@@ -87,3 +87,4 @@ obj-y += $(onenand-m) $(onenand-y)
smc91x-$(CONFIG_SMC91X) := gpmc-smc91x.o
obj-y += $(smc91x-m) $(smc91x-y)
+obj-$(CONFIG_OMAP_HSI_DEVICE) += hsi.o
new file mode 100644
@@ -0,0 +1,497 @@
+/*
+ * arch/arm/mach-omap2/hsi.c
+ *
+ * HSI device definition
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Author: Sebastien JAN <s-jan@ti.com>
+ *
+ * This package is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
+ * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
+ */
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/jiffies.h>
+#include <linux/notifier.h>
+#include <mach/clock.h>
+#include <mach/hsi.h>
+#include <linux/hsi_driver_if.h>
+#include "clock.h"
+#include <asm/clkdev.h>
+#include <mach/mux.h>
+
+#define hsi_inl(p) inl((unsigned long) p)
+#define hsi_outl(v, p) outl(v, (unsigned long) p)
+
+/**
+ * struct hsi_internal_clk - Generic virtual hsi clock
+ * @clk: clock data
+ * @nb: notfier block for the DVFS notification chain
+ * @childs: Array of HSI FCK and ICK clocks
+ * @n_childs: Number of clocks in childs array
+ * @rate_change: Tracks if we are in the middle of a clock rate change
+ * @pdev: Reference to the HSI platform device associated to the clock
+ * @drv_nb: Reference to driver nb, use to propagate the DVFS notification
+ */
+struct hsi_internal_clk {
+ struct clk clk;
+ struct notifier_block nb;
+
+ struct clk **childs;
+ int n_childs;
+
+ unsigned int rate_change:1;
+
+ struct platform_device *pdev;
+ struct notifier_block *drv_nb;
+};
+
+static void hsi_set_mode(struct platform_device *pdev, u32 mode)
+{
+ struct hsi_platform_data *pdata = pdev->dev.platform_data;
+ void __iomem *base = OMAP2_IO_ADDRESS(pdev->resource[0].start);
+ int port;
+
+ for (port = 1; port <= pdata->num_ports; port++) {
+ /* FIXME - to update: need read/modify/write or something else:
+ * this register now also contains flow and wake ctrl
+ */
+ hsi_outl(mode, base + HSI_HST_MODE_REG(port));
+ hsi_outl(mode, base + HSI_HSR_MODE_REG(port));
+ }
+}
+
+static void hsi_save_mode(struct platform_device *pdev)
+{
+ struct hsi_platform_data *pdata = pdev->dev.platform_data;
+ void __iomem *base = OMAP2_IO_ADDRESS(pdev->resource[0].start);
+ struct port_ctx *p;
+ int port;
+
+ for (port = 1; port <= pdata->num_ports; port++) {
+ p = &pdata->ctx.pctx[port - 1];
+ p->hst.mode = hsi_inl(base + HSI_HST_MODE_REG(port));
+ p->hsr.mode = hsi_inl(base + HSI_HSR_MODE_REG(port));
+ }
+}
+
+static void hsi_restore_mode(struct platform_device *pdev)
+{
+ struct hsi_platform_data *pdata = pdev->dev.platform_data;
+ void __iomem *base = OMAP2_IO_ADDRESS(pdev->resource[0].start);
+ struct port_ctx *p;
+ int port;
+
+ for (port = 1; port <= pdata->num_ports; port++) {
+ p = &pdata->ctx.pctx[port - 1];
+ hsi_outl(p->hst.mode, base + HSI_HST_MODE_REG(port));
+ hsi_outl(p->hsr.mode, base + HSI_HSR_MODE_REG(port));
+ }
+}
+
+static int hsi_clk_event(struct notifier_block *nb, unsigned long event,
+ void *data)
+{
+/* FIXME
+ struct hsi_internal_clk *hsi_clk =
+ container_of(nb, struct hsi_internal_clk, nb);
+ switch (event) {
+ case CLK_PRE_RATE_CHANGE:
+ hsi_clk->drv_nb->notifier_call(hsi_clk->drv_nb, event, data);
+ hsi_clk->rate_change = 1;
+ if (hsi_clk->clk.usecount > 0) {
+ hsi_save_mode(hsi_clk->pdev);
+ hsi_set_mode(hsi_clk->pdev, HSI_MODE_SLEEP);
+ }
+ break;
+ case CLK_ABORT_RATE_CHANGE:
+ case CLK_POST_RATE_CHANGE:
+ if ((hsi_clk->clk.usecount > 0) && (hsi_clk->rate_change))
+ hsi_restore_mode(hsi_clk->pdev);
+
+ hsi_clk->rate_change = 0;
+ hsi_clk->drv_nb->notifier_call(hsi_clk->drv_nb, event, data);
+ break;
+ default:
+ break;
+ }
+*/
+ return NOTIFY_DONE;
+}
+
+static int hsi_clk_notifier_register(struct clk *clk, struct notifier_block *nb)
+{
+/* FIXME : clock functions not handled yet on OMAP4
+ struct hsi_internal_clk *hsi_clk;
+ if (!clk || !nb) {
+ return -EINVAL;
+ }
+ hsi_clk = container_of(clk, struct hsi_internal_clk, clk);
+ hsi_clk->drv_nb = nb;
+ hsi_clk->nb.priority = nb->priority;
+*/
+ /* NOTE: We only want notifications from the functional clock */
+/* FIXME
+ return clk_notifier_register(hsi_clk->childs[1], &hsi_clk->nb);
+*/
+ pr_debug("%s called\n", __func__);
+ return 0;
+}
+
+static int hsi_clk_notifier_unregister(struct clk *clk,
+ struct notifier_block *nb)
+{
+/* FIXME : clock functions not handled yet on OMAP4
+ struct hsi_internal_clk *hsi_clk;
+
+ if (!clk || !nb)
+ return -EINVAL;
+
+ hsi_clk = container_of(clk, struct hsi_internal_clk, clk);
+ hsi_clk->drv_nb = NULL;
+
+ return clk_notifier_unregister(hsi_clk->childs[1], &hsi_clk->nb);
+*/
+ pr_debug(KERN_DEBUG "%s called", __func__);
+ return 0;
+}
+
+static void hsi_save_ctx(struct platform_device *pdev)
+{
+ struct hsi_platform_data *pdata = pdev->dev.platform_data;
+ void __iomem *base = OMAP2_IO_ADDRESS(pdev->resource[0].start);
+ struct port_ctx *p;
+ int port;
+
+/* FIXME - implement PM support
+ pdata->ctx.loss_count =
+ omap_pm_get_dev_context_loss_count(&pdev->dev);
+*/
+ pdata->ctx.sysconfig = hsi_inl(base + HSI_SYS_SYSCONFIG_REG);
+ pdata->ctx.gdd_gcr = hsi_inl(base + HSI_GDD_GCR_REG);
+ for (port = 1; port <= pdata->num_ports; port++) {
+ p = &pdata->ctx.pctx[port - 1];
+ p->sys_mpu_enable[0] = hsi_inl(base +
+ HSI_SYS_MPU_ENABLE_REG(port, 0));
+ p->sys_mpu_enable[1] = hsi_inl(base +
+ HSI_SYS_MPU_U_ENABLE_REG(port, 0));
+ p->hst.frame_size = hsi_inl(base +
+ HSI_HST_FRAMESIZE_REG(port));
+ p->hst.divisor = hsi_inl(base + HSI_HST_DIVISOR_REG(port));
+ p->hst.channels = hsi_inl(base + HSI_HST_CHANNELS_REG(port));
+ p->hst.arb_mode = hsi_inl(base + HSI_HST_ARBMODE_REG(port));
+ p->hsr.frame_size = hsi_inl(base +
+ HSI_HSR_FRAMESIZE_REG(port));
+/*FIXME - check this register*/
+ p->hsr.timeout = hsi_inl(base + HSI_HSR_COUNTERS_REG(port));
+ p->hsr.channels = hsi_inl(base + HSI_HSR_CHANNELS_REG(port));
+ }
+}
+
+static void hsi_restore_ctx(struct platform_device *pdev)
+{
+ struct hsi_platform_data *pdata = pdev->dev.platform_data;
+ void __iomem *base = OMAP2_IO_ADDRESS(pdev->resource[0].start);
+ struct port_ctx *p;
+ int port;
+/* FIXME - implement PM support
+ int loss_count;
+
+ loss_count = omap_pm_get_dev_context_loss_count(&pdev->dev);
+
+ if (loss_count == pdata->ctx.loss_count)
+ return;
+*/
+ hsi_outl(pdata->ctx.sysconfig, base + HSI_SYS_SYSCONFIG_REG);
+ hsi_outl(pdata->ctx.gdd_gcr, base + HSI_GDD_GCR_REG);
+ for (port = 1; port <= pdata->num_ports; port++) {
+ p = &pdata->ctx.pctx[port - 1];
+ hsi_outl(p->sys_mpu_enable[0], base +
+ HSI_SYS_MPU_ENABLE_REG(port, 0));
+ hsi_outl(p->sys_mpu_enable[1], base +
+ HSI_SYS_MPU_U_ENABLE_REG(port, 0));
+ hsi_outl(p->hst.frame_size, base +
+ HSI_HST_FRAMESIZE_REG(port));
+ hsi_outl(p->hst.divisor, base + HSI_HST_DIVISOR_REG(port));
+ hsi_outl(p->hst.channels, base + HSI_HST_CHANNELS_REG(port));
+ hsi_outl(p->hst.arb_mode, base + HSI_HST_ARBMODE_REG(port));
+ hsi_outl(p->hsr.frame_size, base +
+ HSI_HSR_FRAMESIZE_REG(port));
+/* FIXME - check this register */
+ hsi_outl(p->hsr.timeout, base + HSI_HSR_COUNTERS_REG(port));
+ hsi_outl(p->hsr.channels, base + HSI_HSR_CHANNELS_REG(port));
+ }
+}
+
+static void hsi_pdev_release(struct device *dev)
+{
+}
+
+/*
+ * NOTE: We abuse a little bit the struct port_ctx to use it also for
+ * initialization.
+ */
+static struct port_ctx hsi_port_ctx[] = {
+ [0] = {
+ .hst.mode = HSI_MODE_FRAME,
+ .hst.flow = HSI_FLOW_SYNCHRONIZED,
+ .hst.frame_size = HSI_FRAMESIZE_DEFAULT,
+ .hst.divisor = 1,
+ .hst.channels = HSI_CHANNELS_DEFAULT,
+ .hst.arb_mode = HSI_ARBMODE_ROUNDROBIN,
+ .hsr.mode = HSI_MODE_FRAME,
+ .hsr.flow = HSI_FLOW_SYNCHRONIZED,
+ .hsr.frame_size = HSI_FRAMESIZE_DEFAULT,
+ .hsr.channels = HSI_CHANNELS_DEFAULT,
+ .hsr.divisor = 0,
+ .hsr.timeout = HSI_COUNTERS_FT_DEFAULT |
+ HSI_COUNTERS_TB_DEFAULT |
+ HSI_COUNTERS_FB_DEFAULT,
+ },
+};
+
+static struct hsi_platform_data hsi_pdata = {
+ .num_ports = ARRAY_SIZE(hsi_port_ctx),
+ .ctx.pctx = hsi_port_ctx,
+ .clk_notifier_register = hsi_clk_notifier_register,
+ .clk_notifier_unregister = hsi_clk_notifier_unregister,
+};
+
+static struct resource hsi_resources[] = {
+ [0] = {
+ .start = 0x4A058000,
+ .end = 0x4A05b950,
+ .name = "omap_hsi_iomem",
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = INT_44XX_HSI_1_IRQ0,
+ .end = INT_44XX_HSI_1_IRQ0,
+ .name = "hsi_p1_mpu_irq0",
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = INT_44XX_HSI_2_IRQ1,
+ .end = INT_44XX_HSI_2_IRQ1,
+ .name = "hsi_p2_mpu_irq0",
+ .flags = IORESOURCE_IRQ,
+ },
+ [3] = {
+ .start = INT_44XX_HSI_1_DMAIRQ,
+ .end = INT_44XX_HSI_1_DMAIRQ,
+ .name = "hsi_gdd",
+ .flags = IORESOURCE_IRQ,
+ },
+ [4] = {
+ .start = 16, /* DMA channels available */
+ .end = 16,
+ .name = "hsi_gdd_chan_count",
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device hsi_pdev = {
+ .name = "omap_hsi",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(hsi_resources),
+ .resource = hsi_resources,
+ .dev = {
+ .release = hsi_pdev_release,
+ .platform_data = &hsi_pdata,
+ },
+};
+
+#ifdef CONFIG_OMAP_HSI_POWER_MANAGEMENT
+#define __HSI_CLK_FIX__
+#ifdef __HSI_CLK_FIX__
+/*
+ * FIXME: TO BE REMOVED.
+ * This hack allows us to ensure that clocks are stable before accehsing
+ * HSI controller registers. To be removed when PM functionalty is in place.
+ */
+static int check_hsi_active(void)
+{
+ u32 reg;
+ unsigned long dl = jiffies + msecs_to_jiffies(500);
+ void __iomem *cm_idlest1 = OMAP2_IO_ADDRESS(0x48004a20);
+
+ reg = inl(cm_idlest1);
+ while ((!(reg & 0x01)) && (time_before(jiffies, dl)))
+ reg = inl(cm_idlest1);
+
+ if (!(reg & 0x01)) { /* HST */
+ pr_err("HSI is still in STANDBY ! (BUG !?)\n");
+ return -1;
+ }
+
+ return 0;
+}
+#endif /* __HSI_CLK_FIX__ */
+#endif
+
+static int hsi_clk_init(struct hsi_internal_clk *hsi_clk)
+{
+/* FIXME - update clock names on OMAP4*/
+ const char *clk_names[] = {};
+
+ int i;
+ int j;
+
+ hsi_clk->n_childs = ARRAY_SIZE(clk_names);
+ hsi_clk->childs = kzalloc(hsi_clk->n_childs * sizeof(*hsi_clk->childs),
+ GFP_KERNEL);
+ if (!hsi_clk->childs)
+ return -ENOMEM;
+
+ for (i = 0; i < hsi_clk->n_childs; i++) {
+ hsi_clk->childs[i] = clk_get(&hsi_clk->pdev->dev, clk_names[i]);
+ if (IS_ERR(hsi_clk->childs[i])) {
+ pr_err("Unable to get HSI clock: %s", clk_names[i]);
+ for (j = i - 1; j >= 0; j--)
+ clk_put(hsi_clk->childs[j]);
+ return -ENODEV;
+ }
+ }
+
+ return 0;
+}
+
+
+
+static int hsi_clk_enable(struct clk *clk)
+{
+ struct hsi_internal_clk *hsi_clk =
+ container_of(clk, struct hsi_internal_clk, clk);
+/* FIXME - implement PM support
+ int err;
+ int i;
+
+ for (i = 0; i < hsi_clk->n_childs; i++) {
+ err = omap2_clk_enable(hsi_clk->childs[i]);
+ if (unlikely(err < 0))
+ goto rollback;
+ }
+*/
+#ifdef __HSI_CLK_FIX__
+ /*
+ * FIXME: To be removed
+ * Wait until the HSI controller has the clocks stable
+ */
+ check_hsi_active();
+#endif
+ hsi_restore_ctx(hsi_clk->pdev);
+ if (!hsi_clk->rate_change)
+ hsi_restore_mode(hsi_clk->pdev);
+
+ return 0;
+/* FIXME - implement PM support
+rollback:
+ pr_err("Error on HSI clk child %d\n", i);
+ for (i = i - 1; i >= 0; i--)
+ omap2_clk_disable(hsi_clk->childs[i]);
+ return err;
+*/
+}
+
+static void hsi_clk_disable(struct clk *clk)
+{
+ struct hsi_internal_clk *hsi_clk =
+ container_of(clk, struct hsi_internal_clk, clk);
+/* int i;*/
+
+ if (!hsi_clk->rate_change) {
+ hsi_save_mode(hsi_clk->pdev);
+ hsi_set_mode(hsi_clk->pdev, HSI_MODE_SLEEP);
+ }
+ /* Save ctx in all ports */
+ hsi_save_ctx(hsi_clk->pdev);
+
+/* FIXME - implement PM support
+ for (i = 0; i < hsi_clk->n_childs; i++)
+ omap2_clk_disable(hsi_clk->childs[i]);
+*/
+}
+
+static const int omap44xx_hsi_pins[] = {
+ AE18_4430_HSI1_CAWAKE,
+ AG19_4430_HSI1_CADATA,
+ AF19_4430_HSI1_CAFLAG,
+ AE19_4430_HSI1_ACREADY,
+ AF18_4430_HSI1_ACWAKE,
+ AG18_4430_HSI1_ACDATA,
+ AE17_4430_HSI1_ACFLAG,
+ AF17_4430_HSI1_CAREADY,
+};
+
+/* Mux settings for OMAP4430 */
+void omap_hsi_mux_setup(void)
+{
+ int i;
+ for (i = 0; i < ARRAY_SIZE(omap44xx_hsi_pins); i++)
+ omap_cfg_reg(omap44xx_hsi_pins[i]);
+ pr_debug("Pin muxing for HSI support done\n");
+}
+
+static const struct clkops clkops_hsi = {
+ .enable = hsi_clk_enable,
+ .disable = hsi_clk_disable,
+};
+
+static struct hsi_internal_clk hsi_clock = {
+ .clk = {
+ .name = "hsi_clk",
+ .id = -1,
+ .clkdm_name = "core_l4_clkdm",
+ .ops = &clkops_hsi,
+ },
+ .nb = {
+ .notifier_call = hsi_clk_event,
+ .priority = INT_MAX,
+ },
+ .pdev = &hsi_pdev,
+};
+
+/* FIXME - implement PM support
+static struct clk_lookup hsi_lk = {
+ .dev_id = NULL,
+ .con_id = "hsi_clk",
+ .clk = &hsi_clock.clk,
+};
+*/
+
+static int __init omap_hsi_init(void)
+{
+ int err;
+ struct clk *hsi_clk = &hsi_clock.clk;
+
+ hsi_clk_init(&hsi_clock);
+ clk_preinit(hsi_clk);
+/* FIXME - implement PM support
+ clkdev_add(&hsi_lk);
+*/
+ clk_register(hsi_clk);
+/* FIXME - implement PM support
+ omap2_init_clk_clkdm(hsi_clk);
+*/
+ err = platform_device_register(&hsi_pdev);
+ if (err < 0) {
+ pr_err("Unable to register HSI platform device: %d\n", err);
+ return err;
+ }
+
+ omap_hsi_mux_setup();
+
+ pr_info("HSI: device registered\n");
+ return 0;
+}
+subsys_initcall(omap_hsi_init);
new file mode 100644
@@ -0,0 +1,432 @@
+/*
+ * /mach/hsi.h
+ *
+ * Hardware definitions for HSI and SSI.
+ *
+ * Copyright (C) 2007-2008 Nokia Corporation. All rights reserved.
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Author: Carlos Chinea <carlos.chinea@nokia.com>
+ * Author: Sebastien JAN <s-jan@ti.com>
+ *
+ * This package is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
+ * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
+ */
+
+/* NOTE: This file defines the registers address offsets for both the
+ * SSI and HSI devices. Most of the registers share the same offset between
+ * these devices.
+ * When common or HSI only, the constants are name HSI*. Else the SSI specific
+ * constants are name HSI_SSI*
+ */
+
+#ifndef __HSI_H__
+#define __HSI_H__
+
+#define HSI_PORT_OFFSET 0x1000
+
+/*
+ * GDD base addr : 0x48059000 (SSI)
+ * GDD base addr : 0x4A059000 (HSI)
+ */
+#define HSI_GDD_OFFSET 0x1000
+#define HSI_GDD_BASE HSI_GDD_OFFSET /* 0x9000 */
+
+/*
+ * HST base addr:
+ * port 1: 0x4805a000 (SSI) - 0x4A05a000 (HSI)
+ * port 2: 0x4805b000 (SSI) - 0x4a05b000 (HSI)
+ */
+#define HSI_HST_OFFSET 0x2000
+#define HSI_HST_BASE(port) (HSI_HST_OFFSET + ((port - 1) *\
+ (HSI_PORT_OFFSET)))
+/*
+ * HSR base addr:
+ * port 1: 0x4805a800 (SSI) - 0x4A05a800 (HSI)
+ * port 2: 0x4805b800 (SSI) - 0x4A05b800 (HSI)
+ */
+#define HSI_HSR_OFFSET 0x2800
+#define HSI_HSR_BASE(port) (HSI_HSR_OFFSET + ((port - 1) *\
+ (HSI_PORT_OFFSET)))
+/*
+ * HSI SYS registers
+ */
+#define HSI_SYS_REVISION_REG 0x0000
+#define HSI_SSI_REV_MASK 0x000000ff
+#define HSI_SSI_REV_MAJOR 0xf0
+#define HSI_SSI_REV_MINOR 0x0f
+
+#define HSI_SYS_SYSCONFIG_REG 0x0010
+#define HSI_AUTOIDLE (1 << 0)
+#define HSI_SOFTRESET (1 << 1)
+#define HSI_FREE_EMU (1 << 2) /* Only for HSI */
+#define HSI_SIDLEMODE_FORCE 0
+#define HSI_SIDLEMODE_NO (1 << 3)
+#define HSI_SIDLEMODE_SMART (1 << 4)
+#define HSI_SIDLEMODE_MASK 0x00000018
+#define HSI_MIDLEMODE_FORCE 0
+#define HSI_MIDLEMODE_NO (1 << 12)
+#define HSI_MIDLEMODE_SMART (1 << 13)
+#define HSI_MIDLEMODE_MASK 0x00003000
+
+#define HSI_SYS_SYSSTATUS_REG 0x0014
+#define HSI_RESETDONE 1
+
+#define HSI_SYS_MPU_STATUS_BASE 0x0808
+#define HSI_SYS_MPU_STATUS_PORT_OFFSET 0x10
+#define HSI_SYS_MPU_STATUS_IRQ_OFFSET 8
+
+#define HSI_SYS_MPU_STATUS_REG(port, irq) \
+ (HSI_SYS_MPU_STATUS_BASE + \
+ (((port - 1) * HSI_SYS_MPU_STATUS_PORT_OFFSET) +\
+ (irq * HSI_SYS_MPU_STATUS_IRQ_OFFSET)))
+
+#define HSI_SYS_MPU_ENABLE_BASE 0x080c
+#define HSI_SYS_MPU_ENABLE_PORT_OFFSET 0x10
+#define HSI_SYS_MPU_ENABLE_IRQ_OFFSET 8
+
+#define HSI_SYS_MPU_ENABLE_REG(port, irq) \
+ (HSI_SYS_MPU_ENABLE_BASE + \
+ (((port - 1) * HSI_SYS_MPU_ENABLE_PORT_OFFSET) +\
+ (irq * HSI_SYS_MPU_ENABLE_IRQ_OFFSET)))
+#define HSI_HST_DATAACCEPT(channel) ((channel < 8) ? \
+ (1 << channel) : (1 << (channel - 8)))
+#define HSI_HSR_DATAAVAILABLE(channel) (channel < 8 ? \
+ (1 << (channel + 8)) : (1 << (channel - 8 + 8)))
+#define HSI_HSR_DATAOVERRUN(channel) (channel < 8 ? \
+ (1 << (channel + 16)) : (1 << (channel - 8 + 16)))
+#define HSI_ERROROCCURED (1 << 24)
+#define HSI_BREAKDETECTED (1 << 25)
+
+#define HSI_SYS_GDD_MPU_IRQ_STATUS_REG 0x0800
+#define HSI_SYS_GDD_MPU_IRQ_ENABLE_REG 0x0804
+#define HSI_GDD_LCH(channel) (1 << channel)
+
+#define HSI_SYS_WAKE_OFFSET 0x10
+#define HSI_SYS_WAKE_BASE 0x0c00
+#define HSI_SYS_WAKE_REG(port) (HSI_SYS_WAKE_BASE +\
+ ((port - 1) * HSI_SYS_WAKE_OFFSET))
+#define HSI_SYS_CLEAR_WAKE_BASE 0x0c04
+#define HSI_SYS_CLEAR_WAKE_REG(port) (HSI_SYS_CLEAR_WAKE_BASE +\
+ ((port - 1) * HSI_SYS_WAKE_OFFSET))
+#define HSI_SYS_SET_WAKE_BASE 0x0c08
+#define HSI_SYS_SET_WAKE_REG(port) (HSI_SYS_SET_WAKE_BASE +\
+ ((port - 1) * HSI_SYS_WAKE_OFFSET))
+# define HSI_SSI_WAKE_MASK 0xff /* for SSI */
+# define HSI_WAKE_MASK 0xffff /* for HSI */
+# define HSI_WAKE_4_WIRES (0 << 16)
+# define HSI_WAKE_READY_LVL_0 (0 << 17)
+# define HSI_WAKE(channel) (1 << channel | HSI_WAKE_4_WIRES |\
+ HSI_WAKE_READY_LVL_0)
+
+#define HSI_SYS_HWINFO_REG 0x0004 /* only for HSI */
+
+/* Additional registers definitions (for channels 8 .. 15) for HSI */
+#define HSI_SYS_MPU_U_STATUS_BASE 0x0408
+#define HSI_SYS_MPU_U_STATUS_REG(port, irq) \
+ (HSI_SYS_MPU_U_STATUS_BASE + \
+ (((port - 1) * HSI_SYS_MPU_STATUS_PORT_OFFSET) +\
+ (irq * HSI_SYS_MPU_STATUS_IRQ_OFFSET)))
+
+#define HSI_SYS_MPU_U_ENABLE_BASE 0x040c
+#define HSI_SYS_MPU_U_ENABLE_REG(port, irq) \
+ (HSI_SYS_MPU_U_ENABLE_BASE + \
+ (((port - 1) * HSI_SYS_MPU_ENABLE_PORT_OFFSET) +\
+ (irq * HSI_SYS_MPU_ENABLE_IRQ_OFFSET)))
+
+/*
+ * HSI HST registers
+ */
+#define HSI_HST_ID_REG(port) (HSI_HST_BASE(port) + 0x0000)
+
+#define HSI_HST_MODE_REG(port) (HSI_HST_BASE(port) + 0x0004)
+#define HSI_MODE_VAL_MASK 3
+#define HSI_MODE_SLEEP 0
+#define HSI_MODE_STREAM 1
+#define HSI_MODE_FRAME 2
+#define HSI_SSI_MODE_MULTIPOINTS 3 /* SSI only */
+#define HSI_FLOW_VAL_MASK (3 << 2) /* HSI only */
+#define HSI_FLOW_SYNCHRONIZED (0 << 2) /* HSI only */
+#define HSI_FLOW_PIPELINED (1 << 2) /* HSI only */
+#define HSI_FLOW_REAL_TIME (2 << 2) /* HSI only */
+#define HSI_MODE_WAKE_CTRL_AUTO (1 << 4) /* HSI only */
+#define HSI_MODE_WAKE_CTRL_SW (0 << 4) /* HSI only */
+
+#define HSI_HST_FRAMESIZE_REG(port) (HSI_HST_BASE(port) + 0x0008)
+#define HSI_FRAMESIZE_DEFAULT 31
+#define HSI_FRAMESIZE_MAX 0x1f
+
+#define HSI_HST_TXSTATE_REG(port) (HSI_HST_BASE(port) + 0x000c)
+#define TXSTATE_IDLE 0
+
+#define HSI_HST_BUFSTATE_REG(port) (HSI_HST_BASE(port) + 0x0010)
+#define HSI_HST_BUFSTATE_FIFO_REG(fifo) ((fifo < 8) ? \
+ HSI_HST_BUFSTATE_REG(1) : \
+ HSI_HST_BUFSTATE_REG(2))
+#define HSI_BUFSTATE_CHANNEL(channel) (channel < 8 ? \
+ (1 << channel) : (1 << (channel - 8)))
+
+#define HSI_HST_DIVISOR_REG(port) (HSI_HST_BASE(port) + 0x0018)
+#define HSI_DIVISOR_DEFAULT 1
+#define HSI_SSI_MAX_TX_DIVISOR 0x7f /* for SSI */
+#define HSI_MAX_TX_DIVISOR 0xff /* for HSI */
+
+#define HSI_HST_BREAK_REG(port) (HSI_HST_BASE(port) + 0x0020)
+#define HSI_HST_CHANNELS_REG(port) (HSI_HST_BASE(port) + 0x0024)
+#define HSI_CHANNELS_DEFAULT 4
+#define HSI_SSI_CHANNELS_MAX 8 /* for SSI */
+#define HSI_CHANNELS_MAX 16 /* for HSI */
+
+#define HSI_HST_ARBMODE_REG(port) (HSI_HST_BASE(port) + 0x0028)
+#define HSI_ARBMODE_ROUNDROBIN 0
+#define HSI_ARBMODE_PRIORITY 1
+
+#define HSI_HST_BUFFER_BASE(port) (HSI_HST_BASE(port) + 0x0080)
+#define HSI_HST_BUFFER_CH_REG(port, channel) (HSI_HST_BUFFER_BASE(port) +\
+ (channel * 4))
+#define HSI_HST_BUFFER_FIFO_REG(fifo) ((fifo < 8) ? \
+ (HSI_HST_BUFFER_CH_REG(1, fifo)) : \
+ (HSI_HST_BUFFER_CH_REG(2, fifo - 8)))
+
+#define HSI_HST_SWAPBUF_BASE(port) (HSI_HST_BASE(port) + 0x00c0)
+#define HSI_HST_SWAPBUF_CH_REG(port, channel) (HSI_HST_SWAPBUF_BASE(port) +\
+ (channel * 4))
+
+/* Additional registers for HSI */
+#define HSI_HST_FIFO_COUNT 16
+#define HSI_HST_MAPPING_FIFO_REG(fifo) (HSI_HST_BASE(1) + 0x0100 +\
+ (fifo * 4))
+#define HSI_MAPPING_ENABLE 1
+#define HSI_MAPPING_CH_NUMBER_OFFSET 1
+#define HSI_MAPPING_PORT_NUMBER_OFFSET 7
+#define HSI_HST_MAPPING_THRESH_OFFSET 10
+#define HSI_HST_MAPPING_THRESH_VALUE (0x0 << HSI_HST_MAPPING_THRESH_OFFSET)
+
+/*
+ * HSI HSR registers
+ */
+#define HSI_HSR_ID_REG(port) (HSI_HSR_BASE(port) + 0x0000)
+
+#define HSI_HSR_MODE_REG(port) (HSI_HSR_BASE(port) + 0x0004)
+
+#define HSI_HSR_FRAMESIZE_REG(port) (HSI_HSR_BASE(port) + 0x0008)
+
+#define HSI_HSR_RXSTATE_REG(port) (HSI_HSR_BASE(port) + 0x000c)
+
+#define HSI_HSR_BUFSTATE_REG(port) (HSI_HSR_BASE(port) + 0x0010)
+#define HSI_HSR_BUFSTATE_FIFO_REG(fifo) ((fifo < 8) ? \
+ HSI_HSR_BUFSTATE_REG(1) : \
+ HSI_HSR_BUFSTATE_REG(2))
+
+#define HSI_HSR_BREAK_REG(port) (HSI_HSR_BASE(port) + 0x001c)
+
+#define HSI_HSR_ERROR_REG(port) (HSI_HSR_BASE(port) + 0x0020)
+#define HSI_HSR_ERROR_SIG 1
+#define HSI_HSR_ERROR_FTE (1 << 1) /* HSI only */
+#define HSI_HSR_ERROR_TBE (1 << 4) /* HSI only */
+#define HSI_HSR_ERROR_RME (1 << 7) /* HSI only */
+#define HSI_HSR_ERROR_TME (1 << 11) /* HSI only */
+
+#define HSI_HSR_ERRORACK_REG(port) (HSI_HSR_BASE(port) + 0x0024)
+
+#define HSI_HSR_CHANNELS_REG(port) (HSI_HSR_BASE(port) + 0x0028)
+
+#define HSI_HSR_OVERRUN_REG(port) (HSI_HSR_BASE(port) + 0x002c)
+
+#define HSI_HSR_OVERRUNACK_REG(port) (HSI_HSR_BASE(port) + 0x0030)
+
+#define HSI_HSR_COUNTERS_REG(port) (HSI_HSR_BASE(port) + 0x0034)
+#define HSI_TIMEOUT_DEFAULT 0 /* SSI only */
+#define HSI_SSI_RX_TIMEOUT_MAX 0x1ff /* SSI only */
+#define HSI_COUNTERS_FT_MASK 0x000fffff /* HSI only */
+#define HSI_COUNTERS_TB_MASK 0x00f00000 /* HSI only */
+#define HSI_COUNTERS_FB_MASK 0xff000000 /* HSI only */
+#define HSI_COUNTERS_FT_OFFSET 0 /* HSI only */
+#define HSI_COUNTERS_TB_OFFSET 20 /* HSI only */
+#define HSI_COUNTERS_FB_OFFSET 24 /* HSI only */
+/* Default FT value: 2 x max_bits_per_frame + 20% margin */
+#define HSI_COUNTERS_FT_DEFAULT (90 << HSI_COUNTERS_FT_OFFSET)
+#define HSI_COUNTERS_TB_DEFAULT (6 << HSI_COUNTERS_TB_OFFSET)
+#define HSI_COUNTERS_FB_DEFAULT (8 << HSI_COUNTERS_FB_OFFSET)
+
+#define HSI_HSR_BUFFER_BASE(port) (HSI_HSR_BASE(port) + 0x0080)
+#define HSI_HSR_BUFFER_CH_REG(port, channel) (HSI_HSR_BUFFER_BASE(port) +\
+ (channel * 4))
+#define HSI_HSR_BUFFER_FIFO_REG(fifo) ((fifo < 8) ? \
+ (HSI_HSR_BUFFER_CH_REG(1, fifo)) : \
+ (HSI_HSR_BUFFER_CH_REG(2, fifo - 8)))
+
+#define HSI_HSR_SWAPBUF_BASE(port) (HSI_HSR_BASE(port) + 0x00c0)
+#define HSI_HSR_SWAPBUF_CH_REG(port, channel) (HSI_HSR_SWAPBUF_BASE +\
+ (channel * 4))
+
+/* Additional registers for HSI */
+#define HSI_HSR_FIFO_COUNT 16
+#define HSI_HSR_MAPPING_FIFO_REG(fifo) (HSI_HSR_BASE(1) + 0x0100 +\
+ (fifo * 4))
+#define HSI_HSR_MAPPING_WORDS_MASK (0xf << 10)
+
+#define HSI_HSR_DLL_REG(port) (HSI_HSR_BASE(port) + 0x0144)
+#define HSI_HSR_DLL_COCHRE 1
+#define HSI_HSR_DLL_COCHGR (1 << 4)
+#define HSI_HSR_DLL_INCO_MASK 0x0003ff00
+#define HSI_HSR_DLL_INCO_OFFSET 8
+
+#define HSI_HSR_DIVISOR_REG(port) (HSI_HSR_BASE(port) + 0x014C)
+#define HSI_HSR_DIVISOR_MASK 0xff
+#define HSI_MAX_RX_DIVISOR 0xff
+
+
+/*
+ * HSI GDD registers
+ */
+#define HSI_SSI_GDD_HW_ID_REG (HSI_GDD_BASE + 0x0000)
+
+#define HSI_SSI_GDD_PPORT_ID_REG (HSI_GDD_BASE + 0x0010)
+
+#define HSI_SSI_GDD_MPORT_ID_REG (HSI_GDD_BASE + 0x0014)
+
+#define HSI_SSI_GDD_PPORT_SR_REG (HSI_GDD_BASE + 0x0020)
+#define HSI_PPORT_ACTIVE_LCH_NUMBER_MASK 0xff
+
+#define HSI_GDD_MPORT_SR_REG (HSI_GDD_BASE + 0x0024)
+#define HSI_SSI_MPORT_ACTIVE_LCH_NUMBER_MASK 0xff
+
+#define HSI_SSI_GDD_TEST_REG (HSI_GDD_BASE + 0x0040)
+#define HSI_SSI_TEST 1
+
+#define HSI_GDD_GCR_REG (HSI_GDD_BASE + 0x0100)
+#define HSI_CLK_AUTOGATING_ON (1 << 3)
+#define HSI_SWITCH_OFF (1 << 0)
+
+#define HSI_GDD_GRST_REG (HSI_GDD_BASE + 0x0200)
+#define HSI_SWRESET 1
+
+#define HSI_GDD_CSDP_BASE (HSI_GDD_BASE + 0x0800)
+#define HSI_GDD_CSDP_OFFSET 0x40
+#define HSI_GDD_CSDP_REG(channel) (HSI_GDD_CSDP_BASE +\
+ (channel * HSI_GDD_CSDP_OFFSET))
+#define HSI_DST_BURST_EN_MASK 0xc000
+#define HSI_DST_SINGLE_ACCESS0 0
+#define HSI_DST_SINGLE_ACCESS (1 << 14)
+#define HSI_DST_BURST_4X32_BIT (2 << 14)
+#define HSI_DST_BURST_8x32_BIT (3 << 14)
+
+#define HSI_DST_MASK 0x1e00
+#define HSI_DST_MEMORY_PORT (8 << 9)
+#define HSI_DST_PERIPHERAL_PORT (9 << 9)
+
+#define HSI_SRC_BURST_EN_MASK 0x0180
+#define HSI_SRC_SINGLE_ACCESS0 0
+#define HSI_SRC_SINGLE_ACCESS (1 << 7)
+#define HSI_SRC_BURST_4x32_BIT (2 << 7)
+#define HSI_SRC_BURST_8x32_BIT (3 << 7)
+
+#define HSI_SRC_MASK 0x003c
+#define HSI_SRC_MEMORY_PORT (8 << 2)
+#define HSI_SRC_PERIPHERAL_PORT (9 << 2)
+
+#define HSI_DATA_TYPE_MASK 3
+#define HSI_DATA_TYPE_S32 2
+
+#define HSI_GDD_CCR_BASE (HSI_GDD_BASE + 0x0802)
+#define HSI_GDD_CCR_OFFSET 0x40
+#define HSI_GDD_CCR_REG(channel) (HSI_GDD_CCR_BASE +\
+ (channel * HSI_GDD_CCR_OFFSET))
+#define HSI_DST_AMODE_MASK (3 << 14)
+#define HSI_DST_AMODE_CONST 0
+#define HSI_DST_AMODE_POSTINC (1 << 14)
+
+#define HSI_SRC_AMODE_MASK (3 << 12)
+#define HSI_SRC_AMODE_CONST 0
+#define HSI_SRC_AMODE_POSTINC (1 << 12)
+
+#define HSI_CCR_ENABLE (1 << 7)
+
+#define HSI_CCR_SYNC_MASK 0x001f /* only for SSI */
+
+#define HSI_GDD_CICR_BASE (HSI_GDD_BASE + 0x0804)
+#define HSI_GDD_CICR_OFFSET 0x40
+#define HSI_GDD_CICR_REG(channel) (HSI_GDD_CICR_BASE +\
+ (channel * HSI_GDD_CICR_OFFSET))
+#define HSI_BLOCK_IE (1 << 5)
+#define HSI_HALF_IE (1 << 2)
+#define HSI_TOUT_IE (1 << 0)
+
+#define HSI_GDD_CSR_BASE (HSI_GDD_BASE + 0x0806)
+#define HSI_GDD_CSR_OFFSET 0x40
+#define HSI_GDD_CSR_REG(channel) (HSI_GDD_CSR_BASE +\
+ (channel * HSI_GDD_CSR_OFFSET))
+#define HSI_CSR_SYNC (1 << 6)
+#define HSI_CSR_BLOCK (1 << 5)
+#define HSI_CSR_HALF (1 << 2)
+#define HSI_CSR_TOUT (1 << 0)
+
+#define HSI_GDD_CSSA_BASE (HSI_GDD_BASE + 0x0808)
+#define HSI_GDD_CSSA_OFFSET 0x40
+#define HSI_GDD_CSSA_REG(channel) (HSI_GDD_CSSA_BASE +\
+ (channel * HSI_GDD_CSSA_OFFSET))
+
+#define HSI_GDD_CDSA_BASE (HSI_GDD_BASE + 0x080c)
+#define HSI_GDD_CDSA_OFFSET 0x40
+#define HSI_GDD_CDSA_REG(channel) (HSI_GDD_CDSA_BASE +\
+ (channel * HSI_GDD_CDSA_OFFSET))
+
+#define HSI_GDD_CEN_BASE (HSI_GDD_BASE + 0x0810)
+#define HSI_GDD_CEN_OFFSET 0x40
+#define HSI_GDD_CEN_REG(channel) (HSI_GDD_CEN_BASE +\
+ (channel * HSI_GDD_CEN_OFFSET))
+
+#define HSI_GDD_CSAC_BASE (HSI_GDD_BASE + 0x0818)
+#define HSI_GDD_CSAC_OFFSET 0x40
+#define HSI_GDD_CSAC_REG(channel) (HSI_GDD_CSAC_BASE +\
+ (channel * HSI_GDD_CSAC_OFFSET))
+
+#define HSI_GDD_CDAC_BASE (HSI_GDD_BASE + 0x081a)
+#define HSI_GDD_CDAC_OFFSET 0x40
+#define HSI_GDD_CDAC_REG(channel) (HSI_GDD_CDAC_BASE +\
+ (channel * HSI_GDD_CDAC_OFFSET))
+
+#define HSI_SSI_GDD_CLNK_CTRL_BASE (HSI_GDD_BASE + 0x0828)
+#define HSI_SSI_GDD_CLNK_CTRL_OFFSET 0x40
+#define HSI_SSI_GDD_CLNK_CTRL_REG(channel) (HSI_SSI_GDD_CLNK_CTRL_BASE +\
+ (channel * HSI_SSI_GDD_CLNK_CTRL_OFFSET))
+
+#define HSI_SSI_ENABLE_LNK (1 << 15)
+#define HSI_SSI_STOP_LNK (1 << 14)
+#define HSI_SSI_NEXT_CH_ID_MASK 0xf
+
+/*
+ * HSI Helpers
+ */
+#define HSI_SYS_MPU_ENABLE_CH_REG(port, irq, channel) \
+ ((channel < HSI_SSI_CHANNELS_MAX) ? \
+ HSI_SYS_MPU_ENABLE_REG(port, irq) : \
+ HSI_SYS_MPU_U_ENABLE_REG(port, irq))
+
+/**
+ * struct omap_ssi_config - SSI board configuration
+ * @num_ports: Number of ports in use
+ * @cawake_line: Array of cawake gpio lines
+ */
+struct omap_ssi_board_config {
+ unsigned int num_ports;
+ int cawake_gpio[2];
+};
+extern int omap_ssi_config(struct omap_ssi_board_config *ssi_config);
+
+/**
+ * struct omap_hsi_config - HSI board configuration
+ * @num_ports: Number of ports in use
+ */
+struct omap_hsi_board_config {
+ unsigned int num_ports;
+};
+extern int omap_hsi_config(struct omap_hsi_board_config *hsi_config);
+
+#endif /* __HSI_H__ */