@@ -166,6 +166,12 @@ config MUSB_USE_SYSTEM_DMA_WORKAROUND
DMA channels are simultaneously enabled. To work around this issue,
you can choose to use System DMA for RX channels.
+ Also on Mentor DMA in MUSB RTL version 1.8 (OMAP3630, AM/DM37x)
+ requires buffers to be aligned on a four byte boundary. This affects
+ USB CDC/RNDIS class application where buffers are always unaligned.
+ To work around this issue, you can choose to use System DMA for
+ unaligned buffers.
+
config USB_TI_CPPI_DMA
bool
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
@@ -52,8 +52,7 @@ static void musb_sdma_channel_program(struct musb *musb,
struct musb_dma_channel *musb_channel,
dma_addr_t dma_addr, u32 len)
{
- /* System DMA */
- /* RX: set src = FIFO */
+ /* set transfer parameters */
omap_set_dma_transfer_params(musb_channel->sysdma_channel,
OMAP_DMA_DATA_TYPE_S8,
len ? len : 1, 1, /* One frame */
@@ -61,20 +60,39 @@ static void musb_sdma_channel_program(struct musb *musb,
OMAP24XX_DMA_NO_DEVICE,
0); /* Src Sync */
- omap_set_dma_src_params(musb_channel->sysdma_channel, 0,
- OMAP_DMA_AMODE_CONSTANT,
- MUSB_FIFO_ADDRESS(musb->ctrl_phys_base,
- musb_channel->epnum),
- 0, 0);
-
- omap_set_dma_dest_params(musb_channel->sysdma_channel, 0,
- OMAP_DMA_AMODE_POST_INC, dma_addr,
- 0, 0);
-
- omap_set_dma_dest_data_pack(musb_channel->sysdma_channel, 1);
- omap_set_dma_dest_burst_mode(musb_channel->sysdma_channel,
- OMAP_DMA_DATA_BURST_16);
-
+ if (!musb_channel->transmit) {
+ /* RX: set src = FIFO */
+ omap_set_dma_src_params(musb_channel->sysdma_channel, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ MUSB_FIFO_ADDRESS(musb->ctrl_phys_base,
+ musb_channel->epnum),
+ 0, 0);
+
+ omap_set_dma_dest_params(musb_channel->sysdma_channel, 0,
+ OMAP_DMA_AMODE_POST_INC, dma_addr,
+ 0, 0);
+
+ omap_set_dma_dest_data_pack(musb_channel->sysdma_channel, 1);
+ omap_set_dma_dest_burst_mode(musb_channel->sysdma_channel,
+ OMAP_DMA_DATA_BURST_16);
+
+ } else if (musb_channel->transmit) {
+ /* TX: set dst = FIFO */
+ omap_set_dma_src_params(musb_channel->sysdma_channel, 0,
+ OMAP_DMA_AMODE_POST_INC, dma_addr,
+ 0, 0);
+
+ omap_set_dma_dest_params(musb_channel->sysdma_channel, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ MUSB_FIFO_ADDRESS(musb->ctrl_phys_base,
+ musb_channel->epnum),
+ 0, 0);
+
+ omap_set_dma_dest_data_pack(musb_channel->sysdma_channel, 0);
+ omap_set_dma_dest_burst_mode(musb_channel->sysdma_channel,
+ OMAP_DMA_DATA_BURST_DIS);
+ }
+ /* start the system dma */
omap_start_dma(musb_channel->sysdma_channel);
}
static void musb_sysdma_completion(int lch, u16 ch_status, void *data)
@@ -88,12 +106,18 @@ static void musb_sysdma_completion(int lch, u16 ch_status, void *data)
(struct musb_dma_channel *) data;
struct musb_dma_controller *controller = musb_channel->controller;
struct musb *musb = controller->private_data;
+ void __iomem *mbase = controller->base;
+
channel = &musb_channel->channel;
DBG(2, "lch = 0x%d, ch_status = 0x%x\n", lch, ch_status);
spin_lock_irqsave(&musb->lock, flags);
- addr = (u32) omap_get_dma_dst_pos(musb_channel->sysdma_channel);
+ if (musb_channel->transmit)
+ addr = (u32) omap_get_dma_src_pos(musb_channel->sysdma_channel);
+ else
+ addr = (u32) omap_get_dma_dst_pos(musb_channel->sysdma_channel);
+
if (musb_channel->len == 0)
channel->actual_len = 0;
else
@@ -106,6 +130,26 @@ static void musb_sysdma_completion(int lch, u16 ch_status, void *data)
"=> reconfig 0 " : " => complete");
channel->status = MUSB_DMA_STATUS_FREE;
+
+ /* completed */
+ if ((musb_channel->transmit) && (channel->desired_mode == 0)
+ && (channel->actual_len == musb_channel->max_packet_sz)) {
+
+ u8 epnum = musb_channel->epnum;
+ int offset = MUSB_EP_OFFSET(epnum,
+ MUSB_TXCSR);
+ u16 txcsr;
+
+ /*
+ * The programming guide says that we
+ * must clear DMAENAB before DMAMODE.
+ */
+ musb_ep_select(mbase, epnum);
+ txcsr = musb_readw(mbase, offset);
+ txcsr |= MUSB_TXCSR_TXPKTRDY;
+ musb_writew(mbase, offset, txcsr);
+ }
+
musb_dma_completion(musb, musb_channel->epnum, musb_channel->transmit);
spin_unlock_irqrestore(&musb->lock, flags);
@@ -194,8 +238,15 @@ static struct dma_channel *dma_channel_allocate(struct dma_controller *c,
* issue when TX and RX DMA channels are simultaneously
* enabled. To work around this issue, use system DMA
* for all RX channels.
+ * Also on MUSB RTL version 1.8 onward (OMAP3630, OMAP4
+ * and AM/DM37x) DMA requires buffers to be aligned on
+ * a four byte boundary. This affects USB CDC/RNDIS
+ * class application where buffers are always unaligned.
+ * Using system DMA for unaligned buffers as a
+ * workaround for this issue.
*/
- if (((musb->hwvers == MUSB_HWVERS_1400) && !transmit)
+ if ((((musb->hwvers == MUSB_HWVERS_1400) && !transmit)
+ || (musb->hwvers >= MUSB_HWVERS_1800))
&& use_sdma_workaround()) {
int ret;
ret = musb_sdma_channel_request(
@@ -248,11 +299,18 @@ static void configure_channel(struct dma_channel *channel,
struct musb *musb = controller->private_data;
void __iomem *mbase = controller->base;
u8 bchannel = musb_channel->idx;
+ u8 buffer_is_aligned = (dma_addr & 0x3) ? 0 : 1;
+ u8 use_sdma = (musb_channel->sysdma_channel == -1) ? 0 : 1;
u16 csr = 0;
DBG(4, "%p, pkt_sz %d, addr 0x%x, len %d, mode %d\n",
channel, packet_sz, dma_addr, len, mode);
- if (musb_channel->sysdma_channel != -1) {
+
+ if (buffer_is_aligned && (packet_sz >= 512) &&
+ (musb->hwvers >= MUSB_HWVERS_1800))
+ use_sdma = 0;
+
+ if (use_sdma) {
musb_sdma_channel_program(musb, musb_channel, dma_addr, len);
} else { /* Mentor DMA */
@@ -328,6 +386,9 @@ static int dma_channel_abort(struct dma_channel *channel)
u16 csr;
if (channel->status == MUSB_DMA_STATUS_BUSY) {
+ if (musb_channel->sysdma_channel != -1)
+ musb_sdma_channel_abort(musb_channel->sysdma_channel);
+
if (musb_channel->transmit) {
offset = MUSB_EP_OFFSET(musb_channel->epnum,
MUSB_TXCSR);
@@ -342,10 +403,6 @@ static int dma_channel_abort(struct dma_channel *channel)
csr &= ~MUSB_TXCSR_DMAMODE;
musb_writew(mbase, offset, csr);
} else {
- if (musb_channel->sysdma_channel != -1)
- musb_sdma_channel_abort(
- musb_channel->sysdma_channel);
-
offset = MUSB_EP_OFFSET(musb_channel->epnum,
MUSB_RXCSR);