[v3,1/2] dt-bindings: mmc: Add YAML schemas for the generic MMC options

Commit Message

Maxime Ripard May 20, 2019, 8:14 a.m. UTC

The MMC controllers have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.

Reviewed-by: Rob Herring <[e-mail]>
Signed-off-by: Maxime Ripard <[e-mail]>

---

Changes from v2:
  - Add a note to mention where the description has moved
  - Add Rob's Reviewed-by

Changes from v1:

  - Added back the cd-inverted and wp-inverted note
  - Removed the dependency of cd-inverted and wp-inverted on cd-gpios and
    wp-gpios
  - Fixed typo in the title
  - Fixed default in the bus-width property
  - Fixed typo in the wp-inverted property
  - Removed redundant type on cd-debounce-delay-ms
  - Switched the dsr maximum to hex instead of decimal notation
---
 Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 358 +++++++-
 Documentation/devicetree/bindings/mmc/mmc.txt             | 178 +---
 2 files changed, 359 insertions(+), 177 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mmc/mmc-controller.yaml


base-commit: a188339ca5a396acc588e5851ed7e19f66b0ebd9

Comments

Ulf Hansson May 28, 2019, 8:40 a.m. UTC | #1

> +patternProperties:
> +  "^.*@[0-9]+$":
> +    properties:
> +      reg:
> +        items:
> +          - minimum: 0
> +            maximum: 7
> +            description:
> +              Must contain the SDIO function number of the function this
> +              subnode describes. A value of 0 denotes the memory SD
> +              function, values from 1 to 7 denote the SDIO functions.
> +
> +      broken-hpi:
> +        $ref: /schemas/types.yaml#/definitions/flag
> +        description:
> +          Use this to indicate that the mmc-card has a broken hpi
> +          implementation, and that hpi should not be used.
> +
> +    required:
> +      - reg
> +

[...]

> -Use of Function subnodes
> -------------------------
> -
> -On embedded systems the cards connected to a host may need additional
> -properties. These can be specified in subnodes to the host controller node.
> -The subnodes are identified by the standard 'reg' property.
> -Which information exactly can be specified depends on the bindings for the
> -SDIO function driver for the subnode, as specified by the compatible string.
> -
> -Required host node properties when using function subnodes:
> -- #address-cells: should be one. The cell is the slot id.
> -- #size-cells: should be zero.
> -
> -Required function subnode properties:
> -- reg: Must contain the SDIO function number of the function this subnode
> -       describes. A value of 0 denotes the memory SD function, values from
> -       1 to 7 denote the SDIO functions.
> -
> -Optional function subnode properties:
> -- compatible: name of SDIO function following generic names recommended practice
> -

I think most of the information of how we use sub(child) nodes
disappeared in this conversion - or at least gets harder to
understand. Could we perhaps keep some of this?

Kind regards
Uffe

Maxime Ripard May 28, 2019, 5:26 p.m. UTC | #2

Hi Ulf,

On Tue, May 28, 2019 at 10:40:16AM +0200, Ulf Hansson wrote:
> > +patternProperties:
> > +  "^.*@[0-9]+$":
> > +    properties:
> > +      reg:
> > +        items:
> > +          - minimum: 0
> > +            maximum: 7
> > +            description:
> > +              Must contain the SDIO function number of the function this
> > +              subnode describes. A value of 0 denotes the memory SD
> > +              function, values from 1 to 7 denote the SDIO functions.
> > +
> > +      broken-hpi:
> > +        $ref: /schemas/types.yaml#/definitions/flag
> > +        description:
> > +          Use this to indicate that the mmc-card has a broken hpi
> > +          implementation, and that hpi should not be used.
> > +
> > +    required:
> > +      - reg
> > +
>
> [...]
>
> > -Use of Function subnodes
> > -------------------------
> > -
> > -On embedded systems the cards connected to a host may need additional
> > -properties. These can be specified in subnodes to the host controller node.
> > -The subnodes are identified by the standard 'reg' property.
> > -Which information exactly can be specified depends on the bindings for the
> > -SDIO function driver for the subnode, as specified by the compatible string.
> > -
> > -Required host node properties when using function subnodes:
> > -- #address-cells: should be one. The cell is the slot id.
> > -- #size-cells: should be zero.
> > -
> > -Required function subnode properties:
> > -- reg: Must contain the SDIO function number of the function this subnode
> > -       describes. A value of 0 denotes the memory SD function, values from
> > -       1 to 7 denote the SDIO functions.
> > -
> > -Optional function subnode properties:
> > -- compatible: name of SDIO function following generic names recommended practice
> > -
>
> I think most of the information of how we use sub(child) nodes
> disappeared in this conversion - or at least gets harder to
> understand. Could we perhaps keep some of this?

Sure, what would you like to keep in particular?

Thanks!
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Ulf Hansson May 28, 2019, 7:32 p.m. UTC | #3

On Tue, 28 May 2019 at 19:26, Maxime Ripard <[e-mail]> wrote:
>
> Hi Ulf,
>
> On Tue, May 28, 2019 at 10:40:16AM +0200, Ulf Hansson wrote:
> > > +patternProperties:
> > > +  "^.*@[0-9]+$":
> > > +    properties:
> > > +      reg:
> > > +        items:
> > > +          - minimum: 0
> > > +            maximum: 7
> > > +            description:
> > > +              Must contain the SDIO function number of the function this
> > > +              subnode describes. A value of 0 denotes the memory SD
> > > +              function, values from 1 to 7 denote the SDIO functions.
> > > +
> > > +      broken-hpi:
> > > +        $ref: /schemas/types.yaml#/definitions/flag
> > > +        description:
> > > +          Use this to indicate that the mmc-card has a broken hpi
> > > +          implementation, and that hpi should not be used.
> > > +
> > > +    required:
> > > +      - reg
> > > +
> >
> > [...]
> >
> > > -Use of Function subnodes
> > > -------------------------
> > > -
> > > -On embedded systems the cards connected to a host may need additional
> > > -properties. These can be specified in subnodes to the host controller node.
> > > -The subnodes are identified by the standard 'reg' property.
> > > -Which information exactly can be specified depends on the bindings for the
> > > -SDIO function driver for the subnode, as specified by the compatible string.
> > > -
> > > -Required host node properties when using function subnodes:
> > > -- #address-cells: should be one. The cell is the slot id.
> > > -- #size-cells: should be zero.
> > > -
> > > -Required function subnode properties:
> > > -- reg: Must contain the SDIO function number of the function this subnode
> > > -       describes. A value of 0 denotes the memory SD function, values from
> > > -       1 to 7 denote the SDIO functions.
> > > -
> > > -Optional function subnode properties:
> > > -- compatible: name of SDIO function following generic names recommended practice
> > > -
> >
> > I think most of the information of how we use sub(child) nodes
> > disappeared in this conversion - or at least gets harder to
> > understand. Could we perhaps keep some of this?
>
> Sure, what would you like to keep in particular?

Most of it, so we can understand what can be described in sub-nodes.

Additionally, we should also include what is stated in
Documentation/devicetree/bindings/mmc/mmc-card.txt, as that also
refers to how subnodes should be used, when it has the "mmc-card"
compatible.

Or maybe we should simply move all things related to subnodes into a
separate .yaml?

Kind regards
Uffe

Maxime Ripard May 29, 2019, 7:42 a.m. UTC | #4

Hi!

On Tue, May 28, 2019 at 09:32:31PM +0200, Ulf Hansson wrote:
> On Tue, 28 May 2019 at 19:26, Maxime Ripard <[e-mail]> wrote:
> > On Tue, May 28, 2019 at 10:40:16AM +0200, Ulf Hansson wrote:
> > > > +patternProperties:
> > > > +  "^.*@[0-9]+$":
> > > > +    properties:
> > > > +      reg:
> > > > +        items:
> > > > +          - minimum: 0
> > > > +            maximum: 7
> > > > +            description:
> > > > +              Must contain the SDIO function number of the function this
> > > > +              subnode describes. A value of 0 denotes the memory SD
> > > > +              function, values from 1 to 7 denote the SDIO functions.
> > > > +
> > > > +      broken-hpi:
> > > > +        $ref: /schemas/types.yaml#/definitions/flag
> > > > +        description:
> > > > +          Use this to indicate that the mmc-card has a broken hpi
> > > > +          implementation, and that hpi should not be used.
> > > > +
> > > > +    required:
> > > > +      - reg
> > > > +
> > >
> > > [...]
> > >
> > > > -Use of Function subnodes
> > > > -------------------------
> > > > -
> > > > -On embedded systems the cards connected to a host may need additional
> > > > -properties. These can be specified in subnodes to the host controller node.
> > > > -The subnodes are identified by the standard 'reg' property.
> > > > -Which information exactly can be specified depends on the bindings for the
> > > > -SDIO function driver for the subnode, as specified by the compatible string.
> > > > -
> > > > -Required host node properties when using function subnodes:
> > > > -- #address-cells: should be one. The cell is the slot id.
> > > > -- #size-cells: should be zero.
> > > > -
> > > > -Required function subnode properties:
> > > > -- reg: Must contain the SDIO function number of the function this subnode
> > > > -       describes. A value of 0 denotes the memory SD function, values from
> > > > -       1 to 7 denote the SDIO functions.
> > > > -
> > > > -Optional function subnode properties:
> > > > -- compatible: name of SDIO function following generic names recommended practice
> > > > -
> > >
> > > I think most of the information of how we use sub(child) nodes
> > > disappeared in this conversion - or at least gets harder to
> > > understand. Could we perhaps keep some of this?
> >
> > Sure, what would you like to keep in particular?
>
> Most of it, so we can understand what can be described in sub-nodes.

I've pushed a new version that keeps everything, I guess.

> Additionally, we should also include what is stated in
> Documentation/devicetree/bindings/mmc/mmc-card.txt, as that also
> refers to how subnodes should be used, when it has the "mmc-card"
> compatible.
>
> Or maybe we should simply move all things related to subnodes into a
> separate .yaml?

Yeah, this should be a separate YAML schema.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Patch

diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
new file mode 100644
index 000000000000..a570b5261cc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
@@ -0,0 +1,358 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MMC Controller Generic Binding
+
+maintainers:
+  - Ulf Hansson <[e-mail]>
+
+description: |
+  These properties are common to multiple MMC host controllers. Any host
+  that requires the respective functionality should implement them using
+  these definitions.
+
+properties:
+  $nodename:
+    pattern: "^mmc(@.*)?$"
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  # Card Detection.
+  # If none of these properties are supplied, the host native card
+  # detect will be used. Only one of them should be provided.
+
+  broken-cd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      There is no card detection available; polling must be used.
+
+  cd-gpios:
+    description:
+      The card detection will be done using the GPIO provided.
+
+  non-removable:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Non-removable slot (like eMMC); assume always present.
+
+  # *NOTE* on CD and WP polarity. To use common for all SD/MMC host
+  # controllers line polarity properties, we have to fix the meaning
+  # of the "normal" and "inverted" line levels. We choose to follow
+  # the SDHCI standard, which specifies both those lines as "active
+  # low." Therefore, using the "cd-inverted" property means, that the
+  # CD line is active high, i.e. it is high, when a card is
+  # inserted. Similar logic applies to the "wp-inverted" property.
+  #
+  # CD and WP lines can be implemented on the hardware in one of two
+  # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
+  # as dedicated pins. Polarity of dedicated pins can be specified,
+  # using *-inverted properties. GPIO polarity can also be specified
+  # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
+  # latter case. We choose to use the XOR logic for GPIO CD and WP
+  # lines.  This means, the two properties are "superimposed," for
+  # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
+  # respective *-inverted property property results in a
+  # double-inversion and actually means the "normal" line polarity is
+  # in effect.
+  wp-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The Write Protect line polarity is inverted.
+
+  cd-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The CD line polarity is inverted.
+
+  # Other properties
+
+  bus-width:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 4, 8]
+        default: 1
+    description:
+      Number of data lines.
+
+  max-frequency:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 400000
+      - maximum: 200000000
+    description:
+      Maximum operating frequency of the bus.
+
+  disable-wp:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When set, no physical write-protect line is present. This
+      property should only be specified when the controller has a
+      dedicated write-protect detection logic. If a GPIO is always
+      used for the write-protect detection. If a GPIO is always used
+      for the write-protect detection logic, it is sufficient to not
+      specify the wp-gpios property in the absence of a write-protect
+      line.
+
+  wp-gpios:
+    description:
+      GPIO to use for the write-protect detection.
+
+  cd-debounce-delay-ms:
+    description:
+      Set delay time before detecting card after card insert
+      interrupt.
+
+  no-1-8-v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When specified, denotes that 1.8V card voltage is not supported
+      on this system, even if the controller claims it.
+
+  cap-sd-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD high-speed timing is supported.
+
+  cap-mmc-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      MMC high-speed timing is supported.
+
+  sd-uhs-sdr12:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR12 speed is supported.
+
+  sd-uhs-sdr25:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR25 speed is supported.
+
+  sd-uhs-sdr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR50 speed is supported.
+
+  sd-uhs-sdr104:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR104 speed is supported.
+
+  sd-uhs-ddr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS DDR50 speed is supported.
+
+  cap-power-off-card:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Powering off the card is safe.
+
+  cap-mmc-hw-reset:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC hardware reset is supported
+
+  cap-sdio-irq:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      enable SDIO IRQ signalling on this interface
+
+  full-pwr-cycle:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Full power cycle of the card is supported.
+
+  mmc-ddr-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.2V I/O) is supported.
+
+  mmc-ddr-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.8V I/O) is supported.
+
+  mmc-ddr-3_3v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (3.3V I/O) is supported.
+
+  mmc-hs200-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.2V I/O) is supported.
+
+  mmc-hs200-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.8V I/O) is supported.
+
+  mmc-hs400-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.2V I/O) is supported.
+
+  mmc-hs400-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.8V I/O) is supported.
+
+  mmc-hs400-enhanced-strobe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 enhanced strobe mode is supported
+
+  dsr:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 0xffff
+    description:
+      Value the card Driver Stage Register (DSR) should be programmed
+      with.
+
+  no-sdio:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SDIO commands during
+      initialization.
+
+  no-sd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SD commands during initialization.
+
+  no-mmc:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send MMC commands during
+      initialization.
+
+  fixed-emmc-driver-type:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 4
+    description:
+      For non-removable eMMC, enforce this driver type. The value is
+      the driver type as specified in the eMMC specification (table
+      206 in spec version 5.1)
+
+  post-power-on-delay-ms:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 10
+    description:
+      It was invented for MMC pwrseq-simple which could be referred to
+      mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay
+      waiting for I/O signalling and card power supply to be stable,
+      regardless of whether pwrseq-simple is used. Default to 10ms if
+      no available.
+
+  supports-cqe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the corresponding
+      MMC host controller supports HW command queue feature.
+
+  disable-cqe-dcmd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the MMC
+      controller\'s command queue engine (CQE) does not support direct
+      commands (DCMDs).
+
+  keep-power-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Preserves card power during a suspend/resume cycle.
+
+  # Deprecated: enable-sdio-wakeup
+  wakeup-source:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Enables wake up of host system on SDIO IRQ assertion.
+
+  vmmc-supply:
+    description:
+      Supply for the card power
+
+  vqmmc-supply:
+    description:
+      Supply for the bus IO line power
+
+  mmc-pwrseq:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      System-on-Chip designs may specify a specific MMC power
+      sequence. To successfully detect an (e)MMC/SD/SDIO card, that
+      power sequence must be maintained while initializing the card.
+
+patternProperties:
+  "^.*@[0-9]+$":
+    properties:
+      reg:
+        items:
+          - minimum: 0
+            maximum: 7
+            description:
+              Must contain the SDIO function number of the function this
+              subnode describes. A value of 0 denotes the memory SD
+              function, values from 1 to 7 denote the SDIO functions.
+
+      broken-hpi:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Use this to indicate that the mmc-card has a broken hpi
+          implementation, and that hpi should not be used.
+
+    required:
+      - reg
+
+dependencies:
+  cd-debounce-delay-ms: [ cd-gpios ]
+  fixed-emmc-driver-type: [ non-removable ]
+
+examples:
+  - |
+    sdhci@ab000000 {
+        compatible = "sdhci";
+        reg = <0xab000000 0x200>;
+        interrupts = <23>;
+        bus-width = <4>;
+        cd-gpios = <&gpio 69 0>;
+        cd-inverted;
+        wp-gpios = <&gpio 70 0>;
+        max-frequency = <50000000>;
+        keep-power-in-suspend;
+        wakeup-source;
+        mmc-pwrseq = <&sdhci0_pwrseq>;
+    };
+
+  - |
+    mmc3: mmc@1c12000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&mmc3_pins_a>;
+        vmmc-supply = <&reg_vmmc3>;
+        bus-width = <4>;
+        non-removable;
+        mmc-pwrseq = <&sdhci0_pwrseq>;
+
+        brcmf: bcrmf@1 {
+            reg = <1>;
+            compatible = "brcm,bcm43xx-fmac";
+            interrupt-parent = <&pio>;
+            interrupts = <10 8>;
+            interrupt-names = "host-wake";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index c269dbe384fe..bf9d7d3febf1 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -1,177 +1 @@ 
-These properties are common to multiple MMC host controllers. Any host
-that requires the respective functionality should implement them using
-these definitions.
-
-Interpreted by the OF core:
-- reg: Registers location and length.
-- interrupts: Interrupts used by the MMC controller.
-
-Card detection:
-If no property below is supplied, host native card detect is used.
-Only one of the properties in this section should be supplied:
-  - broken-cd: There is no card detection available; polling must be used.
-  - cd-gpios: Specify GPIOs for card detection, see gpio binding
-  - non-removable: non-removable slot (like eMMC); assume always present.
-
-Optional properties:
-- bus-width: Number of data lines, can be <1>, <4>, or <8>.  The default
-  will be <1> if the property is absent.
-- wp-gpios: Specify GPIOs for write protection, see gpio binding
-- cd-inverted: when present, polarity on the CD line is inverted. See the note
-  below for the case, when a GPIO is used for the CD line
-- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt.
-  It's only valid when cd-gpios is present.
-- wp-inverted: when present, polarity on the WP line is inverted. See the note
-  below for the case, when a GPIO is used for the WP line
-- disable-wp: When set no physical WP line is present. This property should
-  only be specified when the controller has a dedicated write-protect
-  detection logic. If a GPIO is always used for the write-protect detection
-  logic it is sufficient to not specify wp-gpios property in the absence of a WP
-  line.
-- max-frequency: maximum operating clock frequency
-- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
-  this system, even if the controller claims it is.
-- cap-sd-highspeed: SD high-speed timing is supported
-- cap-mmc-highspeed: MMC high-speed timing is supported
-- sd-uhs-sdr12: SD UHS SDR12 speed is supported
-- sd-uhs-sdr25: SD UHS SDR25 speed is supported
-- sd-uhs-sdr50: SD UHS SDR50 speed is supported
-- sd-uhs-sdr104: SD UHS SDR104 speed is supported
-- sd-uhs-ddr50: SD UHS DDR50 speed is supported
-- cap-power-off-card: powering off the card is safe
-- cap-mmc-hw-reset: eMMC hardware reset is supported
-- cap-sdio-irq: enable SDIO IRQ signalling on this interface
-- full-pwr-cycle: full power cycle of the card is supported
-- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported
-- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
-- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported
-- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported
-- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
-- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
-- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
-- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported
-- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
-  programmed with. Valid range: [0 .. 0xffff].
-- no-sdio: controller is limited to send sdio cmd during initialization
-- no-sd: controller is limited to send sd cmd during initialization
-- no-mmc: controller is limited to send mmc cmd during initialization
-- fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type.
-  The value <n> is the driver type as specified in the eMMC specification
-  (table 206 in spec version 5.1).
-- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could
-  be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay
-  waiting for I/O signalling and card power supply to be stable, regardless of
-  whether pwrseq-simple is used. Default to 10ms if no available.
-- supports-cqe : The presence of this property indicates that the corresponding
-  MMC host controller supports HW command queue feature.
-- disable-cqe-dcmd: This property indicates that the MMC controller's command
-  queue engine (CQE) does not support direct commands (DCMDs).
-
-*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
-polarity properties, we have to fix the meaning of the "normal" and "inverted"
-line levels. We choose to follow the SDHCI standard, which specifies both those
-lines as "active low." Therefore, using the "cd-inverted" property means, that
-the CD line is active high, i.e. it is high, when a card is inserted. Similar
-logic applies to the "wp-inverted" property.
-
-CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
-specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
-dedicated pins can be specified, using *-inverted properties. GPIO polarity can
-also be specified using the GPIO_ACTIVE_LOW flag. This creates an ambiguity
-in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
-This means, the two properties are "superimposed," for example leaving the
-GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted property
-property results in a double-inversion and actually means the "normal" line
-polarity is in effect.
-
-Optional SDIO properties:
-- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
-- wakeup-source: Enables wake up of host system on SDIO IRQ assertion
-		 (Legacy property supported: "enable-sdio-wakeup")
-
-MMC power
----------
-
-Controllers may implement power control from both the connected cards and
-the IO signaling (for example to change to high-speed 1.8V signalling). If
-the system supports this, then the following two properties should point
-to valid regulator nodes:
-
-- vqmmc-supply: supply node for IO line power
-- vmmc-supply: supply node for card's power
-
-
-MMC power sequences:
---------------------
-
-System on chip designs may specify a specific MMC power sequence. To
-successfully detect an (e)MMC/SD/SDIO card, that power sequence must be
-maintained while initializing the card.
-
-Optional property:
-- mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*"
-	for documentation of MMC power sequence bindings.
-
-
-Use of Function subnodes
-------------------------
-
-On embedded systems the cards connected to a host may need additional
-properties. These can be specified in subnodes to the host controller node.
-The subnodes are identified by the standard 'reg' property.
-Which information exactly can be specified depends on the bindings for the
-SDIO function driver for the subnode, as specified by the compatible string.
-
-Required host node properties when using function subnodes:
-- #address-cells: should be one. The cell is the slot id.
-- #size-cells: should be zero.
-
-Required function subnode properties:
-- reg: Must contain the SDIO function number of the function this subnode
-       describes. A value of 0 denotes the memory SD function, values from
-       1 to 7 denote the SDIO functions.
-
-Optional function subnode properties:
-- compatible: name of SDIO function following generic names recommended practice
-
-
-Examples
---------
-
-Basic example:
-
-sdhci@ab000000 {
-	compatible = "sdhci";
-	reg = <0xab000000 0x200>;
-	interrupts = <23>;
-	bus-width = <4>;
-	cd-gpios = <&gpio 69 0>;
-	cd-inverted;
-	wp-gpios = <&gpio 70 0>;
-	max-frequency = <50000000>;
-	keep-power-in-suspend;
-	wakeup-source;
-	mmc-pwrseq = <&sdhci0_pwrseq>
-}
-
-Example with sdio function subnode:
-
-mmc3: mmc@1c12000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins_a>;
-	vmmc-supply = <&reg_vmmc3>;
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&sdhci0_pwrseq>
-
-	brcmf: bcrmf@1 {
-		reg = <1>;
-		compatible = "brcm,bcm43xx-fmac";
-		interrupt-parent = <&pio>;
-		interrupts = <10 8>; /* PH10 / EINT10 */
-		interrupt-names = "host-wake";
-	};
-};
+This file has moved to mmc-controller.yaml.