might be to add additional clearing > code to the th1520_sdhci_reset() function. > Seems reasonable
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 4b91c9e96635..b91a6076c332 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -3098,6 +3098,10 @@ static bool sdhci_request_done(struct sdhci_host *host) sdhci_reset_for(host, REQUEST_ERROR); host->pending_reset = false; + + /* Clear any pending interrupts after reset */ + sdhci_writel(host, SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK, + SDHCI_INT_STATUS); } /*
While working with the T-Head 1520 LicheePi4A SoC, certain conditions arose that allowed me to reproduce a race issue in the sdhci code. To reproduce the bug, you need to enable the sdio1 controller in the device tree file `arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi` as follows: &sdio1 { bus-width = <4>; max-frequency = <100000000>; no-sd; no-mmc; broken-cd; cap-sd-highspeed; post-power-on-delay-ms = <50>; status = "okay"; wakeup-source; keep-power-in-suspend; }; When resetting the SoC using the reset button, the following messages appear in the dmesg log: [ 8.164898] mmc2: Got command interrupt 0x00000001 even though no command operation was in progress. [ 8.174054] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 8.180503] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000005 [ 8.186950] mmc2: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 [ 8.193395] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 [ 8.199841] mmc2: sdhci: Present: 0x03da0000 | Host ctl: 0x00000000 [ 8.206287] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 [ 8.212733] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000decf [ 8.219178] mmc2: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 [ 8.225622] mmc2: sdhci: Int enab: 0x00ff1003 | Sig enab: 0x00ff1003 [ 8.232068] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 [ 8.238513] mmc2: sdhci: Caps: 0x3f69c881 | Caps_1: 0x08008177 [ 8.244959] mmc2: sdhci: Cmd: 0x00000502 | Max curr: 0x00191919 [ 8.254115] mmc2: sdhci: Resp[0]: 0x00001009 | Resp[1]: 0x00000000 [ 8.260561] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 [ 8.267005] mmc2: sdhci: Host ctl2: 0x00001000 [ 8.271453] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000 [ 8.278594] mmc2: sdhci: ============================================ I also enabled some traces to better understand the problem: kworker/3:1-62 [003] ..... 8.163538: mmc_request_start: mmc2: start struct mmc_request[000000000d30cc0c]: cmd_opcode=5 cmd_arg=0x0 cmd_flags=0x2e1 cmd_retries=0 stop_opcode=0 stop_arg=0x0 stop_flags=0x0 stop_retries=0 sbc_opcode=0 sbc_arg=0x0 sbc_flags=0x0 sbc_retires=0 blocks=0 block_size=0 blk_addr=0 data_flags=0x0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1 retune_period=0 <idle>-0 [000] d.h2. 8.164816: sdhci_cmd_irq: hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x10000 intmask_p=0x18000 irq/24-mmc2-96 [000] ..... 8.164840: sdhci_thread_irq: msg= irq/24-mmc2-96 [000] d.h2. 8.164896: sdhci_cmd_irq: hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x1 intmask_p=0x1 irq/24-mmc2-96 [000] ..... 8.285142: mmc_request_done: mmc2: end struct mmc_request[000000000d30cc0c]: cmd_opcode=5 cmd_err=-110 cmd_resp=0x0 0x0 0x0 0x0 cmd_retries=0 stop_opcode=0 stop_err=0 stop_resp=0x0 0x0 0x0 0x0 stop_retries=0 sbc_opcode=0 sbc_err=0 sbc_resp=0x0 0x0 0x0 0x0 sbc_retries=0 bytes_xfered=0 data_err=0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1 retune_period=0 Here's what happens: the __mmc_start_request function is called with opcode 5. Since the power to the Wi-Fi card, which resides on this SDIO bus, is initially off after the reset, an interrupt SDHCI_INT_TIMEOUT is triggered. Immediately after that, a second interrupt SDHCI_INT_RESPONSE is triggered. Depending on the exact timing, these conditions can trigger the following race problem: 1) The sdhci_cmd_irq top half handles the command as an error. It sets host->cmd to NULL and host->pending_reset to true. 2) The sdhci_thread_irq bottom half is scheduled next and executes faster than the second interrupt handler for SDHCI_INT_RESPONSE. It clears host->pending_reset before the SDHCI_INT_RESPONSE handler runs. 3) The pending interrupt SDHCI_INT_RESPONSE handler gets called, triggering a code path that prints: "mmc2: Got command interrupt 0x00000001 even though no command operation was in progress." To solve this issue, we need to clear pending interrupts when resetting host->pending_reset. This ensures that after sdhci_threaded_irq restores interrupts, there are no pending stale interrupts. Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com> --- drivers/mmc/host/sdhci.c | 4 ++++ 1 file changed, 4 insertions(+)