diff mbox

[1/1] ARM: OMAP3: Revert "Make I2C bus 2 configurable for BeagleBoard"

Message ID 1235320967-5614-2-git-send-email-jarkko.nikula@nokia.com (mailing list archive)
State Accepted
Commit 5fc0a8253b0e10baa0f60fccdfad1ce30858db3f
Delegated to: Tony Lindgren
Headers show

Commit Message

Jarkko Nikula Feb. 22, 2009, 4:42 p.m. UTC
This is manual revert for commit bae4b6a716ccf3247a1991d3c20b5e58ddd52890.
CONFIG_I2C2_OMAP_BEAGLE is not needed anymore since additional busses can be
registered on the command line by the commit

This change makes drivers/i2c/busses/Kconfig sync with the mainline.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Dirk Behme <dirk.behme@gmail.com>
 arch/arm/mach-omap2/board-omap3beagle.c |    3 ---
 drivers/i2c/busses/Kconfig              |   20 ++------------------
 2 files changed, 2 insertions(+), 21 deletions(-)
diff mbox


diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index eb261af..af21a91 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -240,9 +240,6 @@  static int __init omap3_beagle_i2c_init(void)
 	omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
-	omap_register_i2c_bus(2, 400, NULL, 0);
 	/* Bus 3 is attached to the DVI port where devices like the pico DLP
 	 * projector don't work reliably with 400kHz */
 	omap_register_i2c_bus(3, 100, NULL, 0);
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 4b8f400..7f95905 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -418,26 +418,10 @@  config I2C_OMAP
 	default y if MACH_OMAP_H3 || MACH_OMAP_OSK
 	  If you say yes to this option, support will be included for the
-	  I2C interface on the Texas Instruments OMAP1/2/3 family of
-	  processors.
-	  Like OMAP1510/1610/1710/5912, OMAP242x, OMAP34x and OMAP35x.
+	  I2C interface on the Texas Instruments OMAP1/2 family of processors.
+	  Like OMAP1510/1610/1710/5912 and OMAP242x.
 	  For details see http://www.ti.com/omap.
-config I2C2_OMAP_BEAGLE
-	bool "Enable I2C2 for OMAP3 BeagleBoard"
-	select OMAP_MUX
-	default n
-	help
-	  Say Y here if you want to enable I2C bus 2 at OMAP3 based
-	  BeagleBoard.
-	  I2C2 at BeagleBoard is connected to expansion connector, i.e. unused
-	  if nothing is connected to this connector. As internal OMAP3 pull up
-	  resistors are not strong enough, enabled but unused I2C2 bus results
-	  in error messages (e.g. I2C timeouts). Enable this only if you have
-	  something connected to I2C2 at board's expansion connector and this
-	  extension has additional pull up resistors for I2C2 bus.
 config I2C_PASEMI
 	tristate "PA Semi SMBus interface"
 	depends on PPC_PASEMI && PCI