@@ -38,22 +38,28 @@
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
#define IGEP2_GPIO_USBH_NRESET 24
-#define IGEP2_GPIO_LED0_GREEN 26
-#define IGEP2_GPIO_LED0_RED 27
-#define IGEP2_GPIO_LED1_RED 28
-#define IGEP2_GPIO_DVI_PUP 170
-#define IGEP2_GPIO_WIFI_NPD 94
-#define IGEP2_GPIO_WIFI_NRESET 95
+#define IGEP2_GPIO_LED0_GREEN 26
+#define IGEP2_GPIO_LED0_RED 27
+#define IGEP2_GPIO_LED1_RED 28
+#define IGEP2_GPIO_DVI_PUP 170
+
+#define IGEP2_RB_GPIO_WIFI_NPD 94
+#define IGEP2_RB_GPIO_WIFI_NRESET 95
+#define IGEP2_RB_GPIO_BT_NRESET 137
+#define IGEP2_RC_GPIO_WIFI_NPD 138
+#define IGEP2_RC_GPIO_WIFI_NRESET 139
+#define IGEP2_RC_GPIO_BT_NRESET 137
/*
* IGEP2 Hardware Revision Table
*
- * --------------------------
- * | Id. | Hw Rev. | HW0 (28) |
- * --------------------------
- * | 0 | B/C | high |
- * | 1 | C | low |
- * --------------------------
+ * --------------------------------------------------------------------------
+ * | Id. | Hw Rev. | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET |
+ * --------------------------------------------------------------------------
+ * | 0 | B | high | gpio94 | gpio95 | - |
+ * | 0 | B/C (B-compatible) | high | gpio94 | gpio95 | gpio137 |
+ * | 1 | C | low | gpio138 | gpio139 | gpio137 |
+ * --------------------------------------------------------------------------
*/
#define IGEP2_BOARD_HWREV_B 0
@@ -295,12 +301,14 @@ static struct omap2_hsmmc_info mmc[] = {
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
{
.mmc = 2,
.wires = 4,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
+#endif
{} /* Terminator */
};
@@ -577,6 +585,50 @@ static struct omap_board_mux board_mux[] __initdata = {
#define board_mux NULL
#endif
+#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+
+static void __init igep2_wlan_bt_init(void)
+{
+ unsigned npd, wreset, btreset;
+
+ /* GPIO's for WLAN-BT combo depends on hardware revision */
+ if (hwrev == IGEP2_BOARD_HWREV_B) {
+ npd = IGEP2_RB_GPIO_WIFI_NPD;
+ wreset = IGEP2_RB_GPIO_WIFI_NRESET;
+ btreset = IGEP2_RB_GPIO_BT_NRESET;
+ } else if (hwrev == IGEP2_BOARD_HWREV_C) {
+ npd = IGEP2_RC_GPIO_WIFI_NPD;
+ wreset = IGEP2_RC_GPIO_WIFI_NRESET;
+ btreset = IGEP2_RC_GPIO_BT_NRESET;
+ } else
+ return;
+
+ /* Set GPIO's for WLAN-BT combo module */
+ if ((gpio_request(npd, "GPIO_WIFI_NPD") == 0) &&
+ (gpio_direction_output(npd, 1) == 0)) {
+ gpio_export(npd, 0);
+ } else
+ pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NPD\n");
+
+ if ((gpio_request(wreset, "GPIO_WIFI_NRESET") == 0) &&
+ (gpio_direction_output(wreset, 1) == 0)) {
+ gpio_export(wreset, 0);
+ gpio_set_value(wreset, 0);
+ udelay(10);
+ gpio_set_value(wreset, 1);
+ } else
+ pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NRESET\n");
+
+ if ((gpio_request(btreset, "GPIO_BT_NRESET") == 0) &&
+ (gpio_direction_output(btreset, 1) == 0)) {
+ gpio_export(btreset, 0);
+ } else
+ pr_warning("IGEP2: Could not obtain gpio GPIO_BT_NRESET\n");
+}
+#else
+static inline void __init igep2_wlan_bt_init(void) { }
+#endif
+
static void __init igep2_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -595,22 +647,12 @@ static void __init igep2_init(void)
igep2_display_init();
igep2_init_smsc911x();
- /* GPIO W-LAN + Bluetooth combo module */
- if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
- gpio_export(IGEP2_GPIO_WIFI_NPD, 0);
-/* gpio_set_value(IGEP2_GPIO_WIFI_NPD, 0); */
- } else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NPD\n");
+ /*
+ * WLAN-BT combo module from MuRata wich has a Marvell WLAN
+ * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
+ */
+ igep2_wlan_bt_init();
- if ((gpio_request(IGEP2_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_WIFI_NRESET, 1) == 0)) {
- gpio_export(IGEP2_GPIO_WIFI_NRESET, 0);
- gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 0);
- udelay(10);
- gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 1);
- } else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NRESET\n");
}
MACHINE_START(IGEP0020, "IGEP v2 board")